Cisco WAN :: 2851 - Nat Ls Giving Error
Apr 24, 2013
Up to today I used Verizoon 4G to a Windows Visata box running Internet connection Sharing to get my home lab connected to the Internet . All was working well.
Today I had Hughesnet come and installl their service and I can no longer get access to the Internet from my PC netowrk. my VPN to my office for my IP phone coomes up an works just fine. At the router I do have Internet access which then leads me to believe that my problem is NAT related.
My router is a 2851.
When I enter PING 4.2.2.2 I get !!!!! but when i enter PING 4.2.2.2 SOURCE 192.168.69.3 I get .....
Here is my config info:
crypto isakmp policy 1
encr 3des
hash md5(code)
View 1 Replies
ADVERTISEMENT
Feb 2, 2011
I am having issues bringing up a tunnel between a cisco 861 router and Cisco 2851 router. Tunnel has been dropping every week atleast once or twice. Usually router reboot fixes it but today it is just not coming back up. have updatee remote, reloaded the config still no use. It seems like it is partially coming up but I see the following two messages on the main router:
1- Death by retransmission P1
2- 11:03:03.789: %CRYPTO-6-IKMP_NOT_ENCRYPTED: IKE packet from 12.234.109.169 was not encrypted and it should've been
I have checked the config on both routers it is the same as the VPN was up and we didn't make any changes on either of the two routers.
View 4 Replies
View Related
Nov 22, 2011
we have ACS 4.2 and 2851 router with IOS 15.0(1)M4. There is authentication failure with error no 254. Is there any compatibilty issue with 15.0(1)M4 IOS
View 1 Replies
View Related
Mar 5, 2011
i have 2851 router and it is hanging when i login on it while it is hanging it gives me the following error message: [code]
View 2 Replies
View Related
May 28, 2012
We have Cisco 2851 Router part code CISCO2851-SEC/K9 facing issue while set peer configuration, issue description below.
Issue:We are facing the problem while configuring set peer as when we try to this we face error like 'unable to set peer.maximum numbwe of peer (40)exceeded'
We suspected the IOS issue hence we have gone for IOS upgrade for this Router but this error is still coming while configuring set peer.
Previous IOS: c2800nm-advsecurityk9-mz.124-15.T7.bin New IOS:c2800nm-advsecurityk9-mz.124-24.T7.bin
We are attaching here the snap shot of error that is coming while configuring the Router with set peer command along with show tech of the Router to understand this case brief.
View 1 Replies
View Related
Dec 26, 2010
I had these error messages on both my Cisco 2851 and on my Cisco Catalyst 6506.
On Cisco 2851:
%SYS-SP-3-CPUHOG: Task is running for (2000)msecs, more than (2000)msecs (4/4),process = SEA write CF process. [code]...
And on 6506:
Dec 27 15:20:55 MET: %SYS-SP-3-CPUHOG: Task is running for (2000)msecs, more than (2000)msecs (129/129),process = SEA write CF process.[ code]...
I have these IOS versions on my Cisco:
Cisco 2851: 15.0(1)M4
Cisco 6506: 12.2(33)SXI
View 3 Replies
View Related
Jul 24, 2011
I had been working on our client servers through Cisco VPN using internet datacard. But from past 3 weeks after logging into Cisco VPN using my username/password, when I try to connect to any of the servers, it is giving connection timed out error.
Whereas, my team members across other locations are able to connect to the servers using my VPN username/password.
I thought there might be some issue with my laptop or internet datacard. I got my laptop formatted, even tried out with fresh new laptops & new internet datacards, but the issue remains same.
I have tried using vpn_5.0.06.0160-k9 & vpnclient-5.0.05.0290-k9 to connect but issue did not get resolved.
View 4 Replies
View Related
Jun 20, 2012
i m trying to connect two routers a Cisco DPC3825 (r1) and DIR-655 (r2) and at the end getting the error. i have disabled the SPI firewall on r1 and connected an ethernet cable lan to lan between the two. i don't want to confuse with whatever the mess i have done previously,Tell step by step what i should do to connect these two routers.PS: in addition, the gateway ip of r1 is 192.168.0.1 with subnet mask of 255.255.254.0 and the gateway ip of r2 is 192.168.0.2 with subnet mask of 255.255.255.0. r1 has a ip range of 192.168.0.10 to 192.168.0.128 while r2 has range of 192.168.0.100 to 192.168.0.199.
