Cisco Switching/Routing :: 10.0.2.1 / Routing Over A Point To Point Ethernet Connection?

Feb 15, 2012

I have 2 data centers miles apart. They are on a Paetec  MPLS. I have a Lightower point to point Ethernet link between the two data centers as well.  At data center A, I have a Paetec managed router (192.168.2.1). The subnets behind that router are 192.168.2.0, 192.168.100.0 and 192.168.101.0. I also have a Cisco 1841 that is configured with fa0 addressed as 192.168.2.250 and fa1 as 10.5.5.1. Fa1 is the one end of the point to point Ethernet link to data center B.At data center B, I have a Paetec managed router (10.0.2.1). The subnets behind that router are 10.0.2.0, 10.0.100.0 and 10.0.101.0. I also have a Cisco 1841 that is configured with fa0 addressed as 10.0.2.250 and fa1 as 10.5.5.2.What I want to happen is any traffic headed from data center A destined for 10.0.100.0 or 10.0.101.0 to be routed through the point to point Ethernet link. I had Paetec add routes in their managed router to route any traffic headed for 10.0.100.0 and 10.0.101.0 to my Cisco 1841 (192.168.2.250).I wanted to do the same for traffic destined for 192.168.100.0 and 192.168.101.0 from data center B. Paetec added the appropriate routes to the router at data center B.Now, if I trace from data center A to 10.0.100.45, I see this:

1   <1 ms   <1 ms   <1 ms 192.168.2.1
2   <1 ms   <1 ms   <1 ms 192.168.2.250
3     4 ms     4 ms     4 ms 10.5.5.2
4     3 ms     3 ms     3 ms 10.0.2.1
 
So the routing seems to be ok. However after it hits 10.0.2.1, it gets lost after that.Am I missing something? Is this a misconfiguration on Paetec’s routers?

View 1 Replies


ADVERTISEMENT

Cisco Switching/Routing :: 2960 To Assign 2MB To Point To Point Connection For Voice Vlan

Sep 11, 2012

recently i just connected a non cisco ip phone(from panasonic) to Cisco 2960 POE switch at site A. The PABX system is located at site B,Site A and site B are connected using MetroE Point to point.I would like to apply QoS for voice vlan. I want to assign 2MB to the point to point connection for voice vlan.

View 3 Replies View Related

Cisco Switching/Routing :: 1941 / K9 VPN Router MPLS IPVPN Point-to-point

Mar 15, 2012

I have 2 cisco 1941/K9 vpn router. I have configured both with LAN ip address given by our vpn provider which is 172.10.10.1 and the other is 172.10.20.1. Both IP addresses are configured to GigabitEthernet port 0/0 on both routers.
 
1. Is it possible to configure our own set of ip address like 10.71.10.1 and 10.71.50.1 on the GE 0/0 port?

2. Or can we configure our own set of ip addresses (10.71.10.1 and 10.71.50.1) to GigabitEthernet port 0/1 and maintain the other ip addresses on port 0/0?
 
The first purpose is to have our own set of ip addresses for LAN connection and I will be able to connect or telnet whichever ip address or port is up.

View 0 Replies View Related

Cisco WAN :: Point To Point Ethernet Circuit - 802.1q?

Jul 15, 2012

Is it possible to run 802.1Q on a point to point Ethernet circuit between 2 Cisco ISR routers? I need to carry multiple VLANs across an ethernet WAN circuit but not sure if a Cisco router would let me do this. I can surely lab up but was looking for expert opinion on what's best aproach to carry multiple VLAN across the WAN ethernet. Plugging the circuit to a LAN switch is not an option since this is a managed WAN router.

View 10 Replies View Related

Cisco Switches :: SG500x Point To Point Connection Very Slow After 1.30.59 Update

May 1, 2013

I have a point to point 100mb line connecting SG500x switches at 2 locations, with these ports in a vlan together. I use layer 3 on the SG500x's to route between the two sites. I also have RIP protocol enabled to allow for automatic failover if the point to point fails (this works well).
 
I upgraded the ios to 1.30.59, and the connection now runs at a fraction of the speed. I have hard-coded the ports to run at 100mb full duplex, but I still only get around 12mb of throughput between the switches. I used to get about 90mb before. The provider also hard-coded the circuit to 100mb full duplex. The provider has checked the circuit remotely, and everything looks fine. I tested with a laptop at each side, and did get almost 70mb throughput. I would think this indicates some type of setting mismatch, but i cannot find anything.
 
