I upgraded my Linksys from 160n router to 4200V2 router. I configured 3 wireless Linksys webcams and they work fine. After 24hrs they i cannnot connect the via HTTP and webcames IP addresses disapear from the DHCP client table. If reboot the webcames the it works fine for next 24hrs. I did not make any modification to any settings and the setting looks just like i had on the 160N router
View 1 Replies
I've got a Linksys 4200v2 with a laptop client that has an Intel 5300 with 3 antenna. I am trying to get to the 300 or 450mbps speeds, but can't seem to do it. I seem to be able to get 217Mbps on both the 2.4 and 5 GHz bands. Does this seem to be a NON-bonded speed? How do I enable bonded speeds? Here is what is wierd, when I enable 40MHz Channel width on teh 5GHz band, the laptop cannot connect. If I drop it down to 20MHz, it will connect. What are the settings I need to reach 300 or 450mbps speeds? Does the 2.4 and 5GHz band need to be set with the same settings? I mean, do they use each others bandwidth to achieve 300 or 450Mbps?
View 5 Replies View RelatedI am now on my second E4200... But still the same failure.. It looses the internet connection 5-6 times a day, and then I have to switch it off and on to get connection again.
View 9 Replies View RelatedUpdated firmware was installed and settings were reviewed. Intermittently the E1500 looses its ability to connect only to our Android devices and "Cisco Connect" displays that it has lost Internet connectivity. The PC hard-wired to the E1500 and another PC connected wirelessly both work fine when this happens, despite the Cisco Connect message. The Android devices show the presence of the network, but they never "connect" - find the IP address. The problem can only be resolved by re-booting (powering off/on) the E1500. The loss of connectivity to our two Android devices and the Cisco Connect error display always are concurrent. E1500 looses connection to Android devices
View 9 Replies View Relatedi have a WUSBF54G that will connect to my router just fine. Right when the device is first plugged in there aren't any problems. I can ping my router, I can ping google.com. The browsers all work correctly, etc. But after a while, maybe 30 minutes (it varies) I lose the connection to the internet. I can still ping the router. I can ping other devices on my network. But I cannot ping any websites by DNS name or by IP address and any browser I use won't display any websites. I have other wired and wireless connections on this network that don't have any problems. I even unplugged this adapter and plugged it into a different computer and had similar results. The device is relatively new (maybe a month old, but only used a few times within that month, and the use that it did get is mostly from trying to troubleshoot this issue.) Both computers I have installed the device on are running Windows 7 Ultimate. Both computers have the latest drivers installed from this site:
[URL]
I have a netopia 3000 router and I have checked to see if the problem could be caused by this router but there is nothing out of the ordinary there. All of my troubleshooting has been using the Win 7 "network and sharing center" to connect. I couldn't get the linksys connection tool to work and actually, I noticed after reading this forum that the linksys wifi connection tool doesn't work with win 7 after all so I don't think using the built in win 7 wifi tools would cause the issue. Also, just to clarify, in an attempt to resolve the issue I have tried dynamically assigning an IP address for this connection and also a static IP address. Either method seemed to yield no results. It is a frustrating problem to say the least. I don't want to believe that the adaptor is faulty. As I said it is relatively new. Also, as I mentioned, when I first plug it in it will work correctly for about the first half hour or so before it will stop reaching the internet. I then have to physically unplug the device and plug it back in in order to correct the issue. I was thinking of creating some kind of script that will automatically disable the adapter every 30 minutes and then enable the adapter. I ran into another issue here though. If I disable the adaptor (either from device manager or from "Network Connections) the device will change status from "Not Connected" to "Disabled." So far so good. But then, when I go to enable the adaptor again the adaptor disappears from the list. It's as if it isn't plugged in any more. The only way to get it back is to physically unplug the device and physically plug it back in. How to "Enable" the device without it disappearing from the network adapter list.
I have a wireless router which is connect to a DSL modem. Everything was working fine but now the wireless router looses connection often and if i remove the RJ45 check from my wireless router and plug it in after few minutes it works but again it looses connection.
View 2 Replies View RelatedRegion : UnitedStates
Model : TL-WR1043ND
Hardware Version : V1
Firmware Version : 3.13.12 Build 120405 Rel.33996n
ISP : AT&T
Every 5 to 7 days my router loses connection with WAN (ISP modem) but connection over LAN is fine. It seems that 1043ND tries to connect to DSL modem from AT&T by username and password (that does not exists) instead of doing Dynamic IP. I understand that AT&T modem is of type of PPPoE but there is not a password or user id and connection must be dynamic. Page 192.168.0.1/logininfo of modem complains that I was trying to login with incorrect user id password. Every time I have to
1- connect the modem directly to my computer so the modem resets.
