Changing Bandwidth And Monitor How Much Used For Network
Feb 6, 2013what part of active directory can you change your bandwith for the network and monitor how much bandwith is being used.
View 4 Replies
ADVERTISEMENT
Cisco LAN :: 2960S POE Switch - Monitor Network Bandwidth?
Aug 13, 2012I have a cisco catalyst 2960-s PoE switch. I have a web access to the switch and am able to get statistics on each port. However, I am wondering if there is a way to have a diagram of the trafic on each port?
Also, what is the best way to monitor the trafic on a router ( i have a cisci 1811W)
E4200v1 - Monitor Home Network / Internet Bandwidth?
Apr 7, 2013I'm wondering if there is an easy way to monitor how much bandwidth is being consumed at any given moment for a home network.specifically, for the incoming/outgoing internet connection.My network is as thus:
DSL Modem -> Wifi Router (Linksys E4200v1 - PPPoE enabled here) -> Gigabit switch -> 2nd Wifi router (D-Link DIR-815 - DHCP disabled, repeats same SSID and password)
Most devices are connected directly into the switch, with one computer hard-plugged into the DIR-815 (I will eventually change this, as the 815 only has 10/100 ports).Basically, I want to easily be able to check how much up/down data is being sent for my internet connection. This means that I cannot use a program on a computer (I've used DL Meter before. Works great, but limited to a single computer).
The Linksys E4200v1 is using standard firmware, but I'm not opposed to loading DD-WRT onto it (was the original plan anyway, just never got around to it), if DD-WRT has this capability.Nice to have feature: Ability to see which devices are consuming what part of the bandwidth. Not necessary, but would be a cool feature.Alternatively, if there is a cheap (like $100 or less deal) box that can interface, say, between the E4200 and the switch, that can do this, that would work as well.
Cisco Switching/Routing :: 3560 - Monitor Bandwidth Utilized By Servers In Network
Feb 6, 2013I have 5 linux and 3 Microsoft 2008 Servers, each connected to 2 Cisco 3560 Switches. The 2 Cisco 3560 switches are connected to 2 different Cisco 515e Pix. Is it possible that if i enable Port SPAN in any of the switchport and send a copy of traffic to any of the windows 2008 server, will i be able to monitor the bandwidth of the servers (Here I am only looking for traffic going from servers to PIX and then to internet, also vice versa).
Also will wireshark be able to differentiate specify the bandwidth of each servers seperately ?
How To Monitor The Bandwidth
May 25, 2011I show up at this business. They have about 40-50 systems. They have a 2003 AD server with a router, and 4 switches. There is also a dvr system on the network for cameras. Each switch is daisy chained together. Everything is working correctly except for the fact that the network drops about 5 times a day. Before they called us, they would just unhook one switch and plug it back in and it would work. At first, we took that switch and exchanged it with another switch in a computer lab to see if just the computer lab goes down. If it did, then that switch was bad. That wasn't the case, the whole network still went down. We had already left, but when we go back, our first choice will to see if there is a loop anywhere within the switch that will flood the network. Then, we were going to see if there was a switch that was getting a lot of traffic on the network to try to track it down. How can u monitor the bandwidth on the switches? They are 24 port switches. The switch is fs750/24 switch.
View 3 Replies View RelatedHow To Monitor Bandwidth (40 - 50 Systems)
May 25, 2011I show up at this business. They have about 40-50 systems. They have a 2003 AD server with a router, and 4 switches. There is also a dvr system on the network for cameras.Each switch is daisy chained together. Everything is working correctly except for the fact that the network drops about 5 times a day. Before they called us, they would just unhook one switch and plug it back in and it would work.At first, we took that switch and exchanged it with another switch in a computer lab to see if just the computer lab goes down. If it did, then that switch was bad. That wasn't the case, the whole network still went down.We had already left, but when we go back, our first choice will to see if there is a loop anywhere within the switch that will flood the network. Then, we were going to see if there was a switch that was getting a lot of traffic on the network to try to track it down.
