I have a WiFi printer connected to an CWAPP Cisco AP AP1250. I am using WPA2-PSK to connect to this AP. I find that the printer connects to the AP at times and at times it does not. I got an error message from the Capture an error on the backend controller of the network."Authentication Request received invalid RSN IE Mismatch WP2 algorithm"
View 3 Repliesi was giving a laptop it has links on it and added belkin on it because that what my other pc have but it not letting me connect .I went to add and remove programs but links was not on it .i have tried repairing my ip adrress n turnng it on n off but nothing . belkin is showing excellent signal n it worked at the prvious owner house .
View 1 Replies View RelatedI have a L2L IPSEC tunnel between a set of failover pair of two ASA5510's and a single ASA5505. Over time they will loose connectivity through the tunnel. The tunnel itself stays up, but cannot pass any traffic.When looking at the tunnel I always see this on the set of 5510's (marked in bold @ IPSEC ID 3)?
View 5 Replies View RelatedUp to today I used Verizoon 4G to a Windows Visata box running Internet connection Sharing to get my home lab connected to the Internet . All was working well.
Today I had Hughesnet come and installl their service and I can no longer get access to the Internet from my PC netowrk. my VPN to my office for my IP phone coomes up an works just fine. At the router I do have Internet access which then leads me to believe that my problem is NAT related.
My router is a 2851.
When I enter PING 4.2.2.2 I get !!!!! but when i enter PING 4.2.2.2 SOURCE 192.168.69.3 I get .....
Here is my config info:
crypto isakmp policy 1
encr 3des
hash md5(code)
I had been working on our client servers through Cisco VPN using internet datacard. But from past 3 weeks after logging into Cisco VPN using my username/password, when I try to connect to any of the servers, it is giving connection timed out error.
Whereas, my team members across other locations are able to connect to the servers using my VPN username/password.
I thought there might be some issue with my laptop or internet datacard. I got my laptop formatted, even tried out with fresh new laptops & new internet datacards, but the issue remains same.
I have tried using vpn_5.0.06.0160-k9 & vpnclient-5.0.05.0290-k9 to connect but issue did not get resolved.
i m trying to connect two routers a Cisco DPC3825 (r1) and DIR-655 (r2) and at the end getting the error. i have disabled the SPI firewall on r1 and connected an ethernet cable lan to lan between the two. i don't want to confuse with whatever the mess i have done previously,Tell step by step what i should do to connect these two routers.PS: in addition, the gateway ip of r1 is 192.168.0.1 with subnet mask of 255.255.254.0 and the gateway ip of r2 is 192.168.0.2 with subnet mask of 255.255.255.0. r1 has a ip range of 192.168.0.10 to 192.168.0.128 while r2 has range of 192.168.0.100 to 192.168.0.199.
View 7 Replies View RelatedAfter a successfull installation of NCS 1.2 into a vmware environment and run the setup I have the following error while trying to start or to have a status for NCS (ncs start ot ncs status):sh: /opt/CSCOlumos/bin/wcsadmin.sh No such file or directory
View 10 Replies View RelatedI have one 5500 and about 15 Cisco 3502 APs.
The problem is that one of the clients loses the connection to the network time to time ,The error in the WLC logg is
*Dot1x_NW_MsgTask_0: Jul 06 17:42:38.934: %DOT1X-3-INVALID_WPA_KEY_MSG_STATE: 1x_eapkey.c:843 Received EAPOL-key M2 msg has invalid information when mobile is in START state - invalid secure bit; KeyLen 24, Key type 1, client 00:21:6a:af:be:70
I am currently on Time Warner Cable 10 mbps packge, and am using their wireless DOCIS3 modem/router. It is connected in my bedroom to the main computer. That computer stays connected. However, throughout the rest of the house (we have a two story townhome) it will drop completely or give limited connection...constantly. Sometimes I can have my laptop next to me and it will go out or give limited connection. The connection speed never drops, it just goes completely to no connection. Not for sure what is going on, if its on my end or time warner. Has been doing this for quite some time, the cable company comes out and changes the modem, but that's it, couple days later, goes back to doing it again.
View 8 Replies View RelatedI have an 1841 that was working fine - I could SSH to it with my Radius login and console into it with local credentials ("Fred").I added another use ("Mike") with priv 15 so the end user could log in locally via console if needed.After that, we can both log in via console, but when we try to enter privileged mode we get "% Error in Authentication", before even entering the password.I can still log in via Radius SSH with no problems and access privilege mode via SSH.What am I missing so we can have two different users be able to log in locally with different credentials and access privileged mode, and keep my ssh radius working?
View 3 Replies View RelatedWe're seeing "OutDiscard" error on a LAN switch connected to newly migrated Cisco IP phones. All the other error counters are clean except for the OutDiscard. (please see attached "show int count err" output.) [URL].
