Cisco Switching/Routing :: Any Configuration Guide For EHWIC-4ESW Card
Jul 18, 2012Any configuration guide for EHWIC-4ESW card. Also the difference in configuration between EHWIC-4ESWG and HWIC-4ESW if any?
View 1 Replies
ADVERTISEMENT
Cisco Switching/Routing :: Configuration EHWIC-3G-HSPA-U Card On 2911
Nov 15, 2012How I configurate EHWIC-3G-HSPA+7 card on 2911.
View 3 Replies View RelatedCisco Switching/Routing :: Enabling EHWIC Card Into 2911?
Feb 16, 2012I have installed a EHWIC-4ESG card into my 2911 router running IOS Ver 15.1(4)M2. When I do a show diag, I can see the card, but I get the following line "Could not get card instance pa_bay=0 slot=0." Am I missing a step, do I have change something, is it not compatible (all that I have read, states that is)
View 3 Replies View RelatedCisco Switching/Routing :: 2811 And EHWIC VA DSLA Connection Configuration
Jan 22, 2012I am having trouble setting up a EHWIC-VA-DSL-A= card on my cisco 2811 running the following the following:c2800nm-adventerprosek9-mz.151-4.M2.bin and C2800NM_RM2.srec.124-13r.T11
My hardware supplier tells me its the right adsl card (have 1 existing working card not the same) but the card will not detect on the system to be configured.is this the right card? am I missing something?
Cisco WAN :: 1751v With Wic-4esw Switch Card
Sep 8, 2011Got a question regarding this wic-4esw card the router knows it's there from show inventory and the Ethernet interfaces are showing up, but I'm not getting devices to connect that is the pc plugged into the Ethernet on the switch card are not getting address from the routers dhcp.At present I do not have vlan1 set up as I use an ip address going to eth0 which is plugged into a 3524 switch which I want to get rid off because it's too loud.So do I need to get rid of the ip on the router Ethernet 0 and do vlan 1 with an ip address for the router to fully understand the switch card and host pcs and phones to be able to have address distributed to these devices.
View 4 Replies View RelatedCisco WAN :: 2921 Router Not Detecting EHWIC-1GE-SFP-CU Card
Oct 2, 2011I just got a brand new Cisco 2951 router that has built-in 3 gigabit interfaces cards. We want to add additonal 2 GE EHWIC-1GE-SFP-CU card to it. When it booted up and type show inventory, it did not detect the presence of the card. There was light on at the back of it. I have checked the compatibility on Cisco. The card is compatible with this router. Do we have to install the card with special instructions in order for the router to see it?
View 1 Replies View RelatedCisco Wireless :: High CPU On 2921 With EHWIC Card?
Aug 16, 2012I am getting the following error message on a Cisco 2921 as a result of which has a there is 99 % CPU util. This router has the following cards installed and 4G WWAN EHWIC is running 15.1(4) M3 image.
EHWIC_CELL_MSG-1-EHWIC_ERROR_EVENTS: eHWIC Error Event: TxCLK PLL lost lock, HWIC slot 3
Cisco WAN :: 2911 - Installing 4G Wireless Card (EHWIC-4G-LTE-V)
Mar 27, 2013We're installing a 4G wireless card (EHWIC-4G-LTE-V) in our 2911 for the first time. Upon boot-up, the IOS doesn't recognize the card (the "show inv" command doesn't list it at all). Do I need to give a command or have a certain IOS version in order for it to be recognized?
View 1 Replies View RelatedCisco WAN :: 1841 Basic ADSL Configuration Guide
Aug 5, 2012I am trying to configure a Cisco 1841 to allow the users to access the internet. This is my first step with ppp. All the rest of the configuration is ok but I don't know how to setup the interfaces Dialer0 and ATM0/0/0.
Need very basic configuration that I can analyze and use on my device?
Cisco Infrastructure :: Connect Two Router With One HWIC-4ESW Card?
Sep 2, 2011How Can I connect two router with one HWIC-4ESW card , I have Problem with this because when I tried to do , I received the message I can´t configure IP address on L2. The idea is to connect two routers with /30.
