Cisco WAN :: HWIC 4ESW Need To Configure Point To Point Data Dual Leased Lines
Jan 18, 2012We have 1841 router with HWIC-4ESW we need to config point to point data Dual leased lines failover concept please find attached diagram.
View 3 Replies
ADVERTISEMENT
Cisco WAN :: Configure Newly Installed HWIC-4ESW On 2811 Router To Bridge To FE 0 / 0 Interface
Apr 20, 2012I am trying to configure a newly installed HWIC-4ESW on a 2811 router to bridge to the FE 0/0 interface. Currently, I have a cheap switch connected to FE 0/0 which in turn connects to all the phones, however now I just want to connect all the phones to the HWIC and have it internally bridge to FE0/0 for the connectivity to CME, etc.
View 5 Replies View RelatedTP-Link Dual-Band Wireless :: How To Configure N750 As Access Point
Dec 5, 2012Region : UnitedStatesModel : TL-WDR4300Hardware Version : V1Firmware Version : 3.13.23 Build 120810 Rel 44064nHow do I configure the TP-Link N750 wireless router model TL-WDR4300 as an access point so that computers/nodes on the WAN, LAN and wifi connections of this device are all on the same network/subnet?From the admin browser page, disabling DHCP and NAT does not provide the desired results.
View 10 Replies View RelatedCisco Wireless :: Configure 1310 Point-to-point Bridge (AIR-BRI1310G-A-K9-R)
Apr 24, 2011Configure 1310 point-to-point bridge (AIR-BRI1310G-A-K9-R)
View 3 Replies View RelatedCisco WAN :: 3845 / How To Configure Vrf For Point To Point Link
Mar 11, 2013i have cisco 3845 router,how to configure vrf for point to point link .
View 1 Replies View RelatedCisco Wireless :: 3502p - Access Point Support MESH And Point-to-Point Bridging?
Apr 16, 2013I need to know if 3502p with outdoor antennas supports Point-to-Point Wireless Bridging?
View 6 Replies View RelatedCisco Switching/Routing :: 2951 / 2 Leased Lines In LAN Network
Oct 24, 2011My current setup.
Layout:
Line01 Line02
| |
Cisco 2951 Cisco 2951
---------------------
|
Cisco 3750G - Server #1 & #2 for domain controller, sharepoint, etc
|
---------------------
| |
Cisco 2960 Cisco 2960
| | | | | | | ... | | | | |
workstation #1, #2, .... #70
And I would like to ask some opinion on the best configuration for the above layout:
1. Configuration #1 - Using load sharing and automatic failover So I want to ask whether there's any link/url that provides details/guides on how to setup the load sharing and failover?
2. Configuration #2 - Workstations 1 - 35 will be routed through Line01 gateway and workstations 36 - 70 will be routed through Line02 As for this configuration, it's done now. However, I want to know whether there's any software (preferred web based application which allows me to change the gateway from line #1 to line #2 for all 70 computers instead of having to go to each workstation to update the gateway).
Linksys Access Point :: Connect And Configure WAP54G Access Point To New Cable Modem?
Nov 1, 2012How do I connect and configure my WAP54G wireless access point to my new Cable Modem? I have it connected to the modem but I cannot access it to configure it. It appears to be working but before I got the cable modem I had it connected to a router and it was set-up with a static IP address. With my new ISP, I no longer have a static IP address so I am trying to configure the WAP54G to use DHCP. Trying to access it thru the internet at 192.168.1.245 does not work.
View 1 Replies View RelatedCisco Firewall :: 5505 - How To Apply Policing On ASAs With Leased Lines
Jul 2, 2012I'm trying to configure policing and/or shaping on a setup of 2 x ASA 5505 Sec Plus. The units are placed in office A and office B and each have a ISP connection to the internet and a leased line with a capacity of 4/4 Mbit/s for interoffice communication.
On each ASA there's four subnets. VLAN 200 is used to connect the offices through the leased line.
Subnets:
Outside = 2
Data = 10
Voice = 100
Linknet = 200
I've read a lot of articles and posts about shaping and policing on the ASA but still can't get it to work like I wan't to. I'm trying to limit all traffic besides IP-telephony traffic to 3 Mbit/s and thus reserving 900 Kbit/s for voice traffic. I tried setting a service-policy on the linknet interface on each ASA and set Traffic match to Any traffic and QoS settings for both input and output.
