Is there any reason to apply qos to a 1.5 mbps connection. i had comcast with a 15 mbps connection and qos was good for when downloading large files and gaming and all that at the same time. but i have moved and i only can get dsl at 1.5 mbps.
View 10 Replies300 M bps drops to 150 M bps when it recycle power. I met all requirements for 300 M bps connection this happen only in 2.4 g Hz Band width.
View 1 Replies View RelatedRecently, I am having an issue with my LAN connection. After I boot up, I get the "two computer" icon in my system tray that stays active. When I mouse over it, it says "Local Area Network Speed 100 Mbps Status - Acquiring Network Address"However, I am connected to the internet and there seems to be no connectivity problems. And it has an IP address: 192.168.1.66 This "acquiring network address" will persist forever, (although sometimes it will quit). If I right-click and do repair, the problem disappears immediately.I am running Win XP SP3 and am connected by ethernet cable to an ATT-U-verse Gateway.For what it's worth, Windows takes a very long time to boot up -- it takes a while for the icon to appear, and then the boot process completes.
View 1 Replies View RelatedI have a Netgear CG3100 modem hooked up to a Netgear WNR2000 router. Both are sending out signals, the CG3100 on channel 11 at 40 Mhz and the WNR2000 on channel 1 at 20/40 Mhz. I keep the WNR for legacy devices while the CG is for N devices only. They don't seem to interfere with each other much.Currently my computer is the only device connected to the modem wirelessly, with the only wired connection being the router. As I write this, the connection has actually dropped to 26 Mbps in the Wireless Network Connection Status window. I understand that this number drops under network load, but there doesn't seem to be any at the moment. If I go into the control panel and simply click apply, the connection jumps back up to 150 Mbps. However, this always drops back down, sometimes immediately, sometimes after a few minutes. It usually settles down at 72 Mbps, sometimes 54 Mbps.My wireless adapter is an ASUS PCE-N13 with v3.2.7.0 Ralink drivers. OS is Windows 7 64-bit.
View 6 Replies View RelatedI have ADSL modem in my workplace that is connected to a switch and other workplace computers are connected to this switch so the ADSL internet is shared in LAN network.(in each of computer I set default Gateway to ip of modem .....)I want to dial my workplace from home and then use of workplace internet or connect to workplace LAN.(such as VPN or Port Forwarding or I don't know...)
View 11 Replies View RelatedI just ran some speedtests om my PC on the advice of my isp to see if my Linksys WRT54G router might be bad. As a result, I found that the router might not be entirely bad, but it might not be entirely good, either. I got .77 Mbps dowload and .17 Mbps upload on the first speedtest. I got .43 Mbps download on the second speedtest and the speed test hung hear the end. When I connected an IMac to the cable modem with an ethernet cable, the IMac ran strong. So the tech thought I should get a new router.
But wait a minute, isn't there a network adapter in the PC that the router talks to? Might the adapter be the problem, not the router? So I speedtested the wireless network to the IMac. That speedtest was fine, tiptop, like the ethernet direct connection test noted above. Did that tell me that the problem is in my PC network adapter, not the router? Then, I retested (speedtested) the connection on the PC and it was fine...excellent. Good up and down speeds, no hangs.Then, I checked the PC adapter (a Belkin). I saw three adapters on Device Manager, including the Belkin. I downloaded new drivers for the adapters (except for the Microsoft Virtual WiFi Minipoty Adapter - because it got a warning that the download software wasn't signed and might harm my computer).
Installation of 2 x 4 Mbps MPLS circuit on primary router (CISCO 2951) and 1 x 8 Mbps Ethernet link on secondary router (Cisco 2951). We have successfully implement the primary router with 2 x 4 Mbps MPLS circuit. Site is having two computer room CR1 and CR2 and distance between both room is 200mts. CR1 is having primary core router and primary core switch where the service provider terminated the new MPLS circuit and we have done the successful implementation. CR2 is having Secondary core router and secondary core switch where we needs to have the termination of Ethernet link but service provider has delivered the Ethernet link on the CR1 which is incorrect DMARC Location.