2- I have to reset 1043ND to factory default, reboot, and connect cables back how they were, Then go to WAN page do a release and renew to get connected to WAN again.
I have an e4200 with the latest firmware 2.1.39. I just upgraded the firmware due to connection issues with my DSL. I now have the same issues with disconnects but I believe they are being caused by a different issue. When I try and log into my router through the IP address it wont let me, it says it can't find the router. Eventually after getting in the first time by using the default password, I have twice found out that all my settings are gone. This has happened twice this week and only happened after upgrading the firmware but I can not tell if firmware is causing it or if it is hardware related. I now reboot and restore saved firmware but that is a hassle and am pretty sure that is not the way it was designed to work.
View 9 Replies View RelatedI have a problem with my laptop...i have a Packard Bell laptop connected to my wireless router WAG 320n and it has been working fine until yesterday when it didnt connect automaticly as it have been doing before because i have my ssid network saved on my laptop!
I logged on to the router page and changed from standard channel to wide channel and also tried different channels at the same time that i tried connecting with the laptop but i get the same message everytime "Unable to connect!
I have an EA4500 router. It's the latest in a long line of Linksys routers I've owned and I'm pretty familiar with setting one up and making changes. But the EA4500 seems a bit more picky than previous routers. Last night I tried to enable port forwarding for ports 53, 80, and 88 for my xbox. I already had port 3074 forwarded. When I did that and applied the change, I lost all Internet connectivity. I tried cycling the power on the router with no luck. I finally got connected again by going to 192.168.1.1 and disabled those ports. The status page then said I had Internet connectivity but I really didn't at least right away. It took a couple minutes before I was actually able to to connect to the Internet again. What else should I check when it says I don't have internet connectivity?
View 3 Replies View RelatedI dont know why this keeps happening, It was a problem last summer and now its happening again. My modem looses connection and only a few lights are on. Im using comcast in the DC/Metro area and Im using a telephone modem.
View 12 Replies View RelatedI have a server (Windows Server 2003) that randomly looses connection with the default gateway and anything on the outside. When this happens, the server cant ping the gateway (A Juniper SSG5 firewall/router) and the gateway cant ping the server. But the server still can ping anything else on the network and everything inside the network works fine with it. The most reliable remedy is to reboot the router. Rebooting the server or resetting the network card sometimes works. I have tried both onboard network cards and a separate PCI network card on the server. There are no router log entries that correspond to the problem. This server is used as a Terminal Server for a remote office and as a file server.
View 1 Replies View Relatedwrt54gs connects but after about a minute it looses connection and boots continuously
View 1 Replies View RelatedMy new RVS4000 (2.0.2.7) connects the WAN via PPoE with dynamic IP which is held at DynDNS and normally I see the RVS4000 via a router-to-router-VPN. That works fine so far, but every "some" days the router looses WAN connection (and with ist VPN). When this happens, last DynDNS-update is hours ago, so it didn`t reconnect. Looking on the routers site, the LAN is fully functional for clients that have got their DHCP-Information. New clients don`t get DHCP-Info (IP-address, DNS), both do not have internet access. The router`s WAN-summary shows, that it thinks to be "CONNECTED" but with empty WAN-IP and DNS entries. Klicking "DISCONNECT" and then "CONNECT" again solves the problem so far. The loss of connection is not the periodic break from the IPC, which is correctly identified and reconnected as configured. I wanted to trace the problem with the log, but there is also a bug. It stops logging at some time completely - neither email-log nor local log, so I never happend to be lucky to hit the point of loss of connection. Also the local log provides a first and next pages, but the next pages are always empty - not really useful.
View 3 Replies View RelatedI recently started having trouble with my VPN clients loosing connection.I can create the conenction, work with it for a while, and then loose connectivity.Timing seems to be dependent on the activity over the connection.More activity, the conenction stops working sooner.
The cleint doesn't disconnect, I just can't access anything from the client.Disconnecting and reconnecting the client fixes the problem, temporarily depending on how much data I'm transferring.This works 90% of the time.The other 10% if I wait 30-45 minutes, and try again.. It works...with the same results...
It was originally isolated to a Win 2003 server that I was using as the client.It is now happening on my Win XP client as well.I'm using the AnyConnect client ver. 2.5.2014 with the VPN service on the UC520.Which I beleive, is similar to the ASA 5500 series VPN device.I am running ver 8.1.0 on the UC 520, and I can't remember if this started after upgrading to the new software.
Newly purchased DSC-930L connected to DIR-625. Firmware is 1.0 for DCS-930L and A1-1.09 for DIR-625.Camera works fine when connected with cable. Wireless enabled, fixed IP address.Unplug cable and camera still works fine for a while: can access the view page and view picture that does change. F5 refreshes page no problems. After a while (about 5 minutes) web page no longer reachable by browser. Reconnect cable and works fine, unplug and repeat the cycle same thing happens.Also tried: unplug ethernet cable, unplug power cable, wait 10 seconds, connect power cable, try to browse to camera - cannot reach camera.