View 7 Replies
View Related
Dec 26, 2012
After a successfull installation of NCS 1.2 into a vmware environment and run the setup I have the following error while trying to start or to have a status for NCS (ncs start ot ncs status):sh: /opt/CSCOlumos/bin/wcsadmin.sh No such file or directory
View 10 Replies
View Related
Jul 14, 2011
I have a WiFi printer connected to an CWAPP Cisco AP AP1250. I am using WPA2-PSK to connect to this AP. I find that the printer connects to the AP at times and at times it does not. I got an error message from the Capture an error on the backend controller of the network."Authentication Request received invalid RSN IE Mismatch WP2 algorithm"
View 3 Replies
View Related
Jul 5, 2012
I have one 5500 and about 15 Cisco 3502 APs.
The problem is that one of the clients loses the connection to the network time to time ,The error in the WLC logg is
*Dot1x_NW_MsgTask_0: Jul 06 17:42:38.934: %DOT1X-3-INVALID_WPA_KEY_MSG_STATE: 1x_eapkey.c:843 Received EAPOL-key M2 msg has invalid information when mobile is in START state - invalid secure bit; KeyLen 24, Key type 1, client 00:21:6a:af:be:70
View 4 Replies
View Related
Apr 22, 2013
I am currently on Time Warner Cable 10 mbps packge, and am using their wireless DOCIS3 modem/router. It is connected in my bedroom to the main computer. That computer stays connected. However, throughout the rest of the house (we have a two story townhome) it will drop completely or give limited connection...constantly. Sometimes I can have my laptop next to me and it will go out or give limited connection. The connection speed never drops, it just goes completely to no connection. Not for sure what is going on, if its on my end or time warner. Has been doing this for quite some time, the cable company comes out and changes the modem, but that's it, couple days later, goes back to doing it again.
View 8 Replies
View Related
May 15, 2013
I have an 1841 that was working fine - I could SSH to it with my Radius login and console into it with local credentials ("Fred").I added another use ("Mike") with priv 15 so the end user could log in locally via console if needed.After that, we can both log in via console, but when we try to enter privileged mode we get "% Error in Authentication", before even entering the password.I can still log in via Radius SSH with no problems and access privilege mode via SSH.What am I missing so we can have two different users be able to log in locally with different credentials and access privileged mode, and keep my ssh radius working?
View 3 Replies
View Related
Apr 4, 2011
We're seeing "OutDiscard" error on a LAN switch connected to newly migrated Cisco IP phones. All the other error counters are clean except for the OutDiscard. (please see attached "show int count err" output.) [URL].
According to the link above, the common cause of such discards can be to free up buffer space.(Am I seeing a switch buffer issue?) How to identify/resolve the cause of the OutDiscard.The switch is 3750-E running c3750e-universalk9-mz.122-44.SE6.bin
View 1 Replies
View Related
Oct 5, 2011
I was using my internet on my Acer Windows 7 operating system wireless just fine on Monday. I tried to use it on Tuesday and could not connect to the internet wireless any longer. I get an error message next to my network stating ""The settings [COLOR=green ! important][COLOR=green ! important]saved[/COLOR][/COLOR] on this computer do not match the requirements of the network"I have never encotured this kind of problem before. I proceeded to call Comcast who did all kinds of trivial beginner troubleshooting such as restart the router, restart the modem turn on and off the computer.
View 3 Replies
View Related
Oct 10, 2011
I 've got some problem with my Mail Server since I've migrated to an ASA5510.Actually the server is in a DMZ with a private Ip ( 10.x.x.2) and it is translated to a Public IP ( 194.x.x.65).Some Users received in there mailbox a system administor error message :Object : Impossible to deliver : testYour message could not be deliver to one or more of its recipients: 421 SMTP connection went away!When they try to re sent it some times later, message is sent whithout problem.
View 3 Replies
View Related
Aug 28, 2012
I have 2 datacenters running same equipement (two Nexu 5596 with FEX).I just took a look at the log just to see if everything is ok and I saw that I have the same error message (a lot of times) at both location :
%SYSMGR-FEX100-5-HEARTBEAT_LOSS: Service "satctrl" heartbeat loss 2 ,max 7,I though it was a problem with my peerklink-keepalive connection but I see the word FEX ....so i'm not sure...
Note that at both locations, my Nexus are connected back to back through the management port using transceivers. So it's a copper cable from the first nexus, going into a transceiver, going to another transceiver in fiber and then back to copper to the other nexus.
