I assume that the E4200 uses VLANs for the the guest network. Is it possible to trunk the LAN interface and pass that vlan to the switch so that you can pass the vlan to an AP?Would be great to see the Guest wireless on the Cisco 1250 like I do the main SSID.
View 5 Replies
I have a E4200v2 i also have a Airport Extreme I want to use this to extend my wireless range in my house? I've played around a little tring to configure the Airport extreme but can't seem to get it to connect to my E4200v2? Can you mod the Airprt Extreme with dd-wrt or something that might unlock some of the features?I can't stand the interface. The E4200v2 is brand new.
View 1 Replies View RelatedWe have an E4200, currently with wireless disabled, on a Windows 2003 based domain. We have a Static IP from our ISP.We want to install some wireless & wired security cameras (IP-based) so that we can view them from our iphones or droids outside the network. The software for these cameras will reside on a computer that is not currently on the network, but needs to use the same Internet connection as the current domain. We basically want to separate these cameras & computer from the current network, use same Internet connection (& Static IP), and enable wireless on the E4200 for the cameras only.
View 9 Replies View RelatedI have two WRT54GS routers. I want to extend my WiFi from the router connected to my upstream in the office to a second router in the living room. I want devices configured for the SSID and passphrase of my current WiFi (which is find in the office) to work seamlessly in the living room. I understand I can do this by running a cable and configuring router 2 as a client of router 1 with router 2 exposing the same SSID and passthrase on a different channel.
But I really don't want to run a cable.There is a point where a client can see router 1 where an AP would cover the living room.
Can I put router 2 at that point, have it connect wirelessly as a client to router 1, and have it expose as an AP using the same SSID and passphrase? Can this be done without wiring the router?
Is there any way to make networks hidden through the WiFi Smart software? I have a Cisco Linksys E4200V2. I have gone through everything to try figure out how to make my S.S.I.D. to not be broadcasted, but seems like the only way to make it hidden is to use the Origonal Firmware make it as hidden, then install the New Firmware and software. Seems like Cisco may have missed this option. I do know a lot of people would prefer their Networks hidden for a little security. I know it isn't much, cause if someone wants to get that info it's not hard to get it. But for people who don't know or don't want to waste all the time to find the Hidden Network name can be turned away, for going through that extra step.
View 6 Replies View RelatedI have a non linksys modem router with wifi capabilities.I want to connect wirelessly the E4200 with my modem/ router ... After that, I want to be connected ONLY to the E4200, wirelessly and wired TOGETHER to have internet to my desktop pc (via lan cable) and to my wireless clients (via wifi).
View 6 Replies View RelatedIt would be nice if there was a "Note" field next to each MAC field whereby you could specify what device the MAC belongs to. I have quite a few listed but recently I've gotten rid of the devices. I have to go through all my current devices, not them in another program, and then remove the ones that are no longer needed.
The Wireless Client List doesn't capture all the names so that's not what I'm looking for.
Also, it would be great if the "Note" would tie into the Parental Controls so that I know exactly what device I'm choosing. It currently lets you select from the Wireless Client List, but the list doesn't have all the Client Names populated.
So, one, is this feature available (or something similar) and two, if not, please take this into consideration as a useful feature for a new version down the road.
My e4200 v2 arrived today to replace my v1. I installed it along with a re1000 range expander for our big home. Works pretty well now, but did some google searching and it seems i could make my original e4200 into a bridge, would this be the way to go for max wifi? I could run a cat 6 cable upstairs along the outside of the home fairly easily.
View 9 Replies View Relatedwell, i just bought an E4200 and, by the way, was very hard to configurate. But the real problem is: if there is a power loss, both modem and e4200 lights up, but no internet connection is provided.Even the SSID desappear. I trried to disconnected everything, reconnect by parts, but no success.I wired connect the E4200 to my iMac and the router was ok, configurated.Then, i reconnect to the modem and all worked ok.Now im testing possibilities and is i reboot the router, the net desappear and i have to try possibilities till it works.
