we are trying to use the SD Card Slot on an Cisco ME3600X (ME-3600X-24FS-M) IOS Version 15.2(4)S2. If i try to copy a file from the sd card slot to the flash there is no Option like "slot0:" or something alse and no syslog message appers while adding the SD Card.
View 5 RepliesStruggling to find any documentation that states both "ip accounting & netflow" are supported on the new ME3600 switches. I have tried both a 12 and 15 release of software. Netflow produces no data what so ever, ip accounting only produces data (of the global network) when configured on my uplink (running MP-BGP network) unable to get specific data for user networks in seperate VRFs. Is this a case of the commands being there but not being supported?
View 0 Replies View RelatedI'm looking for a 24-port SFP switch. Each of the two switches in the subject meets that requirement. If I went with the ME switch over the 3750 (at about half the cost), what features/functionality if any, would I be giving up?
View 5 Replies View RelatedI have 2 ME3600Xs and utilize Broadcast and Multicast storm control on client facing interfaces. One of my ME3600s is reporting a Multicast storm and that a packet filter action has been applied. The strange thing is that it is showing up on an Admin Down interface that has nothing connected to it. [code]
View 2 Replies View RelatedOur customer has a Cisco ME3600X with the IOS me 360x-universalK9-mz.122-52.EY3.They are saying that is not possible to configure the "switchport port-security mac-address sticky" in the interfaces and want to know whether any additional license is needed.As far as I know there isn't any extra license to activate this feature and also I believe the ME3600 switch should have this feature with the universal IOS, isn't that right?
View 1 Replies View RelatedJust finished my first build and everything went pretty smoothly but my wireless network card wasn't working. I noticed after I opened it back up that in order for my to screw the card in place it made the right side of the card tilt up.
So I just set it in the PCI slot correctly but there's no way for me to screw the card in place. I know my MOBO is set properly. My graphics card fits perfectly.
i have a brand new dell studio 1558
on my old computer i used an external PCMCIA modem from my cellular company , the modem uses a sim card to connect to the internet..
can i place the sim card inside the computer and use it as i used the previous modem ?
[URL]
Every one i want to know ws-c4503E series 3 -slot chassis . I have compatibility issues with MEM-C4K-FLD64M AND S45EIPBK9-12240SG will work.
View 2 Replies View RelatedCisco 1900 , 2900 and 3900 have Interface Slots and Service Module Slots , My question is which type of card is support this slot.
View 6 Replies View RelatedI've got this syslog alarm from nexus 7018. I am wondering what the slot 19 is here.
2013 Jan 15 23:59:22 r1 %PLATFORM-3-EJECTOR_STAT_CHANGED: Ejectors' status in slot 19 has changed, Top Ejector is OPEN, Bottom Ejector is CLOSE
2013 Jan 15 23:59:24 r2 %PLATFORM-3-EJECTOR_STAT_CHANGED: Ejectors' status in slot 19 has changed, Top Ejector is CLOSE, Bottom Ejector is CLOSE
I remember there is one command which can tell you which memory slot has how much big memory in Cisco 2800 or 3800. But at this moment, I just couldn't recall this command. I checked "show diag" but didn't see any information about memory.
View 9 Replies View RelatedI have cisco 4510R L3 switch with installed 2 Sup on slot 5 and 6. the current active Sup is in Slot5 i want to make active Sup6 in slot 6 which is currently standby sup in chassis. Is there any way to make standby Sup to ACTIVE without reloading any of the Supervisor. however there is two way as per my understanding -
1. we can reload the active Sup so that standby Sup will take charge. - (redundancy reload shelf)
2. we can focefully switchover the state of Sup's by (redundancy forcefully swithover) but in above both cases reload will be performed by one of the supervisor. which i don't want.
There is a cisco ws-c6509,recently it appear error log “%FABRIC-SP-6-TIMEOUT_ERR: Fabric in slot 5 reported timeout error for channel 11 (Module 3, fabric connection 1)”. When I reload the device,the error log disappear.But a few days later,it appears again.I try to replace the slot 3 (WS-X6704-10GE),the error log continues.The IOS version is 's72033_rp-ADVIPSERVICESK9_WAN-M), Version 12.2(18)SXF8"
View 1 Replies View RelatedDo you know if the following Cisco switches ME3600X ME3800X support Netflow? I need to collect data on interfaces and export it to an external Netflow collector installed on a server. In other word, I need to be sure that those switches support the following command (or similar):
ip flow-export destination <IP> ip flow-export source <Interface> ip flow-export version 5 ip flow-cache timeout active 1 ip flow-cache timeout inactive 15 snmp-server ifindex persist !