View 2 Replies View RelatedCisco Switching/Routing :: HWIC 4ESW - Cannot Ping It
Dec 28, 2011I have a 2811 ISR, a lab unit with almost nothing yet configured other than some IP networks on serial and FE interfaces to ping to other lab routers. And I have one HWIC-4ESW installed, and I amrunning IOS 15.2.I want to set the card as a single routable interface and just have the ports act like switch ports, which I imagine is the default design of these cardsI work a lot with Cisco 891 ISRs so figured it's the same here, assign an IP to interface Vlan1 and all is well. That was wrong, obviously more config is required.It seems there are a lot of differing answers out there, so far none what worked for me. The best looking one I could find said to assign an IP to the Vlan 1 interface, then go to each of the four FE interfaces on the switch module.
View 3 Replies View RelatedCisco Switching/Routing :: 1721 WIC-4ESW Cannot Get BVI To Work
Mar 11, 2012I started to set up a 1721 router with WIC-4ESW. This is on an internal network, so only looking to just do routing from FA/0's interface to the networks attached to ports on the WIC. I first assigned just VLANs to 2 of the ports and this did not work. So I did some reading up and decided to use bridge groups. Except I still can not access the interfaces on the WIC. And by that I mean on the router itself I can not ping the ip assigned to the BVI.
I have another 1721 w/4 port that long ago I seem to remember simply assigning VLANs to the interfaces and I was able to communicate between the networks without issue (or maybe I just don't rememer that well). Thing is I should be able to at least ping the internal interfaces shouldn't I (assuming the status is up). I don't know why BVI2 and 3 are listed as down, nor do I seem to know how to bring these up.
This is what ip int br gives me:
1721#sh ip int br
Interface IP-Address OK? Method Status Protocol
BVI2 192.168.101.1 YES manual down down
[Code]....
Cisco Wireless :: C881W-A-K9 Configuration Guide And Facing Restart
Mar 5, 2013I have Cisco C881W-A-K9 wireless ruter that i want to configure with one SSID hiwever i am not able to achieve this . [code]
View 1 Replies View RelatedCisco Switching/Routing :: Making Etherchannel On A 4ESW HWIC
Nov 4, 2012Maybe this was listed in the release notes for the product and I missed it, but can this item support Etherchannel in a 2801 router? I installed the module into the router and the router recognizes the module. I can configure the ports as access or trunk ports, but I am unable to configure the channel-protocol or the channel-group for the Etherchannel. The IOS on the router is 15.1 M with the upgraded Bootloader version 12.3.
View 1 Replies View RelatedCisco Switching/Routing :: Trunking With HWIC-4ESW On 1921?
Feb 27, 2012We have been facing a problem at my company ! We have a Cisco Router 1921 with one HWIC-4ESW in trunking with a RuggedCom switch RSG2100.When I use the GigabitEthernet port to make a trunk, I create 2 sub-interfaces (one for each Vlan) and configure the Port on Switch as Trunk, the inter-VLan routing works with no problem.But now I need to use this configuration using the HWIC-4ESW on Router, and I can't do this work. I try creat interface Vlan for each vlan, and try creating the VLans at Router Vlans database, but no way. At router I enter in interface and try to do the switchport trunk command to add a Vlan, but doesn't work.
View 4 Replies View RelatedCisco Switching/Routing :: 1921-SEC/K9 - HWIC-4ESW Compatibility
Jan 9, 2012Does Cisco 1921-SEC/K9 support HWIC-4ESW ? I require 4 x 10/100 Ethernet ports
If yes how many ? are there any drawbacks if i use this module instead of a switch?
Cisco Switching/Routing :: Inserting 2 ZHWIC 4ESW In 2911/K9
Jul 8, 2012We have cisco 2911/k9 we fixed 2 HWIC-4ESW crds in 2911. I create 4 vlan i have assigned 1 HWIC-4ESW all vlans are working fine
when i configure 5 th vlan it assigned second HWIC-4ESW 1 port but interface status showing up. i connected one system to that port i try
to ping that port that port notable to pinging is there any activation for that second HWIC-4ESW.