I am using a backup vpn for now as some things look flaky as well (on vpn, I can use the web interface to access the SG500x on the opposite side, but on the point to point I cannot - I can ping the device though).
 
I have seen some references on here to shutting off STP on these 2 ports.

View 3 Replies View Related

Cisco WAN :: Point To Point Connection In L2TPv3 With A Bandwidth Pass Through Of 1 Gb

Sep 4, 2012

I would to realize an point to point connection in L2TPv3 with a bandwidth pass through of 1 Gb. Which routers/switches I can use?

View 3 Replies View Related

Cisco Wireless :: 3502p - Access Point Support MESH And Point-to-Point Bridging?

Apr 16, 2013

I need to know if 3502p with outdoor antennas supports Point-to-Point Wireless Bridging?

View 6 Replies View Related

Cisco WAN :: 1760 Point To Point Fiber Connection

Feb 28, 2012

We have two locations 10 miles apart and need connectivity between them. A local provider can run a 30MB fiber connection between the 2 sites at a very reasonable cost. We would have to provide the routers however. I have worked with Cisco routers before with T1 channelized connections but am unsure how the the fiber would connect to a Cisco router in this scenerio. I need to know how such a connection to the routers at each end would take place, specifically what WIC or whatever else would be needed. I currently have a 1760 router at each site but realize that they are old and I m,ay have to replace them with newer models.

View 11 Replies View Related

Redirect Network Traffic Through A Point To Point Connection?

Jul 14, 2011

We have a point to point connection going from a regional office to the main office this is provided by a Service Provider. In our office we have an ISP and what we need to prevent from happening is that if the internet drops from the ISP we could somehow re-direct the internet traffic through this point to point connection and make it so that our Internet connection is pulled from the main office. is it just a matter of re-configuring?

View 5 Replies View Related

Cisco Wireless :: Point To Point Access Point 1262 Bridging

Feb 27, 2013

How would I bridge a wireless connection with a distance of 400 feet? Would twoAP1262N-A-K9 be able to make this happen? Or is there another wireless bridge that you all can think of?I would be connecting one AP1262 of off a 3750g switch and at the far end (400 ft aproximately) another AP1262N-A-K9.

View 12 Replies View Related

Cisco Switching/Routing :: Using 871W As Additional Access Point

Apr 25, 2012

I have an 871w set up to add wireless connectivity to an existing network. When adding a client to the physical interfaces to test VLAN internet connectivity, however, a DHCP address is assigned but internet traffic on the terminal never reaches the network nor does the network recognize the IP the terminal shows as being 'connected'. Also, pings sourced from the VLAN do reach destinations. I've attached my config file, I think it's a routing issue of some kind.
 
10.26.99.0 is the existing network. 10.26.99.1 is an existing 871w router set as the DHCP server for that network and 10.26.99.10 is a Windows Server 2003 DNS box. VLAN 2 and DHCP pool alpha were control sets for trialing DNS settings.

View 10 Replies View Related

Cisco Switching/Routing :: 1130 / Access Point Not Working?

Feb 14, 2012

I have a 1130 cisco access point,we are using this for wireless cisco IP phone connectivity to the network.Earlier access point was woring fine and we were able to make calls through IP phone.But we have relocated to new place.Now the access point is not working and we are not able to make the calls on the wireless IP phone as the access point is not working.But the access is in the netwrok and we are able to ping the IP address of the Access point.
  
We are contonuously getting the below loggs on Access point and the access point is getting power from the ethernet port of the switch not through the external powerr adaptor.
 
error message:
: %CDP_PD-2-POWER_LOW: All radios disabled - NEGOTIATED WS-C
4507R (0012.7fb6.6e6c).
 
how to make this work.

View 6 Replies View Related

Cisco Switching/Routing :: SG300 Restrict Port To Only One Access Point

Jun 10, 2012

On a small Bording School we have the students living in several small houses, each equipped with an AP.Each Ap serve 4 Vlans.I want to restrict the switch for these AP, in a way to keep the students from removing the AP and connecting their own equipment.I tried using the secure port feature on the SG300, but that had the result of allowing the AP but denying all the users connected to the AP.The switch is a SG300-28P placed in L3 mode.

