Cisco WAN :: 2851 - Update Bandwidth To A Network?
Feb 6, 2013
I am looking to add a new connection between a Cisco 2851 and a Cisco 3745. Currently there are two T1 connections between them for a internal 192.168.5.0 network but I would like to add a ethernet connection to give a larger pipe for when transfering large files via that network. Can I just add the ethernet to the multigroup and shut the ethernet connection down when not needed(to limit it to t1 speeds) or is there some other way of doing this?
[code]....
View 3 Replies
ADVERTISEMENT
May 16, 2011
I have Cisco 2851 router & need to allocate bandwith based on IP's. eg. 192.168.1.1 should use 7 Mbps & 192.168.1.2 should use 2 Mbps & 192.168.1.3 should use 1 Mbps. Let me know the configuration on how to execute it on a router.
View 4 Replies
View Related
Nov 27, 2011
I currently have a 2851 router with 2Mbps point-to-point leased circuit on its serial interface and most of the time its congested. Any tool for measuring the current consumption that is happening on the link other than netflow.Was looking for something for a graph or chart displaying the current consumption rate.
View 2 Replies
View Related
Mar 9, 2013
I just finished a new build and updated windows and gpu and mobo drivers but my internet downloads are really really slow. Next to network controller it has an exclamation mark and when I run check for updates it say it was unable to find drivers for it. My motherboard is an asus maximus v formula and I did update the lan before connecting to the internet through usb with another computer.
View 3 Replies
View Related
Feb 8, 2011
We have a network of 20 computers here at work. We recently moved from using Outlook to Gmail for our email service. That change appears to have triggered a problem. No more than 5 computers at any given time can acccess the internet now.
View 5 Replies
View Related
Jul 18, 2013
I was wondering if there is a way to monitor the total bandwidth available at any given time? My ISP claims and is charging me for a certain amount of bandwidth but I suspect that during the day I am getting much less.
I would like to track available bandwidth continuously (or every 5, 10, 15 minutes) and log that data so I can show them the results. I'm on a Mac 10.7 but can use Windows XP also.
View 2 Replies
View Related
Jun 27, 2012
My laptop won't connect to the internet at all and status shows limited access to router. It was fine a few days ago until a Windows update. I did a system restore on it back to before the windows update and the internet was working just fine but then there was an automatic windows update again and the connection is gone again. When I try to troubleshoot it says the network adapter is not working properly. I'm currently using the main computer in the house. I can't access any network at all on my laptop and I'm nearly in tears. This has happened before about 7 months ago after a windows update. At that time I did a system restore and reinstalled the updates and it worked just fine. This time nothing. I have tried to check for updated drivers for the network adapters but windows says I'm running the recent ones.
View 8 Replies
View Related
Oct 15, 2012
I had a Windows 7 automatic update last night. Went through the process and when it was done, everything was working fine. I did a proper shut down and went to bed. Woke up this morning, turned on my laptop and now I have NO network drivers. Tried a system restore prior to the "critical updates" and that didn't work either. So what the.
View 3 Replies
View Related
Mar 18, 2012
I've been having a bit of a problem lately trying to play Battlefield 3 on my PS3 when other computers are running on my network.
I'm looking for a program or method to set bandwidth limits on some devices to try to guarantee the PS3 enough bandwidth to play without lagging.
With the research I have done what I can find is that there is something called Quality of Service (QoS), and traffic shaping -- which are good and fine but I don't believe my Westell router supports them and I don't want to have to do anything crazy with my router.
Also I am currently dual booting Ubuntu Linux alongside Windows XP, and I don't have XP set up because I want to install Windows 7 on that partition once I can read DVDs (in the hardware forum), therefor I would really like to find a Linux program that I can use to shape my network traffic.
View 2 Replies
View Related
Feb 13, 2013
Tier 2 and tier 3 purchase from tier 1 provider ,but how is bandwidth produced i mean how tier 1 provider gets bandwidth. and why tier 1 doesn't have to pay.
View 7 Replies
View Related
Feb 6, 2013
what part of active directory can you change your bandwith for the network and monitor how much bandwith is being used.
