Wireless Router For 1 Mbps Internet Connection?
Jan 25, 2012I have 1 mbps internet connection and I got two computers to be connected. optimum configuration of the router required.
View 5 Replies
ADVERTISEMENT
Linksys Wireless Router :: WRT54G - .77 Mbps Download And .17 Mbps Upload Speed
Mar 11, 2013I just ran some speedtests om my PC on the advice of my isp to see if my Linksys WRT54G router might be bad. As a result, I found that the router might not be entirely bad, but it might not be entirely good, either. I got .77 Mbps dowload and .17 Mbps upload on the first speedtest. I got .43 Mbps download on the second speedtest and the speed test hung hear the end. When I connected an IMac to the cable modem with an ethernet cable, the IMac ran strong. So the tech thought I should get a new router.
But wait a minute, isn't there a network adapter in the PC that the router talks to? Might the adapter be the problem, not the router? So I speedtested the wireless network to the IMac. That speedtest was fine, tiptop, like the ethernet direct connection test noted above. Did that tell me that the problem is in my PC network adapter, not the router? Then, I retested (speedtested) the connection on the PC and it was fine...excellent. Good up and down speeds, no hangs.Then, I checked the PC adapter (a Belkin). I saw three adapters on Device Manager, including the Belkin. I downloaded new drivers for the adapters (except for the Microsoft Virtual WiFi Minipoty Adapter - because it got a warning that the download software wasn't signed and might harm my computer).
Linksys Wireless Router :: E4200 Slow Speeds / 54 Mbps Wifi And 100 Mbps On Wired
Dec 22, 2011So I have installed my new E4200 version 1 and I am disappointed with the speeds. My computer has a wireless N card and gigabit Ethernet compatibility. I am currently getting a miserly 54 mbs wireless and 100 mbs on the wire (connected with cat6 all the way)... Anything I should try to get close to advertized speeds?
View 9 Replies View RelatedLinksys Wireless Router :: WRT150N Is A 300 Mbps Or 150 Mbps?
Mar 15, 2013Which is the wireless speed of this router? No speed infos are present in the official web site. In the web some sites say it's a 300, others say it's a 150, others 248...
View 9 Replies View RelatedD-Link DIR-825 :: 300 MBPS Connection Drops To 150 Mbps
Mar 7, 2011300 M bps drops to 150 M bps when it recycle power. I met all requirements for 300 M bps connection this happen only in 2.4 g Hz Band width.
View 1 Replies View RelatedInternet Connection Below 1 MBPS?
Feb 26, 2013I was wondering why the heck I'm getting BELOW 1 mbps toward my internet connection? I look at my wireless signal, and it's full. yet, I go on speedtest and have about 0.20 mbps.
Info - My parents pay nearly $100 for this bundle thing with the internet, phone, and something else, I think TV.
provider - windstream
router - F@ST 1704
Also, the router is currently on top of the main computer in the office, on top of the router is a house phone.Yet, if I move the house phone, nothing changes. The computer is on the floor.Should i move it? Would this improve my connection?Even the main computer that's wired with the router gets the same mpbs as wireless.
150 Mbps Connection Drops To 72 Mbps
Jun 22, 2012I have a Netgear CG3100 modem hooked up to a Netgear WNR2000 router. Both are sending out signals, the CG3100 on channel 11 at 40 Mhz and the WNR2000 on channel 1 at 20/40 Mhz. I keep the WNR for legacy devices while the CG is for N devices only. They don't seem to interfere with each other much.Currently my computer is the only device connected to the modem wirelessly, with the only wired connection being the router. As I write this, the connection has actually dropped to 26 Mbps in the Wireless Network Connection Status window. I understand that this number drops under network load, but there doesn't seem to be any at the moment. If I go into the control panel and simply click apply, the connection jumps back up to 150 Mbps. However, this always drops back down, sometimes immediately, sometimes after a few minutes. It usually settles down at 72 Mbps, sometimes 54 Mbps.My wireless adapter is an ASUS PCE-N13 with v3.2.7.0 Ralink drivers. OS is Windows 7 64-bit.
View 6 Replies View RelatedCisco WAN :: 3845 WAN Speed - New Internet Connection 310 Mbps
Jan 1, 2012i have Cisco 3845 with 1 GB SFP, my company using fiber as backbone to isp, i have new internet connection 310 Mbps, does that enough ? does that for port only for LAN or also for WAN ?
View 8 Replies View RelatedLinksys Wireless Router :: E1000 Slows Internet (10 Mbps)
Jul 13, 2011Why my internet was so slow .90mbps. They got on my mac and changed the Ethernet setting to "manually" instead of "Automatic", then changed the speed to 10mbps instead of "autoselect". Now the internet is going at the 10mbps im supposed to be getting, but when i plug it into my router (wall>router>laptop) i get the .90mbps again. So do i how do i change the same setting on the router?