View 4 Replies View RelatedCisco :: Monitor PAT Bandwidth With SNMP?
Apr 4, 2012Is is possible to monitor bandwidth utilization of a PAT on an ASA? We're running version 8.2.
View 1 Replies View RelatedBandwidth Usage Monitor Software?
Apr 21, 2012Any reliable free software to monitor my bandwith usage for my home computer?
View 4 Replies View RelatedSolarwinds Bandwidth Monitor Setup?
Aug 10, 2012I came across some free bandwidth monitoring software by Solarwinds while doing some reading on other sites. I installed the software and now im stuck at setup. The Softaware is asking for...
Ip Address/Hostname
SNMP Version
Community string
I'm assuming the IP Address/Hostname would be my computers IPv4 on the network and as far as the SNMP Version goes im not sure, I can either choose from SNMP v1/2c or v3. For the community string, I'm assuming its Public but im not completely sure.When I attempt to go to the next step is says the credentials test failed So obviously something I entered is incorrect.
Note: this is on my own home network. Im using a Comcast all in one router and modem.
Home Internet Bandwidth Usage Monitor?
May 6, 2011I have 4 laptops (WiFi), 2 desktops (LAN), xbox (LAN), and dish receiver (LAN) that are all connected to the internet using the method between the brackets. Recently i am running out of bandwidth, and what i am looking for is a freeware that i can install in one of the computers that could tell me which IP or MAC address used how much internet.I have read several articles: some articles point me to softwares which only monitor the computer that they are installed. Other posts argued that such thing can only be done through the main router. I know my router doesn't have such feature. I use SMC router.
View 3 Replies View RelatedWRT54G2 - Monitor And Limit Amount Of Bandwidth Everyone Uses?
Sep 10, 2012So lately this week, one rogue user from the boarding house has been downloading(possibly torrenting)/streaming to his/her heart's content resulting in extremely slow connections for everyone else. I've been using an Android app to list all devices connected to the network, and one-by-one, manually disconnected each one to find the problematic, bandwidth-hogging IP. I've found that said user continued to use up bandwidth even up to the wee hours of the morning.
I managed to find his/her IP address, I know I could just block sites/ports via the router's control panel but I guess it's not that simple because: a.) Whoever setup the wireless on our floor forgot the username/password combo(not even the landlady knows) b.) I've asked management about asking for access to the router. Being the IT student on the floor, I guess I'll take the responsibility of at least limiting the rogue user's bandwidth so everyone else on our floor has a fair share.
So my question is: is there a way to limit an IP/application's bandwidth usage via a non-router control panel method, without having to do a hard reset on the router? I have tried in vain to use the Android app I used, but all it takes is a router reboot to disable it (said user knows how to reset the router). It's been days since we've had a stable connection for legitimate schoolwork usage because of this one IP that's using up all the resources.
The router on our floor is a Linksys WRT54G2 and my operating system is Windows 7 64-bit.
Cisco :: Use MRTG To Monitor DSL Connection Bandwidth Usage?
Jan 24, 2013I want to use MRTG to monitor my DSL connection bandwidth useage.
Should I monitor:
ATM 0/3/0 or
Dialer 1 or
Virtual-Access 2
ps. is the 'BW' aspect of show interfaces important? I have 56Kbit/sec on Dialer 1, 100,000 Kbit/sec on Dialer 1 and 1024Kbit/sec on ATM.
Tool To Monitor Internet Connection And Bandwidth At Windows XP Desktop
Sep 26, 2011I need an tool to monitor the internet connection and bandwidth at my windows xp desktop.
