Linksys Wireless Router :: Cannot Reach To 450 Mbps With EA4500
Feb 8, 2013
I have a new EA4500 router and I cannot configure it to reach the 450 mbps that is supposed to get.
I have it configured as follows:
Dual Band- 2,4 and 5 GHz
2,4 in 20MHz only - 5 GHz in 40 MHz only
2,4 Mixed - 5 Ghz only N
WPA2 personal in both
Channel - automatic (both)
I have checked that the 5 Ghz network can only use 4 channels: 36, 40, 44, 48. Where are the channels up to 100 (or more)? How to get all the power of the router?
View 2 Replies
ADVERTISEMENT
Jan 20, 2011
I have a laptop with an Intel Centrino 6300 Ultimate-N wireless card. With the previous firmware I was able to reach 300mbps while on the 5GHz band. Since I updated my E3000 to the latest firmware (1.0.04) I can only reach speeds of 144mbps. I have done a factory reset on the router and stll get the same result. Is there any way I can get it to reach 300mbps again with the current firmware?
Also, yes I have uninstalled / updated the driver software for my wireless card. I have also changed the appropriate settings for the 5GHz band. (40MHz channel width, using WPA2 encryption)
View 9 Replies
View Related
Feb 5, 2013
I am only getting 10-14 mbps when I should be getting 30-35 (using the gigabit ports). I thought it might be my provider but today I connected my old netgear router and the speed was 32-34 mbps. Is there some setting that I should be looking at?
View 5 Replies
View Related
Feb 24, 2013
We have a large house, with wired connections in every room. After the ISP just installed a new EA4500, the wireless signal does not reach the whole house.Is it possible to plugin the old X3000 into the wired connection upstairs and have it boost a wireless signal to that area?I know how to reset the unit and access the setup page.
View 2 Replies
View Related
Mar 11, 2013
I just ran some speedtests om my PC on the advice of my isp to see if my Linksys WRT54G router might be bad. As a result, I found that the router might not be entirely bad, but it might not be entirely good, either. I got .77 Mbps dowload and .17 Mbps upload on the first speedtest. I got .43 Mbps download on the second speedtest and the speed test hung hear the end. When I connected an IMac to the cable modem with an ethernet cable, the IMac ran strong. So the tech thought I should get a new router.
But wait a minute, isn't there a network adapter in the PC that the router talks to? Might the adapter be the problem, not the router? So I speedtested the wireless network to the IMac. That speedtest was fine, tiptop, like the ethernet direct connection test noted above. Did that tell me that the problem is in my PC network adapter, not the router? Then, I retested (speedtested) the connection on the PC and it was fine...excellent. Good up and down speeds, no hangs.Then, I checked the PC adapter (a Belkin). I saw three adapters on Device Manager, including the Belkin. I downloaded new drivers for the adapters (except for the Microsoft Virtual WiFi Minipoty Adapter - because it got a warning that the download software wasn't signed and might harm my computer).
View 9 Replies
View Related
Dec 22, 2011
So I have installed my new E4200 version 1 and I am disappointed with the speeds. My computer has a wireless N card and gigabit Ethernet compatibility. I am currently getting a miserly 54 mbs wireless and 100 mbs on the wire (connected with cat6 all the way)... Anything I should try to get close to advertized speeds?
View 9 Replies
View Related
Mar 15, 2013
Which is the wireless speed of this router? No speed infos are present in the official web site. In the web some sites say it's a 300, others say it's a 150, others 248...