View 1 Replies View RelatedLinksys Wireless Router :: Wrt610n - 100 Mbps Speed Internet?
Jun 29, 2011I have Wrt610n V1 Firmware V 1.00.03 B15 and internet 300 mb.If i connect PC to my internet bridge i have 300 mb. But when I switch between a WRT610n all ports have ~100mb. In router I removes all check marks from all security, filter.
View 6 Replies View RelatedDoes Cable Modem Mbps Dictate Or Limit Router Mbps
Mar 1, 2012In other words. If my cable modem only has 50 mbps is that all I will get out of my wireless router, even if the router has a higher mbps rating/
View 8 Replies View RelatedLinksys Wireless Router :: EA4500 Slow Internet Speeds (Only 10 - 14 Mbps)?
Feb 5, 2013I am only getting 10-14 mbps when I should be getting 30-35 (using the gigabit ports). I thought it might be my provider but today I connected my old netgear router and the speed was 32-34 mbps. Is there some setting that I should be looking at?
View 5 Replies View RelatedLinksys Wireless Router :: EA2700 Signal Dropped To 5 Mbps / No Internet Access
Dec 8, 2012I've had this router for about 3 weeks. It's only 20 feet from the computer, but my computer on 2 or 3 separate days had trouble staying connected. The signal dropped to 5 Mbps and had a little yellow symbol that said no internet access and when I looked at the properties it said, "limited or no connectivity." I got impatient and purchased a 75 ft Ethernet cable online with plans to possibly return the router as I don't really need wireless anyways and since I spent $100 on this router I expect it to work at 20 ft distance.
For the last few days it has remained at 54 Mbps or more sometimes all the way up to 108 mbps. But now since it got pretty low a few times I don't trust it enough so I might return it anyways.IPv6 connectivity says no network access. This might be because when it asked for administrator password to recognize it as a trusted home network I closed it instead of putting in the password.
Wireless Gets 25 Mbps Down Speed And Laptop Gets Only 2.5 Mbps?
Jan 8, 2013I have a desktop and laptop here, the desktop being mine custom built wireless and all, and my buddies desktop.The issue that I'm having is that my desktop, regardless of wired or wireless gets 25 mbps down speed, and the laptop gets only 2.5 mbps down speed wired or wireless
View 4 Replies View RelatedWireless Connection Keeps Changing Mbps While Connected?
Sep 29, 2011I have a Linksys e2000 wireless router, my laptop connects fine, but as i keep hovering my mouse over the wireless icon in my system tray, it keeps changing Mbps from 130 at its highest going down into double digit Mbps, then back up to 130. Why wouldn't it stay connected at 130 all the time?Someone said to try lowering the beacon interval, fragmentation threshold, RTS threshold, and mtu size, but will doing that decrease the speed of my connection to the router?
View 5 Replies View RelatedD-Link DIR-655 :: Can't Handle 450 Mbps Wireless Connection
Mar 24, 2011I know that this Router of D-Link DIR-655 can't handle 450 Mbps Wireless Connection.
What is the newest D-Link Router available that can handle 450 Mbps Wireless Connection? Does the Network Wireless Adapters need to be change to achieve this?
TRENDnet 450 Mbps Wireless N Gigabit Router TEW-691GR (Piano Black)
[URL]
Rosewill RNX N300X Wireless Adapter / Connection Drops To 1 Mbps
Jun 29, 2012I have a Rosewill RNX N300X wireless adapter that keeps dropping to 1 mbps, and only goes up to about 18 mbps on a good day. How can I force a 54 mbps connection?
- I am running the latest drivers for the card.
- The network is "g", card accepts b/g/n.
- Another computer running RNX N360PC is getting a perfect connection on the same network.
Cisco WAN :: 2951 - Installation Of 2x4 Mbps MPLS Circuit And 1x8 Mbps Ethernet Link
Feb 18, 2013Installation of 2 x 4 Mbps MPLS circuit on primary router (CISCO 2951) and 1 x 8 Mbps Ethernet link on secondary router (Cisco 2951). We have successfully implement the primary router with 2 x 4 Mbps MPLS circuit. Site is having two computer room CR1 and CR2 and distance between both room is 200mts. CR1 is having primary core router and primary core switch where the service provider terminated the new MPLS circuit and we have done the successful implementation. CR2 is having Secondary core router and secondary core switch where we needs to have the termination of Ethernet link but service provider has delivered the Ethernet link on the CR1 which is incorrect DMARC Location.
