I have a wireless router which is connect to a DSL modem. Everything was working fine but now the wireless router looses connection often and if i remove the RJ45 check from my wireless router and plug it in after few minutes it works but again it looses connection.
View 2 RepliesI am now on my second E4200... But still the same failure.. It looses the internet connection 5-6 times a day, and then I have to switch it off and on to get connection again.
View 9 Replies View Relatedi have a WUSBF54G that will connect to my router just fine. Right when the device is first plugged in there aren't any problems. I can ping my router, I can ping google.com. The browsers all work correctly, etc. But after a while, maybe 30 minutes (it varies) I lose the connection to the internet. I can still ping the router. I can ping other devices on my network. But I cannot ping any websites by DNS name or by IP address and any browser I use won't display any websites. I have other wired and wireless connections on this network that don't have any problems. I even unplugged this adapter and plugged it into a different computer and had similar results. The device is relatively new (maybe a month old, but only used a few times within that month, and the use that it did get is mostly from trying to troubleshoot this issue.) Both computers I have installed the device on are running Windows 7 Ultimate. Both computers have the latest drivers installed from this site:
[URL]
I have a netopia 3000 router and I have checked to see if the problem could be caused by this router but there is nothing out of the ordinary there. All of my troubleshooting has been using the Win 7 "network and sharing center" to connect. I couldn't get the linksys connection tool to work and actually, I noticed after reading this forum that the linksys wifi connection tool doesn't work with win 7 after all so I don't think using the built in win 7 wifi tools would cause the issue. Also, just to clarify, in an attempt to resolve the issue I have tried dynamically assigning an IP address for this connection and also a static IP address. Either method seemed to yield no results. It is a frustrating problem to say the least. I don't want to believe that the adaptor is faulty. As I said it is relatively new. Also, as I mentioned, when I first plug it in it will work correctly for about the first half hour or so before it will stop reaching the internet. I then have to physically unplug the device and plug it back in in order to correct the issue. I was thinking of creating some kind of script that will automatically disable the adapter every 30 minutes and then enable the adapter. I ran into another issue here though. If I disable the adaptor (either from device manager or from "Network Connections) the device will change status from "Not Connected" to "Disabled." So far so good. But then, when I go to enable the adaptor again the adaptor disappears from the list. It's as if it isn't plugged in any more. The only way to get it back is to physically unplug the device and physically plug it back in. How to "Enable" the device without it disappearing from the network adapter list.
Region : UnitedStates
Model : TL-WR1043ND
Hardware Version : V1
Firmware Version : 3.13.12 Build 120405 Rel.33996n
ISP : AT&T
Every 5 to 7 days my router loses connection with WAN (ISP modem) but connection over LAN is fine. It seems that 1043ND tries to connect to DSL modem from AT&T by username and password (that does not exists) instead of doing Dynamic IP. I understand that AT&T modem is of type of PPPoE but there is not a password or user id and connection must be dynamic. Page 192.168.0.1/logininfo of modem complains that I was trying to login with incorrect user id password. Every time I have to
1- connect the modem directly to my computer so the modem resets.
2- I have to reset 1043ND to factory default, reboot, and connect cables back how they were, Then go to WAN page do a release and renew to get connected to WAN again.
Updated firmware was installed and settings were reviewed. Intermittently the E1500 looses its ability to connect only to our Android devices and "Cisco Connect" displays that it has lost Internet connectivity. The PC hard-wired to the E1500 and another PC connected wirelessly both work fine when this happens, despite the Cisco Connect message. The Android devices show the presence of the network, but they never "connect" - find the IP address. The problem can only be resolved by re-booting (powering off/on) the E1500. The loss of connectivity to our two Android devices and the Cisco Connect error display always are concurrent. E1500 looses connection to Android devices
View 9 Replies View RelatedI upgraded my Linksys from 160n router to 4200V2 router. I configured 3 wireless Linksys webcams and they work fine. After 24hrs they i cannnot connect the via HTTP and webcames IP addresses disapear from the DHCP client table. If reboot the webcames the it works fine for next 24hrs. I did not make any modification to any settings and the setting looks just like i had on the 160N router
View 1 Replies View RelatedI have an EA4500 router. It's the latest in a long line of Linksys routers I've owned and I'm pretty familiar with setting one up and making changes. But the EA4500 seems a bit more picky than previous routers. Last night I tried to enable port forwarding for ports 53, 80, and 88 for my xbox. I already had port 3074 forwarded. When I did that and applied the change, I lost all Internet connectivity. I tried cycling the power on the router with no luck. I finally got connected again by going to 192.168.1.1 and disabled those ports. The status page then said I had Internet connectivity but I really didn't at least right away. It took a couple minutes before I was actually able to to connect to the Internet again. What else should I check when it says I don't have internet connectivity?