View 13 Replies View RelatedI have a DIR-655 Rev B1, FW 2.01 (I will probably upgrade the FW tonight to the latest.)
I have at least 20 items that connect wirelessly to this router (2 PCs, 2 Laptops, 2 Tivo Box, 3 Game Consoles, 3 Cell Phones, 2 Tablets, 2 TVs, Printer, AP Gateway, and some other projects) It's been a solid connection to everything for the past couple of years.
I bought a new Dell Inspiron 15r SE laptop (uses the Intel Centrion Wireless-N 2230 Wifi Solution.) After anywhere from 2 - 10 mins of browsing/watching a video/downloading files the access out to the internet simply stops.
At this point I'm still connected wirelessly to the router, and if I go to the router address I still have access and can login and see the router settings. I check and there's plenty of time left on the lease (days.) Still not getting internet access. Eventually my Laptop will disconnect and reconnect (or I do it manually.) I've performed hard resets of the router, I've had my laptop Forget the network and then reconnect, etc. Nothing has resolved it.
I thought it may be my laptop, but I've taken it to Starbuck, Work, Neighbors WiFi, etc and I don't have any problems staying connected on their networks.
I've had Dell on the line, we connected hardwired, and there solution was to force forget and reconnect to the router, which worked for the 10min he was on the line with me, but then failed soon after, and back in the same connectivity hell
We have some 1242 LAPs in a two 5508 controller setup working fine. All LAP are configured to obtain address from DHCP. After first join we usually change some configs like HOSTNAME, AP GROUP, PRIMARY AND SECONDARY WLC. After a software restart or a complete power off/power on the LAPs joins the primary controller and all configuration still there. We now add a 1142 LAP and is does not retain the configuration after a power off/power on cycle, but after a software restart there is no problem. The only way to retain the config is setting the AP with a static IP address.
We use WLC 7.0.116 and we see no errors in the LAP console.
I have copied my computer's time in the router time setup under Time in the "tools" section of the router setup. After a few days of the router being up without a hard restart, it has lost 10 minutes somehow. I went to the logs and cleared them out and then looked at the entry showing that the log was cleared and looked at my computer clock and the time stamp of the log entry, and it was 10 minutes slower than my computer clock that I had originally set it from. I have a clock plugged in by the computer, and my computer always matches the clock that it plugged in, so I know it isn't my computer loosing time. What is going on here? Why does the router loose the correct time after it has been up and not unplugged or rebooted at all? I know that the router will loose the time if you unplug it, but this isn't the case here.
View 5 Replies View RelatedI have a WES610N in my office connected to a E4200 @ the cable modem in the family room. ~30'.The connection is fine and works well when working.Connected to the WES610N I have:
-Polycom VOIP phone
-HP Mediasmart Windows Home Server
-Desktop
-Multi-Function Laser Printer
I have two issues.
1) The Polycom does a random reboot that I have traced down to it loosing it's IP
2) The Windows Home Server looses it's IP requireing a hard reset.
I have enabled QOS for the polycom and that just worked with managing data. However both devices seem to loose their IP regularly. The desktop might also be having the issue but because it is Vista I suspect Vista is better equipped to deal with IP issues.
I just connected a WRT190N v2 Wireless Router to my XPS 400. When my wife tried to connect our other desktop to the wireless network, everything seemed fine. I noticed that, when she wasn't actively browsing or using the network, her computer would lose connectivity, but regain it when a browser was opened. When I tried to use the XPS, I found that it had no connection. I regained connectivity after using the Windows Network Diagnostic tool, but neither computer seems to keep connectivity when left alone, at least for very long.
View 1 Replies View RelatedI get frequest Airport Express wireless connection drop and reconnect with my replacement e4200v2 running the latest firmware. I have it connected the 5Ghz band and set to channel 161.
View 9 Replies View RelatedFor the last 4 years I’ve been using the Linksys Router, model WRT150N V. 1.1 and never had any problems—until now.Yesterday I noticed that my wireless devices (i.e., two computers, tablet and Internet radio) either don’t work at all (the Internet radio) or the pages load extremely slowly—for example, the tablet has become, for all intents and purposes, unusable. Since my ‘main’ computer is connected directly to my cable internet, I know that there is nothing wrong with the Internet connection itself, only with wireless connection.I disconnected the Linksys Router for 2 minutes and reconnected it, but to no avail. I know that I have not made any changes to any software/hardware that might affect the speed.Since I also happen to have access to another wireless Internet connection (a different provider), I connected to that network and all my wireless devices were working perfectly. Therefore, I think the problem must be with the router. I am using Windows XP (on the main computer, where the router and Internet cable are attached).