View 4 Replies View RelatedCisco :: Using SNMP To Monitor Bandwidth Utilization History ASA 5510
Dec 22, 2008I matched the traffic statistics on one of my Cisco ASA site-site tunnels with the OID:1.3.6.1.4.1.9.9.171.1.4.3.1.1.25.4142 (cipSecTunHistInOctets). I was real proud of myself for a few days until I checked the history and found the OID wasnt working.After some troubleshooting I found that the last four digits (4142 in this case) change whenever the tunnel drops and re-establishes itself. Any way to collect tunnel utilization history on an ASA with SNMP? Is there a different OID I can use thats based on the endpoint IP?
View 2 Replies View RelatedHow To Monitor Multiple Network
Jun 12, 2012Let's say that I've multiple network (LAN A, LAN B, LAN C), how can I monitor all of these network.
View 1 Replies View RelatedChanging IP Address In Static Network?
Jul 11, 2011I am connected to a static ip network. This network sets local ips to connected computers but general ip is the same: static ip of network. When i go to "whatismyipaddress", I can see this static ip. I want to change my ip address. I have no chance to use proxy server or router connection. Is there a way to change my ip address? (Because some sites ban ip address, ex:rapidshare etc. and I need to change my ip)
View 1 Replies View RelatedNetwork Connection Icons Keep Changing?
Feb 23, 2013[CODE]My current problem is the internet just isnt working right. It is slow, choppy at times or doesnt load all items on a page. If it doesn load a page sometimes I click on the stop X, followed by refresh and the page pops right upSometimes if I dont get a complete page a refresh will fix it. It is just a pain to work with.There is an Network Connection icon in the right corner of the task bar. It is two small blue screens. It keeps changing from a red x, an exclamation point, and three blue balls or nothing. If I rest on the icon it flashes the status of the network:[CODE]
View 12 Replies View RelatedChanging Wireless Network Settings
Apr 4, 2011I had a disaster occur on my "guest" OS within VMware-Player. I had to start over from scratch! I am back in business, except for having the virtual machine recognized by my existing wireless network. The other two computers still communicate.I went through the wireless setup routine for the new VM. A new "ID" was assigned. Obviously, this is different from the one currently in use on the network. I have the settings info on a flash drive. Can I simply insert the FD in the other two computers and have the new ID replace the existing one?
View 14 Replies View RelatedChanging ISP Network / Router / Modem
Oct 21, 2011I've finally gone and done it. I phoned up aol and requested my MAC code.With my new ISP ( possibly ZEN ) if I keep my existing netgear router, can I keep my wireless connection settings the same i.e. network name, wep key etc.If, on the other hand I get Zen's router which is pre configured, I would need to set up the wireless again. Could I still use the same network name and wep key, or would I have to chose new ones.
View 3 Replies View RelatedChanging Or Getting Password For Wireless Network?
Apr 20, 2012I'm trying to get and change my password to wireless network to hook up my table pc I just got
View 1 Replies View RelatedUtility To Monitor A Network Status?
Jun 8, 2011The internet connection at our business goes down overnight, every night. We then have to turn off the router and turn it back on. It is not the fault of the ISP, but some setting somewhere, either in the router (SG 310 Snapgear) or in a particular program being accessed each night. Fact is, for the time being we are just trying to find out the precise time when this happens, so we can find out a reason. Is there a utility that can monitor the status and tell you at what exact point it stopped?
View 2 Replies View RelatedMonitor Network Traffic Without A Server?
Apr 28, 2011I am supporting a small call center of all Win7 machines. There is no server in house as everything is web based. Anyway, we want to find the bandwidth hogs and programs that I am used to using require servers for monitoring web traffic.
Are there any devices or software that is not a fortune that can give details on bandwidth usage?
How To Monitor Wireless Network Traffic
Feb 8, 2012i need to monitor the traffic on a multi users wireless route
View 8 Replies View RelatedD-Link DIR-615 :: Monitor Network Traffic On 3 Pcs?
