i have some issue with Hwic-4ESW, if i install one card(Hwich-4ESW) is working all port then i install one more card ( Hwic-4ESW) it not working.interface and vlan is up but from my PC to port Hwic-4esw not working. what is problem on this ?
View 9 Repliesmeaning slap an HWIC-4ESW into a router, say, an 1841, create an ether channel out of them to connect to my switch?
View 6 Replies View RelatedI put a second HWIC-4ES in a 3825 router and it does not work, only work the first card that is inserted, I use the slot 0 for it, the 0/0 and 1/0 work with serial card only if I put the HWIC-4ESW in this slots the router does not work, only work in 0/2 and 0/3 but only one, I need to know if there is a command to active it because the data sheet in CISCO indicate that this model of router support 2 HWIC-4ESW. url...
View 1 Replies View RelatedI have a 2811 ISR, a lab unit with almost nothing yet configured other than some IP networks on serial and FE interfaces to ping to other lab routers. And I have one HWIC-4ESW installed, and I amrunning IOS 15.2.I want to set the card as a single routable interface and just have the ports act like switch ports, which I imagine is the default design of these cardsI work a lot with Cisco 891 ISRs so figured it's the same here, assign an IP to interface Vlan1 and all is well. That was wrong, obviously more config is required.It seems there are a lot of differing answers out there, so far none what worked for me. The best looking one I could find said to assign an IP to the Vlan 1 interface, then go to each of the four FE interfaces on the switch module.
View 3 Replies View RelatedI have 3945 router using the HWIC-4ESW module.I am not able to see the HSRP configuration commands under these interface.Does this module support HSRP ? If yes , do i need upgrade the IOS of router.
View 1 Replies View RelatedI have a module of HWIC-4ESW installed into Cisco 2811 router where 3 WAN link is terminited. Suddently WAN links stopped working from last night. I have performed shutdown and no shutdown in the interface but still the the WAN link was not working. After performing a reboot the WAN link started working. No error logs were generated while the WAN link was down.
View 4 Replies View RelatedCan We use Cisco HWIC-4ESW as no Switch Port.
View 5 Replies View RelatedMaybe this was listed in the release notes for the product and I missed it, but can this item support Etherchannel in a 2801 router? I installed the module into the router and the router recognizes the module. I can configure the ports as access or trunk ports, but I am unable to configure the channel-protocol or the channel-group for the Etherchannel. The IOS on the router is 15.1 M with the upgraded Bootloader version 12.3.
View 1 Replies View RelatedHow Can I connect two router with one HWIC-4ESW card , I have Problem with this because when I tried to do , I received the message I can´t configure IP address on L2. The idea is to connect two routers with /30.
View 2 Replies View RelatedI have 3845 Router with HWIC-4ESW & I am trying to apply MQC on SVI interface but I keep getting configuration Error!-RTR(config-if)#service-policy output XYZ_WAN_QOS Configuration failed I believe that HWIC-4ESW is Layer 2 port & you can not apply Module Qos on SVI interface. I am exploring other option.
I have following link for 1 OR 2 Port Fast Ethernet port but not sure whether this will support what I am looking for.[URL] Aslo I have HWIC-1GE-SFP card on Same router where MQC works fine .interface GigabitEthernet0/1 description METRO-E duplex auto speed auto media-type rj45 service-policy output Metro-E?
We have been facing a problem at my company ! We have a Cisco Router 1921 with one HWIC-4ESW in trunking with a RuggedCom switch RSG2100.When I use the GigabitEthernet port to make a trunk, I create 2 sub-interfaces (one for each Vlan) and configure the Port on Switch as Trunk, the inter-VLan routing works with no problem.But now I need to use this configuration using the HWIC-4ESW on Router, and I can't do this work. I try creat interface Vlan for each vlan, and try creating the VLans at Router Vlans database, but no way. At router I enter in interface and try to do the switchport trunk command to add a Vlan, but doesn't work.
View 4 Replies View RelatedDoes Cisco 1921-SEC/K9 support HWIC-4ESW ? I require 4 x 10/100 Ethernet ports
If yes how many ? are there any drawbacks if i use this module instead of a switch?
We have two cards HWIC-4ESW on router 3845 but we need that the two cards 8 ports conected betwen, if a pc on port 1 can ping a pc conected on port 8 on second card. tis comunication can,t doing a pc on port 1 can,t conected a pc on port 8.
the configuration is the folowing
interface FastEthernet0/0/0
switchport access vlan 100
speed 100
[Code].....
We are planning on moving towards MPLS. I want to test a MPLS capability with Cisco 1841 Router and a HWIC-4ESW. Is it possible to use the MPLS withe mentioned devices?
View 1 Replies View RelatedI am trying to configure a newly installed HWIC-4ESW on a 2811 router to bridge to the FE 0/0 interface. Currently, I have a cheap switch connected to FE 0/0 which in turn connects to all the phones, however now I just want to connect all the phones to the HWIC and have it internally bridge to FE0/0 for the connectivity to CME, etc.
