Linksys Cable / DSL :: Laptop Looses Contact With Wireless Router WAG 320n?
May 7, 2011
I have a problem with my laptop...i have a Packard Bell laptop connected to my wireless router WAG 320n and it has been working fine until yesterday when it didnt connect automaticly as it have been doing before because i have my ssid network saved on my laptop!
I logged on to the router page and changed from standard channel to wide channel and also tried different channels at the same time that i tried connecting with the laptop but i get the same message everytime "Unable to connect!
View 2 Replies
ADVERTISEMENT
Nov 6, 2012
I have my broadband line feeding into a WAG 320N in an outside room. There are computers in the outside room which are wired to the modem via CAT leads & plugs. Wireless is turned on, but is not currently being used in this room, as the wired connections work fine. From this outside room there is an underground cable (12 metres) to the house, which through a CAT lead is plugged into another WAG 320N, which operates primarily wirelessly, so laptop computers can be used in the house wirelessly. When the outside room modem is turned on AND the house modem is turned on, only one modem OR the other can access the internet, NOT BOTH. Why can't both modems operate wired and wirelessly. What is the problem? Is there a conflict between the two wireless signals? Can/ should I turn off the wireless signal from the outside modem (if so HOW?) . OR is there a way I can have both modems transmitting a wireless signal.
View 1 Replies
View Related
Feb 25, 2012
After a very unsuccessful attempt to talk with technical support, I decided to post here. I probably should have posted here first... lesson learned.I have Comcast Cable internet and get approx 24-25 Mb/s download speed when directly connected to the modem.When I connect via the router's ethernet port, my download speed drops to 14Mb/s.When I connect via wifi -- the download speed drops the whole way to 1.5Mb/s?
View 4 Replies
View Related
Dec 30, 2011
I have a home network of 2 desktop PCs. One runs Windows 7 64bit, the other WinXP with SP3. Both have all current updates applied.Both are wirelessly connected via a Cisco-Linksys WAG160N wireless router with Firmware Version:V1.00.16.When the two machines are in contact, file and printer sharing works fine and they appear on the Win7 network map.However, they regularly lose contact with each other BUT they both remain able to access the Internet via the WAG160N and appear in its ARP/RARP table.
View 3 Replies
View Related
May 14, 2013
I have a DIR-655 Rev B1, FW 2.01 (I will probably upgrade the FW tonight to the latest.)
I have at least 20 items that connect wirelessly to this router (2 PCs, 2 Laptops, 2 Tivo Box, 3 Game Consoles, 3 Cell Phones, 2 Tablets, 2 TVs, Printer, AP Gateway, and some other projects) It's been a solid connection to everything for the past couple of years.
I bought a new Dell Inspiron 15r SE laptop (uses the Intel Centrion Wireless-N 2230 Wifi Solution.) After anywhere from 2 - 10 mins of browsing/watching a video/downloading files the access out to the internet simply stops.
At this point I'm still connected wirelessly to the router, and if I go to the router address I still have access and can login and see the router settings. I check and there's plenty of time left on the lease (days.) Still not getting internet access. Eventually my Laptop will disconnect and reconnect (or I do it manually.) I've performed hard resets of the router, I've had my laptop Forget the network and then reconnect, etc. Nothing has resolved it.
I thought it may be my laptop, but I've taken it to Starbuck, Work, Neighbors WiFi, etc and I don't have any problems staying connected on their networks.
I've had Dell on the line, we connected hardwired, and there solution was to force forget and reconnect to the router, which worked for the 10min he was on the line with me, but then failed soon after, and back in the same connectivity hell
View 4 Replies
View Related
Mar 17, 2013
I have an e4200 with the latest firmware 2.1.39. I just upgraded the firmware due to connection issues with my DSL. I now have the same issues with disconnects but I believe they are being caused by a different issue. When I try and log into my router through the IP address it wont let me, it says it can't find the router. Eventually after getting in the first time by using the default password, I have twice found out that all my settings are gone. This has happened twice this week and only happened after upgrading the firmware but I can not tell if firmware is causing it or if it is hardware related. I now reboot and restore saved firmware but that is a hassle and am pretty sure that is not the way it was designed to work.