View 2 Replies
View Related
Mar 4, 2012
Just bought first wireless router, when i insert CD and start setup, after a few seconds i get Error 301: internal error. i have rebooted and still no luck. I've tried going to 192.168.1.1, i got in one time but didn't understand half the stuff. now i can't go back into that page.
View 8 Replies
View Related
Feb 21, 2011
We find ourselves in a difficult situation with the Cisco VPN Client version 5.0.07.0290 where it keeps giving us an
"Error 42: Unable to create certificate enrollment request"
When we attempt to use the Online enrollment method to create and enroll a new certificate. There is no additional information in the VPN client logs where we have set 3-High for all logs. In addition, Wire shark does not show any packets sent from the machine running the client to the Cisco 3825 router which runs the Cisco CA.
To create and enroll a certificate we do the following:
1. Click on the Enroll button to show the Certificate Enrollment dialog
2. Select Online
3. Select <New> for Certificate Authority
4. Enter http://192.168.120.1 as CA URL (note, 192.168.120.1 is the IP of the Cisco 3825)
5. Click Next to display the dialog where we can enter certificate details
6. Enter details in all fields except IP Address and Domain
7. Click Enroll which shows a dialog with the Error 42 ... message in it.
If we attempt to create a request by using the File method, all works fine, that is, the client creates a file with the enrollment request. The fact that the client does not send any messages to the Cisco CA leads us to believe that we have a problem on the client machine. However, the client does not write any information in the logs, so it is a bit hard to fix the problem. I can provide additional configuration information if required for both the client and the Cisco CA. Note that we have not modified any client configuration. Basically, we installed the client on a Windows 7 64bit machine and attempted the steps listed above.
View 2 Replies
View Related
Jan 30, 2012
Trying to connect two systems together but was giving error that contact network administrator,one system is laptop with wireless and other is desktop but connect through cable but running windows XPSamson
View 1 Replies
View Related
Mar 19, 2013
I bought belkin N150 recently. I tried to configure with my ISP. They are surprised how I don't have DHCP option in the wifi configuration and asked me to upgrade my firmware. When I tried to upgrade. I downloaded the firmware from [URL] tried to upgrade. It is showing file format error.
View 2 Replies
View Related
Apr 5, 2012
I have tried Intel tools and latest drivers ( w/ and w/o pro wireless utility) but cannot pass thru code 10 error. Tried uninstall and install....as earlier card 4965 agn worked fine but seems like some conflict is stopping successful 5300 agn driver install.
View 20 Replies
View Related
Feb 15, 2012
We have a Cisco 2851 router that crashes every night. Below is the 'show log' output. The provider is telling us that it is our equipment. We have replaced the router and still have the same problem. Is it our equipment or the provider?
Feb 15 19:29:43: %BGP-5-ADJCHANGE: neighbor x.x.x.x Down Interface flap
Feb 15 19:29:43: %BGP_SESSION-5-ADJCHANGE: neighbor x.x.x.x IPv4 Unicast topology base removed from session Interface flap
Feb 15 19:29:44: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0/0:0, changed state to down
Feb 15 22:34:13: %CONTROLLER-5-UPDOWN: Controller T1 0/0/0, changed state to down (LOS detected)
Feb 15 22:34:15: %LINK-3-UPDOWN: Interface Serial0/0/0:0, changed state to down
View 6 Replies
View Related
Dec 20, 2011
We want to get MIB files for snmp v2 from Cisco 2851 Router running with IOS below,
c2800nm-advsecurityk9-mz.124-15.T7.bin
View 1 Replies
View Related
Jan 31, 2012
We have Cisco router 2851 and asa firewall. We configured on he router for IP phones and ISP connected. The ISP directly connected on the router and asa firewall connected to the router. We have plan to configure VPN on the router. We have available public ip address. if i configure the VPN on the firewall we need to configure firewall local ip address to public ip address. SO how to configure firewall local ip to public ip ? Where we can configure , mean on the router or firewall. Firewall and router configuration.
View 11 Replies
View Related
Aug 29, 2010
I have a Cisco 2851 (c2800nm-advipservicesk9-mz.124-25d.bin) Router configured with one site-to-site vpn. Is it possible to configure a failover vpn tunnel on this router?
View 8 Replies
View Related
Oct 14, 2012
I have an office with 50 users. I have both a 2851 and a 2921 available. Which one would be a better fit?
Comparativley, which is the more powerful unit?
View 3 Replies
View Related
Feb 16, 2012
Do I need to obtain license keys/files when upgrading a 2851 to IOS 15.x? I'm getting a bit confused seeing the documentation that says 1) IOS has gone to a universal image and 2) that feature sets are unlocked based on the installed license.