Both the computer rooms are connected via optical copper can we use that copper to connect the circuit on CR2, as per my understanding we can use the optical fiber to connect the wind circuit on secondary router on CR2 by using the media connector.
So I have installed my new E4200 version 1 and I am disappointed with the speeds. My computer has a wireless N card and gigabit Ethernet compatibility. I am currently getting a miserly 54 mbs wireless and 100 mbs on the wire (connected with cat6 all the way)... Anything I should try to get close to advertized speeds?
View 9 Replies View RelatedIn other words. If my cable modem only has 50 mbps is that all I will get out of my wireless router, even if the router has a higher mbps rating/
View 8 Replies View RelatedWhich is the wireless speed of this router? No speed infos are present in the official web site. In the web some sites say it's a 300, others say it's a 150, others 248...
View 9 Replies View RelatedI was wondering why the heck I'm getting BELOW 1 mbps toward my internet connection? I look at my wireless signal, and it's full. yet, I go on speedtest and have about 0.20 mbps.
Info - My parents pay nearly $100 for this bundle thing with the internet, phone, and something else, I think TV.
provider - windstream
router - F@ST 1704
Also, the router is currently on top of the main computer in the office, on top of the router is a house phone.Yet, if I move the house phone, nothing changes. The computer is on the floor.Should i move it? Would this improve my connection?Even the main computer that's wired with the router gets the same mpbs as wireless.
I have a desktop and laptop here, the desktop being mine custom built wireless and all, and my buddies desktop.The issue that I'm having is that my desktop, regardless of wired or wireless gets 25 mbps down speed, and the laptop gets only 2.5 mbps down speed wired or wireless
View 4 Replies View RelatedI have a problem with my home network (diagram attached below). I sporadically lose connection between my Router and the devices behind the switch. I have replaced the Ethernet cable between the 2 so I don't think the problem's there. It will work for a week or so, then just lose the connection. I then try a combination of rebooting all of the devices on the network and/or unplugging and re-plugging the cable connections and sometimes that works. It's a relatively new router, but can a router be "underpowered" for pushing a signa
View 2 Replies View RelatedThere is a device which is connected to the PC via Lan. I have an exe file which is supposed to get connected to that device and perform some operations. However, the problem is, the exe file tries to connect to the local host ip address 127.0.0.1 and i cant change the ip since it's been coded.So, I'm wondering if i can use the device connection (which already has a different ip like 169....) as a local host connection. So whenever it tries to connect to the loopback 127... it automatically connects to the external device.
View 2 Replies View RelatedI'm using an HP G60 laptop, running Win 7 Pro x64 SP1, fully patched. I'm usually in the home office, connected to a D-Link DIR-615 router (h/w: E3, f/w: 5.10, the latest). The internal Atheros AR9285 N150 wireless adapter has never been as reliable as I'd like, so decided to purchase a USB N300 adapter. I bought a TP-Link model for $10 and started using it. For some reason, it would only connect at 150, unless I ran the router's Web interface and saved the wireless settings, even without a change, at which point I'd see 300 Mbps. However, at the next restart after hibernation, the connection with the DIR-615 would fall back to 150.
I stepped on the TP-Link USB adapter and broke it. Oops. Decided to purchase a D-Link DWA-131 (h/w: A1, f/w: 1.21, the latest) 'cause it's compact and the box says that, "For Optimal Wireless Performance +Use With Wireless N 300 Router (DIR-615)."Expected 300 Mbps, but it connected at 65. Argh. Did the trick again with the DIR-615's Web interface, and saw 150. But after restart from hibernation, back down to 65. Unable to achieve 300 Mbps, unlike the cheap-o TP-Link adapter. Router is configured according to Lycan's sticky note. Router's Wireless Status shows a signal of 39%, and the router is in the next room in a wood-framed building.Is this as good as it can be? Looks like the DWA-131 is coupla years old with no new drivers for Win 7. Ran the DSL Reports Java speed test, and seeing 18+ Mbps d/l, and 1.8 Mbps u/l, which is about average from Cox here in The OC. If I can't get a faster connection, then D-Link's claim of "optimal performance" is misleading.