According to the link above, the common cause of such discards can be to free up buffer space.(Am I seeing a switch buffer issue?) How to identify/resolve the cause of the OutDiscard.The switch is 3750-E running c3750e-universalk9-mz.122-44.SE6.bin
I was using my internet on my Acer Windows 7 operating system wireless just fine on Monday. I tried to use it on Tuesday and could not connect to the internet wireless any longer. I get an error message next to my network stating ""The settings [COLOR=green ! important][COLOR=green ! important]saved[/COLOR][/COLOR] on this computer do not match the requirements of the network"I have never encotured this kind of problem before. I proceeded to call Comcast who did all kinds of trivial beginner troubleshooting such as restart the router, restart the modem turn on and off the computer.
View 3 Replies View RelatedI 've got some problem with my Mail Server since I've migrated to an ASA5510.Actually the server is in a DMZ with a private Ip ( 10.x.x.2) and it is translated to a Public IP ( 194.x.x.65).Some Users received in there mailbox a system administor error message :Object : Impossible to deliver : testYour message could not be deliver to one or more of its recipients: 421 SMTP connection went away!When they try to re sent it some times later, message is sent whithout problem.
View 3 Replies View RelatedI have 2 datacenters running same equipement (two Nexu 5596 with FEX).I just took a look at the log just to see if everything is ok and I saw that I have the same error message (a lot of times) at both location :
%SYSMGR-FEX100-5-HEARTBEAT_LOSS: Service "satctrl" heartbeat loss 2 ,max 7,I though it was a problem with my peerklink-keepalive connection but I see the word FEX ....so i'm not sure...
Note that at both locations, my Nexus are connected back to back through the management port using transceivers. So it's a copper cable from the first nexus, going into a transceiver, going to another transceiver in fiber and then back to copper to the other nexus.
Just bought first wireless router, when i insert CD and start setup, after a few seconds i get Error 301: internal error. i have rebooted and still no luck. I've tried going to 192.168.1.1, i got in one time but didn't understand half the stuff. now i can't go back into that page.
View 8 Replies View RelatedWe find ourselves in a difficult situation with the Cisco VPN Client version 5.0.07.0290 where it keeps giving us an
"Error 42: Unable to create certificate enrollment request"
When we attempt to use the Online enrollment method to create and enroll a new certificate. There is no additional information in the VPN client logs where we have set 3-High for all logs. In addition, Wire shark does not show any packets sent from the machine running the client to the Cisco 3825 router which runs the Cisco CA.
To create and enroll a certificate we do the following:
1. Click on the Enroll button to show the Certificate Enrollment dialog
2. Select Online
3. Select <New> for Certificate Authority
4. Enter http://192.168.120.1 as CA URL (note, 192.168.120.1 is the IP of the Cisco 3825)
5. Click Next to display the dialog where we can enter certificate details
6. Enter details in all fields except IP Address and Domain
7. Click Enroll which shows a dialog with the Error 42 ... message in it.
If we attempt to create a request by using the File method, all works fine, that is, the client creates a file with the enrollment request. The fact that the client does not send any messages to the Cisco CA leads us to believe that we have a problem on the client machine. However, the client does not write any information in the logs, so it is a bit hard to fix the problem. I can provide additional configuration information if required for both the client and the Cisco CA. Note that we have not modified any client configuration. Basically, we installed the client on a Windows 7 64bit machine and attempted the steps listed above.
Trying to connect two systems together but was giving error that contact network administrator,one system is laptop with wireless and other is desktop but connect through cable but running windows XPSamson
View 1 Replies View RelatedI bought belkin N150 recently. I tried to configure with my ISP. They are surprised how I don't have DHCP option in the wifi configuration and asked me to upgrade my firmware. When I tried to upgrade. I downloaded the firmware from [URL] tried to upgrade. It is showing file format error.
View 2 Replies View RelatedI have tried Intel tools and latest drivers ( w/ and w/o pro wireless utility) but cannot pass thru code 10 error. Tried uninstall and install....as earlier card 4965 agn worked fine but seems like some conflict is stopping successful 5300 agn driver install.
View 20 Replies View RelatedI assume that the E4200 uses VLANs for the the guest network. Is it possible to trunk the LAN interface and pass that vlan to the switch so that you can pass the vlan to an AP?Would be great to see the Guest wireless on the Cisco 1250 like I do the main SSID.
View 5 Replies View RelatedMy desktop is fitted with a Belkin 54G PCI card which I have never had problems with before. My desktop is in the basement and due to poor signal issues another router has been set up in the basement. I had to constantly repair the connection to the previous wireless network but even though the signal is much stonger with the new router and network I am having even more issues with not only having a repair the local only connection issues but also with 'limited connectivity' and the only way to resolve it is to restart my computer.