View 3 Replies View Related

Cisco Switching/Routing :: AIR-CAP1602I-N Access Point Compatibility With AIR-WLC2112-K9

May 22, 2013

I have Cisco Access point AIR-CAP1602I-N-K9 ,My doubt is,is this AP support on WLC AIR-WLC2112-K9

View 1 Replies View Related

Cisco Switching/Routing :: Connect HP 420 Access Point To 4500 Switch

Apr 3, 2012

i am trying to configure my HP 420 access point. I have configure different  SSID on it, This access point is connected to cisco 4500 switch, i have configure trunk on up link to  access point.my problem is the client are not able to get an IP address form the correct vlan if i tagged the SSID to it.

in the following the output of show run int in cisco 4500 switch:
 
interface GigabitEthernet3/13 
description ==== HP ACCess point ====
 switchport trunk allowed vlan 99,130,132 
switchport mode trunk

[code]....

View 1 Replies View Related

Cisco Switching/Routing :: Access Point Aironet 1040 Configuration - Not Getting 802.11n To Work?

Jun 25, 2012

I can't figure out how to get the config right for the 802.11n channel to work.

View 4 Replies View Related

Cisco Switching/Routing :: 881w-gn-a-k9 Access Point Not Serving DHCP Addresses

Jan 27, 2013

i have to Bridge the AP to VLAN1 which has the DHCP pool. For some reason when I try to do this from iOS console it tells me that gig0 is not a bridgable interface. I am newb to Cisco iOS (24 hours new ). I got the Cisco Configuration Professional working and would like to fix my issue through there if possible? why my AP wont get anything but APIPA addresses?

version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption

[code]....

View 13 Replies View Related

Cisco Switching/Routing :: 3560 Default QOS Trust Behavior On Access Point Changed

Oct 27, 2011

I've just been testing QOS on 3560 with version 15.0(1) and it seems the the default qos trust behavior on access ports has changed. By default the trust state of a port is not to trust anything, however rather than rewriting the DSCP value of the incoming packets and settign it to 0 the switch now seems to leave the DSCP value unchanged.
 
SW04-C3560(config)# do sh mls qos int g0/2
GigabitEthernet0/2
trust state: not trusted
trust mode: not trusted
trust enabled flag: ena
[Code]......

View 4 Replies View Related

Cisco Switching/Routing :: 3600 Accessing Wireless Access Point From Remote Subnet

Mar 28, 2013

I recently installed a couple of Cisco Aironet 3600 Series Wireless Access Points at a remote site. While I was at the site everything seemed OK, The clients were able to get connected to the access points, the guest network worked fine, I could SSH into the access points, and I could ping them. The problem is when I went back to my home site I tried to SSH into the access points through an ASA IPSec VPN Tunnel and it couldn’t find it. When I try to ping the access points they “time out”. I can ping and connect all other addresses (via RDP, HTTP, etc..) on the same subnet which should rule out an access list problem. A couple of notes to be aware of:
 
The WAP’s have the Autonomous IOS installed (Version 15.2(2)JB) The WAP’s are connected to Dell PowerConnect 5724 (Not by choice.. We are a Cisco shop, these were already there and have plans this year to replace) 

I can ping and SSH with Putty to the WAP’s from the local subnet I cannot ping or SSH from a remote subnet to the WAP’s. I can access all other IP’s and Computers from a remote subnet.

View 12 Replies View Related

Cisco Switching/Routing :: 4500 / 3560 - DHCP Redundancy - IP Helper Address Point To HSRP?

Jan 5, 2012

My actual Scenario
 
1 x 4500 and 1 x 3560?They are gateways of 8 Vlans?They are doing HSRP in each of those Vlans?The 4500 is the Active?There is a DHCP Pool for each of those Vlans on both gateways using "ip dhcp excluded-address" I ensured that the range of provided ips by each DHCP server will not be overlapped Obs.: Reducing the lease time, I ended with the calls bringing related problems.
 
OK, every thing is blue, every thing is fine.But the network diagram is realy complex(41 switchs, 89 uplinks), and depending of how is the network flow, one or other server answer first or latter.
 
