Cisco Switching/Routing :: Does 2650xm Or 2620 Can Have 1 Additional FE Card
Nov 10, 2011Need to know if i can add 1 FE card to 2650XM or 2620 Routers.i know we can add Ethernet card but it is only 10MB .
View 2 Replies
ADVERTISEMENT
Cisco Switching/Routing :: Connecting 2650XM - 2620 Router Back To Back WIC - T1?
Nov 25, 2011I have 2650XM router and 2620 Router Both routers have built in WIC T1 CSU/DSU cards
2620Router --
2620Router#sh int se0/0
Serial0/0 is down, line protocol is down
Hardware is PQUICC with Fractional T1 CSU/DSU
Description: DTE side
MTU 1500 bytes, BW 1544 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation HDLC, loopback not set
[code]....
My question is that cisco website says there are two type of cable connections for this type of config --which are --T1 CSU/DSU ConfigurationSet one CSU/DSU to clock source internal, and the other CSU/DSU to clock source line. The linecode, framing, data-coding, and timeslots must be set the same on both CSU/DSUs.Four-Wire 56k CSU/DSU Configuration For my network connection which type of config i should use??Secondly i try to connect these ports by normal crossover cable it did not work.So for this type of connection i know i need T1 cross over cable-- which has RJ 48 connections at both sides.I check cable from ebay which is RJ45 RJ48 cross over -- will this cable work in my router to router connection.
Cisco Switching/Routing :: 2620 NM-2FE2W Card Not Being Detected
Dec 28, 2011I am attempting to add an additional ethernet port on a Cisco 2620 router using a NM-2FE2W card, however the card is not being detected. I read that this card is compatible with this model router, but I have also notice that there is a version 2 of this card. Have I ordered the wrong card or do I possibly have a defective card? My ISO version is 12.2(26) on the router.If this card is not compatible, what is the recommended card for adding an additional ethernet port on this router?
View 2 Replies View RelatedCisco Switching/Routing :: Which WIC Or NM Ethernet Card Compatible With 2620
Jan 10, 2012Which WIC or NM Ethernet card is compatible with a 2620, (non XM) router? I have seen conflicting information on compatibility. I am wanting to connect this router via an Ethernet Port with a non Cisco router that is connected to my ISP.
View 1 Replies View RelatedCisco Switching/Routing :: 2948 / 2620 - Single Interface Routing
Jan 7, 2012I am a recent student to Cisco products and I have purchased some (what I thought was good) lab equipment to learn with on a budget. What I have is a 2948G switch and a 2620 router. My issue is this: the router has only one fast Ethernet port. Is it possible to use V LAN's and V LAN Interfaces on the router and switch to somehow emulate a second interface to connect to a WAN or sub net?
View 11 Replies View RelatedCisco Switching/Routing :: 2620 - Get New Home Lab / Configuration?
Feb 10, 2013I finally decided to get my own home lab so that I can configure to my hearts' content and not have to wait for access at the school to do it. I have three 2620 routers inter-connected with wic2t cards, and five 2950 switches. I have already set the config reg. on the routers to 0x2102 so that I can save my configs when I power down. When I pulled up the config regs on the switches, they all had 0xf as the reg number. Is this a good config reg number to have if I want to save the config before I power down?
Also, what would be a good ios version to have running on the switches and also the routers? I have access to other cisco IOS' but I want to double check. With this setup I would practice bgp, ppp, frame relay, rip2, ospf,eigrp, stp, pvst,pvst+, Rapid pvst+, rstp, and mstp.
Cisco Switching/Routing :: 2650 / 2620 - Support For MPLS
Oct 29, 2011Does 2650 and 2620 support MPLS ? If yes what IOS version should i download?
View 10 Replies View RelatedCisco Switching/Routing :: 2620 - TFTP Opening IP Error
Aug 25, 2012I am trying to create a backup of my 2620 router so I can use for GNS3.
I have only configured the IP address on my FastEthernet port. Having many issues with no connection to my pc, finally I found that you must enable the interface 'no shutdown'. Now I have a valid connection
I have made no other configurations on this router, everything else is default.
I can successfully PING from both ends
**PROBLEM: My problem is that when trying to 'copy flash' to my TFTP server, the response is**
".....
%Error opening tftp://192.168.1.3/c2600-advsecurityk9-mz.124-1a.bin (Timed out)
Router"
Is there another setting I should enable? Remember I have made no other configurations bar the ones above.
Cisco Switching/Routing :: 2620 - Unable To Connect To Internet
Jul 9, 2012My configuration is the following
Router ISP >>> Switch 2940 >>> Router 2620 >>> Host (Tacking dhcp from my 2620)
I got servers and other switches 2950 working perfect from the 2940....but the 2620 or even a Switch 3550 (in router L3 port), has the same issue...do not share connection with Host's behind them, I got IP on the host, pinging the Fa0/1 (dhcp), pinging the Fa0/0, but cannot ping the GATEWAY and not surf the internet.