View 9 Replies
View Related
Aug 1, 2011
I am now on my second E4200... But still the same failure.. It looses the internet connection 5-6 times a day, and then I have to switch it off and on to get connection again.
View 9 Replies
View Related
Nov 19, 2012
I have an EA4500 router. It's the latest in a long line of Linksys routers I've owned and I'm pretty familiar with setting one up and making changes. But the EA4500 seems a bit more picky than previous routers. Last night I tried to enable port forwarding for ports 53, 80, and 88 for my xbox. I already had port 3074 forwarded. When I did that and applied the change, I lost all Internet connectivity. I tried cycling the power on the router with no luck. I finally got connected again by going to 192.168.1.1 and disabled those ports. The status page then said I had Internet connectivity but I really didn't at least right away. It took a couple minutes before I was actually able to to connect to the Internet again. What else should I check when it says I don't have internet connectivity?
View 3 Replies
View Related
Apr 20, 2013
Updated firmware was installed and settings were reviewed. Intermittently the E1500 looses its ability to connect only to our Android devices and "Cisco Connect" displays that it has lost Internet connectivity. The PC hard-wired to the E1500 and another PC connected wirelessly both work fine when this happens, despite the Cisco Connect message. The Android devices show the presence of the network, but they never "connect" - find the IP address. The problem can only be resolved by re-booting (powering off/on) the E1500. The loss of connectivity to our two Android devices and the Cisco Connect error display always are concurrent. E1500 looses connection to Android devices
View 9 Replies
View Related
May 7, 2012
I upgraded my Linksys from 160n router to 4200V2 router. I configured 3 wireless Linksys webcams and they work fine. After 24hrs they i cannnot connect the via HTTP and webcames IP addresses disapear from the DHCP client table. If reboot the webcames the it works fine for next 24hrs. I did not make any modification to any settings and the setting looks just like i had on the 160N router
View 1 Replies
View Related
Jan 14, 2011
[url]...
One poster gives the password which is arbitrarily substituted but when I tried that (having had the same problem), I couldn't get it to work and had to reinstate factory settings and repeat the configuration from scratch.Now, for some reason, I can't even do that anymore! 'admin/admin' is no longer accepted, and if instead I try to open the configuration using the Setup Wizard CD I get an error message saying "Unable to connect..." and telling me to press the 'reset' button (which I have of course done, to no avail). Yet pinging the router produces an immediate successful response and my access to the internet is as before.
View 3 Replies
View Related
Sep 8, 2011
i have a WUSBF54G that will connect to my router just fine. Right when the device is first plugged in there aren't any problems. I can ping my router, I can ping google.com. The browsers all work correctly, etc. But after a while, maybe 30 minutes (it varies) I lose the connection to the internet. I can still ping the router. I can ping other devices on my network. But I cannot ping any websites by DNS name or by IP address and any browser I use won't display any websites. I have other wired and wireless connections on this network that don't have any problems. I even unplugged this adapter and plugged it into a different computer and had similar results. The device is relatively new (maybe a month old, but only used a few times within that month, and the use that it did get is mostly from trying to troubleshoot this issue.) Both computers I have installed the device on are running Windows 7 Ultimate. Both computers have the latest drivers installed from this site:
[URL]
I have a netopia 3000 router and I have checked to see if the problem could be caused by this router but there is nothing out of the ordinary there. All of my troubleshooting has been using the Win 7 "network and sharing center" to connect. I couldn't get the linksys connection tool to work and actually, I noticed after reading this forum that the linksys wifi connection tool doesn't work with win 7 after all so I don't think using the built in win 7 wifi tools would cause the issue. Also, just to clarify, in an attempt to resolve the issue I have tried dynamically assigning an IP address for this connection and also a static IP address. Either method seemed to yield no results. It is a frustrating problem to say the least. I don't want to believe that the adaptor is faulty. As I said it is relatively new. Also, as I mentioned, when I first plug it in it will work correctly for about the first half hour or so before it will stop reaching the internet. I then have to physically unplug the device and plug it back in in order to correct the issue. I was thinking of creating some kind of script that will automatically disable the adapter every 30 minutes and then enable the adapter. I ran into another issue here though. If I disable the adaptor (either from device manager or from "Network Connections) the device will change status from "Not Connected" to "Disabled." So far so good. But then, when I go to enable the adaptor again the adaptor disappears from the list. It's as if it isn't plugged in any more. The only way to get it back is to physically unplug the device and physically plug it back in. How to "Enable" the device without it disappearing from the network adapter list.