I can see traffic passing the policy when I run the "show service-policy police" command but it never seems to be high enough to be policed which is strange since the ASDM monitoring shows that I'm pushing 3900 kbit/s. I file transfers verifies that policing does'nt work.
Cisco Wireless :: Point To Point Access Point 1262 Bridging
Feb 27, 2013How would I bridge a wireless connection with a distance of 400 feet? Would twoAP1262N-A-K9 be able to make this happen? Or is there another wireless bridge that you all can think of?I would be connecting one AP1262 of off a 3750g switch and at the far end (400 ft aproximately) another AP1262N-A-K9.
View 12 Replies View RelatedLinksys Access Point :: Configure WRT120n As An Access Point?
May 1, 2012Is it possible to configure WRT120n as an access point?
View 1 Replies View RelatedSlap An HWIC - 4ESW Into A Router
May 9, 2012meaning slap an HWIC-4ESW into a router, say, an 1841, create an ether channel out of them to connect to my switch?
View 6 Replies View RelatedCisco WAN :: Hwic-4ESW 2 Unit On Chassis?
Mar 18, 2012i have some issue with Hwic-4ESW, if i install one card(Hwich-4ESW) is working all port then i install one more card ( Hwic-4ESW) it not working.interface and vlan is up but from my PC to port Hwic-4esw not working. what is problem on this ?
View 9 Replies View RelatedCisco WAN :: 2911 - Need PVDM When Use HWIC-2CE1T1-PRI For Leased Line
Oct 11, 2012We plan migrate an old existing WAN architecture based on legacy data serial links. These links will be consolidated on a E1 channalized card.
My question :
Is the HWIC-2CE1T1-PRI need a PDVM DSP ressources on router to oparate for data leased lines or no?
The VWIC3-1MFT-T1/E1 will be used for the backup dial in ISDN connexions? this type of cards a PVDM DSP ressources for data connexions or no?
ISR router are 2911.
Cisco WAN :: Can't Put A Second HWIC-4ESW In A 3825 Router And Don't Work
Aug 4, 2012I put a second HWIC-4ES in a 3825 router and it does not work, only work the first card that is inserted, I use the slot 0 for it, the 0/0 and 1/0 work with serial card only if I put the HWIC-4ESW in this slots the router does not work, only work in 0/2 and 0/3 but only one, I need to know if there is a command to active it because the data sheet in CISCO indicate that this model of router support 2 HWIC-4ESW. url...
View 1 Replies View RelatedCisco Switching/Routing :: HWIC 4ESW - Cannot Ping It
Dec 28, 2011I have a 2811 ISR, a lab unit with almost nothing yet configured other than some IP networks on serial and FE interfaces to ping to other lab routers. And I have one HWIC-4ESW installed, and I amrunning IOS 15.2.I want to set the card as a single routable interface and just have the ports act like switch ports, which I imagine is the default design of these cardsI work a lot with Cisco 891 ISRs so figured it's the same here, assign an IP to interface Vlan1 and all is well. That was wrong, obviously more config is required.It seems there are a lot of differing answers out there, so far none what worked for me. The best looking one I could find said to assign an IP to the Vlan 1 interface, then go to each of the four FE interfaces on the switch module.
View 3 Replies View RelatedCisco WAN :: Not Able To See HSRP Configuration Option For HWIC-4ESW
Jun 12, 2013I have 3945 router using the HWIC-4ESW module.I am not able to see the HSRP configuration commands under these interface.Does this module support HSRP ? If yes , do i need upgrade the IOS of router.
View 1 Replies View RelatedCisco WAN :: 2811 WAN Link Terminated In HWIC-4ESW
Jun 3, 2013I have a module of HWIC-4ESW installed into Cisco 2811 router where 3 WAN link is terminited. Suddently WAN links stopped working from last night. I have performed shutdown and no shutdown in the interface but still the the WAN link was not working. After performing a reboot the WAN link started working. No error logs were generated while the WAN link was down.
View 4 Replies View RelatedCisco Infrastructure :: Use HWIC-4ESW As No Switch Port?
Oct 4, 2012Can We use Cisco HWIC-4ESW as no Switch Port.