Cisco Switching/Routing :: 2620 XM / 1605 R - Compatibility With Verizon Appliance
Jan 12, 2013I am new to Cisco networking (I just passed my A+ test and am working on my Network + test with an end goal to finish with a CCNP) and I bought a Cisco 2620 XM and a 1605R to figure out how to setup and practice on. In my house we have Verizon Fios with the standard Verizon appliance feeding internet to the rest of the house. My question is that will my Cisco appliances be usable with an out connection from the Verizon appliance? I am concerned because the connection that comes into my room from the Verizon router would be considered a LAN connection, not a WAN? Also in order to configure the router, I believe it needs an RJ-45 to serial to plug into a computer for setting up. My computer doesn't have a serial port so will an RJ-45 to USB work (since that is serial as well)?
View 3 Replies View RelatedCisco Switching/Routing :: 2950 / 2620 / 2621 - How To Get WAN Connectivity Back To Switch At End Of Network
Jan 27, 2013I have a lab setup to take my CCNA and CCNP and I'm having issues trying to get WAN connectivity back to a switch at the end of my network. My lab environment consists of 1 - 2950 switch, 1 - 2620 and 1 - 2621XM. I have 1 Ethernet connection from each router to the switch and 1 serial connection from the 2620 to the 2621XM. I have the serial interfaces in a shutdown state right now so there is no loop since I do not have Spanning tree setup on the ports on the switch yet.
Right now using the fast ethernet ports on the routers and I have no issues its when I shut down those Ethernet ports and try using the serial interfaces when I start having issues. So my network layout is Ethernet from switch port f0/4 to port f0/0 on 2620 and serial from s0/1 on the 2620 to s0/2 on the 2621XM. My 2621XM f0/1 is whats connected to the WAN and I have no issues getting to the WAN from my 2621Xm or my 2620 but when I try pinging any website or even my WAN default gateway from my switch I get nothing!
Ive also noticed that when I do a IP NAT translation (after accessing the WAN from my 2620) on my 2621XM the source IP is of my serial connection not the ip of my 2620 router? I have my default gateway on the 2620 as the the IP of my serial interface on the 2621XM and vice versa because my LAN network is 172.16.1.0 and my WAN is 172.16.9.0. I have a /31 setup between my serial connections 172.16.11.0 (s0/1) is on the 2620 and 172.16.11.1(s0/2) is on the 2621XM. I used the SDM (ver 2.5) to setup NAT to have f0/1 with Nat outside and s0/2 as Nat inside. Encapsulation is HDLC between the serial links. Ive attached the running configs of the switch and routers.
Cisco WAN :: PIX 520 To Add Another Eth3 Card To Use For Additional IP Range
Aug 2, 2011I have an existing external IP block on eth1 which is working fine. I have another eth3 card which I want to use for my additional IP range.So my ISP gave me a new /27 block is addition to what I have now. This block is supposily active and nothing is needed to configure on the ISP router, it is said that it is autmatically available and ready to use once I configure my PIX.I am using the PIX GUI and running into an error while trying to create a NAT pool "Start and end addresses overlap with existing range"
View 53 Replies View RelatedCisco WAN :: 2851 / Additional ADSL Card - Grouping Or Balancing?
Oct 11, 2011We have a Cisco 2851 router with Advanced Securit IOS version 12.4(13r)T. In the router we have a WIC-1ADSL connected to business DSL with a static IP. We were wondering what our options are regarding adding another WIC-1ADSL card and DSL line and either grouping the two or load balancing to increase our bandwidth. Unfortunately at this time DSL is our only option.
View 1 Replies View RelatedCisco Switching/Routing :: Using 871W As Additional Access Point
Apr 25, 2012I have an 871w set up to add wireless connectivity to an existing network. When adding a client to the physical interfaces to test VLAN internet connectivity, however, a DHCP address is assigned but internet traffic on the terminal never reaches the network nor does the network recognize the IP the terminal shows as being 'connected'. Also, pings sourced from the VLAN do reach destinations. I've attached my config file, I think it's a routing issue of some kind.
10.26.99.0 is the existing network. 10.26.99.1 is an existing 871w router set as the DHCP server for that network and 10.26.99.10 is a Windows Server 2003 DNS box. VLAN 2 and DHCP pool alpha were control sets for trialing DNS settings.