View 1 Replies
View Related
Jun 30, 2012
I have a wireless router which is connect to a DSL modem. Everything was working fine but now the wireless router looses connection often and if i remove the RJ45 check from my wireless router and plug it in after few minutes it works but again it looses connection.
View 2 Replies
View Related
Mar 1, 2013
Region : UnitedStates
Model : TL-WR1043ND
Hardware Version : V1
Firmware Version : 3.13.12 Build 120405 Rel.33996n
ISP : AT&T
Every 5 to 7 days my router loses connection with WAN (ISP modem) but connection over LAN is fine. It seems that 1043ND tries to connect to DSL modem from AT&T by username and password (that does not exists) instead of doing Dynamic IP. I understand that AT&T modem is of type of PPPoE but there is not a password or user id and connection must be dynamic. Page 192.168.0.1/logininfo of modem complains that I was trying to login with incorrect user id password. Every time I have to
1- connect the modem directly to my computer so the modem resets.
2- I have to reset 1043ND to factory default, reboot, and connect cables back how they were, Then go to WAN page do a release and renew to get connected to WAN again.
View 2 Replies
View Related
Mar 11, 2011
i'v recently bought a WAG120N for my home and set it up after that i checked that my wireless link speed on my laptop is 72mbps instead 150mbps after a few googling ive found that 150mbps is only avalaible on 40MHz radio band but in setup page i only found 20MHz.
View 2 Replies
View Related
Jan 16, 2011
I'm running Windows 7 64 bit with a Linksys WAG 320N modem.
The last few days my internet disconnects every night at roughly 12:30. I have checked my wireless drivers in devices and the part to automatically disconnect is unticked.
I can't find anything in the modem to automatically shutdown
View 6 Replies
View Related
Sep 5, 2008
I have a linksys system WRT54G at home. I had no problems with the Linksys router until about a month ago when I decided to make it a secure network. I run three computers of the wireless router (1 desktp and 2 laptops) Since making the wireless network secure I can not connect with my business laptop IBM Thinkpad X40, but thother e computers work just fine.
View 8 Replies
View Related
Jul 22, 2011
problems when I wanted to connect my laptop to my WAG120Nrouter for the first time.First the wireless adapter on my windows xp gives me the error "unable to verify your identity"second when i passed the security verification by bypassing the security options on the connection properties of the adapter, windows tries to acquiring network address and continues it for hours. Seems Windows cannot get any ip address from the router.The router works fine with wired Ethernet devices and my iPhone when i connect it wirelessly.
View 1 Replies
View Related
Sep 30, 2011
I have copied my computer's time in the router time setup under Time in the "tools" section of the router setup. After a few days of the router being up without a hard restart, it has lost 10 minutes somehow. I went to the logs and cleared them out and then looked at the entry showing that the log was cleared and looked at my computer clock and the time stamp of the log entry, and it was 10 minutes slower than my computer clock that I had originally set it from. I have a clock plugged in by the computer, and my computer always matches the clock that it plugged in, so I know it isn't my computer loosing time. What is going on here? Why does the router loose the correct time after it has been up and not unplugged or rebooted at all? I know that the router will loose the time if you unplug it, but this isn't the case here.
View 5 Replies
View Related
Apr 10, 2012
I have a WES610N in my office connected to a E4200 @ the cable modem in the family room. ~30'.The connection is fine and works well when working.Connected to the WES610N I have:
-Polycom VOIP phone
-HP Mediasmart Windows Home Server
-Desktop
-Multi-Function Laser Printer
I have two issues.
1) The Polycom does a random reboot that I have traced down to it loosing it's IP
2) The Windows Home Server looses it's IP requireing a hard reset.
I have enabled QOS for the polycom and that just worked with managing data. However both devices seem to loose their IP regularly. The desktop might also be having the issue but because it is Vista I suspect Vista is better equipped to deal with IP issues.