[Code].....
I have this 2801 in a critical environment. We had a brief power blip, and even though the router is on UPS, something happened. Anyway, after working with TAC, they determined the flash card had gone corrupt. Lucky for me I had a spare 2801 in my office, I grabbed that flash card and plugged it in and we're back up and going.
TAC sent me a new flash card. No matter what I do, I cannot get IOS to load on this thing! I am stuck in rommon. Here's what I've tried:
tftpdnld in rommon, times out. using another 2801 as a tftp-server. doesn't complete. using xmodem. ugh. never seems to get started. booting the router with a known good flash card, so I can get to ena, and "copy tftp flash".
have used tftpd32, Solar Winds TFTP server, What's Up Gold TFTP server, and open source tftp from sourceforge. With the tftp32, it always gets to exactly 73% download and then times out (it says, I have a feeling it's noty really a timeout). I have tried having the router and tftp server the only devices on a switch, i have tried the router plugged directly into the tftp server with a cross connect cable. No happiness. The open source tftp server reported (and I have to paraphrase, I am not near the router) "client does not support block number recount" or something like that. The client being the 2801.
The iOS file is about 45M. Someone asked me if the flash card was formatted...would that matter? would the tftp even start if it wasn't?
OK, I've gone on long enough. TAC is dispatching a new card AND 2801!
Recently my company buy a EHWIC4ESG card and put into the cisco 1941. The reason we buy this card is because the in built two network ports of cisco 1941 are being used up. g0/1 is being connected to the internet and g0/0 is being connected to the office switch (192.168.5.x)
We have two servers (192.168.6.x and 158.55.33.x) that required to be connected to this router 1941 where the router will be configured as VPN for external user to access this server.
The EHWIC4ESG card is put into the router 1941 and after typing the "running-config" command, i could see it create a vlan 1 interface and
interface GigabitEthernet0/1/0
interface GigabitEthernet0/1/1
interface GigabitEthernet0/1/2
interface GigabitEthernet0/1/3
[Code]...
I have an Metro network running ISIS to different locations. There are severals vrf's on different VLAN's with separate ISIS routing processes. ISIS is running in L2-Only There are two redundant hub routers (ME3600X) that are placed centrally.Connected to each of the ME3600X is an ISR2951 that connects to the internet and handling backup connections over DMVPN. Over those DMVPN tunnels I run MPLS over GRE and routing with BGP. The leaves are IBGP neighbours, and the central ISRs are route-reflectors. In those routers I redistribute from BGP to ISIS and vice versa. The IBGP has an admin distance of 200 and the ISIS route has 115, so in normal operations the ISIS route is installed in the FIB.
My problem is that when an primary connection goes down, I want the backup route via the DMVPN to be redistributed from BGP in to ISIS, and the traffic to go over the DMVPN instead. But what will happen is that when the ISIS route over the primary connection disapear both my ISR's will compete in advertising the route, and as one of the ISR's is advertising it the other one recives it and since ISIS distance are better it will prefer that one, and the other way around. So my routes are coming and going, and everything is unstable. With just one ISR, it works as it should.I tag the route redistributed in to ISIS, but there is no way to add a incoming distribute list to the interface of the ISR in ISIS, otherwise I might have stopped the route in to the ISR if it was advertised by the other ISR.
Also tried to put the ISR's in different L1 areas in ISIS and redistributed L2 to L1 in the ME3600X with an route-map filtering the routes learned from BGP from the ISR's. That works for failing over, but then I'm stuck on the DMVPN bacause when the primary way comes back again, the L1 learned from the ISR is prefered before the L2 learned from the neighbor over the Metro network.
I was thinking of extending the BGP in to the ME3600X, I could of course use EIGRP with distribute-list's between the ME end the ISR. [code]
How do we find out the serial no. for a CIP card on a cisco 7500 router.
View 1 Replies View RelatedI have 3725 router with internal CF and external slot for CF. I tried upgrading and ended up deleting the iOS version on the internal flash, and can not now put the iOS back!! I turned it off.... so there was no active iOS..
I have tried formatting the CF card on an 1841 but the 3725 won't read it. It is obviously stuck at ROMMON
What is the correct way to format a CF card so my 3725 will read it and I can get an iOS back on it!!
