We have a Cisco 2851 router with Advanced Securit IOS version 12.4(13r)T. In the router we have a WIC-1ADSL connected to business DSL with a static IP. We were wondering what our options are regarding adding another WIC-1ADSL card and DSL line and either grouping the two or load balancing to increase our bandwidth. Unfortunately at this time DSL is our only option.
View 1 RepliesI have a router Cisco 1901 with 4 links ADSL load balancing, when I activate the links 4, DNS resolution become very slow.
View 3 Replies View RelatedI've 6 ADSL lines that provided by the same ISP and i've Cisco router 2600, so, how can I connect the six lines to the cisco router and running load balancing between them ??
View 3 Replies View RelatedI have an existing external IP block on eth1 which is working fine. I have another eth3 card which I want to use for my additional IP range.So my ISP gave me a new /27 block is addition to what I have now. This block is supposily active and nothing is needed to configure on the ISP router, it is said that it is autmatically available and ready to use once I configure my PIX.I am using the PIX GUI and running into an error while trying to create a NAT pool "Start and end addresses overlap with existing range"
View 53 Replies View RelatedI have a router Cisco 1901 with 4 links ADSL load balancing, when I activate the links 4, DNS resolution become very slow.
below the router configuration:
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
[Code].....
We have purchased a Cisco 1921 with twin ADSL after advice from a Cisco sales rep. However I am having trouble working out the load balancing/fail over config for the device.
I would like traffic to balance over both ADSL lines and if one goes down not to interrupt connectivity.
I had a look at ppp multilink but I am unsure our ISP (BT) support this?
!! Last configuration change at 13:18:34 UTC Tue Mar 29 2011!version 15.0service timestamps debug datetime msecservice timestamps log datetime msecno service password-encryption!hostname xxxxxx
[Code]......
I have the requirement to provide a Cisco Router with 3 x ADSL lines (768k) to increase the internet speed.PPP multilink is not supported from the ISP.
Is it possbile to distribute the traffic between this three ADSL lines?How can I configure this?
I have the following hardware configuration:
1 x CISCO1921-SEC/K9
2 x EHWIC-VA-DSL-B
The third ADSL line is connected over an ADSL modem at one fixed Router Gigabit interface.
Need to know if i can add 1 FE card to 2650XM or 2620 Routers.i know we can add Ethernet card but it is only 10MB .
View 2 Replies View RelatedWe have a cisco 1941 with line t1 Symmetric, (Also have Cisco 1841 unused, but works) I would like to connect the Cisco 1841 to four Adsl Backup lines in case the T1 or the Main cisco 1941 go down I know a BGP is needed on our ISP site,
How can i connect four Adsl lines to The cisco 1841 (Backup) and make them work in a Load Balancing way.
I have a customer with two WLC 5508's running 7.0.116.0. When I look at the RF Grouping I see both controllers in the 802.11b/g/n section (802.11b>RRM>RF Grouping). However, when I check the 802.11a/n RF Grouping, I only see one controller.Both are in Group Mode = Auto.
I also made sure they had the same NDP settings, and they are both in Transparent mode.
Default 802.11a AP monitoring
802.11a Monitor Mode........................... enable
802.11a Monitor Mode for Mesh AP Backhaul...... disable
802.11a Monitor Channels....................... Country channels
802.11a RRM Neighbor Discover Type............. Transparent
802.11a AP Coverage Interval................... 180 seconds
[code]....
WISM v7.0 VLAN Select. If the VLANs subnet to be configured under interface group MUST be having the same subnet.
Eg. VLAN1 - mask 255.255.255.248
VLAN2 - mask 255.255.255.120
Would these two VLANs be able to work together in interface grouping?
I have a 48-port 3750G switch (model # WS-C3750G-48TS-S). How do I determine which ports are grouped per ASIC on the 3750G switch? For example, is the grouping ports 1-8 is serviced by ASIC 1, ports 9-16 is serviced by ASIC 2, ports 17-24 is serviced by ASIC 3, etc. If it exists, what is the IOS command to show the mapping of ports to ASIC?
View 2 Replies View RelatedOn 45XX catalyst , bandwidth is allocated across six 8-port groups, providing 1 Gbps per port group. Example for the following line card : WS-X4448-GB-SFP
I want to know if there is the same mecanism on 3750X switches. I mean is bandwidth allocated across a group of ports like on 4500 catalyst ?
i have a problem with my adsl line connected on a HWIC-ADSL on router 2901 it was working good until yesterday the atm interface is down but the interface dialer is up .i connected this line into home adsl modem and the line is working good?
View 2 Replies View RelatedWe have a Cisco 2851 router that crashes every night. Below is the 'show log' output. The provider is telling us that it is our equipment. We have replaced the router and still have the same problem. Is it our equipment or the provider?
