I have a E4200 updated to the latest firmware I have problems with the wifi on the 2.4GHz band, in fact, at power on, many times wi-fi on the 2.4GHz band doesn't work but the 5GHz band works normally. After some reboots the wi-fi operating normally on both bands.
View 9 Replies
I installed an E4200 in an outdoor patio area where the ambient temperature can be high (Las Vegas area); however, the router is located in the shade without any direct exposure to the sun. After using the router for about 15 minutes, the router is extremely hot and 2.4GHz band will stop working. In addition, even when the router is working, the 5 GHz band connects at much higher speed than the 2.4 Ghz band. The internet download speed is much higher using 5 GHz compared to 2.4 Ghz.
View 9 Replies View RelatedOn my new E4200, I cannot connect wirelessly to the 2.4GHZ band. I can only connect to the 5GHZ band. I know its not the distance because i've got my laptop only 2 feet away. I've hit the refresh wireless network button, but the only network visible is my 5GHZ. I've also restarted the router, no luck
I went into the router settings and made sure that BOTH SSID'S are broadcasting a signal.and are enabled (ive got the channel and other settings set to auto). I'm able to connect perfectly well to the 5GH band, and walk around the house, but nothing i've done, allows me to see the 2.4GHZ band? So far, my wireless reception is poorer than my old wrt310n.
Connected to time warner we have a belkin 2.4ghz 802.11g g-router. The internet on the main desktop is on and used constantly all day, with 2 laptops and ipad used intermittently. Constantly thorughout the day the internet freezes up and has to be unplugged and restarted though there is no pattern to the freeze, perhaps only be the main desktop may be in use alone, perhaps all the above may be in use. Should I upgrade service from time warner or upgrade my older router.
View 1 Replies View RelatedAll my wireless devices are 802.11n and none of them can pick up the 5 GHz band on my E4200 router. I've tried all the different settings and channels on this band and still nothing. The only device i have been able to pick up the 5 GHz band with is a Desktop PC with a linksys AE1000 USB network adapter. This is quite frustrating because I would like to put my blu-ray player and game systems on the 5 GHz band. Laptop, PS3, XBOX 360, iPOD, and blue-ray player all can't pick up the 5 GHz band. Either my unit is defective (which I don't think is the case or not even the USB adapter would be picking up the network) or there is something I am missing (which I have tried pretty much everything as far as I know with the settings, have two separate names for the band networks and have tried each individual channel under 5 GHz). Also running current firmware version.
View 9 Replies View RelatedRegion : Australia
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 3.13.23 Build 121225 Rel.37950n
ISP : Optus
I note that my 4300 never uses two channels in 2.4 GHz wireless n mode as reported by Inssider. I can see a few other routers on Inssider, one of which uses channel 11+7 ALL the time, though it's not a TP-Link router. Mine sometimes will connect to two channels, thus enabling 300 Mbps, but then quickly drops to 1 channel. I believe this is a firmware fault as I only have 3 or 4 routers in the area of my house and I can't believe this would generate sufficient interference to force the router to run at a lower speed. If the router does behave this way by design, then TP-Link should stop advertising it as a 300 Mbps router as it will almost never operate at that speed.
I purchased a e4200 in hopes that its dual band capability would allow us to run a 2.4ghz network for certain devices and a 5ghz for everyone else. I am able to setup the router and connect but it seems when the 2.4ghz network drops the router drops all connections.
At first I had the networks setup with the same ssid, then changed the 5ghz network to a new ssid but was still losing connection when the 2.4ghz network dropped. This may be a simple routing issue i am overlooking (bit of a network newbie).
Both use the same encryption (WPA2-Personal), same channel and they are tested in the same location with g-only mode. Only one router is switched on at any one time during the test. When 3 g-client notebooks (of various brands) are associated with the E4200, the signal indicator is a single bar, wherelse they can get 3 bars with the WRT54G (in the same location). For Internet speed test on a 20Mbps link, WRT54G is able to substain about 10Mbps, but only 1-2Mbps with the E4200.
Is such difference in performance between the two router models normal? Is there any configuration required to tweak the E4200? Or is it a hardware related issue with E4200?
The E4200 has been updated with the latest available firmware as of yesterday.