Cisco Switching/Routing :: Additional RJ45 Port Required On 1941 ISR
Nov 16, 2012One of branch locations has a Cisco 1941 Router . The port details are as follows
-Gi0/0 - ISP line
-Gi0/1 - Inside Network ( To a 2960 Switch)
Now they have procurred another line from ISP through which MPLS based VPN to the Main location is configured. What are the options I have , to terminate it on the Router ? As all the On board LAN ports are filled I guess I wont be able to do anything with the current setup .Are Switching modules available ? What is the Embedded-Service-Engine0/0 port that I see on #sh ip int b output ?
Cisco Switching/Routing :: 2960 - Enabled With Additional Priority-queue Out Command?
Feb 20, 2012I have a Cisco Catalyst 2960 with IOS Release12.2(53)SE (because of a contract I can not update it) -> the release notes for this version describe the following:
When auto-QoS is enabled on the switch, priority queuing is not enabled. Instead, the switch uses shaped round robin (SRR) as the queuing mechanism. The auto-QoS feature is designed on each platform based on the feature set and hardware limitations, and the queuing mechanism supported on each platform might be different. There is no workaround. (CSCee22591)
My config is as follows:
interface FastEthernet0/1 switchport access vlan 200 switchport mode access srr-queue bandwidth share 10 10 60 20 priority-queue out mls qos trust dscp auto qos voip trust no cdp enable network-policy 1 spanning-tree portfastMy question now is:When the priority queue is not enabled with auto-qos because of the software bug is it nevertheless enabled with the additional priority-queue out command?
Cisco Switching/Routing :: 3750G - Adding Additional Switch And Making It Stack
Feb 29, 2012I currently have Cisco 3750G which is currently live and active and fully populated and only have remote access.
I have an additional same switch which I would like to stack. My initial plans were to have 2 GIbit etherchannels, but I came across the option to Stacks both switch with each other.
When I do a show switch on the live switch its set as a Member: [code]
I would like to add the new switch to the stack without losing the config for the switch which is live. I understand that the highest priority of the switches becomes the Master but as the live switch is Priority 1, would chancing this affect the switches config, or would it lose connection at all?
Also when I plug in the new switch and it reboot how do I ensure it becomes the slave without rebooting the live switch?The cables on the switch do they have to go to port1 on the live switch and port 1 on the new switch or can they be port 1 and port 2?
Cisco Switching/Routing :: Additional Ethernet Switch Port For 2821 Router
Dec 18, 2012I have a 2821 router and need to add another Ethernet port.
However, all the Ethernet modules seem to be End of Sale and the suggested replacements are only compatible with the ISRg2 range.
Cisco Switching/Routing :: Catalyst 3850 - Additional License To Enable Controller Functionality?
Feb 10, 2013Based on what i am reading on the Catalyst 3850 datasheet, the controller functionality comes by default if i have a IP Base of IP Services license on the switch. Is this correct or do i need additional license to enable the controller functionality?What capabilities does below license provide ?
LIC-CT3850-UPG (Primary upgrade license SKU for Cisco 3850 wireless controller)
Cisco WAN :: IOS 2650XM To Buy 12.5 With Crypto
Sep 4, 2012I have a 2650XM 16mb flash, 64 mb ram. 12.2(12a). now I want to buy 12.4(25d) with crypto. How much is it? And where can I buy it ?
View 10 Replies View RelatedCisco WAN :: 2650xm / 2811 - Hierarchical QOS Over Two Logical Connection?
Nov 16, 2011We have two logical connection which are connected via 1 physical Ethernet interface to 2 routers in central sites. Both connections are 2 Mb/s. How can i classify the output traffic in order to shape both direction to 2-2 Mb/s.
There are not suitable "match" command!!! ??The branch routers are 2650xm and 2811.
Cisco Switching/Routing :: Using SD Card Slot On ME3600X
Mar 13, 2013we are trying to use the SD Card Slot on an Cisco ME3600X (ME-3600X-24FS-M) IOS Version 15.2(4)S2. If i try to copy a file from the sd card slot to the flash there is no Option like "slot0:" or something alse and no syslog message appers while adding the SD Card.
View 5 Replies View RelatedCisco Switching/Routing :: 2801 - Get IOS On Flash Card?
Mar 15, 2012I have this 2801 in a critical environment. We had a brief power blip, and even though the router is on UPS, something happened. Anyway, after working with TAC, they determined the flash card had gone corrupt. Lucky for me I had a spare 2801 in my office, I grabbed that flash card and plugged it in and we're back up and going.
TAC sent me a new flash card. No matter what I do, I cannot get IOS to load on this thing! I am stuck in rommon. Here's what I've tried:
tftpdnld in rommon, times out. using another 2801 as a tftp-server. doesn't complete. using xmodem. ugh. never seems to get started. booting the router with a known good flash card, so I can get to ena, and "copy tftp flash".
have used tftpd32, Solar Winds TFTP server, What's Up Gold TFTP server, and open source tftp from sourceforge. With the tftp32, it always gets to exactly 73% download and then times out (it says, I have a feeling it's noty really a timeout). I have tried having the router and tftp server the only devices on a switch, i have tried the router plugged directly into the tftp server with a cross connect cable. No happiness. The open source tftp server reported (and I have to paraphrase, I am not near the router) "client does not support block number recount" or something like that. The client being the 2801.