View 4 Replies
View Related
Jun 11, 2011
Without using another box as a router preferably. My Cisco Linksys router doesn't have any options for this but I heard you could possibly install some 3rd party firmware to get around that. This would be a last resort for me What I'm hoping for his some piece of software that could do this
View 2 Replies
View Related
Jan 3, 2013
We run a small school and one of our campus sites is quite remote and our internet provider chares big dollars for internet downloads.One of our classes has just been upgraded to run over the internet and involves downloading 6Gig of video each time it is run. This will cost us approximatly $15 for each student and we have hunreds of student. We provide computers for this course work.
View 5 Replies
View Related
Aug 14, 2011
I want to control bandwidth of our computers in network. We are using TPLINK routers. I already done ipqos setting in the main router but it doesn't really effective. I also tried ipqos in the routers(which is used as WAP) but it also not effective.
View 8 Replies
View Related
Jan 8, 2013
how to up-date payroll from simply accounting when on a network
View 3 Replies
View Related
Oct 10, 2011
I have a DIR-655 router running 1.21. The last couple of years, I've always been checking the firmware version by pushing the "Check Now" button on the web management - it has always responded with "This firmware is the latest version. " I've been researching networking monitoring tools and came across this link: [URL] It requires that you update to the latest firmware - and this time I sued on the on-line link - and it turns out that the firmware version for my device is actually 1.35NA?So... first question is - why does my router tell me that 1.21 is the current version?I'd like the network widget - what are pros/cons of updating from 1.21 to 1.35NA?Have there been fixes to the scheduling portion? - 1.21 cannot handle 24-hour time properly. I also have to reset the router daily - sometimes more often - due to problems when used wirelessly. (Fortunately I try to use wired as much as I can.)
View 8 Replies
View Related
Aug 13, 2012
I have a cisco catalyst 2960-s PoE switch. I have a web access to the switch and am able to get statistics on each port. However, I am wondering if there is a way to have a diagram of the trafic on each port?
Also, what is the best way to monitor the trafic on a router ( i have a cisci 1811W)
View 9 Replies
View Related
Sep 9, 2011
We have 1 mpbs bandwidth line, but most of the time we are getting only 300-500 kpbs download speed, i want to send statistics report to our ISP, what will be best procedure to test the bandwidth report, i have checked in some websites like bandwidthplace and speedtest but these sites are not accurate, how to check the actual bandwidth we getting from ISP against 1 Mbps. We have solarwinds monitoring tool in this i have configured the WAN interface for 1 mbps
View 5 Replies
View Related
Feb 26, 2011
Anyway, I have a cable connection with a modem and a D-Link wireless router. Some of the users are abusing the bandwidth, making it difficult for others to surf the net.What's the easiest way to set a bandwidth limit for each user? Also, it is possible to do it through the router as I don't want to keep my computer running the whole time?
View 4 Replies
View Related
Jan 22, 2011
My college hostel has a broadband connection in each room, with individual servers, all of which are connected to a central server.Each hostel has a unique ip range(eg 10.3.14.1-10.3.14.255, and others like this, and students are allotted random ips). Each hostel has a particular proxy address that allows us to access the internand by low i mean, quite lowet, and each user has a fixed bandwidth(which is low). My question is, is there a way for one user of a particular hostel to use the bandwidth of multiple users of the same hostel(such that they are in the same ip range, and have the same proxy server for accessing the internet).i.e Is there a way for me to increase my bandwidth by using the bandwidths of other non allocated ips within the range of my hostel, such that with a single broadband connection, i can utilize the the unallocated bandwidth.
View 1 Replies
View Related
Jul 29, 2011
I have an internet connection (landline and wifi modem) at my parent's summerhouse as I need it for work. Nobody else does around here so I get constant nagging from neighbours to give them the password. I can't say no however I'm afraid they may use up too much of my bandwith connection which could lead to alot of money being lost from my part. Constant and stable internet is a must for my work. how can I limit the bandwith I give to them? Can I create a second public network with limited bandwith or something like that?
View 5 Replies
View Related
Dec 4, 2012
ok i have setup a subnet on my uncles network on which i am running a domain with server 2008. i am using a dlink di 624 router and wanted to know if i upgraded to a 300mbps router would this increase the bandwidth within my network?i know i am limited to what i am receiving from my uncle who is also limited to what he is receiving from the ISP. im not worried about internet speed. i want to increase client to server speed for both lan and wireless.