Using firmware 1.0.01, has anyone successfully gotten the E4200 to bond two channels using the 2.4GHz spectrum? I just can't get it to bond. I assume it's a firmware issue, yet to be fixed. I've tried settings Auto (20 or 40), and nada. It has never bonded. The 5 GHz bonds fine. There are a few interferences by the neighbours wifi, but nothing substantial that should prevent bonding. I have this router at school too, and the same thing happens there, with the same firmware, so I doubt it's an interference issue. I'm using WPA2 Personal encryption. I tried auto channel, and setting channels to 1, 3, 5, and 11, nothing changed.
I know I'm not bonded because A. Max link speed is ~144Mbps, and B. using a program like inSSIDer tells me I'm only using one channel on the 2.4Ghz spec.
2 days ago my e1000 died, so I went big and bought the e4200 (due to newness, its already loaded with Firmware 1.0.03 build 14) to aleviate my networking woes. I'm running into an issue where I'm utilizing both the 2.4Ghz bands and the 5Ghz band. My desktop as an AE1000, and I'm utilizing that on the 5Ghz band. Everything else in the house (Dell laptop, 2x iPhone 4 and an HP printer) are all connecting to the network wirelessly.
I have had 0 network issues with regards to my wired connections, or my 5Ghz connection. But my 2.4Ghz connection will continuously be unavailable. I have both bands set to brodcast, they have different names so my AE1000 can connect via 5Ghz band. Both yesterday evening, and this morning, my phones, laptop and printer cannot connect, and for the most part, the network doesn't show up on available networks. When it does show up, the devices can't connect.I'm proficient enough to do the general home networking, but I'm at a loss as to how to fix this, without a daily reboot of the router (which seems excessive and unwarranted for a 2 day old e4200 [or any router to be honest]).
Region : Germany
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : newest
ISP : CS
the router lost Wifi signal 5-10 times per day.Router and devices are in the same room. max 4 meters.
I am having a trouble with my router, our modem is the one that is connected to a TV box and it comes with a wifi function(a modem with a wifi function). I am not sure how to set it up, so I connected it to E4200 which is located in another room using CAT6 flat cable and set it to "Bridge mode". But whenever I open the TV box, the wifi won't work, and when it's closed, it works. :s how weird is that. Are there any problems? The modem with wifi will always work either way I open/close the TV box, but the E4200 wifi will only work when I close the TV box. I asked my service provider about this and they tell me it's not their problem anymore.
View 2 Replies View RelatedMy 2.4 GHz is not working corrently on my EA3500 router. I have no trouble with my 5 GHz which I am currently on. On my iPhone I have to manually click the network even though it is known and then the wifi icon lights up full then goes dim then just flashes til it gives up. If I try connecting with my computer it just doesn't load the internet.
View 4 Replies View Relatedmy E4200 is dropping connections several times a day. I'd be working on my laptop, go to a webpage and bang, no connection. A minute or so later it would reconnect. It even appears to be doing this with a computer that is hardwired to one of the ports. So it doesn't seem limited to just wireless. Happens to both N and g channels as well.
View 9 Replies View RelatedI check all of the settings and changed the channel to see if it works. For some reason it disconnects my wireless internet at random times and i know before it never use to do that before with a older router. There is nothing blocking it, it worked before, and my computers can connect except two. The only thing i can guess is my wireless card.
View 6 Replies View RelatedI am now on my second E4200... But still the same failure.. It looses the internet connection 5-6 times a day, and then I have to switch it off and on to get connection again.
View 9 Replies View RelatedI started using E4200 few months ago. It used to have frequent disconnection with E4200 when it's running on router mode back then. After playing with the MTU from 1492 (recommended by ISP) to 1364, it's seems to be quite ok until recently.It is getting worst than before. It disconnect my internet almost few times in 5 minutes.
[CODE]...
Had an E4200 for a couple of months now and have not been able to resolve an issue with the router dropping an Apple iPad 2 at random times.The E4200 is replacing a Cisco Aironet 1200, which never dropped any clients, iPad 2 or others, and never displayed any of the issues below.
TECH DETAILS:The E4200 is being used purely as an access point. All extras are not in use and are disabled.
Firmware 1.0.03
Hardware version 1.