My older router connected automatically, without a problem, but i decide to buy "the best" brand and its top product". Now im disappointed..
Twice i realize that if the connections drops out, i have to disconnect and reconnect the internet cable from my E4200...
I am having a trouble with my router, our modem is the one that is connected to a TV box and it comes with a wifi function(a modem with a wifi function). I am not sure how to set it up, so I connected it to E4200 which is located in another room using CAT6 flat cable and set it to "Bridge mode". But whenever I open the TV box, the wifi won't work, and when it's closed, it works. :s how weird is that. Are there any problems? The modem with wifi will always work either way I open/close the TV box, but the E4200 wifi will only work when I close the TV box. I asked my service provider about this and they tell me it's not their problem anymore.
View 2 Replies View RelatedI just purchased an e4200 in a corporate environment where we already have a wireless router. I am not able to connect the 2 devices via a LAN cable and am wondering if I can get bridge mode working over the network (wireless). I set the Linksys to bridge mode and assigned it an ip address. I disabled all wireless settings, etc. I then connected the internet port of the Linksys into a data port (wall jack) that connects to our flat network switch. It says it's connected under "Status" but I'm not sure how to confirm this.
View 3 Replies View RelatedI recently bought an E4200 and noticed that the wireless speed keeps dropping as it stays connected.As soon as I power it on, my iPhone and notebook connect at 54Mb, but as they remain connected, the speed keeps dropping to 48, 36 and one morning, my phone was oscillating between 5 and 11. The iPhone was almost at the same spot, and the signal was around 85~95%. On my 3 year old DIR-300, the speed don't change at all, and it's in a place where I can see around 15 connections. On the E4200 I can only see 2 other networks.I've already tried switching channels, fixed and auto channel, updating firmware and a few other common configurations. At first, I thought it was my repeater, but I turned it off and it didn't work. Turn my cordless phone off didn't change it also.
View 3 Replies View RelatedI just got an e4200 and I'm haviong very disappointing wireless speeds. My network is setup as follows
powerline----------desktop
|
|
powerline-----------wireless router ----------- laptop (using USB adapter Linksys AES1000, Intel bng internal, Belkin adapter)
If I plug into the back of the e4200 I can download at roughly the raw speed of the powerline 7 MBps. So I know the powerline connection is just fine and the routing function of the e4200 is just fine. When I use my laptop my speeds are wildly variable on both 2.4 and 5 ghz. With a clear line of sight to the router (maybe 7 feet away) they seem to hover around 1.5 MBps but have reached as high as 5.5 MBps twice. Using my much cheap older Buffalo router I routinely get speeds in the 4.5 MBps range which I would consider acceptable (although it has other, separate issues). I have followed all of the advice I can find on the forums. The range is also pretty terrible. If I'm 20 feet away and no longer have a clear line of site to the router I will frequenly have almost no signal and miserably slow download speeds in the kbps.I have made sure that I am using wpa2 with AES, I have changed my MTU to 1365, I have updated the firmware to the one released in March, and I have explored setting different channels on the router to no avail. I also contacted tech support which I'm only marginally sure understood that I was talking about the LAN connection and not the internet.
Why I must restart my e4200 after 2-3 days when I want to connect my device like notebook or phone to the router. After restart my device can obtain the ip. I hardly to turn off the router.Is something wrong with my router ? [code]
View 2 Replies View RelatedThe task is to share Internet via Wireless router for visitors without any Proxy/Windows Domain authentication.We have:1) Windows based Domain with Active Directory Users, with no DHCP setup, only Static IPs allowed. Used as a DNS server, the IP-address is 192.168.1.1, Domain name, say, Internet Connection via Proxy server which authenticates users via above-mentioned DNS server, the Proxy server IP-address is 192.168.1.3, ruled by MS TMG (ISA server)3) A Wi-Fi Router Cisco E4200.The local area network is wired and works fine. Domain users are happy.The idea is to make visitors happy with a free Internet connection without wiring them into the LAN.So:1) Respected visitors would not have to set up static IP-adresses on their devices to connect to Internet and2) Respected visitors would not have to enter domain credentials to get access to Internet, but3) Network security should not be jeopardized.