I have 1 mbps internet connection and I got two computers to be connected. optimum configuration of the router required.
View 5 Replies View RelatedI have a Linksys e2000 wireless router, my laptop connects fine, but as i keep hovering my mouse over the wireless icon in my system tray, it keeps changing Mbps from 130 at its highest going down into double digit Mbps, then back up to 130. Why wouldn't it stay connected at 130 all the time?Someone said to try lowering the beacon interval, fragmentation threshold, RTS threshold, and mtu size, but will doing that decrease the speed of my connection to the router?
View 5 Replies View RelatedI know that this Router of D-Link DIR-655 can't handle 450 Mbps Wireless Connection.
What is the newest D-Link Router available that can handle 450 Mbps Wireless Connection? Does the Network Wireless Adapters need to be change to achieve this?
TRENDnet 450 Mbps Wireless N Gigabit Router TEW-691GR (Piano Black)
[URL]
Newbie network admin here and I'm having problem dealing with my LAN. I have two networks 192.x.x.x and 10.x.x.x, Configured at my Astaro 220 UTM, which obviously where the gateway is, from my UTM I have 3 isp connected which is the source for my internet. Now from astaro to my core there are two connection, 1 for the 192 network and the other is for the 10 network and from the core there goes my LAN where switches are cascaded.My problem is i'm having slow connection accessing from 10.x.x.x to 192.x.x.x network vice versa. what are the possible solutions is applicable, or the things I should check. plus I can't access(configure) my switches which is on the 192 network from 10.x.x.x. network through web.
View 1 Replies View Relatedi have Cisco 3845 with 1 GB SFP, my company using fiber as backbone to isp, i have new internet connection 310 Mbps, does that enough ? does that for port only for LAN or also for WAN ?
View 8 Replies View RelatedI have 100 Mbps Half Duplex on one side of the Switch. ( Autonegotiation disabled )I have 10 Mbps Full Duplex on the other side ( Auto-negotiation disabled ). Should the link come up on both sides
View 4 Replies View RelatedI need to apply DHCP snooping on 4500 series switches working as L2 in my Network. We have external DHCL Server in another location connected with 6500 series switch.
Running EIGRP Configured Voice & Data Vlan both
DHCP Server -------- 6509 switch<----------------------------------->6509 Switch -------- 4500 switch ----------------------------------------------------------Ip Phones.
(ving Redundant) (ving Redundant)
I need to know whether the configuration which I mentioned in scenario is enough for apply DHCP snooping in my network.
Is it possible to connect two distant sites e.g. 30 miles wirelessly? Will there be any issues with Line of sight and interference? Will it be a better solution compared to that of wired counterpart?
View 3 Replies View RelatedI have a PC that connects to a wireless connection. I would like to share this connection with MORE THAN ONE PC. I have read it is possible to share it with ONE other PC via a crossover cable.I would like to share this to a router so that the PCs connected to the router can use this connection. Is this possible?If so, what would I need?(Other than a crossover cable and router)Side note: I'll be sharing this connection to a wireless router - so I'm hoping to basically relay the connection that way.I know it is possible to buy extenders that extend the range of wireless connections, but this is where the restrictions come into play...-We are not able to network these computers on the wireless network, as we do not manage it and have some quite strict privileges.-The router will also be used to share a hard drive via USB.