BASIC ISSUE:The E4200 drops an Apple iPad 2 off the 2.4 Ghz Mixed (B, G, N) network. The user must then select the network to rejoin. Rejoining occurs without incident. The same issue occurs when the network is restricted to B, G. The drops occur at what appears to be random intervals - sometimes 10 minutes apart, sometimes hours apart. We can have as many as 6 drops in an hour. A ping to the apple ipad shows the device stops responding to pings about 10 seconds before the user is prompted to rejoin a network. Meanwhile, a ping to the E4200 itself from a laptop connected via the E4200 on the same radio as the ipad continues to work without fail during this incident.
1. The iPad 2's cannot connect to the 5Ghz radio. I believe iPad 2's are supposed to support 5Ghz.
2. Both our Apple TVs do not connect to the 5Ghz radio: they fail with a "There was an error connecting to the network. Check your settings and try again. (-3914)" error. Apple TV supports 5Ghz.
3. The admin interface for the E4200 is very slow sometimes. Probably over 20 seconds to render some pages when it gets really bad. As a comparison, Internet-based pages on fast sites that delivered via the E4200 itself load in less than 2 seconds.
4. The HTTPS version of the admin interface can only be connected to via Safari browers. Both Internet Explorer 9 and Chrome 16 fail to connect with a "Connection reset" error. In Chome, it says "Error 101 (net::ERR_CONNECTION_RESET): The connection was reset." This is across multiple devices. There is no issue with straight HTTP.
All other devices - including Macs and PCs - connect fine with the E4200 on both 5Ghz and 2.4 Ghz radios, even if they cannot access its admin interface via HTTPS.I've presented quite a few issues above, but the main one is the drop outs for the iPad 2 devices. I'd present logs on drops, but the thing doesn't record any useful logs.
Basic wireless config:
5Ghz:
Network Mode: Wireless-N Only
Channel width: Auto (20 or 40 Mhz)
Channel: Auto (DFS)
SSID Broadcast: Enabled
[URL]
I have configured my e4200 to block traffic at certian times uses both the Parental Controls and the Intenet Access Polices. Neither one seems to work though. [code] I have the same MAC addresses specified in each rule. Initally I had only the first two rules. Those didn't work, so I added rule 3 and 4 (they do the same thing as rules 1 and 2 but from the opposite direction). There are no compliaints, but they don't stop any traffic.
I started with the Parental Controls, they didn't work either. The page in there that lets you pick which machines you want to block seemed next to worthless. I have about four rows listed as "Network Device." REALLY LAME! As the MAC addresses are accesible and these weren't working I went to the IAP.
Router: E4200
Router Firmware: 1.0.03 (Latest FW)
Why I cannot go to the 5Ghz band to utilize the superior speeds to transfer files over wireless connection between my computers? I am sure that I am still on the default 2.4 Ghz because
1) The file transfer speeds are pathetic
2) In Wireless Security, if I set the Wireless Mode to disabled for the 2.4Ghz band, Windows shows me "Unsecured Network" even with 2.4Ghz disabled.
Is the Linksys E4200 Dual Band Router compatible with DHCP and VPN?
View 1 Replies View RelatedThe wireless drops specifically from my laptop constantly at random times. When the wireless drops in order for me to be able to reconnect i have to restart the router itself. There are also random times where the Wi-Fi stops broadcasting altogether. I have a computer connected via Ethernet and it does not lose connection during these times. All the computers are running Windows 7 and the Router is up to date on firmware.
View 5 Replies View RelatedI just upgrade my E4200 V2 from 2.0.37 to 2.1.38 (finally! would be nice if I knew before that I had to unzip the file before I could flash it....)
But when I enable NAT in the settings, there is no way to edit NAT entries that I've set before under firmware 2.0.37.
Just upgrade my Thinkpad to win7 64bit, but seems the wireless doesn't support by E4200 now, upgraded 1.0.03 and latest intel 14.2.0.10 for wlan card but still not working. Tried the TP with USB WN111v2 is not problem at all.4965AG works perfect in office WPA2 AES LEAP and netgear router.
View 9 Replies View RelatedRegion : UnitedStates
Model : TL-WDR3600
Hardware Version : V1
Firmware Version :
ISP : Centurylink
I'm using a WDR3600 router, and I'm having difficulty with getting internet access on the 5 GHz band. Right now the router is broadcasting in both 2.4 and 5 GHz as two separate APs. The 2.4 GHz band works perfectly fine, but when I connect to the 5 GHz band my device is not assigned an IP address and cannot connect to the internet (or even the router configuration page). Unfortunately, I don't have another device capable of accessing the 5 GHz band, so I can't check to see if the computer is at fault, but both the computer and the router have worked together with no problems before, and this computer has done fine in accessing other 5 GHz bands.