Cisco Switching/Routing :: Two Cards HWIC-4ESW On C3845?
Nov 18, 2012We have two cards HWIC-4ESW on router 3845 but we need that the two cards 8 ports conected betwen, if a pc on port 1 can ping a pc conected on port 8 on second card. tis comunication can,t doing a pc on port 1 can,t conected a pc on port 8.
the configuration is the folowing
interface FastEthernet0/0/0
switchport access vlan 100
speed 100
[Code].....
Cisco Switching/Routing :: EHWIC-1GE-SFP-CU MPLS Labeled Packets Are Not Being Processed
Dec 27, 2011We have the problem that MPLS labeled packets are not being processed on EHWIC-1GE-SFP-CU if L3PDU + Shim-Header exceeds 1500 bytes.When we move the config exactly to the on-board Interface Gi0/0 it works with put any problems. [code]
View 1 Replies View RelatedCisco WAN :: Not Able To See HSRP Configuration Option For HWIC-4ESW
Jun 12, 2013I have 3945 router using the HWIC-4ESW module.I am not able to see the HSRP configuration commands under these interface.Does this module support HSRP ? If yes , do i need upgrade the IOS of router.
View 1 Replies View RelatedCisco Switching/Routing :: Configuring 1941 With 8 Port EHWic Switch Module And Onboard GE Ports In Single LAN?
Jul 1, 2012Can you configure a Cisco 1941 to use an 8 port EHWic module and the 2 onboard GE ports in a single LAN?
I've discovered you can't have the on GE ports associated with a VLan, and I'm when I've previously researched for a solution, bridging was mentioned but I cannot seem to get it to work (or completely understand it)The reason I would like to use all 10 ports on for the LAN is becuase I have 10 devices I need to connect to the 1941?
Cisco WAN :: Can't Use Ehwic-3g-hspa-u Card In 2800 Series And 1841 Series Router
Jun 2, 2012why I can't use cisco ehwic-3g-hspa-u card in cisco 2800 series and 1841 series router?documentation said that it should work with that devices but when I installed it, it doesn't work even as device i can't see I am using cisco latest ios advance ent. 15.1(4)M4?
View 3 Replies View RelatedCisco Switching/Routing :: 6509 Convert CatOS Configuration To Native IOS Configuration
Jul 17, 2012I am position to migrate from CatOS 6509 switch to native IOS 6509 switch. long time ago, there was some site to convert automatically based on copy and paste onto the tool, but i can not find.
Does anybody know how to convert CatOS configuration to Native IOS configuration ? It is not IOS change, but it is configuration convert.
Cisco Switching/Routing :: Using SD Card Slot On ME3600X
Mar 13, 2013we are trying to use the SD Card Slot on an Cisco ME3600X (ME-3600X-24FS-M) IOS Version 15.2(4)S2. If i try to copy a file from the sd card slot to the flash there is no Option like "slot0:" or something alse and no syslog message appers while adding the SD Card.
View 5 Replies View RelatedCisco Switching/Routing :: 2801 - Get IOS On Flash Card?
Mar 15, 2012I have this 2801 in a critical environment. We had a brief power blip, and even though the router is on UPS, something happened. Anyway, after working with TAC, they determined the flash card had gone corrupt. Lucky for me I had a spare 2801 in my office, I grabbed that flash card and plugged it in and we're back up and going.
TAC sent me a new flash card. No matter what I do, I cannot get IOS to load on this thing! I am stuck in rommon. Here's what I've tried:
tftpdnld in rommon, times out. using another 2801 as a tftp-server. doesn't complete. using xmodem. ugh. never seems to get started. booting the router with a known good flash card, so I can get to ena, and "copy tftp flash".
have used tftpd32, Solar Winds TFTP server, What's Up Gold TFTP server, and open source tftp from sourceforge. With the tftp32, it always gets to exactly 73% download and then times out (it says, I have a feeling it's noty really a timeout). I have tried having the router and tftp server the only devices on a switch, i have tried the router plugged directly into the tftp server with a cross connect cable. No happiness. The open source tftp server reported (and I have to paraphrase, I am not near the router) "client does not support block number recount" or something like that. The client being the 2801.