View 9 Replies
View Related
Jul 24, 2012
Contrary to what i have been reading, i have a DOCis 3 Modem, on Comcast, with an internet connection of 1GB. My wireless connections are in the 150-300 Mbps range thru a Linksys 4500N router
View 1 Replies
View Related
Jun 21, 2011
after messing with it for a 2 days since I got it I cant seem to get more than 130.0 my last router had 300 same setup same distance
View 9 Replies
View Related
Dec 28, 2011
I bought a Linksy E4200 yesterday and set it up fine, but I only seem to be able to get 130 Mbps on my Wi-Fi. I looked through these threads and tried disabling the 2.4Ghz band and it still remains at 130Mbps. There was no change, also read I can try set up a secondary SSID. I really don't know much about routers or configuring them
View 4 Replies
View Related
Mar 16, 2011
I currently own a LinkSys-WRT54GL 802.11a/b/g wireless router, and my ISP is Comcast Cable providing me with 15 Mbps (that's bits per second, I believe) download speed. I am wondering if there is any benefit with using an 802.11n wireless router to access the Internet? The maximum theoretical speed of the WRT54GL router is 54 Mbps (802.11g), which is faster than the 15 Mbps provided by my ISP.
I know that 802.11n has a max bandwidth of 300 Mbps, and it would work for intra- house transfers, such as streaming video from one computer to another.
But is there any benefit to 802.11n for Internet activity, such as web browsing, gaming, and streaming video from Netflix.
View 3 Replies
View Related
Mar 1, 2012
In other words. If my cable modem only has 50 mbps is that all I will get out of my wireless router, even if the router has a higher mbps rating/
View 8 Replies
View Related
Jul 3, 2011
I have DSL set up in a home network. I want it to be used in my barn. The signal won't reach wireless though. I have 2 older wireless routers not being used - Lynksys wrt54gx4. Can I add two of these in the path to the barn to extend the signal? I would put one in the back of the house and one halfway to the barn in the pool house. ZCan these routers connect wirelessly to the home network?
View 3 Replies
View Related
May 15, 2012
I am trying to access [URL] with a Linksys E3000 router. A few days ago it was working fine, and between then and now I made no changes to my network, it just stopped working one day, I assumed the website was down but it turns out that I am able to access the website fine on other networks or via proxies. I also hooked up my computer directly to my modem and I was able to connect to the website fine, but when I try my wired connection to the router I am unable to connect, I have tried Google DNS without success. I know this is a problem with my router, not my modem or computer or ISP.
View 9 Replies
View Related
Mar 25, 2013
it might be good to point out first that this was never a problem before i began fixing a completely irrelevant problem (screen broke) with my laptop, which took around three weeks. i could at that time use the internet a couple of rooms away from the router just fine, but now it's a no-go. .
the model is WRT54G, and the serial number is CDFD1F9CJ507.
View 1 Replies
View Related
Jul 13, 2011
Why my internet was so slow .90mbps. They got on my mac and changed the Ethernet setting to "manually" instead of "Automatic", then changed the speed to 10mbps instead of "autoselect". Now the internet is going at the 10mbps im supposed to be getting, but when i plug it into my router (wall>router>laptop) i get the .90mbps again. So do i how do i change the same setting on the router?
View 1 Replies
View Related
May 25, 2011
I have the WRT160N. Using [URL], I can get 2.5Mps from wired ports, but less than 0.5 Mps using the wireless.
View 9 Replies
View Related
Jun 29, 2011
I have Wrt610n V1 Firmware V 1.00.03 B15 and internet 300 mb.If i connect PC to my internet bridge i have 300 mb. But when I switch between a WRT610n all ports have ~100mb. In router I removes all check marks from all security, filter.
View 6 Replies
View Related
Apr 29, 2013
When I connect my modem directly to my computer I'm getting 27 MBPS speed. When I hook it up through my router, speed slows to 15 mbps.
View 2 Replies
View Related
Aug 3, 2012
My new (30 days old) EA2700 has probably less than 40 feet of usable range without obstructions. Is this normal?
I've got the router sitting at the end of the hall, and I'm at the other end without anything between and I'm at 11.0 Mbps/'Low' on my laptop.
View 9 Replies
View Related
Dec 30, 2011
I posted this in the wired forum, because it's the wired speed that is limited, but it looks like there's more E4200 expertise over here, so here it is again:
I have Hotwire fiber service and the plan is supposed to provide 20 megabit downlink speeds.
I just bought a Linksys/Cisco E4200 to replace an old Dell TrueMobile 2300 from 2004. With that router I got the full advertised downlink speed.
