I am now on my second E4200... But still the same failure.. It looses the internet connection 5-6 times a day, and then I have to switch it off and on to get connection again.
View 9 RepliesI check all of the settings and changed the channel to see if it works. For some reason it disconnects my wireless internet at random times and i know before it never use to do that before with a older router. There is nothing blocking it, it worked before, and my computers can connect except two. The only thing i can guess is my wireless card.
View 6 Replies View RelatedI started using E4200 few months ago. It used to have frequent disconnection with E4200 when it's running on router mode back then. After playing with the MTU from 1492 (recommended by ISP) to 1364, it's seems to be quite ok until recently.It is getting worst than before. It disconnect my internet almost few times in 5 minutes.
[CODE]...
I have configured my e4200 to block traffic at certian times uses both the Parental Controls and the Intenet Access Polices. Neither one seems to work though. [code] I have the same MAC addresses specified in each rule. Initally I had only the first two rules. Those didn't work, so I added rule 3 and 4 (they do the same thing as rules 1 and 2 but from the opposite direction). There are no compliaints, but they don't stop any traffic.
I started with the Parental Controls, they didn't work either. The page in there that lets you pick which machines you want to block seemed next to worthless. I have about four rows listed as "Network Device." REALLY LAME! As the MAC addresses are accesible and these weren't working I went to the IAP.
I have an e4200 with the latest firmware 2.1.39. I just upgraded the firmware due to connection issues with my DSL. I now have the same issues with disconnects but I believe they are being caused by a different issue. When I try and log into my router through the IP address it wont let me, it says it can't find the router. Eventually after getting in the first time by using the default password, I have twice found out that all my settings are gone. This has happened twice this week and only happened after upgrading the firmware but I can not tell if firmware is causing it or if it is hardware related. I now reboot and restore saved firmware but that is a hassle and am pretty sure that is not the way it was designed to work.
View 9 Replies View Relatedi have a WUSBF54G that will connect to my router just fine. Right when the device is first plugged in there aren't any problems. I can ping my router, I can ping google.com. The browsers all work correctly, etc. But after a while, maybe 30 minutes (it varies) I lose the connection to the internet. I can still ping the router. I can ping other devices on my network. But I cannot ping any websites by DNS name or by IP address and any browser I use won't display any websites. I have other wired and wireless connections on this network that don't have any problems. I even unplugged this adapter and plugged it into a different computer and had similar results. The device is relatively new (maybe a month old, but only used a few times within that month, and the use that it did get is mostly from trying to troubleshoot this issue.) Both computers I have installed the device on are running Windows 7 Ultimate. Both computers have the latest drivers installed from this site:
[URL]
I have a netopia 3000 router and I have checked to see if the problem could be caused by this router but there is nothing out of the ordinary there. All of my troubleshooting has been using the Win 7 "network and sharing center" to connect. I couldn't get the linksys connection tool to work and actually, I noticed after reading this forum that the linksys wifi connection tool doesn't work with win 7 after all so I don't think using the built in win 7 wifi tools would cause the issue. Also, just to clarify, in an attempt to resolve the issue I have tried dynamically assigning an IP address for this connection and also a static IP address. Either method seemed to yield no results. It is a frustrating problem to say the least. I don't want to believe that the adaptor is faulty. As I said it is relatively new. Also, as I mentioned, when I first plug it in it will work correctly for about the first half hour or so before it will stop reaching the internet. I then have to physically unplug the device and plug it back in in order to correct the issue. I was thinking of creating some kind of script that will automatically disable the adapter every 30 minutes and then enable the adapter. I ran into another issue here though. If I disable the adaptor (either from device manager or from "Network Connections) the device will change status from "Not Connected" to "Disabled." So far so good. But then, when I go to enable the adaptor again the adaptor disappears from the list. It's as if it isn't plugged in any more. The only way to get it back is to physically unplug the device and physically plug it back in. How to "Enable" the device without it disappearing from the network adapter list.
I have a wireless router which is connect to a DSL modem. Everything was working fine but now the wireless router looses connection often and if i remove the RJ45 check from my wireless router and plug it in after few minutes it works but again it looses connection.
View 2 Replies View Relatedmy E4200 is dropping connections several times a day. I'd be working on my laptop, go to a webpage and bang, no connection. A minute or so later it would reconnect. It even appears to be doing this with a computer that is hardwired to one of the ports. So it doesn't seem limited to just wireless. Happens to both N and g channels as well.