View 3 Replies View RelatedI have a DIR-655 Rev B1, FW 2.01 (I will probably upgrade the FW tonight to the latest.)
I have at least 20 items that connect wirelessly to this router (2 PCs, 2 Laptops, 2 Tivo Box, 3 Game Consoles, 3 Cell Phones, 2 Tablets, 2 TVs, Printer, AP Gateway, and some other projects) It's been a solid connection to everything for the past couple of years.
I bought a new Dell Inspiron 15r SE laptop (uses the Intel Centrion Wireless-N 2230 Wifi Solution.) After anywhere from 2 - 10 mins of browsing/watching a video/downloading files the access out to the internet simply stops.
At this point I'm still connected wirelessly to the router, and if I go to the router address I still have access and can login and see the router settings. I check and there's plenty of time left on the lease (days.) Still not getting internet access. Eventually my Laptop will disconnect and reconnect (or I do it manually.) I've performed hard resets of the router, I've had my laptop Forget the network and then reconnect, etc. Nothing has resolved it.
I thought it may be my laptop, but I've taken it to Starbuck, Work, Neighbors WiFi, etc and I don't have any problems staying connected on their networks.
I've had Dell on the line, we connected hardwired, and there solution was to force forget and reconnect to the router, which worked for the 10min he was on the line with me, but then failed soon after, and back in the same connectivity hell
I dont know why this keeps happening, It was a problem last summer and now its happening again. My modem looses connection and only a few lights are on. Im using comcast in the DC/Metro area and Im using a telephone modem.
View 12 Replies View RelatedI have a server (Windows Server 2003) that randomly looses connection with the default gateway and anything on the outside. When this happens, the server cant ping the gateway (A Juniper SSG5 firewall/router) and the gateway cant ping the server. But the server still can ping anything else on the network and everything inside the network works fine with it. The most reliable remedy is to reboot the router. Rebooting the server or resetting the network card sometimes works. I have tried both onboard network cards and a separate PCI network card on the server. There are no router log entries that correspond to the problem. This server is used as a Terminal Server for a remote office and as a file server.
View 1 Replies View Relatedwrt54gs connects but after about a minute it looses connection and boots continuously
View 1 Replies View RelatedMy new RVS4000 (2.0.2.7) connects the WAN via PPoE with dynamic IP which is held at DynDNS and normally I see the RVS4000 via a router-to-router-VPN. That works fine so far, but every "some" days the router looses WAN connection (and with ist VPN). When this happens, last DynDNS-update is hours ago, so it didn`t reconnect. Looking on the routers site, the LAN is fully functional for clients that have got their DHCP-Information. New clients don`t get DHCP-Info (IP-address, DNS), both do not have internet access. The router`s WAN-summary shows, that it thinks to be "CONNECTED" but with empty WAN-IP and DNS entries. Klicking "DISCONNECT" and then "CONNECT" again solves the problem so far. The loss of connection is not the periodic break from the IPC, which is correctly identified and reconnected as configured. I wanted to trace the problem with the log, but there is also a bug. It stops logging at some time completely - neither email-log nor local log, so I never happend to be lucky to hit the point of loss of connection. Also the local log provides a first and next pages, but the next pages are always empty - not really useful.
View 3 Replies View RelatedI recently started having trouble with my VPN clients loosing connection.I can create the conenction, work with it for a while, and then loose connectivity.Timing seems to be dependent on the activity over the connection.More activity, the conenction stops working sooner.
The cleint doesn't disconnect, I just can't access anything from the client.Disconnecting and reconnecting the client fixes the problem, temporarily depending on how much data I'm transferring.This works 90% of the time.The other 10% if I wait 30-45 minutes, and try again.. It works...with the same results...