View 1 Replies
View Related
Aug 5, 2012
AT&T recently came out and replaced our Uverse modem, upon which iPad could connect to the new network, but neither of our laptops. I'm only a little technical with hardware/system issues, so after none of the more obvious troubleshooting issues worked, I started searching for more information and came across this site....great!! Eventually resolved the issue, suspect the wired connection through modem/router did the trick, but also updated the network adapter drivers. This (husband's) laptop was doing fine for a few hours, but then suddenly lost connection -- appeared that the network adapter was disabled. But when I went to enable it, it was gone!! It no longer appears in the Device Manager list at all. (It is/was an Atheros AR5700)
IPCONFIG /ALL results (wired via ethernet)
Microsoft Windows [Version 6.0.6001]
Copyright (c) 2006 Microsoft Corporation. All rights reserved.
C:Users jones>ipconfig /all
Windows IP Configuration
Host Name . . . . . . . . . . . . : tjones-PC
Primary Dns Suffix . . . . . . . :
[code]...
View 7 Replies
View Related
May 21, 2011
My dcs 2121 ip camera was working fine till I tried to update firmware 1.05(update_DCS-2102_DCS-2121_1.05_patch01_4927.bin). The IE screen mentioned update was ok(Firmware update successful:The camera will now reboot, please wait for 0 seconds) but my IP camera never come back after reboot! the red light in front never goes off. The camera is connected to my Windows 7 PC directly through a a network cable. no able to rest the camera as well .
View 5 Replies
View Related
Jan 20, 2013
I have a problem with 2 users in the home network who overuse the internet. They constantly watch YouTube with Pandora turned on or other streaming content.We have RW110. How can I limit their bandwidth, so when they use the internet they do not block other users ?
View 1 Replies
View Related
Apr 18, 2012
I am working at a client site today on a routing issue. I am currently working on an issue where a 3750 switch running EIGRP will not update its neighbor router when a network statement is added to the eigrp instance.The neighbor is a 3825 router.
Both the switch and the router have a common network which is 192.168.36.0/24.
Both the switch and the router are in a neighbor adjacency.
Both boxes have "no auto-summ" in the routing configuration instance.
I can run debugs on both routers (debug eigrp packets) and then I can watch queries and updates when I issue "auto-summ" or "no auto-summ". Also I see a "graceful restart" for the peers when this is done.I had an expectation that when I added the network (this is just an arbitrary network for testing, which is 172.16.69.0/24). I wanted to watch this network being sent in an update to the neighbor router.When I add the above mentioned network, there are no updates packets sent from the 3750 to the 3845. I have not had success to this point trying to resolve. I have followed the Cisco document "Troubleshooting EIGRP Flow Chart", but have exhausted all it has to offer and now it is at the point where it is telling me to contact TAC.
View 19 Replies
View Related
Jul 20, 2011
I have three laptops (running ubuntu with different kernel versions) with wireless adapter Intel Corporation PRO/Wireless 3945 ABG. Laptop A ----- Laptop B ----- Laptop CI created an adhoc connection in laptop A with: Essid: 'ad_hoc', IP address: 10.42.43.1, Subnet: 255.255.255.0, Gateway: 0.0.0.0, Now the laptops B and C can see the wireless connection 'ad_hoc' and I can connect to them after setting IP 10.42.43.1 and 10.42.43.2 respectively. So, I created the adhoc connection between 3 laptops. Now, I wanted to check the bandwidth between the different paths. The tool iperf was what I used for TCP bandwidth calculation. The bandwidth between A and B was around 4.5 Mbps , between A and C was around 4.0 Mbps but the bandwidth between B and C (B being server) was 677 kbps whereas C being server was 3.99. I don't understand how can the bandwidth drop so high when B was made the server. The system adapters are identical.