View 3 Replies View RelatedI got a problem with my setup main computer, It work wery god wireless, with very fine speed about 82 mbit in and 24 mbit out. The problem is that it almost dont work at all with cable, even if i turn off the wireless network, the speed is about 2-3 mbit in and about 6-7 mbit outAll other computers, tv. printer wireless work very fine.
View 1 Replies View Relatedall other devices have excelent signal
View 5 Replies View RelatedI purchased a WAG320N and E4200 and have manged to get the modem connected to the internet and it's running fine in that respect, with no adjusting done to the settings.My intentions are to connect the WAG320N to the E4200 wirelessly, as they are in seperate rooms in the house and have done a similar setup in the past with a 7300G Billion Modem and WRT54GL.
With the E4200 I quickly discovered there was no bridge mode out of the box, but checking these forums got the indication that the firmware updates added this capability, so updated it..I entered the IP Address of the Router, the Subnet mask of the network and the Default Gateway / Modem router IP address into the fields, following this guide, but have not been able to get the computers to contact one another, nor ping the other devices.
E4200 Version 2.0.37.131047 disconnects my wireless clients intermittently. I am seeing it mostly on the 5Ghz band but that is where most of my clients are connected. I have all the setting in advanced tweaked per cisco best practice. It just seems to reset every so often. Wired connection is not disconnected.
View 9 Replies View RelatedI've got a new E4200 router, Everything works just fine, but I'm unable to ping any WiFi hosts from my LAN, I can ping LAN from any WiFi Host.If I disable NAT on the E4200 I'm able to ping WiFi hosts but then all WiFi Hosts are unable to talk to the LAN.
LAN - 192.9.209.0
WiFi - 172.16.1.0
Same config runs perfect on my WRTG54GL.
I have the following setup at home:
-E4200 connected via Ethernet cable (100Mbs) to local ISP for internet access
-E4200 connected via Ethernet cable (1Gps) to my desktop PC
-E4200 connected via wireless (5Ghz with WPA2 personal) to my laptop
In general, everything works fine, I can download files from internet to my PC close to the maximum speed limit (80-90Mbs), the wireless connection goes up to 300Mbs and it can achieve around 10-14MB/s file transfer between PC and laptop.A lot of the time the wireless connection to my laptop is used for HD content streaming from the desktop PC. It works very well until I start downloading files to my PC with speed greater than 50Mbs, when the wireless connection speed drops very fast to about 500KB/s which results in interruptions on the video streaming. At the same time the router’s web interface reacts much slower than usual, as if the router’s CPU is overloaded.
I’ve read this follow up review on Small net builder url...and it’s clear that there are some issues when taking E4200 to the limit, but in my case it’s nowhere near that.
How to get WDTV live hub to successfully connect to the E4200 over wifi without getting a DNS error?
My system:
E4200, fw v. 2.1.39.145204
WDTV Live Hum, fw v. 3.08.14
DWA-160 (rev. A) usb wifi dongle fw v. 1.80
My sony wifi equipped blueray connected to the E4200 without trouble and accesses the USB HDD connected to the E4200.
All my wireless devices are 802.11n and none of them can pick up the 5 GHz band on my E4200 router. I've tried all the different settings and channels on this band and still nothing. The only device i have been able to pick up the 5 GHz band with is a Desktop PC with a linksys AE1000 USB network adapter. This is quite frustrating because I would like to put my blu-ray player and game systems on the 5 GHz band. Laptop, PS3, XBOX 360, iPOD, and blue-ray player all can't pick up the 5 GHz band. Either my unit is defective (which I don't think is the case or not even the USB adapter would be picking up the network) or there is something I am missing (which I have tried pretty much everything as far as I know with the settings, have two separate names for the band networks and have tried each individual channel under 5 GHz). Also running current firmware version.