View 9 Replies View RelatedUpdated firmware was installed and settings were reviewed. Intermittently the E1500 looses its ability to connect only to our Android devices and "Cisco Connect" displays that it has lost Internet connectivity. The PC hard-wired to the E1500 and another PC connected wirelessly both work fine when this happens, despite the Cisco Connect message. The Android devices show the presence of the network, but they never "connect" - find the IP address. The problem can only be resolved by re-booting (powering off/on) the E1500. The loss of connectivity to our two Android devices and the Cisco Connect error display always are concurrent. E1500 looses connection to Android devices
View 9 Replies View RelatedHad an E4200 for a couple of months now and have not been able to resolve an issue with the router dropping an Apple iPad 2 at random times.The E4200 is replacing a Cisco Aironet 1200, which never dropped any clients, iPad 2 or others, and never displayed any of the issues below.
TECH DETAILS:The E4200 is being used purely as an access point. All extras are not in use and are disabled.
Firmware 1.0.03
Hardware version 1.
BASIC ISSUE:The E4200 drops an Apple iPad 2 off the 2.4 Ghz Mixed (B, G, N) network. The user must then select the network to rejoin. Rejoining occurs without incident. The same issue occurs when the network is restricted to B, G. The drops occur at what appears to be random intervals - sometimes 10 minutes apart, sometimes hours apart. We can have as many as 6 drops in an hour. A ping to the apple ipad shows the device stops responding to pings about 10 seconds before the user is prompted to rejoin a network. Meanwhile, a ping to the E4200 itself from a laptop connected via the E4200 on the same radio as the ipad continues to work without fail during this incident.
1. The iPad 2's cannot connect to the 5Ghz radio. I believe iPad 2's are supposed to support 5Ghz.
2. Both our Apple TVs do not connect to the 5Ghz radio: they fail with a "There was an error connecting to the network. Check your settings and try again. (-3914)" error. Apple TV supports 5Ghz.
3. The admin interface for the E4200 is very slow sometimes. Probably over 20 seconds to render some pages when it gets really bad. As a comparison, Internet-based pages on fast sites that delivered via the E4200 itself load in less than 2 seconds.
4. The HTTPS version of the admin interface can only be connected to via Safari browers. Both Internet Explorer 9 and Chrome 16 fail to connect with a "Connection reset" error. In Chome, it says "Error 101 (net::ERR_CONNECTION_RESET): The connection was reset." This is across multiple devices. There is no issue with straight HTTP.
All other devices - including Macs and PCs - connect fine with the E4200 on both 5Ghz and 2.4 Ghz radios, even if they cannot access its admin interface via HTTPS.I've presented quite a few issues above, but the main one is the drop outs for the iPad 2 devices. I'd present logs on drops, but the thing doesn't record any useful logs.
Basic wireless config:
5Ghz:
Network Mode: Wireless-N Only
Channel width: Auto (20 or 40 Mhz)
Channel: Auto (DFS)
SSID Broadcast: Enabled
[URL]
I have a E4200 updated to the latest firmware I have problems with the wifi on the 2.4GHz band, in fact, at power on, many times wi-fi on the 2.4GHz band doesn't work but the 5GHz band works normally. After some reboots the wi-fi operating normally on both bands.
View 9 Replies View RelatedI have an EA4500 router. It's the latest in a long line of Linksys routers I've owned and I'm pretty familiar with setting one up and making changes. But the EA4500 seems a bit more picky than previous routers. Last night I tried to enable port forwarding for ports 53, 80, and 88 for my xbox. I already had port 3074 forwarded. When I did that and applied the change, I lost all Internet connectivity. I tried cycling the power on the router with no luck. I finally got connected again by going to 192.168.1.1 and disabled those ports. The status page then said I had Internet connectivity but I really didn't at least right away. It took a couple minutes before I was actually able to to connect to the Internet again. What else should I check when it says I don't have internet connectivity?
View 3 Replies View RelatedI upgraded my Linksys from 160n router to 4200V2 router. I configured 3 wireless Linksys webcams and they work fine. After 24hrs they i cannnot connect the via HTTP and webcames IP addresses disapear from the DHCP client table. If reboot the webcames the it works fine for next 24hrs. I did not make any modification to any settings and the setting looks just like i had on the 160N router
View 1 Replies View RelatedI have my e4200 connected to another modem/router (2Wire 3600HGV), because the other router does not support Wireless N. I can connect to my E4200 network, but there's just no connection to the internet. I reseted my e4200 but still no luck. I've unplugged both routers and replugged them, nothing. I know it's possible because I've had it set up before but I had my 2Wire exchanged for a newer one.
Firmware: 1.00.4
Just to be sure. I have the cable going from my modem out of port #1 and into my e4200 where it says internet, thats correct, right? On my e4200 i have the IP 192.168.1.2 but on the 2Wire I have the e4200 as 1.92.168.1.66.