View 9 Replies
View Related
Apr 18, 2012
I bought my WAG320N 1 year ago, in this time i tried to connect in wireless mode many times, but I can' see the SSID that I have created from my laptop and from my palm. At the beginning, when the router was new i saw 2 or 3 times the SSID for 2 minutes, and after this time the SSID disappear. Is my WAG320N damaged?
View 5 Replies
View Related
Jul 24, 2011
Just recently im having trouble connecting to the wireless Using my hp laptop. The Wireless Was previously working fine though recently, has stopped working, all the other devices on the wireless network work fine (Asus Laptop, Iphone's etc). The hp laptop has no problem in connecting to the neighbours wireless and picking up a signal, however, when i go to search for the WAG320N im unable to find it in the list, sometimes it does appear, but after double clicking has trouble connecting to the wireless and will then dissapear from the list. I have tried manually entering the SSID and Password and seeing if it would connect, and also manually entering the IP address however no luck, no other device on the network has trouble finding the broadcast Signal Apart from the HP DV6-3139TX
View 1 Replies
View Related
Mar 20, 2012
in my network i got a switch with 4 vlan's configured
-vlan 10
-vlan 20
-vlan 30
-vlan 40
in vlan 40 i have my domain controller for my existing domain.i have read that seperate vlan's can't have contact without a lollipop router ( router on a stick, inter vlan routing)i want that users in vlan 10, vlan 20 and vlan 30 can have access to my domain controller in vlan 40
but they can't have access to each other.
View 11 Replies
View Related
Apr 27, 2011
Newly purchased DSC-930L connected to DIR-625. Firmware is 1.0 for DCS-930L and A1-1.09 for DIR-625.Camera works fine when connected with cable. Wireless enabled, fixed IP address.Unplug cable and camera still works fine for a while: can access the view page and view picture that does change. F5 refreshes page no problems. After a while (about 5 minutes) web page no longer reachable by browser. Reconnect cable and works fine, unplug and repeat the cycle same thing happens.Also tried: unplug ethernet cable, unplug power cable, wait 10 seconds, connect power cable, try to browse to camera - cannot reach camera.
View 13 Replies
View Related
Feb 24, 2012
I have a WAG160N wireless gateway . Yesterday when i tried to power it on after a couple of seconds the power led was solid green and the Ethernet leds were blinking with no Ethernet cable attached to the router . The ethernet leds would keep blinking for minutes . I tried to use a screwdriver to do a hardware reset ( with power on ) and i noticed that the power led would start blinking green/red for minutes . I tried to use another wired router which i have for backup and it could connect to the internet normally without a problem.
What the green / red blinking power led means ( power led is green and then changes to red and then it starts over ) ?
View 1 Replies
View Related
Mar 23, 2012
I can't get a new IP from my ISP when my Cable modem router(EPC3925) is set to router mode, i have tried factory restore, unplugged etc..but still no luck. It changes each time i reset it when i set it to bridged only mode but then i won't be able to connect other devices to it since it doesn't uses DHCP in bridged only mode. It changes back to the IP i had when i set it to router mode. I don't want to change my router settings to bridged only because it would disconnect the other devices in my house. Why my ISP assigns the same IP address when it's set to router mode but assigns different IPs when it's set to bridged only, how is this possible ?
View 1 Replies
View Related
Feb 14, 2011
i have a DSL connection which is established using a dial-up (PPPoE) modem. I recently bought a wifi router, and I found that when I plug the cable to one of the LAN ports and the laptop, it seems as if it wasn't connected at all (not detected on either side).I tried to format the system running on XP and I installed windows 7 but the problem persists.The only thing I can think of right now is using a crossover cable, but I somehow doubt that it should work since I tried plugging the router to my netbook (using a normal cable) and it worked like a charm. But maybe the fact that it's a quite old laptop (PB MV51-101) has something to do?
View 8 Replies
View Related
Aug 27, 2012
We have some 1242 LAPs in a two 5508 controller setup working fine. All LAP are configured to obtain address from DHCP. After first join we usually change some configs like HOSTNAME, AP GROUP, PRIMARY AND SECONDARY WLC. After a software restart or a complete power off/power on the LAPs joins the primary controller and all configuration still there. We now add a 1142 LAP and is does not retain the configuration after a power off/power on cycle, but after a software restart there is no problem. The only way to retain the config is setting the AP with a static IP address.