View 9 Replies View RelatedI've got a new E4200 router, Everything works just fine, but I'm unable to ping any WiFi hosts from my LAN, I can ping LAN from any WiFi Host.If I disable NAT on the E4200 I'm able to ping WiFi hosts but then all WiFi Hosts are unable to talk to the LAN.
LAN - 192.9.209.0
WiFi - 172.16.1.0
Same config runs perfect on my WRTG54GL.
I've bought a E4200 router because of it's "maximum performance". With the normal settings i have a wireless range of maximum 10 m in the building. after 5m I've got a low signal.I tested a cheap Netgear-router, which had the same range as the E4200 a 125 Euro.Is my E4200 broke or is it just a bad buy? The settings are standard (that shouldn't be the problem, I guess!?)
View 9 Replies View RelatedI recently bought myself the E4200v1 router, and have had several issues with it. One issue I cannot seem to find a workaround for is the wifi bandwidth problem.I have a 100/10 mbitl internet connection. The router claims to support 300/450 mbit speeds over wifi, so that should be plenty. in reality however, that isnt so.Even though my N-standard wifi adapter on my machine states it has a 130 mbit connection to the router, I consistently test the internet throughput when using wifi and speedtest.net to around 20-21 mbit. If I put in a cable, I instantly get full speed, 100/10 mbit.
Have to add; I am not new to the networking game, I have a CCNA and a degree in computer sciences, and work with hosting web sites using cloud tech every day. At this point, I have tried everything related to settings on the router, so I can only conclude that there's some kind of bug in the firmware. I would expect the standard firmware to work, and not having to install DDWRT or other custom firmware.
My router a E4200. the thing is i want to disable the dhcp services from the router, because there are allready a dhcp server in my network. but if i disable the dhcp will the Guest wifi functions still work?
View 3 Replies View RelatedI have a E4200 v1, connected with a few PCs by ethernet ports and various devices by wifi. Now the wireless devices work perfectly but sometimes the PC via ethernet ports cannot connect to LAN and internet.
View 2 Replies View RelatedI have Linksys configured with IP 192.168.0.x and my local network ip 192.168.1.x have firewall connected to Adtrans box that gives us internet access via T1 line and other port is connected to the switch. Wireless router is connected to the switch using internet port.I can connect to wireless using iphone but emails don't work when connected to wireless. I tried to connect laptop to wireless is does not connect.
View 9 Replies View RelatedI have a E4200 updated to the latest firmware I have problems with the wifi on the 2.4GHz band, in fact, at power on, many times wi-fi on the 2.4GHz band doesn't work but the 5GHz band works normally. After some reboots the wi-fi operating normally on both bands.
View 9 Replies View RelatedThe update "failed," due to an "unexpected error." Wireless connection is disabled, although, as you have probably noticed, I can still connect to the internet (using an ethernet cable from my router to my laptop OSX 10.6.8). Error Code 3018 is unknown to Cisco's website. Or should I just start over with the installation disk for my E4200 router?
View 2 Replies View RelatedI have the wireless guest access set up in my E4200 flash to the latest firmware. When I connect to the wireless guest network it comes up under the 192.168.33.xx IP address. I can connect fine but it never pops up the browser so that you can type in the guest password. I'm running Windows 7 but I've also noticed the exact same problem under XP.The only thing I can guess is the problem is that I have this acting like an access point and all DHCP requests go to my router. I've basically turned off DHCP on this and plugged the network connection into the switch on the back.
View 3 Replies View Related[URL]I have a Linksys E4200, even if i put wireless on manual WPS is still working, any answer from Linksys?
View 5 Replies View Related
