Without using another box as a router preferably. My Cisco Linksys router doesn't have any options for this but I heard you could possibly install some 3rd party firmware to get around that. This would be a last resort for me What I'm hoping for his some piece of software that could do this
View 2 RepliesI live in rural Alaska and use satellite internet with 1.5mbps rate and 4gb rolling weekly download limit. I was wondering if there are any wireless routers I can buy that I can set a bandwidth limit for the specific router. Due to teenage girls in the house we hit the weekly limit in a day or two because of all the music videos and such that they watch on you tube, it is annoying getting limited to the 256kbps download rate so often.
View 5 Replies View RelatedI am a gamer living in my apartment with a room mate who loves to download music 24/7 and a girlfriend who loves to watch netflix. Needless to say, every time I go to play a video game I get shitty ping and lots of lag. From what I've gathered, DD-WRT's QOS is ****, and Tomato is the way to go in 3rd party firmware.
View 1 Replies View RelatedI run a business and have customers who would like to use my wireless internet. I previously had a completely open network that I would allow them to use, until someone illegally downloaded a movie and got us in trouble. I would like to allow use of the network again, but limit activities like this. Basically, so they could only do basic web browsing, etc.
View 1 Replies View Relatedhow to limit bandwidth only for user account in window 7...My PC has 2 account ..one is admin and other is user ..i need to limit the bandwidth only for user account ,do I need a software for this.
View 3 Replies View RelatedWe have two Cisco 2811 Routers setup with a GRE tunnel that we would like to constrain the bandwidth on to replicate a satellite connectinon of 400 kbits. We tried the bandwidth command 400, but from what I understand that is only for routing metrics and not actual speed of the interface.
View 5 Replies View RelatedI have a SG 300-20 small business switch and I would like to restrict bandwidth by gateway ip address but not by physical port or LAG. On the web interface, I can only do bw limiting per port or lag. I want to do bandwidth limiting by the IP addresses that I assign to vlans that my hosts use as a gateway ip.
View 3 Replies View RelatedI have a Cisco ASA5510 with two Cisco Catalyst 3560G switches plugged into it. Then I have 2 Cisco1400 Aironet WAPs plugged into the switches.
My goal is to limit incoming bandwith for two specific vlans. So users who are plugged into the switch or connected to the wifi can't go bandwidth crazy.
The rule I currently have setup on the ASA5510 is limiting internal bandwidth, I know shame on me.
So how do I setup a rule on the ASA5510 that will limit users external traffic on vlans without limit internal lan traffic?
I have an RV220W which I would like to set bandwidth limiting on. When we upload files to yousendit or an FTP server, it saturates the connection and essentially stops any other traffic until the upload is finished. Looking at the manual, it looks like it should do this, but does not seem clear to me.
View 1 Replies View RelatedSo my ISP (Telus) recently replaced our old router with a ZyXEL VSG1432. I'm currently having a huge lag issue when my roommates laptop is connected to our network. He is connected via wireless, I'm wired. So I did some searching around and I think i can solve this by limiting his bandwidth with QoS settings. I'm getting conflicting information here though. After logging into the router there are no QoS options yet according to ZyXEL's website url...This router should have the settings available. Is it possible that Telus does something to remove this feature? Is there some not so obvious way to enable QoS? Is there some other way to limit the bandwidth?
View 1 Replies View RelatedI currently use Verizon FiOS 20/5. The speed has been great until the day my cousin and his parents moved in. They also use our FiOS connection and I have came to the conclusion that my cousin's laptop is eating away all of the bandwidth which makes all devices using FiOS have extremely slow internet speeds. I know it is his computer because I logged in as admin to the Verizon FiOS page (192.168.1.1) and I saw that he is using several P2P applications and downloading torrents as well. Is there a way I can limit the bandwidth he is using so that the internet speed can improve? I looked at the QoS tab and tried to play around with the settings, but I don't want to mess it up. The router I have is Actiontec M1424-WR (Verizon FiOS 20 Down/5 Up). A lot of sources I am reading says that I have to use the QoS, but I don't know how to use it on the site.