The iOS file is about 45M. Someone asked me if the flash card was formatted...would that matter? would the tftp even start if it wasn't?
OK, I've gone on long enough. TAC is dispatching a new card AND 2801!
Cisco Switching/Routing :: EHWIC4ESG Card Into 1941
Apr 4, 2013Recently my company buy a EHWIC4ESG card and put into the cisco 1941. The reason we buy this card is because the in built two network ports of cisco 1941 are being used up. g0/1 is being connected to the internet and g0/0 is being connected to the office switch (192.168.5.x)
We have two servers (192.168.6.x and 158.55.33.x) that required to be connected to this router 1941 where the router will be configured as VPN for external user to access this server.
The EHWIC4ESG card is put into the router 1941 and after typing the "running-config" command, i could see it create a vlan 1 interface and
interface GigabitEthernet0/1/0
interface GigabitEthernet0/1/1
interface GigabitEthernet0/1/2
interface GigabitEthernet0/1/3
[Code]...
Cisco Switching/Routing :: To Find Out The Serial No For Cip Card 7500
Feb 8, 2012How do we find out the serial no. for a CIP card on a cisco 7500 router.
View 1 Replies View RelatedCisco Switching/Routing :: 3725 - Format CF Card On 1841
Dec 26, 2011I have 3725 router with internal CF and external slot for CF. I tried upgrading and ended up deleting the iOS version on the internal flash, and can not now put the iOS back!! I turned it off.... so there was no active iOS..
I have tried formatting the CF card on an 1841 but the 3725 won't read it. It is obviously stuck at ROMMON
What is the correct way to format a CF card so my 3725 will read it and I can get an iOS back on it!!
Cisco Switching / Routing :: 16 / 24 Port Ethernet Card For 2800?
Jan 11, 2012I am looking a 16 or 24 Port Ethernet (NON POE) card for my 2800 Cisco Router NM-16ESW is EOL/EOS and the replacement is shown as SM-ES2-24 However SM-ES2-24 is not supported on Cisco 2800 Series.
View 2 Replies View RelatedCisco Switching/Routing :: Reading 4/port Card Of 1811
Aug 30, 2012I have a Cisco 1811 with a 4/port Serial Async/Sync (HWIC 4 A/S) and another 2 port A/S serial wic. My router seems to have a problem reading the 4/port card. I did some research and it looks like there shouldn't be a compatibility issue.
View 7 Replies View RelatedCisco Switching/Routing :: Nexus 5k With L3 Card Showed Offline?
Aug 30, 2011i have a nexus 5k with a l3 card i'm not able to bring online
NX-OS is:5.0(3)N2 (1)
L3 card is:L55D160L3
i inserted L3 module several time with the same resul...if i perform a show module i see the card offline. At the boot switch show an error message:
L3 module is down due to a BTCM down..
Cisco Switching/Routing :: To Replace A Line Card WS-X6748-SFP
Oct 18, 2012I urgently want to replace a faulty line card WS-X6748-SFP with a new one. The switch concern is a 5609-V-E operating in Virtual Switching System mode.How long do you suggest the down time will be?
View 1 Replies View RelatedCisco Switching/Routing :: High Density Card For 6500E And 2T SUP
Jun 5, 2012I have a customer that in the past has been using 6506E chassis with Sup32 and the WS-X6196-21AF cards for their closet.With the End of Sale of this combination and the announced End of Sale of the Sup720-3B announced, this kind of pushes the configuration to a Sup 2T.BUT the SUP 2T does not support these low speed high density cards.
Is there a card coming that will address need? Customer generally has had dual sup32's and 3 to 4 cards of the 96port AF.They stock spares besides haveing smartnet on the boxes or moving to a different platform like the 4510R+ or stacks of switches will mess them up.
Cisco Switching/Routing :: ESX Server With 10 Physical NIC Card And 6500?
Jul 14, 2008what is the best configuration betwen vmware ESX server with 10 Physical NIC card and cisco 6500 , This ESX Server host 12 vm with VLAN 100,150.200
View 10 Replies View RelatedCisco Switching/Routing :: Nexus 5548UP VPC Domain With 1x L3 Card
Apr 9, 2013I can't find anywhere whether it is possible to create a vPC domain with 2 Nexus 5548UP switches, where only 1 Nexus 5548UP has a L3 daughter card.
View 3 Replies View Related