Both the computer rooms are connected via optical copper can we use that copper to connect the circuit on CR2, as per my understanding we can use the optical fiber to connect the wind circuit on secondary router on CR2 by using the media connector.
D-Link DIR-655 :: 4 Mbps Upload Via CAT5 But Only 1 Mbps Upload Via N-format Wireless?
Jun 30, 2011I just upgraded my cable modem from the Motorola Sufboard 5120 to the DOCSIS 3.0 capable 6120. Provisioned it with Comcast and their "Blast" service (supposedly it caps at 16 down, 2 up).
I had, in the past, used my desktop via N-format wireless (DWA-525 N-format PCI adapter and DIR-655 N-format router) to do a speedtest.net test. I was getting 16 down and 2 up (as advertised). When I switched to the 6120, I did a speedtest.net test again to see what kind of gains, if any, I was getting. Turns out, I was getting 20+ down (nice improvement) and 1/2 Mbps up (a fourth of what I used to be getting?). Called Comcast. They "sent signals" (don't they always?) and claimed that it fixed it. My download speeds increased a smidge (about 22), but my upload speeds were still .5. Called Motorola, they had me do a few things and now I get 1 Mbps up and 27 - 30 down via wireless.
My download speeds are great. I'm content with that. If I hardwire from the cable modem directly to a ****py old laptop, a speedtest.net shows 4 Mbps up. So why do I get such a high upload speed when hardwired (4 Mbps), but a fraction of it (1/4th) when wireless? I'm not using any other devices to sap bandwidth (some are connected -- i.e. another desktop, my Droid phone, etc., but aren't actively pulling packets). And why would it go from 2 up (on my desktop via wireless in the past) to only 1 up (via wireless now) when the setup is the same across the board (as best I recall) other than upgrading my cable modem.
Since I get 4 up when hardwired straight off the cable modem, I assume my DIR-655 is slowing me down somehow. How to pick up the pace a bit? I've already tried the standard "power cycling", etc.
Oh, and the reason I go wireless -- my cable modem and wireless router are in my game room in the basement for my PS3. My desktop computer (and the wife's desktop computer) are two floors directly above it in our "office". Signal strength is "excellent" ... always has been. And again, pretty much everything is the same.
[URL]
1.01 Mbps Good Internet Download Speed For Wireless Laptop?
Aug 2, 2011I am working on an assignment for college and I was wondering if 1.01 mbps is a good internet download speed for a wireless computer?
View 1 Replies View RelatedD-Link DIR-615 :: AR9285 DWA-131 But Best Connection Is 150 Mbps
Jan 25, 2012I'm using an HP G60 laptop, running Win 7 Pro x64 SP1, fully patched. I'm usually in the home office, connected to a D-Link DIR-615 router (h/w: E3, f/w: 5.10, the latest). The internal Atheros AR9285 N150 wireless adapter has never been as reliable as I'd like, so decided to purchase a USB N300 adapter. I bought a TP-Link model for $10 and started using it. For some reason, it would only connect at 150, unless I ran the router's Web interface and saved the wireless settings, even without a change, at which point I'd see 300 Mbps. However, at the next restart after hibernation, the connection with the DIR-615 would fall back to 150.
I stepped on the TP-Link USB adapter and broke it. Oops. Decided to purchase a D-Link DWA-131 (h/w: A1, f/w: 1.21, the latest) 'cause it's compact and the box says that, "For Optimal Wireless Performance +Use With Wireless N 300 Router (DIR-615)."Expected 300 Mbps, but it connected at 65. Argh. Did the trick again with the DIR-615's Web interface, and saw 150. But after restart from hibernation, back down to 65. Unable to achieve 300 Mbps, unlike the cheap-o TP-Link adapter. Router is configured according to Lycan's sticky note. Router's Wireless Status shows a signal of 39%, and the router is in the next room in a wood-framed building.Is this as good as it can be? Looks like the DWA-131 is coupla years old with no new drivers for Win 7. Ran the DSL Reports Java speed test, and seeing 18+ Mbps d/l, and 1.8 Mbps u/l, which is about average from Cox here in The OC. If I can't get a faster connection, then D-Link's claim of "optimal performance" is misleading.
Home Network :: To Apply Qos To A 1.5 Mbps Connection
Dec 27, 2011Is there any reason to apply qos to a 1.5 mbps connection. i had comcast with a 15 mbps connection and qos was good for when downloading large files and gaming and all that at the same time. but i have moved and i only can get dsl at 1.5 mbps.