View 3 Replies View RelatedI will have this one router. Its f0/0 will be for the Internet connection with bandwidth of 30Mbps. Its f0/1 will be connected to a switch for internal networks. This link will be separated to 3 VLANs for 3 internal networks. I'm wondering if there is a way to gurantee 10Mbps for each VLAN but allow use up to 30Mbps when another two VLANs are not using any Internet bandwidth? I only worry about download bandwidth from internet.The 3 internal networks will all have public IPs and they belong to their own subnets. There won't be NAT/PAT.
View 18 Replies View RelatedWe have a new 100MB internet service, but we only pay for 10MB and above that is a per/MB fee and not cheap. I want to limit all traffic inbound and outbound only to use up to 10MB on the outside interface of our Cisco 3825.
View 9 Replies View Relatedhow i can limit the bandwidth for a all my client conect to the AP, i have a Aironet 1200 with the 12.2.15 code.
View 3 Replies View RelatedI have a 4500 and 6500 that I'd like to be able to limit the bandwidth of layer 2 switchports. So for instance I have all GB blades but certain servers I'd like only to have connections of about 5 Mb per second or 15 Mb per second etc.
View 1 Replies View RelatedMy QA team needs to test number of special connectivity scenarios where their wireless connection has a limited bandwidth.Ideally, I would like to provide them number of SSIDs each of which has different bandwidth limitation.But so far I did not find a way to apply any bandwidth limitations to my 2504 Wireless controller and the 3602E AP.QoS has only 4 pre-defined modes which can't be set to a specific limit.
View 10 Replies View RelatedI 3750 doesn't support "shape" command under policy map. How do I limit the bandwidth to 3 M? [code]
View 3 Replies View RelatedCan I limit bandwith for guest in a wlan network with out Wlan controller? and of course, how can I do it?P.S.: I heard something about bronze profile in a wlan controller envoiroment, I need something like that but in an independent AP.
View 3 Replies View RelatedAny idea for limiting bandwidth on cisco 892F router? We have 2 VLANs through our LAN and one must be limited upto 1Mbps or 512Kbps.
View 2 Replies View RelatedHow do I setup this on the SRP527W? I already block most of the video stuff on the internet. But I want to make this one more step.
View 1 Replies View RelatedAnyway, I have a cable connection with a modem and a D-Link wireless router. Some of the users are abusing the bandwidth, making it difficult for others to surf the net.What's the easiest way to set a bandwidth limit for each user? Also, it is possible to do it through the router as I don't want to keep my computer running the whole time?
View 4 Replies View RelatedI have three laptops (running ubuntu with different kernel versions) with wireless adapter Intel Corporation PRO/Wireless 3945 ABG. Laptop A ----- Laptop B ----- Laptop CI created an adhoc connection in laptop A with: Essid: 'ad_hoc', IP address: 10.42.43.1, Subnet: 255.255.255.0, Gateway: 0.0.0.0, Now the laptops B and C can see the wireless connection 'ad_hoc' and I can connect to them after setting IP 10.42.43.1 and 10.42.43.2 respectively. So, I created the adhoc connection between 3 laptops. Now, I wanted to check the bandwidth between the different paths. The tool iperf was what I used for TCP bandwidth calculation. The bandwidth between A and B was around 4.5 Mbps , between A and C was around 4.0 Mbps but the bandwidth between B and C (B being server) was 677 kbps whereas C being server was 3.99. I don't understand how can the bandwidth drop so high when B was made the server. The system adapters are identical.