View 5 Replies View RelatedI currently have a Linksys E1200 router and I am getting anywhere from .3-.5 of a megabit per second download speed while upload speed ranges from 2-5 Mbps. This is very strange to me as I have never seen a connection this slow or one that had a higher upload speed than download speed.
View 7 Replies View RelatedMy WRT160N V3 halves my connection speed (5mbps to 2.7)with both wired and wireless. I have tried changing a lot of settings.
View 4 Replies View RelatedI have a WRT160N with one desktop connected via a lans cable, another desktop connected wireless via WUSB300N and a Laptop connected wireless via WPC600N.
View 6 Replies View RelatedIf I get a new wireless router that is N and attach it to my desktop computer, will my laptop which has a G wireless card in it be able to work without any modification? I thought I read that N is downward compatible with B and G cards, but then I saw some kind of network adapter that is put in the USB and wondered if I'd have to do that with the laptop. I'm leaning towards a E3200 right now.
View 2 Replies View RelatedI haven't changed anything apart from the SSID names so I can choose which device has access to which band 2.4 or 5ghz.I've come across an issue with the wireless and it drops connection randomly. I have to then disable and enable wireless adaptor on my laptop to connect again.I have read reports of allot of people having this issue however the majority of the issues were over a year ago (2011). Am I to assume this issue was resolved with a firmware upgrade somewhere which I may of missed? My current firmware is 2.1.38.138880. Is this the most up to date?
View 5 Replies View RelatedWRT54G2 router has been working great since I got it a year ago. But recently I'm experiencing really slow wireless speed. My normal speed is around 15 Mbps but now it has dropped to about 0.85 - 1.0 Mbps. At first I thought someone might be using my connection without my knowledge so I changed the password but it was still slow. I then changed my wireless channel (I heard that if too many people are on the same channel it can cause interference) and it worked. However, a little bit later (sometimes a few hours and sometimes a few days) my connection would become slow again. I have also tried upgrading my firmware but no luck.
View 3 Replies View RelatedI have a Linksys WRT54gX2. When I make a wired connection from my modem to my computer (Vista - latest SP) I get a connection to the internet on my computer. When I run a network cord from the modem to the wireless router and then a network cord to the computer, two things happen:I do not get a connection to the internet on my computer.With laptops and iPods that are trying to connect wirelessly, I can see that the wireless signal exists, and the devices can connect to the signal, but no internet connection passes through. There are no firmware updates that I can find for this device, I have powered the router on/off for 30 seconds, and I have used the reset button.
View 1 Replies View RelatedI'm running Windows 7 64bit and I have sucessfully configured my wireless print server (Linksys WPSM54G) to work with my computer and our HP DesignJet 500ps. I have been able to print several sets of drawings without issue, however if the plotter is inactive for an extended period of time (1 hour +/-) the wireless print server loses connection with our router. At the same time the print server loses connection, an associate in our office with a wireless connection to his computer also loses connection to the router. A simple power cycle of the router and print server restores the wireless connection
I chatted with Linksys online tech support and they confirmed that I had the most recent firmware in both the router and print server and had me reconfigure some of the wireless settings on the router. All was good until about an hour ago when I tried to plot and discovered that the print server had lost it's connection to the router and my associate had also lost his wireless connection.
What's the deal here? I feel as though the root cause of this issue is related to the wireless router rather than the print server as my associate was periodically losing connectivity to the wireless router before installing the print server.
I have a E4200v2 and im getting wireless connection issues. I have updated to the lastest firmware and have checked all my wireless settings. I dont use usb storeage. I have 1 laptop using 5G, my iphone using 2G and my wife mac using also 2G.. the problem is that, once we stop using the 2G connection (leave it overnight), it just dies the next day.. it wont connect, i double check the password and it wont connect. But the 5G connection is fine.. Do i have a break E4200v2? or anyway of fixing this?
View 2 Replies View Relatedip - Comcast.....
tower card - Creatix CTX404 WLAN 802.11b.....
Router - Netgear WNR1000v2 (supplied by Comcast)
Modem - RCA - DCM 325 (Also supplied by Comcast)
Window XP Pro w/SP3
Security - WPA-PSK
I'm getting in no special order
a "validating identity" or "authorization failed" or "unable to find a certificate to log you onto the network" or "limited or no connectivity...etc..."
I have removed the check in front of the enable box in the Authorization Tab. The only difference I have noticed is that the icon in the task bar instead of a white on red X I now get a Black on yellow triangle...but still no connection...all this after a couple of days worth of **bleep**