View 10 Replies View RelatedWhy Only 100 Mbps Wireless On New Linksys Router
Jul 24, 2012Contrary to what i have been reading, i have a DOCis 3 Modem, on Comcast, with an internet connection of 1GB. My wireless connections are in the 150-300 Mbps range thru a Linksys 4500N router
View 1 Replies View RelatedLAN Connection Speed 100 Mbps - Acquiring Network Address
May 12, 2012Recently, I am having an issue with my LAN connection. After I boot up, I get the "two computer" icon in my system tray that stays active. When I mouse over it, it says "Local Area Network Speed 100 Mbps Status - Acquiring Network Address"However, I am connected to the internet and there seems to be no connectivity problems. And it has an IP address: 192.168.1.66 This "acquiring network address" will persist forever, (although sometimes it will quit). If I right-click and do repair, the problem disappears immediately.I am running Win XP SP3 and am connected by ethernet cable to an ATT-U-verse Gateway.For what it's worth, Windows takes a very long time to boot up -- it takes a while for the icon to appear, and then the boot process completes.
View 1 Replies View Related100 Mbps On One Side Of Switch And 10 Mbps On The Other?
Feb 15, 2011I have 100 Mbps Half Duplex on one side of the Switch. ( Autonegotiation disabled )I have 10 Mbps Full Duplex on the other side ( Auto-negotiation disabled ). Should the link come up on both sides
View 4 Replies View RelatedIs There A Limit On Mbps For Windows XP On Wireless N Router
Nov 2, 2012I'm not able to connect at wireless n speed even though i have a wireless n adapter. i can force it but when i do my throughput drops dramatically, 20Mbps -> 1 Mbps. so i try, wpa2 security and can connect to router at 130 Mbps but throughput is 1Mbps when I throttle down connection to only connect at 54Mbps throughput is 20Mbps.
View 3 Replies View RelatedLinksys Wireless Router :: E3200 Only Getting 130.0 Mbps?
Jun 21, 2011after messing with it for a 2 days since I got it I cant seem to get more than 130.0 my last router had 300 same setup same distance
View 9 Replies View RelatedLinksys Wireless Router :: Only Getting 130 Mbps With E4200?
Dec 28, 2011I bought a Linksy E4200 yesterday and set it up fine, but I only seem to be able to get 130 Mbps on my Wi-Fi. I looked through these threads and tried disabling the 2.4Ghz band and it still remains at 130Mbps. There was no change, also read I can try set up a secondary SSID. I really don't know much about routers or configuring them
View 4 Replies View RelatedLinksys WRT54GL 802.11a/b/g Wireless Router - 15 Mbps ISP
Mar 16, 2011I currently own a LinkSys-WRT54GL 802.11a/b/g wireless router, and my ISP is Comcast Cable providing me with 15 Mbps (that's bits per second, I believe) download speed. I am wondering if there is any benefit with using an 802.11n wireless router to access the Internet? The maximum theoretical speed of the WRT54GL router is 54 Mbps (802.11g), which is faster than the 15 Mbps provided by my ISP.
I know that 802.11n has a max bandwidth of 300 Mbps, and it would work for intra- house transfers, such as streaming video from one computer to another.
But is there any benefit to 802.11n for Internet activity, such as web browsing, gaming, and streaming video from Netflix.
Cisco Switching/Routing :: 877 / 3750 - Sharing 10 MBPS Connection?
May 12, 2012I have a Router 877 and a switch 3750 also a 10 mbps internet connection and I want to share the internet connection to 5 different vlans with a maximum of 2mbps each one or 2 mbps guaranteed. The switch and the router are connected for a trunk port and the vlans are defined in both devices. I have tried many configurations of this with no success.
View 4 Replies View RelatedLinksys Wireless Router :: Cannot Reach To 450 Mbps With EA4500
Feb 8, 2013I have a new EA4500 router and I cannot configure it to reach the 450 mbps that is supposed to get.
I have it configured as follows:
Dual Band- 2,4 and 5 GHz
2,4 in 20MHz only - 5 GHz in 40 MHz only
2,4 Mixed - 5 Ghz only N
WPA2 personal in both
Channel - automatic (both)
I have checked that the 5 Ghz network can only use 4 channels: 36, 40, 44, 48. Where are the channels up to 100 (or more)? How to get all the power of the router?
Linksys Wireless Router :: WRT160N Speed Is Very Slow (0.5 Mbps)?
May 25, 2011I have the WRT160N. Using [URL], I can get 2.5Mps from wired ports, but less than 0.5 Mps using the wireless.
View 9 Replies View RelatedLinksys Wireless Router :: E1200 Speed Slows To 15 Mbps
Apr 29, 2013When I connect my modem directly to my computer I'm getting 27 MBPS speed. When I hook it up through my router, speed slows to 15 mbps.
View 2 Replies View Related