View 3 Replies View RelatedOur building used to have a very old server that basically just served as a place for teachers to store files and not much else. We have just changed ISPs and decided that we no longer needed the server at all. I disconnected the server from the network and replaced the old ISP's modem with the new ISP's modem. At first, everything seemed OK. My computer and several other teachers' connected to the Internet with no problem. However, some of the computers in the building could not connect. We get error messages with "limited or no connectivity." Part of me thought that perhaps the connections themselves are bad. However, when I take my laptop to classrooms with trouble connecting - mine connects easily using their cables. If I move their computers to my room, their laptops still won't connect. I have put my computer side-by-side with another one to make sure the settings were the same (auto-detect IP, DNS, etc.) and can't find differences. This problems is affecting our Windows 7, Vista, and XP computers the same.
View 11 Replies View RelatedI started having this stupid problem after i built my first computer, in my old computer it was all fine, am using an ethernet cable between my pc and laptop, it is crossed or whatever its called, when i plug it in it gievs me an error, limited connection or no connectivity which pisses me off, i have all the drivers installed everything is up to date.. sometimes it connects, but after 10 mins it disconnects again, and sometimes it works fine until i reboot my pc..
View 17 Replies View RelatedI just got a used Acer AspireOne AOA150 ZG5 Netbook and upon bringing it home, I received a "Limited or No Connectivity" error when attempting to use the internet via wireless. I have another laptop that connects at the same time with no issues. The Netbook DOES work if I hardwire into my home router. I have since taken the Netbook to work and it connects to the wireless there with no issues. So it seems to be an issue specifically with my home router/modem and this Netbook.So far I have flushed my DNS cache, done the Winsock and reset my TCP/IP, removed wireless profiles, and tried the Repair function.None of that has worked. My wireless properties are also set to automatically obtain the IP address.I'm on XP SP3 and it seems like a lot of folks think that it's a SP3 issue, but I don't think so in my case since the wireless is fine in other locations. [code]
View 13 Replies View RelatedI have gone into the router itself at 192.168.1.1, changed settings, reset settings, upgraded firmware to 1.0.04, and / or whatever else was posted by other users. I have also changed my settings for my lappy's networking adapter, re-edited my IP, removed / reinstalled network adapter, and / or whatever else I found to try to do. I am frustrated and upset that a wireless problem is giving me so much headache.I am running Vista 32 Home Premium, HP Pavillion dv6700 Notebook, with a Cisco Linksys E2000 Wireless N Router. I have connected a desktop via wireless USB adapter, my android phone, my GF's android phone, her kids iTouch and phones, and when I try to connect via wirelessly to the router, I get local access only with an unidentifiable network, which then limits my access online, (I cannot connect to the internet). It will let me get online via ethernet cable, but not wirelessly. I have bypassed the router and connected directly to the modem without any problems. I have reset the modem and router many times, as well as rebooted my laptop a lot trying to gain some connection. My laptop can connect to other wireless hotspots / access points without any problems.
View 1 Replies View RelatedI'm still having bad time with the basic configuration I'm trying to make 2 VLANS: voice and data and run DHCP server on router hoping it will give the Ip Phone an IP address but I don't know where the problem is.
View 4 Replies View RelatedIs there a way to get VPN IP address without giving someone access to the firewall itself? LIke a script you can put on a website?
View 2 Replies View Relatedi have a cisco router that has dhcp configured, the router ip address is 10.10.10.***. all computer that attached to the router are using static ip and works fine but when i am connecting my laptop using wireless in gets an 192.168.1.*** address.
View 17 Replies View RelatedI have a T1 connection to one of my sites, I am running HREAP with 4 AP's. I have been noticing a spike in traffic from my AP's to the WLC. Even when no one is on the wireless. When you use encryption (DTLS) should this cause spikes on the T1 ?
View 2 Replies View RelatedSG300-10 mode:layer 3
dns server:192.168.2.11
vlan1 192.168.2.0 ip:192.168.2.254 0.0.0.0 next hop 192.168.2.3
vlan2 192.168.50.0 ip:192.168.50.254
dns server table:192.168.2.11 (active)
Router(192.168.2.3) dst.address 192.168.50.0/24 gw:192.168.2.254
No internet
pc:
ip:192.168.50.10 192.168.2.10
gw:192.168.50.254 192.168.2.254
dns:192.168.50.254 192.168.2.254
If dns = 192.168.2.3 >> yes internet
I think there is something wrong with the DNS setting on the SG300?Or I do something wrong?
I am trying to give a vendor VPN access so that they can remotely monitor and diagnose their installed heating and cooling equipment. I dont know where to start and I apologize in advance for my ignorance. I am technically savvy but i have no Cisco knowledge base.
It is a PIX 506e firewall with PIX v6.3.
Not sure if this belongs here on in a different section. We are in the process of purchasing a new ACS 5.x appliance. I would like to take a look at implementing WPA2 Enterprise with our Cisco APs.
View 4 Replies View RelatedThe Internet on my Toshiba laptop suddenly has stopped working. If I connect the laptop directly to the router the internet works ok. Othe computers work ok using the same router.
View 1 Replies View Related