Feb 15 19:29:43: %BGP-5-ADJCHANGE: neighbor x.x.x.x Down Interface flap
Feb 15 19:29:43: %BGP_SESSION-5-ADJCHANGE: neighbor x.x.x.x IPv4 Unicast topology base removed from session Interface flap
Feb 15 19:29:44: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0/0:0, changed state to down
Feb 15 22:34:13: %CONTROLLER-5-UPDOWN: Controller T1 0/0/0, changed state to down (LOS detected)
Feb 15 22:34:15: %LINK-3-UPDOWN: Interface Serial0/0/0:0, changed state to down
We want to get MIB files for snmp v2 from Cisco 2851 Router running with IOS below,
c2800nm-advsecurityk9-mz.124-15.T7.bin
We have Cisco router 2851 and asa firewall. We configured on he router for IP phones and ISP connected. The ISP directly connected on the router and asa firewall connected to the router. We have plan to configure VPN on the router. We have available public ip address. if i configure the VPN on the firewall we need to configure firewall local ip address to public ip address. SO how to configure firewall local ip to public ip ? Where we can configure , mean on the router or firewall. Firewall and router configuration.
View 11 Replies View RelatedI have a Cisco 2851 (c2800nm-advipservicesk9-mz.124-25d.bin) Router configured with one site-to-site vpn. Is it possible to configure a failover vpn tunnel on this router?
View 8 Replies View RelatedI have an office with 50 users. I have both a 2851 and a 2921 available. Which one would be a better fit?
Comparativley, which is the more powerful unit?
Do I need to obtain license keys/files when upgrading a 2851 to IOS 15.x? I'm getting a bit confused seeing the documentation that says 1) IOS has gone to a universal image and 2) that feature sets are unlocked based on the installed license.
I was able to download a feature specific IOS image for the 2851 and it did not bother me about licensing upon boot up.
I read one post on here that stated 2800/3800 series (G1) do not have to worry about the licensing piece and that it's just 2900/3900 series (G2) hardware that require it.
Is the 2851 router meet these requirements ? if no. What is the must specific series of the routers suitable for this requirement:
1. Comprehensive interface range supporting T1/E1, NxT1/E1, FE, and High-Speed WAN .
2. Wide array of Layer 2 access protocols including Frame Relay, Ethernet, and PPP/HDLC .
3. Rich and granular QOS and instrumentation for prioritizing mission-critical traffic such as voice .
4. A modular platform with a broad range of interface options.
5. Network Address Translation (NAT), and IP Sec .
6. Four (4) auto sensing LAN Ports (10/100/1000) Mbps built-in routed ports.
7. WAN Interface Slots (4-6 option Slots) .
8. WAN Interface Modules (2xT1/2xE1/2xSerial/2xFE/DS3).
9. Memory (512/1024 MB DRAM) .
10. Built in redundancy (Power Supply) .
11. Two (2) Integrated GE ports with copper and fiber support .
12. Support for a Small form-Factor Plugged ( SFP) port for GE.
13. Support Network Timing Protocol (NTP).
14. Security: On-board encryption Support of up to 2500 VPN tunnels with the AIM-HPII-PLUS Module Antivirus defense support through Network Admission Control (NAC) many more essential security features .
15. Voice : Optional support for Survivable Remote Site Telephony support for local call processing in small enterprise branch offices for up to 240 IP phones.
16. Performance : Up to 1GB DRAM Up to 1GB Flash The maximum transmission unit (MTU) Up to 9576 bytes Throughput up to 1.2 Gbit/s .
17. 110/220 volts.
18. Warranty certified by Sis 98 or by OEM (original equipment manufacturer) .
19. Up to 115.2 Kbps for Console/Aux port with DDR capability.
20. Supports IPv6
I seem to be having an issue getting a 3xT1 bonded solution to work. I can get 2 out of the 3 T1s to come up and pass traffic, but I can not get the third one to be added to the solution.
Hardware: 2851
IOS: c2800nm-advipservicesk9-mz.124-15.T8.bin
Modules:
NAME: "VWIC2-2MFT-T1/E1 - 2-Port RJ-48 Multiflex Trunk - T1/E1 on Slot 0 SubSlot 0", DESCR: "VWIC2-2MFT-T1/E1 - 2-Port RJ-48 Multiflex Trunk - T1/E1"
PID: VWIC2-2MFT-T1/E1 , VID: V01 ,
[Code]....
Up to today I used Verizoon 4G to a Windows Visata box running Internet connection Sharing to get my home lab connected to the Internet . All was working well.