It was originally isolated to a Win 2003 server that I was using as the client.It is now happening on my Win XP client as well.I'm using the AnyConnect client ver. 2.5.2014 with the VPN service on the UC520.Which I beleive, is similar to the ASA 5500 series VPN device.I am running ver 8.1.0 on the UC 520, and I can't remember if this started after upgrading to the new software.
I have an e4200 with the latest firmware 2.1.39. I just upgraded the firmware due to connection issues with my DSL. I now have the same issues with disconnects but I believe they are being caused by a different issue. When I try and log into my router through the IP address it wont let me, it says it can't find the router. Eventually after getting in the first time by using the default password, I have twice found out that all my settings are gone. This has happened twice this week and only happened after upgrading the firmware but I can not tell if firmware is causing it or if it is hardware related. I now reboot and restore saved firmware but that is a hassle and am pretty sure that is not the way it was designed to work.
View 9 Replies View RelatedI have a problem with my laptop...i have a Packard Bell laptop connected to my wireless router WAG 320n and it has been working fine until yesterday when it didnt connect automaticly as it have been doing before because i have my ssid network saved on my laptop!
I logged on to the router page and changed from standard channel to wide channel and also tried different channels at the same time that i tried connecting with the laptop but i get the same message everytime "Unable to connect!
I have copied my computer's time in the router time setup under Time in the "tools" section of the router setup. After a few days of the router being up without a hard restart, it has lost 10 minutes somehow. I went to the logs and cleared them out and then looked at the entry showing that the log was cleared and looked at my computer clock and the time stamp of the log entry, and it was 10 minutes slower than my computer clock that I had originally set it from. I have a clock plugged in by the computer, and my computer always matches the clock that it plugged in, so I know it isn't my computer loosing time. What is going on here? Why does the router loose the correct time after it has been up and not unplugged or rebooted at all? I know that the router will loose the time if you unplug it, but this isn't the case here.
View 5 Replies View RelatedNewly purchased DSC-930L connected to DIR-625. Firmware is 1.0 for DCS-930L and A1-1.09 for DIR-625.Camera works fine when connected with cable. Wireless enabled, fixed IP address.Unplug cable and camera still works fine for a while: can access the view page and view picture that does change. F5 refreshes page no problems. After a while (about 5 minutes) web page no longer reachable by browser. Reconnect cable and works fine, unplug and repeat the cycle same thing happens.Also tried: unplug ethernet cable, unplug power cable, wait 10 seconds, connect power cable, try to browse to camera - cannot reach camera.
View 13 Replies View RelatedWe have some 1242 LAPs in a two 5508 controller setup working fine. All LAP are configured to obtain address from DHCP. After first join we usually change some configs like HOSTNAME, AP GROUP, PRIMARY AND SECONDARY WLC. After a software restart or a complete power off/power on the LAPs joins the primary controller and all configuration still there. We now add a 1142 LAP and is does not retain the configuration after a power off/power on cycle, but after a software restart there is no problem. The only way to retain the config is setting the AP with a static IP address.
We use WLC 7.0.116 and we see no errors in the LAP console.
I'm trying to configure ACS 5.2 so that should it loose connectivity to Active Directory it chooses the local authentication, however I can't seem to make this work.Within ACS 5.2, Access-Policies, Access Services, Default Device Admin, Identity,
I have a single rule configured for any device that matches tacacs to use the identity source of Active Directory,
If authentication failed: Reject
If user not found: Reject
If process failed: Drop
The ACS can not access Active Directory, when I debug TACACS authentication on any 65k or 2921 device I get "Received Authen status error".
I just purchased a Vizio Dual-Band HD wireless internet router, completed the steps on the quick start guide and I can get internet connection using my desktop but I cannot get internet connection using my MacBook. I went to [url]... and in the top right corner, it says "Offline" on the router. How do I make it say "Online"?
[code]....
my router has intermet but i cannot get a connection to my computerbut its not just my computer my bfs computer our PlayStation nothing can connect to it right now i tried going in network and settings and diagnosing it and i tried unplugging the motem amd all the wires nothing is working. Two of the lights on the motem are green one is orange the wirless is lighting up blue. This is not the first time either....it came back after a while last time but now its not.
View 3 Replies View RelatedMy main Internet connection is a frontier modem /router It is on the main level of the house. In the basement I am trying to set up the cisco E3000 through an Ethernet cable.