I have a E4200 V1 with firmware 1.0.0.5 installed The problem is that when I connect the cable from my modem to my router and recycle both I get a rapidly fashing Cisco light and can not connect to the internet.If I remove that cable and recycle the router my network works but (obviously) I have no internet connectivity.This was working (almost 2 years) without issue until today.I updated the firmware and did a factory reset and neither resolved the issue.My next experiment is to see if I can't get log files (since the factory reset) but I can't do that at this time.
View 3 Replies View RelatedI just purchased e4200 from a friend of mine. Got an issue with setup of this device. I use a model from internet provider. Have 2 computers at home. One is pc with cable, another one mac with wireless.SO my issue is that i can not connect none of them. I was trying to use cd that comes with router but he can not locate a router. When I connect cable directly from modem to computer everything works fine. As soon I connect cable to a router I can not see a router and I can not connect to internet.
View 1 Replies View Relatedever since i had a power failure losing all power in my apartment, my router has begun regularily losing connection to the internet, I have to go into the router and renew ip address which is quite annoying
[code]....
I setup my E4200 v2 with different SSID's for 2.4 and 5GHz modes. I have no problem with a 2.4 Ghz connection on my laptop, but I cannot connect to the internet in 5GHz. mode. I choose the 5 GHz SSID and enter the passphrase but no luck, even though I have a full 4 bars inthe wireless icon.
View 4 Replies View Relatedmy e4200 wireless. I have internet connection speed of 40mb and I have epc 3925 working in bridged mode as modem and E4200 as router. When I connect my laptop with wire on e4200 I am getting 37-38 Mbps on speedtest.net which is perfectly fine. But on wireless I am having a lot of dropping of speed: I have 2mps then jumping to 5-6 Mbps and so on it never goes more than 5-6 Mbps. When I disable WMM Support in QoS I am having perfectly constant 20mbps but... I have only g network 54mbps. [code]
View 9 Replies View RelatedI have a brand new E4200 with two desktop computers using it with no problems. I also have a work Thinkpad laptop that I use a couple of times a week from home. Since day one of installing the new router, I have experienced the blue screen of death numerous times during the day (the number of times varies from 1 to 6 on a really bad day). I believe this is happening when I lose my connection to the router. I can see it trying to reestablish itself but the VPN will drop the connrection before it has a chance. I never lost my VPN connection until the day I installed the new router. Yesterday, at least one time it was unable to reestablish connectivity with the router and I had to reboot the laptop to get it connected. Could this have something to do with the IP address? I do not have any issues with the laptop when I am at work using a docking station.
So, I am wondering why I am constantly losing connectivity on the laptop only. The laptop has Windows XP and I am using AT&T Global Network Client to access the work network. Is there a setting somewhere that will fix this? Our IT folks rebuilt my laptop and I am still experiencing the same problem. I checked and I have the current version of the firmware for the router.
I'm using a refurbished E4200 that's connected to a SpeedStream 5360 modem to establish an Internet Connection over PPoE (ATT DSL). Connected to Ethernet ports I also have a NAS and an Airtport Express (with wireless off - it's only there for AirTunes/AirPlay).I'm getting Internet drop offs and then completely lose the WiFi, about every other day.E4200 drops Interaction Connection (PPoE)
View 4 Replies View RelatedI have a brand new E4200 constantly losing internet connection (both wireless and wired). I have a ADSL connection to the internet, last router I had did not have the same issue. I also have a Cisco ASA 5505 for work connected to the ADSL modem and is not experiencing any disconnect issues. All computers connected to the router is losing internet connection, local lan keeps working. The internet connection gets back again after a 10-15 minutes or when resetting / turning off the router.
I have tried the following;
Changed ethernet cables
Disconnected the ASA 5505
Turned off wireless
Upgraded the firmware
Reseted to factory settings
I have a home network with a Linksys E4200 connected to the ISP's fiber box. The problem is that when I'm connected to the Linksys, either wired or wireless, the connection to the internet will drop after what seems to be a random amount of time (normally anywhere from 2-10 minutes). I can restore the connection by doing any of these things:-reboot Linksys-disconnect and reconnect cable from router to fiber box-if on wireless connection, make changes to the router wifi settings, like change the wifi channel.The internal network stays up, and I can ping both the internal and external ip of the router, but not the fiber box. I have also had the same behavior with an Edimax Wifi AP and less frequently with a Edimax router (once every 1-2 days). I have done everything I can think of:-changed the wifi channels-changed the ip ranges, subnets, turned router DHCP off and back on-booted the fiber box-changed cables-updated all routers to the latest firmware, the network cards with latest drivers...and loads other things that I don't remember right now. For the wifi side of things, there are no other networks in range that could interfere. The same problem occurs on both my and wife's Win 7 laptops and on the iMac (latest OSX). Here's a fun detail: while the Linksys has lost its connection to the internet, I can still access the internet through the old Edimax router connected to the same fiber box, either wired or wireless.