Jan 24, 2011I keep getting warning on bandwidth usage , I'm using a dir-615 routers xp on all machines . The one pc that i use to d/l with I have the torrent monitor on and shows little traffic. Ive heard of a few pieces of s/w but these require software to be installed on all boxes Id like to be able to monitor from one box if possible ??
View 2 Replies View RelatedCannot Connect To Internet After Changing Wireless Network?
Mar 26, 2012I have two separate wireless networks in my house, one of them is for sharing my NAS data and the other is for Internet.problem is when I connect to the NAS network and after that I change my network to the other network, I can not connect to the internet ( I can connect to the wireless).
Just after restarting I can see the Internet
Home Network :: To Monitor The Router Connections
Jun 17, 2011if I have a unprotected wireless router and someone start using my router, will i be able to monitor what they doing using my router internet connection?
View 7 Replies View RelatedTools To Monitor Internet Usage Of Network?
Jul 21, 2011I would like a free tool that would moniter the internet usage of our network. it has about 20 computers and would like the following features: be able to show the usage of each computer the type of usage, ie, browsing, downloading, streaming a total usage Is there such a free program? would Microsoft Network Monitor 3.4 be able to do the trick if i learnt how to use it?
View 1 Replies View RelatedMonitor Internet Usage On A Wireless Network?
Apr 27, 2012we have a high speed internet and my modem is capable of wireless what I want to know, is there a way that I can monitor how much my daughter is on her computer and what websites she is visiting without having to install a program on her notebook or having to check her history etc? I would like to be able to do it all from my computer
View 2 Replies View RelatedD-Link DIR-655 :: Network Monitor Widget Not Working With Rev B?
Jun 9, 2011the Dlink Network Monitoring widget just shows: IP Address error?I'm on DIR-655 Rev_B hardware and 2.01 firmware.
View 1 Replies View RelatedCisco :: L3MPLS Monitor Network In QOS Environment
Mar 11, 2012i am using L3MPLS VPN services from a provider.They are doing QOS, like my Voice, Data, ICMP. all traffic is classified in their network and take different paths.Now sometime when we face voice issues, simple ICMP ping , TCP ping, will not give me insight if there are any packet losses, since Voice packets are taking someother path with in MPLS cloud due to DSCP marking of Voice pack to 46.is there any tool in which i can change DSCP value of my packets and test out network response? or any monitoring tool that can do this by default?i am looking for freeware at the moment or trial
View 1 Replies View RelatedServers :: Changing Network Information Of Multiple Machines?
Sep 25, 2012I have a list of servers that will be migrated from one subnet to another. Is there a script that can take my file that has the server name and the new IP address and modify the existing servers' network from the list? I want to place the script on the servers before I am ready to change subnets for preparation.
View 1 Replies View RelatedD-Link DCS Network Camera :: 920 - Changing Admin Password?
May 16, 2010Im having some problems changing my admin password on my DCS920
I know the default login is Login: admin / Password: "blank"
So I go into maintence, and there's an option to change the password.
it lists:
old password
newpassword
confirm
So I leave the old password blank and type in my new password in the following 2 spaces. I click apply and a window pops up asking me to enter username and password. I just enter admin and leave the password blank. I hit ok, and everything seems to update ok. So i log out, and try to log back in.
A window pops up asking me for my password. I type in admin for my username, and my new password, and it wont work
I type leaving the username blank, and type in new password... WONT WORK
I type admin, and new password again.. WONT WORK
I try password with first letter capital.. WONT WORK
I try password with ALL CAPS... WONT WORK..
Basically it wont let me log in as admin anymore. I figure I may have typed the password wrong the first time so I reset the camera and try the process again.. SAME PROBLEM.
Am I doing something wrong in changing my password ?
I dont wanna leave my default admin login as admin/"blank" , but when I try and change the password, it wont let me log in again as admin.
Monitor Broadband Usage Of PCs Connected To Wireless Network?
Oct 30, 2011How can I monitor broadband usage of multiple PC's connected to a wireless router/modem?
View 1 Replies View Related