View 4 Replies View RelatedSomething strange is happening to my Cisco 1941W. Every time I reboot the router i loose the running configuration of the service-module (Access Point module). The weird thing is that the router's configuration remain the same. I made sure i save the configuration by issuing the wr command on the service module console but still happens. My router's current IOS version is 15.0(1)M1 and my AP's is 12.4(21a)JA1.
I also did another test by making sure the startup-configuration was identical to the running configuration and when I reload the router still happens.
I want to share my wireless connection witch is coming from distant internet provider, to my desktop computer with wireless adapter. I have tplink wireless router witch is connected trough wan port to my lan network card also in desktop computer.So is there something wrong with this setting because i can not properly finish wireless router auto configuration wizard, it always return my error.
View 1 Replies View Relatednormally insert the D-link CD in my computer and then follow the steps. this time in the step that all connectivity was being checked the message appeared that one of the cables (ethernet or the other one) is not connected whereas I am quite sure that they are properly connected and nothing at least as far as I know is wrong.after several times, I could connect to the wirelss connection but actually there was no internetwhen I also tried with cable directly from wall jack to my computer it was also the same case.
View 4 Replies View RelatedI am trying to use my pc's internet connection that I am getting from a cricket wireless device to go to a linksys wrt54g router. I believe it should be possible to enable ICS and hook up a cable from the nic on the pc to the wan port on the router but have not been able to get it to work so far.
View 6 Replies View RelatedWe have highspeed internet that comes in at our house, but we want internet in our shop. We have a wireless dongle outside of the building and it picks up the signal for the main computer from the main wireless router. Because it is a metal building we cannot get a wireless signal inside the building otherwise. I want to hook a wireless router up to the computer in the shop, share the internet connection, and broadcast the signal throughout the shop so I can use wireless in the shop.
View 1 Replies View RelatedI have 1 mbps internet connection and I got two computers to be connected. optimum configuration of the router required.
View 5 Replies View RelatedMy F5D8235-4 v3 constantly looses it's DHCP service and needs to be rebooted.
View 1 Replies View RelatedI bought a Prolink Wireless Router WGR1004 and I have problem connecting it with internet. My windows able to detect and connect to the Wireless connection but the internet browser cannot display any webpage. I have a Linksys WB300 ADSL Modem when wired to my pc it pings IP 192.168.1.3 , default gateway 192.168.1.1 My connection to Wireless pings IP 192.168.1.2, default gateway 192.168.1.1ADSL phone cable connected to my modem and Ethernet cable linked from Modem to Internet Port of Wireless router. Settings in Network Connections=>properties=>TCP/IP=>Obtain an IP address automatically and obtain DNS Server address automatically. Web browser connections settings=>Internet Options=>Lan settings=>Automatic detect settingsRouter Configuration=>Lan IP address is 192.168.1.254 Internet IP address is 192.168.1.2, Security and SSID are working properly. The problem is my web browser cannot display webpage.
View 1 Replies View RelatedJust moved into apartment in Ann Arbor and am forced to use this ISP. They are not wireless friendly. Their manual sucks and will only provide tech support for $80/hour. I bought a Belkin router and got it working for my MacBook. BUT my roommate can't connect, even tho her MacBook sees the network. And I can't print to my wireless printer even tho it says everything is fine when I run the wireless diagnostics.The ISP has these rules:
- Only connect the router to the Internet or Wan port. Do not connect to the numbered ports (how do I know whether or not I've done that?)
- Do not use static IP addresses
- Do not run a DHCP server
I recently had to unplug my Linksys WRT54GL wireless router when doing some rearranging and now i'm unable to get a internet connection. I've confirmed the modem is actually working by connecting my laptop directly (which worked), but when I connect the Linksys WRT54GL wireless router to my modem the internet connection goes away. The connection is lost when connected via wireless and hardwired to one of the back ports. I've tried resetting the modem, router and computer and read every forum out there trying to find something, but i'm still stuck.
View 5 Replies View RelatedWe have Comast internet using an Arris modem and have a Netgear wireless router. We have our modem hooked up to a desktop computer that we don't even use. We have three laptops that we us with our wireless.Comcast has told us that we have to have the modem hooked up to the desktop for the internet to work.what do people do who have only a laptop and have wireless internet in their house?Is there anyway to get rid of the desktop and have the modem hooked directly to the cable and router?
View 4 Replies View Related