Now, when I run a speed test with the E4200 in place, the downlink speed is only 5168 kbps or so. Watching the speed test meters, I see the data arriving in bursts, every few seconds a whole lot of it gets through, then for a second or two nothing. It's pretty regular.
But, if I run a speed test with the ONT cable plugged right into a laptop, I see 19001 kbps - close enough to 20. This is the same cable that plugs into the back of the router.
With E4200 in place Direct into laptop what I can check or configure in the E4200 to change this behavior?
View 4 Replies
View Related
Aug 11, 2011
I purchased a new router - cisco e1000. Currently, i have 2 laptops wirelessly connected to this router. When i do a broadband speed test, the speed drops down significantly to 8MBPS while if i connect it to the cable modem directly (wired) i.e., without router, i'm getting 15 MBPS download speed. I did a couple of times this speed check and the results are same. I tried changing the advanced settings in the router (which was specified in one of the post in this forum) but no luck. Is it that i need to buy e4200 to match the wired speed of 15 MBPS or what other things I can do to get the same speed of my cable modem (provided by my ISP)?
View 1 Replies
View Related
Nov 5, 2012
I'm running a Cisco E4200V2 router with the latest firmware (2.1.4.12284) on an iMac running OS X 10.8. My ISP is providing 15Mbps to my modem, which I've confirmed by connecting directly to it without the router. Once I put the router back in the path, my broadband speed drops to about 6 Mbps. Is this the best I can expect from this router?
View 2 Replies
View Related
Dec 8, 2012
I've had this router for about 3 weeks. It's only 20 feet from the computer, but my computer on 2 or 3 separate days had trouble staying connected. The signal dropped to 5 Mbps and had a little yellow symbol that said no internet access and when I looked at the properties it said, "limited or no connectivity." I got impatient and purchased a 75 ft Ethernet cable online with plans to possibly return the router as I don't really need wireless anyways and since I spent $100 on this router I expect it to work at 20 ft distance.
For the last few days it has remained at 54 Mbps or more sometimes all the way up to 108 mbps. But now since it got pretty low a few times I don't trust it enough so I might return it anyways.IPv6 connectivity says no network access. This might be because when it asked for administrator password to recognize it as a trusted home network I closed it instead of putting in the password.
View 5 Replies
View Related
Oct 9, 2012
I just "upgraded" from an E1000 to an E1200 wireless router. I had good performance with the E1000, and I only upgraded to the E1200 because it was on sale.My only complaint with the E1200 is the slower download speed on my desktop PC that is connected directly to the router. My normal download speed on the desktop PC was 25 Mbps with the E1000 model. After I disabled the WMM on the E1200 as others suggested, the download speed on the desktop machine immediately increased from 5 Mbps up to 15 Mbps. Any other suggestions to get the download speed up to 25 Mbps before I switch back to my E1000? The E1200 router is connected to my Arris TM602G modem. Both modem and router were reset during the installation process. I setup parental controls for a couple of iPods and configured Open DNS, but other than that, the router is using default settings. All wireless devices in the house seem to be performing fine with the E1200.
View 8 Replies
View Related
Aug 16, 2012
I've recently subscribed to a 100Mbps fibre broadband service with the bundled Huawei EchoLife HG8240 ONT modem and speed-tested it with an achievable speed of almost 100Mbps (uplink and downlink) on my desktop PC.However, when I connect my new Cisco Linksys E1200 Wireless-N Router to it, I noticed the speed dropped by almost half (about 50Mbps both ways) when I conduct a similar speedtest .