For many reasons I would like that the secondary DHCP server would answer only if the primary DHCP server goes down.To me, the bigger reason is that DHCP database would be only in one DHCP server.But there is other reasons.
 
I passed by many frustrated solutions:Try to force a delay on the answer on one of the servers. - Impossible.Try to disable DHCP server, and, using EEM, enable it only if router became active in HSRP. - I couldn't do It.
 
What I'm thinking now is use the HSRP resource to resolve it.On both routers I would put a "ip helper-address" pointing to an Virtual_HSRP_IP.And depending on which router is the active, him will answer the request.
 
My first doubt is:Would it work?The second doubt is:Could I use the same Virtual_HSRP_IP that exists on that Vlan(see example 1),or I would need to point it to a Virtual_HSRP_IP in a different Vlan(see example 2)?

Example 1
        -----------------------------------
        |              4500               |
        -----------------------------------
        interface Vlan1
         ip address 10.10.0.2 255.255.0.0
         ip helper-address 10.10.0.1
         standby 1 ip 10.10.0.1

[code]....

View 3 Replies View Related

Cisco Switching/Routing :: ASA5505 - Setup Ethernet 0 / 6 To DMZ Connection?

Jun 12, 2012

My first time programming a Cisco ASA - Anyways I''m trying to setup up Ethernet 0/6 to be a DMZ Connection When I add port 0/6 to DMZ it gives me an error saying "The IP Address X.X.X.X /Subnet Mask cannot overlap the subnet of interface outside"So my question is I have an outside connection already configured - How can I make a DMZ connection with the same subnet mask with a different IP?

View 1 Replies View Related

Cisco Switching/Routing :: Upgrading A DS3 To Metro Ethernet / Gigabit Connection?

Jul 10, 2012

I have the possibility of upgrading a DS3 to Metro Ethernet, Gigabit connection. My dilemma is I have two VTP domains in my network. How can I get two VTP domains over one trunk to a remote site ?

View 0 Replies View Related

Cisco Routers :: RVS4000 / ISP WISP Point To Point Network Project?

Nov 30, 2012

Currently in place  ISP WISP Point to Point network would like some pointers to exceed in doing it right.  Here are some issues.ISP Fiber 50 Megs down and 50 Megs up  ( Working )What Router do I use? Looking at Cisco RVS4000 at JDT Site as main router I have routers at others towers using the 10.1.19.xxx address as wans setup.Do I pull out all routers and use only one from the JDT Site?

  a. Due to Port forwarding

  b. Lets say main Wan is 74.144.55.159 Lan 10.1.19.1 

1. Site BTT router is assign address 10.1.19.33 Lan 192.168.6.1

a. Can I setup 74.144.55.159:85 to see 10.1.19.33?

My Point ot Point radio use different IP address to separate from lan address (10.1.19.xxx)  Radios (10.1.119.xxx)1. Everything is working just want to re-design everything never thought I would grow this fast with in 2 years. Hope I explain this well enought.  90% of users are out in  the country without high speed internet.

View 1 Replies View Related

Cisco Wireless :: 1310 Point-to-point Bridge In Lightweight Mode?

Apr 24, 2011

how is the 1130 point-to-point bridge work in lighteight mode ?
 
Is this supported on 5508 and on new 2500 series controllers?
 
How does the WCS manage the point-to-point link?
 
I am aware that there is Lightweight software for the 1300 series bridges but never used one so far

View 6 Replies View Related

Cisco WAN :: VWIC3-1MFT-T1 / E1 / Point To Point Serial Link Configuration?

Jan 12, 2011

How do I configure a data T1 serial link on a router using IOS 15 and a VWIC3-1MFT-T1/E1 module. The "interface serialx/x/x" are not there anymore?

View 1 Replies View Related

Cisco Wireless :: Configure 1310 Point-to-point Bridge (AIR-BRI1310G-A-K9-R)

Apr 24, 2011

Configure 1310 point-to-point bridge (AIR-BRI1310G-A-K9-R)

View 3 Replies View Related

Cisco Firewall :: Terminate Point To Point Link Between 3750 And 6506?

May 20, 2012

I all we are going to terminate point to point link between 3750 and 6506. 
 
on 6506
 int gi1/45
no switchport access
ip address 192.X.0.x 255.255.255.0
no shut
 
[code]....
 