View 1 Replies
View Related
Sep 29, 2012
I think that my ISP is throttling my bandwidth at the modem . how access full available bandwidth.When the technician installed the fibre optic line and then the modem, he showed me an amazing 77MB/s (about 600Mbps) before the modem!!But after the technician left these were the test results after the router:
1) SpeedTests.net:
averages, after router, show: UP between 56/60Mbps & DN 45/75Mbps
2)Local Server Speed Test:
average: UP 45Mpbs & DN 170Mbps
A Japanese Internet savvy guy explained that NTT East throttles the available bandwidth at the building by specific apartment/modem settings related to individual contract bundles. I signed up for the top bundle: TV, Phone and Internet connections.This is my Hardware/ software setup:
OS: Win7,
Line specs:
Line type: IEC60874-14
Connector type: SC
Core across: 9 micrometers
Clad across: 125 micrometers
ITU-TG-652
NTT East fibreoptic TV/Internet/Telephone bundle (100Mbps best effort) Hikari Next Family Type but 10Mbps is considered within parameters
Asahi ISP Internet contract
Modem:
GE-PON (WAN+Coaxial TV antenna)
"SCM-GE-PON-<H>A GV-ONU D<1>" model
Router:
RT-S300HI (4 Giga ports + 1 phone)
Router & Modem have Japanese firmware which I cannot understand and, according to the NTT East, I must rent both modem and router from them and "will not support any other modem/router setup".I could not understand if it was because of technical or contractual limits.
I have tried to test my throughput after the modem but I could not figure out where the DNS, IP, WAN etc strings of numbers should go and, in the end, I simply cannot connect to the internet from my laptop directly to the modem so I cannot perform the same speed tests after the modem.
View 12 Replies
View Related
Oct 17, 2011
Is it possible to limit the bandwidth of one Mac on a wired network (only medium is the Netgear router WPN824v2)?
Both are Mac. Mine is newest iMac. Other one is a MDD PowerMac. Both are OS X. Mine is Lion.
I need to be able to throttle the bandwidth of the other computer.
View 6 Replies
View Related
Apr 7, 2013
I'm wondering if there is an easy way to monitor how much bandwidth is being consumed at any given moment for a home network.specifically, for the incoming/outgoing internet connection.My network is as thus:
DSL Modem -> Wifi Router (Linksys E4200v1 - PPPoE enabled here) -> Gigabit switch -> 2nd Wifi router (D-Link DIR-815 - DHCP disabled, repeats same SSID and password)
Most devices are connected directly into the switch, with one computer hard-plugged into the DIR-815 (I will eventually change this, as the 815 only has 10/100 ports).Basically, I want to easily be able to check how much up/down data is being sent for my internet connection. This means that I cannot use a program on a computer (I've used DL Meter before. Works great, but limited to a single computer).
The Linksys E4200v1 is using standard firmware, but I'm not opposed to loading DD-WRT onto it (was the original plan anyway, just never got around to it), if DD-WRT has this capability.Nice to have feature: Ability to see which devices are consuming what part of the bandwidth. Not necessary, but would be a cool feature.Alternatively, if there is a cheap (like $100 or less deal) box that can interface, say, between the E4200 and the switch, that can do this, that would work as well.
View 8 Replies
View Related
Feb 15, 2012
We have a Cisco 2851 router that crashes every night. Below is the 'show log' output. The provider is telling us that it is our equipment. We have replaced the router and still have the same problem. Is it our equipment or the provider?
Feb 15 19:29:43: %BGP-5-ADJCHANGE: neighbor x.x.x.x Down Interface flap
Feb 15 19:29:43: %BGP_SESSION-5-ADJCHANGE: neighbor x.x.x.x IPv4 Unicast topology base removed from session Interface flap
Feb 15 19:29:44: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0/0:0, changed state to down
Feb 15 22:34:13: %CONTROLLER-5-UPDOWN: Controller T1 0/0/0, changed state to down (LOS detected)
Feb 15 22:34:15: %LINK-3-UPDOWN: Interface Serial0/0/0:0, changed state to down
View 6 Replies
View Related
Dec 20, 2011
We want to get MIB files for snmp v2 from Cisco 2851 Router running with IOS below,
c2800nm-advsecurityk9-mz.124-15.T7.bin
View 1 Replies
View Related
Jan 31, 2012
We have Cisco router 2851 and asa firewall. We configured on he router for IP phones and ISP connected. The ISP directly connected on the router and asa firewall connected to the router. We have plan to configure VPN on the router. We have available public ip address. if i configure the VPN on the firewall we need to configure firewall local ip address to public ip address. SO how to configure firewall local ip to public ip ? Where we can configure , mean on the router or firewall. Firewall and router configuration.
View 11 Replies
View Related