View 1 Replies View RelatedI think that my ISP is throttling my bandwidth at the modem . how access full available bandwidth.When the technician installed the fibre optic line and then the modem, he showed me an amazing 77MB/s (about 600Mbps) before the modem!!But after the technician left these were the test results after the router:
1) SpeedTests.net:
averages, after router, show: UP between 56/60Mbps & DN 45/75Mbps
2)Local Server Speed Test:
average: UP 45Mpbs & DN 170Mbps
A Japanese Internet savvy guy explained that NTT East throttles the available bandwidth at the building by specific apartment/modem settings related to individual contract bundles. I signed up for the top bundle: TV, Phone and Internet connections.This is my Hardware/ software setup:
OS: Win7,
Line specs:
Line type: IEC60874-14
Connector type: SC
Core across: 9 micrometers
Clad across: 125 micrometers
ITU-TG-652
NTT East fibreoptic TV/Internet/Telephone bundle (100Mbps best effort) Hikari Next Family Type but 10Mbps is considered within parameters
Asahi ISP Internet contract
Modem:
GE-PON (WAN+Coaxial TV antenna)
"SCM-GE-PON-<H>A GV-ONU D<1>" model
Router:
RT-S300HI (4 Giga ports + 1 phone)
Router & Modem have Japanese firmware which I cannot understand and, according to the NTT East, I must rent both modem and router from them and "will not support any other modem/router setup".I could not understand if it was because of technical or contractual limits.
I have tried to test my throughput after the modem but I could not figure out where the DNS, IP, WAN etc strings of numbers should go and, in the end, I simply cannot connect to the internet from my laptop directly to the modem so I cannot perform the same speed tests after the modem.
I'm wondering if there is an easy way to monitor how much bandwidth is being consumed at any given moment for a home network.specifically, for the incoming/outgoing internet connection.My network is as thus:
DSL Modem -> Wifi Router (Linksys E4200v1 - PPPoE enabled here) -> Gigabit switch -> 2nd Wifi router (D-Link DIR-815 - DHCP disabled, repeats same SSID and password)
Most devices are connected directly into the switch, with one computer hard-plugged into the DIR-815 (I will eventually change this, as the 815 only has 10/100 ports).Basically, I want to easily be able to check how much up/down data is being sent for my internet connection. This means that I cannot use a program on a computer (I've used DL Meter before. Works great, but limited to a single computer).
The Linksys E4200v1 is using standard firmware, but I'm not opposed to loading DD-WRT onto it (was the original plan anyway, just never got around to it), if DD-WRT has this capability.Nice to have feature: Ability to see which devices are consuming what part of the bandwidth. Not necessary, but would be a cool feature.Alternatively, if there is a cheap (like $100 or less deal) box that can interface, say, between the E4200 and the switch, that can do this, that would work as well.
I've got the E2000 at home for our private network.
We are three guys sharing a flat. We have personal laptops, work laptops, mobile phones, games consoles, tablets etc that connect to the internet.
Problem is that when someone downloads stuff, the speed is slow for the rest of us. So i was hoping i could set up something like three "channels" so each of us could have the same download speed, ie 1 mbs each regardless if others are using the network at the same time. And then maybe a guest network for all the mobiles and tablets etc. MAC filtering for access for our personal laptops should work.
We have a 20mbit cable network line.
Can i do all of this on the E2000 and how?
I have 4 laptops (WiFi), 2 desktops (LAN), xbox (LAN), and dish receiver (LAN) that are all connected to the internet using the method between the brackets. Recently i am running out of bandwidth, and what i am looking for is a freeware that i can install in one of the computers that could tell me which IP or MAC address used how much internet.I have read several articles: some articles point me to softwares which only monitor the computer that they are installed. Other posts argued that such thing can only be done through the main router. I know my router doesn't have such feature. I use SMC router.
View 3 Replies View RelatedI have a router with 2 service providers connectivity with different ASN and running with BGP.I've announce few IP-prefix by ISP-A and Few Prefix by ISP-B.Both are working well with redundancy.But,Problem is here, that the all uplink bandwidth goes through ISP-A link.I want to make it that, ISP-A routed ip-Prefix's upload data will go through ISP-A & ISP-B IP-Prefix's Upload data will go through ISP-B Link.