The iOS file is about 45M. Someone asked me if the flash card was formatted...would that matter? would the tftp even start if it wasn't?
OK, I've gone on long enough. TAC is dispatching a new card AND 2801!
Cisco Switching/Routing :: EHWIC4ESG Card Into 1941
Apr 4, 2013Recently my company buy a EHWIC4ESG card and put into the cisco 1941. The reason we buy this card is because the in built two network ports of cisco 1941 are being used up. g0/1 is being connected to the internet and g0/0 is being connected to the office switch (192.168.5.x)
We have two servers (192.168.6.x and 158.55.33.x) that required to be connected to this router 1941 where the router will be configured as VPN for external user to access this server.
The EHWIC4ESG card is put into the router 1941 and after typing the "running-config" command, i could see it create a vlan 1 interface and
interface GigabitEthernet0/1/0
interface GigabitEthernet0/1/1
interface GigabitEthernet0/1/2
interface GigabitEthernet0/1/3
[Code]...
Cisco Switching/Routing :: To Find Out The Serial No For Cip Card 7500
Feb 8, 2012How do we find out the serial no. for a CIP card on a cisco 7500 router.
View 1 Replies View RelatedCisco Switching/Routing :: 3725 - Format CF Card On 1841
Dec 26, 2011I have 3725 router with internal CF and external slot for CF. I tried upgrading and ended up deleting the iOS version on the internal flash, and can not now put the iOS back!! I turned it off.... so there was no active iOS..
I have tried formatting the CF card on an 1841 but the 3725 won't read it. It is obviously stuck at ROMMON
What is the correct way to format a CF card so my 3725 will read it and I can get an iOS back on it!!
Cisco Switching / Routing :: 16 / 24 Port Ethernet Card For 2800?
Jan 11, 2012I am looking a 16 or 24 Port Ethernet (NON POE) card for my 2800 Cisco Router NM-16ESW is EOL/EOS and the replacement is shown as SM-ES2-24 However SM-ES2-24 is not supported on Cisco 2800 Series.
View 2 Replies View RelatedCisco Switching/Routing :: Reading 4/port Card Of 1811
Aug 30, 2012I have a Cisco 1811 with a 4/port Serial Async/Sync (HWIC 4 A/S) and another 2 port A/S serial wic. My router seems to have a problem reading the 4/port card. I did some research and it looks like there shouldn't be a compatibility issue.
View 7 Replies View RelatedCisco Switching/Routing :: Nexus 5k With L3 Card Showed Offline?
Aug 30, 2011i have a nexus 5k with a l3 card i'm not able to bring online
NX-OS is:5.0(3)N2 (1)
L3 card is:L55D160L3
i inserted L3 module several time with the same resul...if i perform a show module i see the card offline. At the boot switch show an error message:
L3 module is down due to a BTCM down..
Cisco Switching/Routing :: To Replace A Line Card WS-X6748-SFP
Oct 18, 2012I urgently want to replace a faulty line card WS-X6748-SFP with a new one. The switch concern is a 5609-V-E operating in Virtual Switching System mode.How long do you suggest the down time will be?
View 1 Replies View RelatedCisco Switching/Routing :: High Density Card For 6500E And 2T SUP
Jun 5, 2012I have a customer that in the past has been using 6506E chassis with Sup32 and the WS-X6196-21AF cards for their closet.With the End of Sale of this combination and the announced End of Sale of the Sup720-3B announced, this kind of pushes the configuration to a Sup 2T.BUT the SUP 2T does not support these low speed high density cards.
Is there a card coming that will address need? Customer generally has had dual sup32's and 3 to 4 cards of the 96port AF.They stock spares besides haveing smartnet on the boxes or moving to a different platform like the 4510R+ or stacks of switches will mess them up.