I cannot get the Guest Network feature to work.Even though Guest SSID is enabled, it does not show up on any devices attempting to connect. Manually connecting by entering the Guest SSID fails (not recognized). On devices with the primary 5 and 2.4 GHz configured they do see the third network but without SSID (unknown) and are also unable to connect to it manually using the SSID.I did not try this before 1.0.02. Have rebooted modem and verified all configs (multiple times). The network is live in an office and can't keep screwing with it or drastically changing its settings.
View 9 Replies View RelatedI just upgraded to an E4200 from a D-Link DIR-655. I cannot seem to get my desktop to connect to the E4200 at 1 GBS. My adapter is set to "auto negotiate" but will only connect at 100 MBS. If I try forcing the adapter setting to 1 GBS, it never connects. I can swap out my E4200 with the DIR-655 and it will connect at 1 GBS just fine. I am using a CAT 5E cable. Is there something I'm missing here or is the E4200 just more finicky than the the DIR-655?
View 9 Replies View RelatedI just bought the E4200 routher at best buy a few weeks ago. I got it all setup how I want it. Its been working fine then about a day ago it started to stop working at random. All internet just stops working. Wired and Wifi. I have to either wait for it to work again or restart the router.
View 7 Replies View RelatedI have been using the E4200 router with few issues for the past 5 months. I have the latest firmware installed and have 1 pc running Windows 7, a sling box device and USB storage drive connected in the rear and 7 wireless devices.
Over the past week, others in my household have been complaining of not being able to connect wireless. The other day, the connection quit for both wireless and wired connections. I thought it had something to do with my ISP (Comcast), and after I made a direct connect from my modem to my PC, the problem is the E4200. After unsuccessfully troubleshooting, I unplugged the router for a few hours.
Trying a few hours later, I was able to reconnect all connections. However, that lasted for a day and has not been able to connect. I did a reset and when going through the setup process, it says that it cannot connect to the internet. The only time I have any lights or activity on the internet port is when the router is booting up and then it goes off. The rest of the ports are working properly. Likewise, the link light on my modem shows no activity when connected to the E4200. The only connection I can make is to the browser utility.
I am now using another wireless router until I can get this resolved.
The latest Firmware for the E4200 states that there is now the ability to attach a printer to the USB port of the router. I am using a Mac, so that may be the problem, but I have followed the instructions on how to add the printer and it is not happening. It's possible that the MAC Firmware was not given the ability to add a USB printer like the PC Firmware upgrade.
View 9 Replies View RelatedI have an E4200 router & am trying to get it to work with ATV2 through HomeSharing & iTunes. It works fine when my PC is wireless & the ATV2 is wireless. BUT, when the ATV2 is wired via ethernet & the PC is wireless -- nothing!
PC is Win 7 64 - SP1
ATV2 is 4.4.3 (3323) and the router is:
E4200 is 1.0.03 build 14
Just recently bought a Linksys E4200 router and it's been rocking so far! I upgraded from a WRT320N. However it seems that calling with SIP (using my Voip Buster account) doesn't work anymore.I don't seem to be able to register with the Voip service. Port is the standard 5060 (if my memory serves me well, I'm not at home now) and I already activated on the router the special tick for Voip ALG calling. Router is upgraded to the latest firmware and it's the V1 router.With all of the above, I still can't connect using SIP to VoiceBuster. It worked like a charm with the WRT320N so it's something with the router?.
View 2 Replies View RelatedI have the new XBOX 360 black N wireless adapter and the Linksys E3000 dual band router as I want to upgrade the network range and speed to N. I set up a unique SSID and passphrase (WPA2) for both 2.4GHz and 5GHz bands. My XBOX could connect to the 2.4GHz band network and could connect to XBOX Live. But when I configured all the settings and tried to connect to the 5GHz band network, but no luck. My XBOX just said it failed to connect. I was sure that I did type in the SSID and passphrase correctly. I still cannot figure out what went wrong. I even suspected either the wireless adapter or the router malfunctioned.
View 9 Replies View Related