Today I had Hughesnet come and installl their service and I can no longer get access to the Internet from my PC netowrk. my VPN to my office for my IP phone coomes up an works just fine. At the router I do have Internet access which then leads me to believe that my problem is NAT related.
My router is a 2851.
When I enter PING 4.2.2.2 I get !!!!! but when i enter PING 4.2.2.2 SOURCE 192.168.69.3 I get .....
Here is my config info:
crypto isakmp policy 1
encr 3des
hash md5(code)
I have a Cisco 2851 (with a 4 port switch module) that I am trying to set up with two different internet connections, and have it route traffic out to them based on the source IP. One connection is a 50mb Comcast connection, another is our T1 that our servers are hosted on. The goal is to guide server/phone system traffic to the T1 and have the rest default to the Comcast. I currently have the 2851 connected to our Layer 3 switch (Dell Powerconnect 6224) with a subnet created between them. Static routes have been created on the 2851 back to all of our existing subnets. Traffic flows internally without a problem between the subnets and 2851 (and vice versa). I set up the 2851 with route-map's in the NAT to control the flow of traffic, with the default route set to the Comcast connection. Default route works great, speedtest shows full speeds and everything looks great. The problem happens when I apply my route-map policy to the internal LAN interface with the ACL list of IP's that I want to guide to the T1 (with a next-hop of the T1's IP address). I tested some tracert's and pings from one of the IP's in this list and they would stop at the T1 modem and not go any further. I did a "show ip nat translations" and noticed that the "outside" portion (right half) was blank for every IP that was in the ACL or related to the T1. So my guess is it looks like this is not doing NAT for the T1? I double-checked that I had my "ip nat inside" on the LAN interface and "ip nat ouside" on the T1 VLAN interface and Comcast interface and they were there.
View 6 Replies View RelatedI am using a 2851 router in mpls network. We had a power shut down activity recently and post to that i could not find any logs in the router.
View 4 Replies View RelatedI am trying to find information on what the max clock rate supported on WIC-2T on a Cisco 2851 and Cisco 3845 Routers.
View 1 Replies View RelatedI recently obtained a 2851 and have been battling this issue for a week now. An odd set of circumstances happen with the bootstrap startup process. If the router has loss of power or when reloaded; it fails to read the CF card and boots to rommon. I can tftp an image to it (tftpdnld -r) and IOS CAN read the flash card along with any saved configuration.In fact once in IOS, I can wr mem and print the hardware details of the CF card. Once I reload the router it goes to rommon, fails to open the flash, then sits until i tftp the image back. When the router load IOS, it also loads the startup config.I don't think it's a problem with the CF card as IOS can read it. I've tried formatting the card from IOS and from my pc as FAT, FAT16, FAT32, and NTFS - it didn't make a different. I updated the ROMMON to allow for USB booting but haven't purchased a USB Drive yet for testing. The upgrade didn't resolve this issue either. It almost seems like a firmware problem with the EPROM.
View 7 Replies View Related[URL]I ran across this on the cisco site and I wondering if it was possiable with two 2851's? The part that is most interesting to me is this part of the config (this looks like what allows the use of the y-cable)
redundancy
#
mode y-cable
how to have a redundant border router with a T1
Network newbie here asking an embarrassing question on logging We have a Cisco router with the following IOS version. I want to enable logging; so do I need to configure event-log enable before adding the following logging configuration?
View 3 Replies View RelatedI need a configuration example of MPLS with VPN as a backup Router cisco 2851
View 3 Replies View RelatedI am having issues bringing up a tunnel between a cisco 861 router and Cisco 2851 router. Tunnel has been dropping every week atleast once or twice. Usually router reboot fixes it but today it is just not coming back up. have updatee remote, reloaded the config still no use. It seems like it is partially coming up but I see the following two messages on the main router:
1- Death by retransmission P1
2- 11:03:03.789: %CRYPTO-6-IKMP_NOT_ENCRYPTED: IKE packet from 12.234.109.169 was not encrypted and it should've been
I have checked the config on both routers it is the same as the VPN was up and we didn't make any changes on either of the two routers.
I have Cisco 2851 router & need to allocate bandwith based on IP's. eg. 192.168.1.1 should use 7 Mbps & 192.168.1.2 should use 2 Mbps & 192.168.1.3 should use 1 Mbps. Let me know the configuration on how to execute it on a router.
View 4 Replies View RelatedI am looking to add a new connection between a Cisco 2851 and a Cisco 3745. Currently there are two T1 connections between them for a internal 192.168.5.0 network but I would like to add a ethernet connection to give a larger pipe for when transfering large files via that network. Can I just add the ethernet to the multigroup and shut the ethernet connection down when not needed(to limit it to t1 speeds) or is there some other way of doing this?
[code]....