I was able to download a feature specific IOS image for the 2851 and it did not bother me about licensing upon boot up.
I read one post on here that stated 2800/3800 series (G1) do not have to worry about the licensing piece and that it's just 2900/3900 series (G2) hardware that require it.
View 4 Replies
View Related
Jan 23, 2013
Is the 2851 router meet these requirements ? if no. What is the must specific series of the routers suitable for this requirement:
1. Comprehensive interface range supporting T1/E1, NxT1/E1, FE, and High-Speed WAN .
2. Wide array of Layer 2 access protocols including Frame Relay, Ethernet, and PPP/HDLC .
3. Rich and granular QOS and instrumentation for prioritizing mission-critical traffic such as voice .
4. A modular platform with a broad range of interface options.
5. Network Address Translation (NAT), and IP Sec .
6. Four (4) auto sensing LAN Ports (10/100/1000) Mbps built-in routed ports.
7. WAN Interface Slots (4-6 option Slots) .
8. WAN Interface Modules (2xT1/2xE1/2xSerial/2xFE/DS3).
9. Memory (512/1024 MB DRAM) .
10. Built in redundancy (Power Supply) .
11. Two (2) Integrated GE ports with copper and fiber support .
12. Support for a Small form-Factor Plugged ( SFP) port for GE.
13. Support Network Timing Protocol (NTP).
14. Security: On-board encryption Support of up to 2500 VPN tunnels with the AIM-HPII-PLUS Module Antivirus defense support through Network Admission Control (NAC) many more essential security features .
15. Voice : Optional support for Survivable Remote Site Telephony support for local call processing in small enterprise branch offices for up to 240 IP phones.
16. Performance : Up to 1GB DRAM Up to 1GB Flash The maximum transmission unit (MTU) Up to 9576 bytes Throughput up to 1.2 Gbit/s .
17. 110/220 volts.
18. Warranty certified by Sis 98 or by OEM (original equipment manufacturer) .
19. Up to 115.2 Kbps for Console/Aux port with DDR capability.
20. Supports IPv6
View 2 Replies
View Related
Oct 31, 2012
I seem to be having an issue getting a 3xT1 bonded solution to work. I can get 2 out of the 3 T1s to come up and pass traffic, but I can not get the third one to be added to the solution.
Hardware: 2851
IOS: c2800nm-advipservicesk9-mz.124-15.T8.bin
Modules:
NAME: "VWIC2-2MFT-T1/E1 - 2-Port RJ-48 Multiflex Trunk - T1/E1 on Slot 0 SubSlot 0", DESCR: "VWIC2-2MFT-T1/E1 - 2-Port RJ-48 Multiflex Trunk - T1/E1"
PID: VWIC2-2MFT-T1/E1 , VID: V01 ,
[Code]....
View 4 Replies
View Related
Mar 29, 2012
I have a Cisco 2851 (with a 4 port switch module) that I am trying to set up with two different internet connections, and have it route traffic out to them based on the source IP. One connection is a 50mb Comcast connection, another is our T1 that our servers are hosted on. The goal is to guide server/phone system traffic to the T1 and have the rest default to the Comcast. I currently have the 2851 connected to our Layer 3 switch (Dell Powerconnect 6224) with a subnet created between them. Static routes have been created on the 2851 back to all of our existing subnets. Traffic flows internally without a problem between the subnets and 2851 (and vice versa). I set up the 2851 with route-map's in the NAT to control the flow of traffic, with the default route set to the Comcast connection. Default route works great, speedtest shows full speeds and everything looks great. The problem happens when I apply my route-map policy to the internal LAN interface with the ACL list of IP's that I want to guide to the T1 (with a next-hop of the T1's IP address). I tested some tracert's and pings from one of the IP's in this list and they would stop at the T1 modem and not go any further. I did a "show ip nat translations" and noticed that the "outside" portion (right half) was blank for every IP that was in the ACL or related to the T1. So my guess is it looks like this is not doing NAT for the T1? I double-checked that I had my "ip nat inside" on the LAN interface and "ip nat ouside" on the T1 VLAN interface and Comcast interface and they were there.
View 6 Replies
View Related
Nov 15, 2012
I am using a 2851 router in mpls network. We had a power shut down activity recently and post to that i could not find any logs in the router.
View 4 Replies
View Related
Jun 11, 2013
I am trying to find information on what the max clock rate supported on WIC-2T on a Cisco 2851 and Cisco 3845 Routers.
View 1 Replies
View Related