View 5 Replies View RelatedCisco Switching/Routing :: Making Etherchannel On A 4ESW HWIC
Nov 4, 2012Maybe this was listed in the release notes for the product and I missed it, but can this item support Etherchannel in a 2801 router? I installed the module into the router and the router recognizes the module. I can configure the ports as access or trunk ports, but I am unable to configure the channel-protocol or the channel-group for the Etherchannel. The IOS on the router is 15.1 M with the upgraded Bootloader version 12.3.
View 1 Replies View RelatedCisco Infrastructure :: Connect Two Router With One HWIC-4ESW Card?
Sep 2, 2011How Can I connect two router with one HWIC-4ESW card , I have Problem with this because when I tried to do , I received the message I can´t configure IP address on L2. The idea is to connect two routers with /30.
View 2 Replies View RelatedCisco WAN :: Apply MQC On 4 Port HWIC-4ESW - 3845 Router?
Mar 24, 2011I have 3845 Router with HWIC-4ESW & I am trying to apply MQC on SVI interface but I keep getting configuration Error!-RTR(config-if)#service-policy output XYZ_WAN_QOS Configuration failed I believe that HWIC-4ESW is Layer 2 port & you can not apply Module Qos on SVI interface. I am exploring other option.
I have following link for 1 OR 2 Port Fast Ethernet port but not sure whether this will support what I am looking for.[URL] Aslo I have HWIC-1GE-SFP card on Same router where MQC works fine .interface GigabitEthernet0/1 description METRO-E duplex auto speed auto media-type rj45 service-policy output Metro-E?
Cisco Switching/Routing :: Trunking With HWIC-4ESW On 1921?
Feb 27, 2012We have been facing a problem at my company ! We have a Cisco Router 1921 with one HWIC-4ESW in trunking with a RuggedCom switch RSG2100.When I use the GigabitEthernet port to make a trunk, I create 2 sub-interfaces (one for each Vlan) and configure the Port on Switch as Trunk, the inter-VLan routing works with no problem.But now I need to use this configuration using the HWIC-4ESW on Router, and I can't do this work. I try creat interface Vlan for each vlan, and try creating the VLans at Router Vlans database, but no way. At router I enter in interface and try to do the switchport trunk command to add a Vlan, but doesn't work.
View 4 Replies View RelatedCisco Switching/Routing :: 1921-SEC/K9 - HWIC-4ESW Compatibility
Jan 9, 2012Does Cisco 1921-SEC/K9 support HWIC-4ESW ? I require 4 x 10/100 Ethernet ports
If yes how many ? are there any drawbacks if i use this module instead of a switch?
Cisco Switching/Routing :: Two Cards HWIC-4ESW On C3845?
Nov 18, 2012We have two cards HWIC-4ESW on router 3845 but we need that the two cards 8 ports conected betwen, if a pc on port 1 can ping a pc conected on port 8 on second card. tis comunication can,t doing a pc on port 1 can,t conected a pc on port 8.
the configuration is the folowing
interface FastEthernet0/0/0
switchport access vlan 100
speed 100
[Code].....
Cisco WAN :: Test A MPLS Capability With1841 Router And HWIC-4ESW
Oct 11, 2012We are planning on moving towards MPLS. I want to test a MPLS capability with Cisco 1841 Router and a HWIC-4ESW. Is it possible to use the MPLS withe mentioned devices?
View 1 Replies View RelatedCisco Wireless :: 2602 -Access Point Getting Power But Not Data
Apr 21, 2013I have a problem, where we are installing a Cisco 2602 access piont, the AP is getting power as the lights are on (changing colors Green, White, Red). In the switch side the LED for the interface is blinking green only when I chosse PoE. Also I cannot see the AP in CDP neighbours.
It seems to be a physical problem but the cable is tested and showing connected for all pairs and parallal (straight) connection.
Access Point was connected directly to the same interface (I mean with a patch cable to the switch) and working
Linksys Access Point :: WAP200 Is Sending Out STP Data Every 2 Seconds
Apr 18, 2008We've got a network consisting out of Cisco 3750 and 2960 units on which STP is enabled. We are trying to get a WAP200 working in this environment. Problem is that the WAP200 is sending out STP data every 2 seconds (checked with Wireshark) wich is causing mayhem on the network. The situation will not settle down to a stable situation.Question:Is there any way in which the STP traffic generated by the WAP200 can be disabled ?
View 2 Replies View RelatedUsing A Dual - Band Router As An Access Point?