We use WLC 7.0.116 and we see no errors in the LAP console.
View 1 Replies
View Related
Jun 30, 2011
TOSHIBA LAPTOP WITH WINDOW 7 - The LAN port on my laptop does not show a light when the cable is plugged in?
View 1 Replies
View Related
Mar 14, 2013
Our family has about three computers that use a wireless network that we all share. We have an old Gateway, a WCG200, that is bridged to an E2000, which was set-up ever since we required better security when someone used our connection to illegally obtain movies. We got a letter which warned us of any future violations that could cause legal action, so we looked into our wireless connection to better secure it from any other individuals outside of our household. The WCG200 is connected to the outlet in the wall via cable, and then connects from the Ethernet to the E2000. The E2000 has a stronger security setup than the WCG200, which is the advice we received from our ISP and would allow us to keep the Gateway. It provides a strong signal, but from time to time, we suffer latency or slow loading through all of our online devices, even though our connection speed displays a solid 72.0 Mbps. I've tried the Event Viewer to see any problems, and I have noticed some small things:
- WLAN AutoConfig service has successfully stopped.Wirel?
- WLAN Extensibility Module has stopped. Module Path: C:WindowsSystem32cmihvsrv64.dll
- The server {E10F6C3A-F1AE-4ADC-AA9D-2FE65525666E} did not register with DCOM within the required timeout.
- Broadcom NetLink (TM) Gigabit Ethernet: The network link is down. Check to make sure the network cable is properly connected. [This last one is strange, since I use the Wireless Network Connection with a DW1501 Wireless-N WLAN Half-Mini Card, while the Broadcom adapter is under the Local Area Connection and displayed as not connected.]
Other than that, I'm not quite sure what the recurring problem comes from. Our WCG200 has a firewall enabled and our E2000 has an SPI firewall enabled. The security mode of the E2000 is a WPA2 setup. We have disabled the wireless network of our WCG200 in order to make use of the E2000.
View 9 Replies
View Related
Dec 25, 2012
I am going to use my ethernet cable to connect my pc to my xbox to use the PC as a bridge for the connection. My one question is, when I go to the adapter settings and go to the sharing tab on the properties of my wireless, what does the check box named 'Allow other users to connect through this computer's internet connection' do?
View 4 Replies
View Related
Jul 28, 2012
I have an 871 set up at home with 2 VLANs, both of these vlans present a strange behavior where an user is unable to ping/contact another user on the same subnet, however if users are on different subnet it seems to work [code]
According to the troubleshooting that I have done, the issue seems to be with the broadcast traffic, ARP request/reply do not reach another host on the same subnet (wireless to wireless or wired to wireless) however if the wireless device iniciates the connection to wired, it works fine.
I have tried to enable proxy arp on the different VLANs and BVI and different combinations but no sucess in order to get traffic across 2 wireless devices on the same subnet or a connection that is iniciated for a wired client to a wireless one.
I tried enabling and disabling dot11 arp-cache but no luck.
View 2 Replies
View Related
May 4, 2012
My WAG120N wireless router disconnects every hour, precisely at the same time. This problem has started a few days ago, until then everything was fine.When the connection is gone, the "Internet" light goes off, the other lights remain on. For example, it disconnects at 07:30. It takes a minute or two to reconnect. Then it disconnects at 08:31. It reconnects, and then disconnects at 09:32.. and so on.Here are the things that I have tried (with my limited knowledge.. I'm not good with technology):- Turned the power on/off. No matter what time I do this at, the router disconnects at the same time again. For example, if it last disconnected at 07:30, and I turn it off and on at 7:50, it still disconnects at 08:31.- I tried resetting it, by pushing and holding the reset button on the back for 30-60 seconds (did it several times). Reconfigured the router (manually, not from a backup config file). Same situation as above, disconnects at the same time as always.
- I upgraded the IOS to v1.00.16, which I found here: [URL] reset and then reconfigured again. Still it didn't work.- Looked in the configuration pages for any values that resemble a 60 minute time span, and changed them. Only thing I found was the security key renewal period. Or was I sold a faulty product?
View 6 Replies
View Related