note that I'm using wired cable and there's only 1 single PC connected to it and it is not shared. This includes upgrading the firmware to the latest version, disabling the IPV6 setting and configuring QOS.My current hardware/ firmware version is as follows:
H/w ver : 2
F/w ver : 2.0.03
View 2 Replies
View Related
Sep 13, 2011
I just bought a refurbished E2000 wireless-n router with 1 Gb LAN ports (from Cisco online).This router is meant to replace my Netgear wireless-n router that only have 100 Mb LAN ports.I have 10 devices in my home network, 6 of them are using wireless (1 'g' and 5 'n') and 4 are interconnected with cat5e cables (trough the router).The devices have some different operating systems and their network adapters are from different brands.When I set up the Netgear router I didn't have to adjust anything for the wireless network to work fine.All wireless-n devices worked at 150 Mbps (sometimes going down shortly to 130 Mbps).The wireless-g device worked at 54 Mbps.For the last 2 days I've been trying to set up the E2000 to achieve a wireless-n speed higher then 72 Mpbs... without success.I tried all the suggestions that I found in the Cisco Knowledge Base.
- Upgrading the firmware to the latest version
- Trying different channels and channel widths
- Different wireless security methods and many others.
Also trying different settings on the different devices doesn't work.Changing the distance between router and devices as well as changing the location of the router don't affect the results.Switching on only 1 device at a time doesn't change anything either.It looks like the E2000 is set to not transmit on a higher speed than 72 Mbps, when it's actually supposed to achieve a wireless-n speed of up to 300 Mbps. I would be lucky if I get the half of it, but not if it's only one fourth.
View 3 Replies
View Related
Jan 8, 2013
I have a desktop and laptop here, the desktop being mine custom built wireless and all, and my buddies desktop.The issue that I'm having is that my desktop, regardless of wired or wireless gets 25 mbps down speed, and the laptop gets only 2.5 mbps down speed wired or wireless
View 4 Replies
View Related
Feb 25, 2012
Goal: extend the reach of my WiFi to multiple floors with keeping in the basement the DSL modem - Actiontech M1000 and Actiontech W1000. I have a Linksys Access Point and Linksys Router. I was told by CenturyLink (only allowed support for Actiontech) that the modem would need to be put in bridge mod that would disable the Actiontech W1000. Whereas I want to keep access in the basement and add coverage to upstairs.
being able to config the Linksys(s) or using DD-WRT operating system?
View -1 Replies
View Related
Sep 2, 2012
I've looked all over the internet for this and can't find a definate answer. Waited for live chat and got kicked before I got to talk to someone... Just sold my computer and the plan was to buy a newer mac but we've been getting along fine without a computer with just using our iphones. So my question, I see that Cisco has the Connect Express app for the iphone, and I've read about all the features it has like changing settings, router features, etc. But I can't find anything on using the app for the initial set up of the router. I'm currently on an older linksys router (set up before we sold the computer) but it's time for a needed upgrade.
View 3 Replies
View Related
Apr 30, 2012
I got my ea4500 all set up. never had a media servor or anything like that, figured this would be an easier way. when i hook up my exteral i can find it but i can only view the files in windows media player. how can i just browse the folders manually? WMP doesnt let me browse the folders as they actually are on the HDD which is such a pain in the **bleep**.
shows a device in "network infrastructure" but it says problem sending command to the program when i click that. i dont want to have to view the HDD in WMP as a media device...
View 1 Replies
View Related
May 12, 2012
My new EA4500 (fw ver 2.0.36) won't obtain an IP from a Brighthouse TM502G cable modem. The EA4500 replaced a functioning WRT54G which would obtain an IP from the ISP. I've tried upgrading firmware and have used both straight-through and crossover cables between the EA4500 & TM502G to no avail. The EA4500 would issue IPs to it's clients, but not obtain one from it's TM502G. At the moment, all 3 are daisy-chained together with the old WRT54G in the middle in order to make the EA4500 work. Both WiFi and LAN ports function in this configuration.
View 1 Replies
View Related
Dec 19, 2012
I downloaded and installed inSSider for Windows and, under the 2.4 Ghz tab, I can clearly see the Router SSID, on Channel 6, exactly as configuredbin the Router. However on the 5 Ghz tab, nothing? I can see Channels 36, 40, 44, 48, 52 and so on BUT no trace of any wireless signal here?I carefully reviewed the wireless settings options and it is indeed enabled.
View 1 Replies
View Related