Mar 29, 2011I'm networking a clients home and he specifically wants dual-band wifi through-out. Now he has a fairly large 3 story house, and wanted to place an access point on the top floor to be assured he'll have strong and reliable signal. He's going to have multiple TV's wired into the network, as well as computers, laptops, phones, a Xbox 360 and a PS3. Were using Gigabit switches and a D-link Simultaneous Dual-band Gigabit router.The modem, router, and main 16 port switch will be in his basement in a semi-server room. He currently has 12 lines run throughout his house, 3 to the top floor, 5 to the main floor, and the ability to lay some in the basement if he needs. The 16port switch will plug into the router, I'm also putting an 8 port into the router from the main and top floor. The remaining lines will plug into the switch in the basement. On the top floor I was going to install an AP or Router turned into an AP into the 8port switch.Now the only reason I am considering using a router instead of just getting an AP, is that neither of us can find a simultaneous Dual-band AP. It seems the only simultaneous DB out there is in routers. So, my question is, will I be able to easily use a router as an AP AND get simultaneous Dual-band out of it if I do so? Is there a Simultaneous Dual-band AP on the market that would a better investment?
View 1 Replies View RelatedCisco VPN :: ASA5510 - Termination Point With Dual ISP Connection
Nov 2, 2011We have an ASA 5510 with ~100 vpn lan2lan. Now we need to migrate to a new ISP, so we have connected a new asa interface to the internet. Default gw is still on old connection. We are trying to migrate vpn lan2lan using static routes, pointing ip of remote vpn gateway to new isp gateway. VPNs going up, but when they try to send traffic, I can see Rx counter growing up, but Tx remains 0.. I've tried with different vpn (old and completely new), and problem remains.
View 1 Replies View RelatedCisco Wireless :: Access Point 2602e Antennas Dual Band
Apr 9, 2013I am currently looking for informations about access point 2602e, more precisly about antennas.This AP have four RTNC connectors for external antennas, but I found these table into Cisco documentation: [code] When I see that, I understand that we only need, to transmit, three antennas with 2,4 Ghz (which is the only band we will use in a first time), but four with 5 Ghz.I also found these informations, in the same documentation:The 2602E models are configured with up to four external dual-band dipole antennas, and two 2.4-GHz/5-GHz dual-band radios. The radios and antennas support frequency bands 2400–2500 MHz and 5150–5850 MHz through a common dual-band RF interface. Features of the external dual-band dipole antennas are:
• Four RTNC antenna connectors on the top of the access point
• Three TX and four RX antennas
My question: with four antennas, we have three TX and four RX, is it for 2,4 Ghz, 5 Ghz or both?
Cisco Switching/Routing :: 1941 / K9 VPN Router MPLS IPVPN Point-to-point
Mar 15, 2012I have 2 cisco 1941/K9 vpn router. I have configured both with LAN ip address given by our vpn provider which is 172.10.10.1 and the other is 172.10.20.1. Both IP addresses are configured to GigabitEthernet port 0/0 on both routers.
1. Is it possible to configure our own set of ip address like 10.71.10.1 and 10.71.50.1 on the GE 0/0 port?
2. Or can we configure our own set of ip addresses (10.71.10.1 and 10.71.50.1) to GigabitEthernet port 0/1 and maintain the other ip addresses on port 0/0?
The first purpose is to have our own set of ip addresses for LAN connection and I will be able to connect or telnet whichever ip address or port is up.
Cisco Routers :: RVS4000 / ISP WISP Point To Point Network Project?
Nov 30, 2012Currently in place ISP WISP Point to Point network would like some pointers to exceed in doing it right. Here are some issues.ISP Fiber 50 Megs down and 50 Megs up ( Working )What Router do I use? Looking at Cisco RVS4000 at JDT Site as main router I have routers at others towers using the 10.1.19.xxx address as wans setup.Do I pull out all routers and use only one from the JDT Site?
a. Due to Port forwarding
b. Lets say main Wan is 74.144.55.159 Lan 10.1.19.1
1. Site BTT router is assign address 10.1.19.33 Lan 192.168.6.1
a. Can I setup 74.144.55.159:85 to see 10.1.19.33?
My Point ot Point radio use different IP address to separate from lan address (10.1.19.xxx) Radios (10.1.119.xxx)1. Everything is working just want to re-design everything never thought I would grow this fast with in 2 years. Hope I explain this well enought. 90% of users are out in the country without high speed internet.