View 2 Replies View Relatedi have a wireless adapter connected to a different wireless network. now the issues is i have my own router which i want use for my ps3 and phone to access my files from my pc but every time i connect my router, it switches from my wireless to LAN by default hence no internet connection.i want to be able to use my wireless connection for internet
View 1 Replies View RelatedI have connected my Vista laptop to my old XP laptop using a network cable so that I can share files, printers, etc freely.I have forgotten the correct proceedure for doing this, although the two computers eventually, after a long time link up and I am able to share files. I have done nothing else. I have not entered numbers or anything. The number spaces are blank.I do not understand why it is working at all, but how do I speed up the connection?
View 14 Replies View RelatedI have a Linksys e3200 which was working great until about a week ago. Now any device that connects via DHCP does not have access to the internet, though devices set up with a static IP outside the DHCP range still have full access.The devices connecting via DHCP still have full network access, just not internet access.I tried most of the obvious fixes (reboot, changing the range and lease time for the DHCP) but have at best received a temporary fix.
View 1 Replies View RelatedI have a Linksys/Cisco wireless router. For the purposes of a high def throughput, I have a wired connection from the router to a Windows Media Center appliance in a separate room.However, now I have a second media appliance (Roku device) that I want to run in a wired fashion as well. Here is the thing, I don't want to run a second Ethernet line from the router to new roku device. Is there some way I can share the existing ethernet line between the roku device and the media center appliance? Ideally, since the two devices would never be used at the same time, I was hoping some other network device (another router?) could be hooked up to split the line between the devices. Worst case, is there some simple splitter I can use? Obviously I am trying to avoid the worst case scenario: switching the ethernet connection manually between the two devices every time I want to go from one to the other.
View 6 Replies View RelatedI have a Rosewill RNX N300X wireless adapter that keeps dropping to 1 mbps, and only goes up to about 18 mbps on a good day. How can I force a 54 mbps connection?
- I am running the latest drivers for the card.
- The network is "g", card accepts b/g/n.
- Another computer running RNX N360PC is getting a perfect connection on the same network.
I have a Router 877 and a switch 3750 also a 10 mbps internet connection and I want to share the internet connection to 5 different vlans with a maximum of 2mbps each one or 2 mbps guaranteed. The switch and the router are connected for a trunk port and the vlans are defined in both devices. I have tried many configurations of this with no success.
View 4 Replies View RelatedI'm sure this may appear to have been asked before but I've scoured the Internet and can't find anything exactly applicable to the setup I'm trying to achieve. I had a sky ADSL connection in my living room that had my tv, ps3, NAS and netbook wired in. I've since changed to a sky fibre connection but this had to be installed in the master phone line which is upstairs. This obviously isn't a problem for all of the wireless devices around the house including the netbook and ps3 in the living room. The NAS and TV are still wired to the old router so can see each other with no problems. Any pc trying to connect to the NAS can just switch to the old router via wifi if desired. The only problem I have is that the TV can no longer access the Internet.
I initially tried to use ICS on the netbook (it's left on permanently) - it's wired to the old router and wirelessly connected to the new one. This appeared to be working for a while but is no longer playing ball. I've tried bridging the connections and the tv and NAS both had Internet access but it's very sporadic.Is this a reasonable setup or should I be looking for another solution? I can specify a manual ip, subnet and default gateway on the tv if necessary - I was going to point it towards the bridge's gateway but I don't know about IP?
I started having this stupid problem after i built my first computer, in my old computer it was all fine, am using an ethernet cable between my pc and laptop, it is crossed or whatever its called, when i plug it in it gievs me an error, limited connection or no connectivity which pisses me off, i have all the drivers installed everything is up to date.. sometimes it connects, but after 10 mins it disconnects again, and sometimes it works fine until i reboot my pc..
View 17 Replies View Relatedi have triple storey house. in all three floors a broadband connection point (rj45 jack) is there. i have connected one wireless router in 3rd floor. but the signals are not coming on second floor. can i connect netgear wireless access point with one ethernet point in the 2nd floor broadband connection jack (Rj 45), to access wirelessly my internet?
View 1 Replies View Related