I am looking a 16 or 24 Port Ethernet (NON POE) card for my 2800 Cisco Router NM-16ESW is EOL/EOS and the replacement is shown as SM-ES2-24 However SM-ES2-24 is not supported on Cisco 2800 Series.
View 2 Replies View RelatedI have a Cisco 1811 with a 4/port Serial Async/Sync (HWIC 4 A/S) and another 2 port A/S serial wic. My router seems to have a problem reading the 4/port card. I did some research and it looks like there shouldn't be a compatibility issue.
View 7 Replies View Relatedi have a nexus 5k with a l3 card i'm not able to bring online
NX-OS is:5.0(3)N2 (1)
L3 card is:L55D160L3
i inserted L3 module several time with the same resul...if i perform a show module i see the card offline. At the boot switch show an error message:
L3 module is down due to a BTCM down..
I urgently want to replace a faulty line card WS-X6748-SFP with a new one. The switch concern is a 5609-V-E operating in Virtual Switching System mode.How long do you suggest the down time will be?
View 1 Replies View RelatedI have a customer that in the past has been using 6506E chassis with Sup32 and the WS-X6196-21AF cards for their closet.With the End of Sale of this combination and the announced End of Sale of the Sup720-3B announced, this kind of pushes the configuration to a Sup 2T.BUT the SUP 2T does not support these low speed high density cards.
Is there a card coming that will address need? Customer generally has had dual sup32's and 3 to 4 cards of the 96port AF.They stock spares besides haveing smartnet on the boxes or moving to a different platform like the 4510R+ or stacks of switches will mess them up.
what is the best configuration betwen vmware ESX server with 10 Physical NIC card and cisco 6500 , This ESX Server host 12 vm with VLAN 100,150.200
View 10 Replies View RelatedI am attempting to add an additional ethernet port on a Cisco 2620 router using a NM-2FE2W card, however the card is not being detected. I read that this card is compatible with this model router, but I have also notice that there is a version 2 of this card. Have I ordered the wrong card or do I possibly have a defective card? My ISO version is 12.2(26) on the router.If this card is not compatible, what is the recommended card for adding an additional ethernet port on this router?
View 2 Replies View RelatedI can't find anywhere whether it is possible to create a vPC domain with 2 Nexus 5548UP switches, where only 1 Nexus 5548UP has a L3 daughter card.
View 3 Replies View RelatedI will be adding two WS-X6716-10GE cards in a CAT6509 soon, and will create 4 port channels with 3 ports each in the new cards, but I do have a few questions:
1 - I will be adding cards in slots 3 and 8, can I mix and bundle ports from both modules into a single etherchannel, I mean, like two ports in slot 3 and 1 port in slot 8 to create a PortChannel ?! Or can I only bundle ports in the same card/port-group in a Etherchannel using this WS-X6716-10GE card?
2 - Do I need to issue the hw-module slot x oversubscription port-group y command in order to be able to bundle ports in the Etherchannel I need to create ?! I will be using 4 Etherchannels (LACP) with 3 ports each, running in trunk mode. So I guess, I will be using something like:
int tengig 3/1
switchport mode trunk
switchport trunk encapsulation dot1q
logging event link-status
[Code] ....
Cisco Catalyst 6509 Chassis.We have moved a line card from slot 8 to slot 6, but config remains for the line card in slot 8 and nothing is seen in slot 6.
We are running on IOS Verison 12.2 (33SXH2A) i.e. VSS.Blade model number is WS-X6748.
Is there any in depth documentation on how to configure a VWIC3-4MFT-T1/E1 card? It will sit in a CISCO2911/K9. The network is point to point T1s - a quantity of four coming into this router.
View 1 Replies View Relatedwhen replacing a line card on a 6500, i gather there is no config stored on the card, its all held on the sup, so when i put in another card the config will be the same?
View 2 Replies View RelatedNeed to know if i can add 1 FE card to 2650XM or 2620 Routers.i know we can add Ethernet card but it is only 10MB .
View 2 Replies View RelatedI have installed a EHWIC-4ESG card into my 2911 router running IOS Ver 15.1(4)M2. When I do a show diag, I can see the card, but I get the following line "Could not get card instance pa_bay=0 slot=0." Am I missing a step, do I have change something, is it not compatible (all that I have read, states that is)
View 3 Replies View Related