View 1 Replies View RelatedI've recently picked up a E4200 to build a dual band network which is targeting to link up (TV, media server, ps3, laptops) then (maintaining phones etc which only has b/g). While currently only laptops.Before doing any of these I have another cisco modem router DPC3825 which worked fine with giving wireless access.I first attemped to leave the modem router has is and connected the E4200 (ethernet 1 to internet), and changed ip to x.x.0.1 and x.x.0.2 while disabling wireless on the dpc3825 and the DCHP on the e4200 and have default gateway to x.x.0.1. My laptops can connect to wireless on E4200 but it couldn't get internet access.
Then I tried turning the modem to bridge mode & resetted E4200 (factory setting x.x.1.1, auto DHCP), and then connected my devices to both wireless bands. At this point I see router status obtained ip from ISP and Internet reached full speed per ISP's mark but the connection only held up for about 1 minutes. I noticed all the devices still maintained connection to router wirelessly but the router loses internet connection (lost the ip and couldn't get it back).
I have a WRT120N router .It has something to do with turning on or re-introducing certain wireless devices into the area. When I come home with my iPhone & my wife is on her computer, suddenly the wifi stops. And vice-versa. It's ridiculous. I'm not a computer programmer but if I was I'm pretty sure this would be a no-brainer to fix. Especially if the company that paid me took pride in their products.
View 8 Replies View Relatedmy router drops connection several times a day. I have to unplug the router every day so that my devices can stay connected. I hate when this happens late at night when i'am upstairs and have to go 2 stairs down to get internet on my devices. For example if i want to connect my iPhone to my Wireless network it gives me an error with: 'No connection can be astablished with this network'.
View 1 Replies View RelatedI saw one post recommending to changing the MTU from 1500 to 1400. That did absolutely nothing. My comcast internet is now slower than 14.4 dial up modem I had 16 years ago. The strange thing is I can sometimes download at over 2 mbps with torrents. It's mainly loading websites where the speed is so bad.
View 9 Replies View RelatedRegion : UnitedStates
Model : TL-WR1043ND
Hardware Version : V1
Firmware Version : 3.13.12 Build 120405 Rel.33996n
ISP : AT&T
Every 5 to 7 days my router loses connection with WAN (ISP modem) but connection over LAN is fine. It seems that 1043ND tries to connect to DSL modem from AT&T by username and password (that does not exists) instead of doing Dynamic IP. I understand that AT&T modem is of type of PPPoE but there is not a password or user id and connection must be dynamic. Page 192.168.0.1/logininfo of modem complains that I was trying to login with incorrect user id password. Every time I have to
1- connect the modem directly to my computer so the modem resets.
2- I have to reset 1043ND to factory default, reboot, and connect cables back how they were, Then go to WAN page do a release and renew to get connected to WAN again.
I have a problem with my laptop...i have a Packard Bell laptop connected to my wireless router WAG 320n and it has been working fine until yesterday when it didnt connect automaticly as it have been doing before because i have my ssid network saved on my laptop!
I logged on to the router page and changed from standard channel to wide channel and also tried different channels at the same time that i tried connecting with the laptop but i get the same message everytime "Unable to connect!
My dad recently got a E4200 router, My whole family are mac users, the connection are all okay with their computers, I'm the only one using Microsoft, ASUS running on Vista. The connection is fine when I'm near the router, but when I go to my room I get no connection at all, it connects for a second but then it goes on connection with limited access.
View 5 Replies View RelatedLast week I bought the E4200 thinking it was probably the best router on the market and if it worked properly, it would be...I think.I have attached a Seagate GoFlex Desk 2Tb USB drive formatted to NTFS to the USB of the E4200. I can map to it from my Windows XP computer with no problem and I can FTP to it from any browser...my Windows 7 machine is another story. When I try to map the network drive from the Windows 7 machine I get error code 0x80070035 every time. I've seen some other threads where people are having this problem but in the cases I've found, they aren't getting any connection via XP or FTP either.
View 2 Replies View RelatedI have just installed Cisco Connect v1.4 (11266.0), and have upgraded my E4200 software to 1.0.03.I want to add a USB printer connected to the router but when I open Cisco Connect, and select the "Add new devices.....' button, the only option for a printer is 'Wireless Printer' not 'Printer' followed by USB or Wireless as per the User guide.
View 9 Replies View RelatedI have an E4200 (v1) with the latest firmware. For some reason, the E4200 does not allow me to conenct to certain websites. This is true for wired or wireless connections.To test, I connected a wired PC directly to my cable modem and was able to connect to all websites fine. I also tried an old D-Link router I had on hand and was able to connect to all sites fine. Went back to the E4200 and was blocked. I re-loaded the firmware and same results.
View 4 Replies View Related