View 9 Replies View RelatedI have a Time Warner Cable business class service with no static IP, with a wireless modem which is plugged to a CAT5 distribution panel. On the jacks (2 other rooms on the house) I have a Linksys E3000 and a Linksys Valet router for signal boost and gadgets usage (TV, cameras, etc).The main router (TWC) has it's own external IP which TWC assigns to me and internally distributes via DHCP the range 192.168.0.x. With that said:
- The E3000 has a 192.168.0.6 IP -- this is fixed setup on the TWC router (ubee brand) by MAC address
- The Valet has a 192.168.0.7 IP -- this is fixed setup on the TWC router (ubee brand) by MAC address
- The main router has the 192.168.0.1 as the gateway and web-interface
Whenever I connect something to the E3000, it is distributing the 192.168.1.x range and the valet 192.168.2.x range.That works perfectly for my home based business until I decided to use more stuff on the network such as a IP printer, IP cameras, etc.
- The IP cameras are connected to the E3000 due to signal strength and I have manually assigned them the 192.168.1.15 and 192.168.1.16 IPs and ports 9001 and 9002.
- The printer is connected to the E3000 and I have manually assigned the IP 192.168.1.30.
Issue 1: Port forwarding On the main router (TWC - UBEE) I have tried to setup a port forwarding by informing the Local IP as 192.168.0.6 (E3000 IP), Internal Port 0, Public Interface IP (0.0.0.0), Ext Start Port 9001, Ext End Port 9001, Protocol - Both, Enabled Yes. On the E3000 I did the same config (screen shot attached e3000.png).This is not working properly. I can't get into the camera.
Issue 2: Printer/ The printer is only accessible if I connect to the E3000 (because it is on the 192.168.1.x network)
Issue 3: How to configure all the devices on the same subnet? If I want everyone to be on the 192.168.0.x network, how to configure properly the E3000 and the Valet? I have tried to force them into the same network but it would not work properly. It would not get an IP from the UBEE router (main).
Here's the layout: Cable modem in the basement. Several devices in which I'd prefer a wired connection in the basement. Upstairs on the 1st and 2nd floor of the house are many devices in which wifi is fine or preferred.Here's the problem: As you might guess, wifi is weak upstairs and certainly on the patio and 2nd floor. I have an access point upstairs that I've experimented with but it is flaky.
View 1 Replies View RelatedHow to install a wireless network in home environment?
View 6 Replies View RelatedI am a new student in networking, taking the CCNA courses, and now want to rewire my home. I currently have a cable modem and E2500 setup running my network. I want to get the modem and router out of my computer room and in the basement where the cable enters the house. I want to do this to clean up the computer room wiring a bit and to run line drops to different rooms in the house where the internet will be utilized.Currently there are two PC's, a laptop, a tablet, sometimes a phone, and an XBOX using the internet. I want to get my printer back up and running on the network but thats another story. Only one PC is currently hardwired. I would like to run two cables into the room with the PC and XBOX that are currently using wireless, at least two into the computer room for the PC and network printer, and one or two into the living room for the blue ray player and possibly an internet tv.
View 1 Replies View RelatedI have a D-Link DGL-4500 router and my landlord recently ungraded our internet connection. However, now I get this error message when I try to hook it up to the ethernet hub,"The addressing of the Internet side learnt thru DHCP conflicts with the addressing selected for the LAN side. Internet communications will be disabled until you have changed the LAN side addressing to resolve the problem."
View 3 Replies View RelatedI have setup a webserver on my home PC and I have forwarded port 80 on my router to the IP adress of the PC that is running the web server. The web server is working great; I can get to my web pages from outside of my home by going to http://MyIpAddress/Anyway, the problem is with the Windows Media Player plugin I'm using. I want to embed 6GB MPEG-2 videos into my web pages. I have some videos on my PC and I want to be able to watch them remotely by connecting into my web page. It works fine when I'm at home; other PCs can connect and play the videos no problem. The problem is when I'm at work. When I'm at work, I go to my web page (via my IP address in a web browser) and the Media Player plugin says "Connecting" for a minute, then it says Ready, but the video will not play. I tried using a smaller, AVI file (680 MB) instead to see if the problem was streaming such a large file, but the video still would not play.Do I need to foward more ports on my router so that Windows Media Player can connect back and get the information it needs?
View 4 Replies View Related