View 5 Replies View RelatedI just installed two of the HWIC-1GE-SFP cards in the CISCO3945 router but they are not recognized... I don't see any messages on the console output. I don't see them in the "show diag" command. I don't see new ports in the "show run" either... Is there some command I need to put in to activate them? Here is show version of my router:
Cisco IOS Software, C3900 Software (C3900-UNIVERSALK9-M), Version 15.0(1)M4, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
[Code]....
We have 1841 router with HWIC-4ESW we need to config point to point data Dual leased lines failover concept please find attached diagram.
View 3 Replies View Relatedwe need to install a line cards (WS-X4548-GB-RJ45, chassis WS-C4510R-E), on a chassis Ws-6504-E.where I can find information about compatibility?
View 2 Replies View RelatedWhat is the difference between HWIC-1ADSL-M and HWIC-1ADSL without the "-M"?Can either of the above ADSL cards be used in Cisco 3845 router? We are using HWIC-1ADSL-M in our Cisco 3845 routers everywhere?
View 1 Replies View RelatedWhat are different Wic-1FE Vs Wic-4ESW?
View 6 Replies View RelatedWhat are different Wic-1FE Vs Wic-4ESW?
View 1 Replies View Relatedi was just wondering if its possible to use a WIC-4ESW with a 2611 non-XM router?
with any IOS versions, i just want to know if its possibly or not.
Got a question regarding this wic-4esw card the router knows it's there from show inventory and the Ethernet interfaces are showing up, but I'm not getting devices to connect that is the pc plugged into the Ethernet on the switch card are not getting address from the routers dhcp.At present I do not have vlan1 set up as I use an ip address going to eth0 which is plugged into a 3524 switch which I want to get rid off because it's too loud.So do I need to get rid of the ip on the router Ethernet 0 and do vlan 1 with an ip address for the router to fully understand the switch card and host pcs and phones to be able to have address distributed to these devices.
View 4 Replies View RelatedI started to set up a 1721 router with WIC-4ESW. This is on an internal network, so only looking to just do routing from FA/0's interface to the networks attached to ports on the WIC. I first assigned just VLANs to 2 of the ports and this did not work. So I did some reading up and decided to use bridge groups. Except I still can not access the interfaces on the WIC. And by that I mean on the router itself I can not ping the ip assigned to the BVI.
I have another 1721 w/4 port that long ago I seem to remember simply assigning VLANs to the interfaces and I was able to communicate between the networks without issue (or maybe I just don't rememer that well). Thing is I should be able to at least ping the internal interfaces shouldn't I (assuming the status is up). I don't know why BVI2 and 3 are listed as down, nor do I seem to know how to bring these up.
This is what ip int br gives me:
1721#sh ip int br
Interface IP-Address OK? Method Status Protocol
BVI2 192.168.101.1 YES manual down down
[Code]....
We have cisco 2911/k9 we fixed 2 HWIC-4ESW crds in 2911. I create 4 vlan i have assigned 1 HWIC-4ESW all vlans are working fine
when i configure 5 th vlan it assigned second HWIC-4ESW 1 port but interface status showing up. i connected one system to that port i try
to ping that port that port notable to pinging is there any activation for that second HWIC-4ESW.
Any configuration guide for EHWIC-4ESW card. Also the difference in configuration between EHWIC-4ESWG and HWIC-4ESW if any?
View 1 Replies View RelatedI was looking for Rack Unit required for 7206 VXR & 3945E but couldn't find it.
View 1 Replies View RelatedCan I create lag betwen stack unit to increase speed between units ?? stack connection is only 1Gbit on ports 24/48 if posible lag link must be in trunk mode ?
View 4 Replies View Related3502i's LED light turn white? Ifso, what does it mean? The info on the LED lights does not mention white. The serial port and the data port are non responsive, but the unit stays powered over PoE.
View 22 Replies View RelatedNow i plan to order Wireless Cisco model : AIR-AP1242AG-A-K9 around 40 unit but i don't know to manage all AP becuase it has alot of AP,
View 9 Replies View RelatedI have some technical consultations that I would like to know which would be a better implementation.
I am seeking for clarifications whether putting VPN and firewall in a single software or separating both into separate software.
We've have a 2 SGE2010-48 port, stacked. 4 LAGS are denifed, two on primary, whitch are working, two on slave unit are NOT working. Devices connected to LAGS are de the same and same configuration (Cisco ASA 5510).
View 3 Replies View RelatedMonday, I had a cisco 1750 router in place suddenly stop communicating to a Larscom ISP owned unit. Since then I have sent two replacement 1721 routers with WIC-1ENET cards. I have used the original straight thru cable to connect the 10baset port on the Larscom to my E0 on the WIC-1ENET. No link lights on either. I have also tried a known working straight thru cable and a crossover cable. No link lights.
I can take a crossover cable from a pc and ping the E0 port without issue. The ISP is telling me it is an issue with my equipment.