Does this config correct as i am configuring between stack switch and 6506

View 1 Replies View Related

Cisco WAN :: HWIC 4ESW Need To Configure Point To Point Data Dual Leased Lines

Jan 18, 2012

We have 1841 router with HWIC-4ESW we need to config point to point data Dual leased lines failover concept please find attached diagram.

View 3 Replies View Related

Cisco WAN :: Catalyst 6509 Switches Connected Directly Using Direct Point To Point Link

Apr 14, 2013

I have 2 Cisco Catalyst 6509 switches connected directly using direct point to point link.The OSPF is configured for point - point link.The currently the interface is down administratively.I will unshut the port . After that i would like to know how much time will it take for the ospf to establish the neighbour relation.

View 5 Replies View Related

Cisco Wireless :: AP1242G Point-to-Point Bridge Configuration?

Mar 16, 2013

I have two Cisco AP 1242G and i'm trying to configurate a Point-to-Point Bridge Configuration to connect two wired LAN. Figure 1.8 [URL] I would connect two wired networks.
 
I tryed two configurations: Root and Non-Root AP. This way every wired PC on the Root AP can connect to the Access points, but cannot connect to the wired PC on the Non-Root AP.AP and WGB. Even this way the wired computers on one AP cannot connect to the wired PC on the WGB. This way only the wireless client can connect to the wired network.  This is my network:

Root Bridge                                 Non Root Bridge
10.0.0.1                                      10.0.0.2
Wired clients on the RB                Wired clients on the Non RB
10.0.0.100                                   10.0.0.200

View 4 Replies View Related

Cisco WAN :: MWR2941 Qos Solution For 10mb Point-to-point L2 WAN Link

Jul 18, 2011

We have a MWR2941 (running 12.4(20)MR) router on site A and one in site B which will be connected over a Service provider L2VPN Ethernet over MPLS (EoMPLS) Network, with 10Mb Bandwidth allocated by the ISP. I have simulated this in the lab by directly connecting the two MWR's back-to-back via the Gig0/0 interface with configurable bandwidth of 10Mb on the Trunk interface.
 
The E1 TDM pseudowire end to end is working fine, with PTP configured for E1 timing/clocking. In addition I have a 2960-24PC-L switch connected on G0/2 of the MWR (on each end) configured with dot1q trunking. The switch will be used to connect two user groups in two seperate vlans (VlanA and vlanb) and transported across the same 10MB wan Link. Below are the requirements
 
1) Classify and mark Psuedowire packets E1-DATA coming from a E1/CEM interface and give it priority treatment over the WAN Link with reserved bandwidth of at least 4MB
2) Classify and mark Signalling/Timing PTP packets coming from PTP Vlan and give it strict bandwidth reservation over the WAN Link of 1MB
3) Classify and mark vlan A traffic coming from the 2960 Switch Trunk port (Connected to G0/2 on MWR) and give it bandwidth reservation over the WAN Link of 2MB
4) Classify and mark vlan B traffic coming from the 2960 Switch Trunk port (Connected to G0/2 on MWR) and give it bandwidth reservation over the WAN Link of 2MB
 
It is important that the E1 Traffic and the Signalling/Timing PTP packets are given priority and strict reservation so that it is not dropped in times of congestion. At the same time Vlan A and Vlan B need bandwidth reservation to give them their guaranteed bandwidth. 
 
Currently I have tried applying policy map to the CEM interface. However, I am having trouble matching anything on the CEM input. Also I am having trouble applying a service-policy outbound on the gig0/0 (WAN Link). Also I can’t apply a service-policy inbound on the Gig0/2 interface with match statement. I have tried configuring input policy map to classify and mark PTP traffic (Vlan 902), but the MWR does not also allow me to attach a service-policy to the vlan interface. how to configure the MWR and have a workable QOS solution.

View 2 Replies View Related

Cisco Wireless :: Aironet 1310G - Point To Point Bridge

Oct 14, 2012

Is any one can configure basic Point-toPoint wireless bridge. I need to connect two simple LAN with Cisco Aironet1310 AP. I required basic configuration with basic authentication between these two devices which is on IOS "123-8.JEA3".

View 16 Replies View Related

Cisco WAN :: 3845 / How To Configure Vrf For Point To Point Link

Mar 11, 2013

i have cisco 3845 router,how to configure vrf for point to point link .

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved