Linksys Wireless Router :: E4200 - 2.4ghz Network All Connections
Sep 1, 2011
I purchased a e4200 in hopes that its dual band capability would allow us to run a 2.4ghz network for certain devices and a 5ghz for everyone else. I am able to setup the router and connect but it seems when the 2.4ghz network drops the router drops all connections.
At first I had the networks setup with the same ssid, then changed the 5ghz network to a new ssid but was still losing connection when the 2.4ghz network dropped. This may be a simple routing issue i am overlooking (bit of a network newbie).
View 3 Replies
ADVERTISEMENT
Oct 15, 2011
2 days ago my e1000 died, so I went big and bought the e4200 (due to newness, its already loaded with Firmware 1.0.03 build 14) to aleviate my networking woes. I'm running into an issue where I'm utilizing both the 2.4Ghz bands and the 5Ghz band. My desktop as an AE1000, and I'm utilizing that on the 5Ghz band. Everything else in the house (Dell laptop, 2x iPhone 4 and an HP printer) are all connecting to the network wirelessly.
I have had 0 network issues with regards to my wired connections, or my 5Ghz connection. But my 2.4Ghz connection will continuously be unavailable. I have both bands set to brodcast, they have different names so my AE1000 can connect via 5Ghz band. Both yesterday evening, and this morning, my phones, laptop and printer cannot connect, and for the most part, the network doesn't show up on available networks. When it does show up, the devices can't connect.I'm proficient enough to do the general home networking, but I'm at a loss as to how to fix this, without a daily reboot of the router (which seems excessive and unwarranted for a 2 day old e4200 [or any router to be honest]).
View 2 Replies
View Related
Oct 27, 2011
On my new E4200, I cannot connect wirelessly to the 2.4GHZ band. I can only connect to the 5GHZ band. I know its not the distance because i've got my laptop only 2 feet away. I've hit the refresh wireless network button, but the only network visible is my 5GHZ. I've also restarted the router, no luck
I went into the router settings and made sure that BOTH SSID'S are broadcasting a signal.and are enabled (ive got the channel and other settings set to auto). I'm able to connect perfectly well to the 5GH band, and walk around the house, but nothing i've done, allows me to see the 2.4GHZ band? So far, my wireless reception is poorer than my old wrt310n.
View 4 Replies
View Related
Jun 19, 2011
I installed an E4200 in an outdoor patio area where the ambient temperature can be high (Las Vegas area); however, the router is located in the shade without any direct exposure to the sun. After using the router for about 15 minutes, the router is extremely hot and 2.4GHz band will stop working. In addition, even when the router is working, the 5 GHz band connects at much higher speed than the 2.4 Ghz band. The internet download speed is much higher using 5 GHz compared to 2.4 Ghz.
View 9 Replies
View Related
Jul 11, 2011
Both use the same encryption (WPA2-Personal), same channel and they are tested in the same location with g-only mode. Only one router is switched on at any one time during the test. When 3 g-client notebooks (of various brands) are associated with the E4200, the signal indicator is a single bar, wherelse they can get 3 bars with the WRT54G (in the same location). For Internet speed test on a 20Mbps link, WRT54G is able to substain about 10Mbps, but only 1-2Mbps with the E4200.
Is such difference in performance between the two router models normal? Is there any configuration required to tweak the E4200? Or is it a hardware related issue with E4200?
The E4200 has been updated with the latest available firmware as of yesterday.
View 2 Replies
View Related
May 31, 2011
Using firmware 1.0.01, has anyone successfully gotten the E4200 to bond two channels using the 2.4GHz spectrum? I just can't get it to bond. I assume it's a firmware issue, yet to be fixed. I've tried settings Auto (20 or 40), and nada. It has never bonded. The 5 GHz bonds fine. There are a few interferences by the neighbours wifi, but nothing substantial that should prevent bonding. I have this router at school too, and the same thing happens there, with the same firmware, so I doubt it's an interference issue. I'm using WPA2 Personal encryption. I tried auto channel, and setting channels to 1, 3, 5, and 11, nothing changed.
I know I'm not bonded because A. Max link speed is ~144Mbps, and B. using a program like inSSIDer tells me I'm only using one channel on the 2.4Ghz spec.
View 8 Replies
View Related
Aug 21, 2011
I have a E4200 updated to the latest firmware I have problems with the wifi on the 2.4GHz band, in fact, at power on, many times wi-fi on the 2.4GHz band doesn't work but the 5GHz band works normally. After some reboots the wi-fi operating normally on both bands.
View 9 Replies
View Related
Mar 16, 2011
my e4200 updated with latest 1.00.1 firmware is constantly dropping connections from the outside to existant lan servers running low traffic services when my machine is using torrent or internet gaming.( call of duty modern warfare )
View 9 Replies
View Related
Apr 11, 2011
my E4200 is dropping connections several times a day. I'd be working on my laptop, go to a webpage and bang, no connection. A minute or so later it would reconnect. It even appears to be doing this with a computer that is hardwired to one of the ports. So it doesn't seem limited to just wireless. Happens to both N and g channels as well.
View 9 Replies
View Related
Sep 5, 2011
My E4200 seems to be dropping connections throughout the day. For wireless it'll still show full signal and connection, but there will be no internet activity for about a minute. Then after a minute things will work just fine again. For wired I notice it in my XBox mainly when I get dropped from games as constant as the wireless drops.I believe my modem isn't the problem since the old router never dropped connections on the hard wired devices. Occasionally my old D-Link router would drop wireless, but never this frequent,I am running 1.0.02. I've rebooted the router/modem several times. I even reinstalled the entire setup with the current version of Cisco Connect as the tech person suggested, but still no luck. The first week or so using this router was flawless, but ever since then it's been dropping connections several times throughout the day to any device connected (wireless or wired). The problem seems that the router just hiccups the connection very quickly, so quickly that Windows doesn't even recognize the connection has been lost, but long enough to drop a multiplayer game on XBox or to have me mashing refresh on my internet browsers.
View 2 Replies
View Related
Jul 14, 2011
I'm trying to fix the network at a student housing building and the system is kind of a mess. We bought a new E4200 to replace our old Linksys router which no one knows the admin pw to. We have four switches for 50 connections throughout the four story house and when switching the connections over to the new E4200 all of the wired connections no longer work. Switch back to the old router and presto. How do I need to change the settings with the E4200 to get it to work?
Also, as it's a thick old house the E4200's wireless only covers maybe half of it...I purchased two wireless repeaters to put on the 3rd and 4th floors, are these simple to install with the router?
View 4 Replies
View Related
Jul 31, 2012
My router was working just fine forever, the only computer that will connect VIA wire is my desktop, everything else for it to connect to my network it has to go wireless. Things like my blu ray player just will not connect. I am not an expert at all, but why is only the wireless working? I can use the Cisco connect and adjust the settings if need be.
View 5 Replies
View Related
Apr 3, 2013
I purchased a EA4500 and at first I could connect to it through its default ciscoxxxxx ssid on my laptop which is 2.4GHz only. I upgraded the firmware using the PC utility and now I can't find the 2.4GHz SSID no matter what settings I do. I've disabled and enabled it multiple times, changed it to have no security or with security and enabled and disabled it and renabled it. Nothing seems to work, but for some reason the 5GHz side I can connect to using a 5GHz device. I've also tried disabling the 5GHz side, but still no 2.4GHz.
View 4 Replies
View Related
Dec 23, 2011
Decided to go with the e4200v2. 199.99 for a router 450 + 450 with a little extra features. very pricey but thought it would be worth it. I got it hooked up with no problems for the first 5 minutes. I have 35mbps down wired from the router and on the 2.4 and 5.0 ghz band about 25 feet from the router was getting just that!! no loss really. However after a few more speed test i noticed it was fluctuating very slow to fast. Also the 2.4ghz was only 144mbps. after getting in the router i changed the 2.4ghz to channel 6 and 5ghz to 153 and changed to 20mhz only on the 2.4 and 40mhz only on the 5.0ghz. Now all is doing well .
1. why am i not able to run the 2.4ghz on 40mhz? when set to auto i have a lot slower speed tests even know it is running on 20mhz only because I'm only getting 144mbps. I don't know why its not running 40mhz ? i don't know why i have to change it to 20mhz only why cant i leave it on auto and if i had a day with little interference it would switch to 40? when left on auto the speeds go down drastically
2. i notice that some channels are brutally slow on both bands. like 1.5mbps ? is this normal
3. is this even worth it if the 2.4 band is acting this way?
4. from insider i see that 5.0ghz only connects to two channels isn't suppose to be 3?
View 4 Replies
View Related
Jul 3, 2012
My 2.4 GHz is not working corrently on my EA3500 router. I have no trouble with my 5 GHz which I am currently on. On my iPhone I have to manually click the network even though it is known and then the wifi icon lights up full then goes dim then just flashes til it gives up. If I try connecting with my computer it just doesn't load the internet.
View 4 Replies
View Related
Feb 23, 2013
On my dual band E2500, I have both the 2.4 and 5 GHZ enabled. I have a fairly new HP with an N wireless card but I cannot get it to connect at the 5GHZ frequency. The only computer that will connect at the speed is my wife's with an external Cisco wireless card. What the settings should be on the PC in order to get it to connect at the higher frequency?
View 4 Replies
View Related
Mar 19, 2011
How do I know if I'm using 2.4 or 5ghz? I would like the laptop and ps3/net flix to use the 5ghz and everything else to use 2.4ghz. I used the e3000 CD fro the setup. When I was at the last part of the setup, when it gives you a ssid name and password. I deleted it and typed in a name that I could remember. I clicked the button for the next step and everything was complete. I also received another name for guest to use the computer. The e3000 setup just game me some wild name like running water.
I would like to know since I have two different names, which on e is using 5ghz and which one is using 2.4thz? Can you tell me if the e3000 automatically have the first name use 5ghz and the guest just 2.4ghz on the second name?
View 3 Replies
View Related
Jul 24, 2011
I just recently (4 days ago) purchased an E3200 router. I noticed some random disconnects on my devices using the 2.4GHz frequency.I installed inSSIDer from MetaGeek to see what was going on and noticed some strange behavior where the Amplitude on the 2.4GHz randomly drops dramatically. Sometimes its once every 10 minutes, other times it happens 5 times in one minute. I can't figure out what is the cause. The 5GHz signal is steady as a rock.
What I tried so far: Set the Channel to the least crowded channel instead of auto, upgraded the firmware, restarted the router all to no avail. This is annoying to say the least. It doesn't affect anything unless you are playing video games or running a remote desktop session, where a single disconnect is disastrous. I just upgraded from an old linksys wrt54g, tried a netgear n600 which was terrible, then swapped it out for the Cisco E3200..
View 7 Replies
View Related
Oct 11, 2012
My E4200 router no longer accepts any WIRED connections. I can connect from the modem to the computer and everything works as expected. I can connect other computers wirelessly to the router. I cannot connect any laptops WIRED to the router. Nothing has changed on the systems to restrict internet access. There is something wrong with the router and the WIRED ports. I tried going through the troubleshooting on this site but it was of little to no assistance. The Cisco Connect utility doesn't appear to accomplish anything either. My guess is because I cannot connect to the WIRED ports on the router to connect to the internet to allow for whatever troubleshooting that needs to be done.
View 2 Replies
View Related
Dec 18, 2011
having wireless G network coexist with Wireless N network on e4200.
I have an existing wireless G network with ActionTec router for VERIZON FIOS. I just added the E4200 router for wireless N. I have latest firmware, 1.0.03. Version 1 hardware.
We are getting a couple of laptops for holidays and would like these to be able use wireless N. I have older laptop/itouch/roku device that use wireless G/B network from ActionTec router. I would like to keep the ActionTec router for wireless G/B, so that both 2.4 and 5.0 ghz networks are Wireless N only.
I have both routers configured so that ActionTec is primary with DHCP and the e4200 is secondary, setup in bridge mode, with DHCP off and static ip of 192.168.1.2. Used this for guidance -> [URL]
I have one SID for ActionTec Wireless G network and this is set for Channel 1
I have a different SID for e4200 Wireless N network, same for 2.4 and 5.0 and I left defaults on other wireless settings.
View 5 Replies
View Related
Feb 21, 2013
I have the wireless guest network up and running just fine. But, I need to also connect to the router's quest network via one of the ethernet ports. Can I just give the LAN-conencted PC a 192.168.3.x static IP to access the guest network? I am assuming there is no VLAN functionality...
And even better, can I set up a DHCP relationship to that port? So that any device plugged into the port will get a IP on that subnet?
View 4 Replies
View Related
Aug 21, 2011
I have e4200 router set up with different SSIDs for 2.4ghz and 5ghz. My laptop (Lenovo x220 with Intel 6205 wireless adapter) can't see the 5ghz network. I've tried changing the channel for the 5ghz network and it didn't fix the problem.
View 9 Replies
View Related
May 27, 2012
Ever since I bought the E4200 months ago I had no wireless network between my laptops. pc's devices. I discovered now that I do have network (everything cool) when I disable NAT. That is all nice, but I don't have internet then.
View 8 Replies
View Related
Jun 24, 2011
I cannot get the Guest Network feature to work.Even though Guest SSID is enabled, it does not show up on any devices attempting to connect. Manually connecting by entering the Guest SSID fails (not recognized). On devices with the primary 5 and 2.4 GHz configured they do see the third network but without SSID (unknown) and are also unable to connect to it manually using the SSID.I did not try this before 1.0.02. Have rebooted modem and verified all configs (multiple times). The network is live in an office and can't keep screwing with it or drastically changing its settings.
View 9 Replies
View Related
Jan 12, 2013
my general internet connectivity with my e4200.I have a new but similar problem today with the same router.After powering down equipment and moving it around, my wired connections all error. Error in that they will not get an IP address nor will they connect to the internet or each other.My wireless connections still work flawlessly.
I tried powering down the devices over night (to avoid any heating issues) and then powering up but the results are the same. I am obviously missing something, and don't really want to start my network from scratch again...
View 5 Replies
View Related
Jan 7, 2012
I'm trying to block two URL's over the entire network via my E4200. I'm having a heck of a time doing this, I loginto my router via the browser (the web setup) (because I think Cisco Connect on the Mac is about the worst software ever written.) And I go to the Access Restrictions page. There I understand I'll have to use the Internet Access Policy pane to make some more advanced settings than the Parental Control.
I enter a name for my rule, so far so good. Enable it. Go to the applied PC page. Open the page to enter MAC adresses and IP's. I go to the IP Address Range field and entere in the box numbered 01; 192.168.2.2 to 192.168.2.51 which in my case is the enitre network. Save the setttings and close that window.
I don't set Access Restriction to deny becasue that seems to block the entire network.
So I go the the Website Blocking by URL Address option and enter the URL I want to block.
I don't do anything wiht the the Blocked Applications since I don't want to block a specific service or application. So I click Save Settings.
And yet when I go to the URL I want to block it doesn't work! [URL]
View 9 Replies
View Related
Jun 5, 2012
I've been playing around with my E4200 but cannot find the right combination of settings. My problem: I bought the router for cable internet that never happened. In the meantime I am accessing the web using a 3G dongle. Hoewever, while connected to the router (wired or wireless), all the PC's in my home refuses to access the 3G internet - it is as if it wants to use the E4200 to access the net, no matter what. So every time I want to access the internet, I have to disconnect the PC from the home network, and connect with the 3G on that particulat PC. (I have three PC's at home, 1 wired and two wireless). If I set the E4200 to bridge mode, I struggle to find a logical IP address, since I would ideally like to run the network at 192.168.1.X. How do I set the E4200 to allow a home network to be established without having to disconnect everytime I use the 3G on a PC? Also, it seems that if the router doesn't handle the DHCP duties, win7 by default makes the network public, which complicates sharing a lot...
View 5 Replies
View Related
Apr 21, 2012
I can't see my network shares after upgrade altough everything works fine , the network scanner shows all the atatched devices but in Eplorer when I click Network there is nothing shown on two computers running Win7 64.I did downgraded the firmware back to .01 but still no network .
View 3 Replies
View Related
Mar 15, 2013
I was using a netgear wndr 3400 and my network stream never failed. i bought a e4200 v2 and my tv loses streaming capabilities after about 10 to 15 minutes.i have to turn it off to get them back and then it does it again in 15 minutes. i know it is not the tv it wprked fine before the new router.
View 5 Replies
View Related
Aug 4, 2011
I installed the E4200. Internet works fine, and the internet connection is maximum performance. But if I copy a file between laptops, or to my mediaplayer (AC Ryan HD2), the connection is 3MB/s tops. I changed to the 5gHz and N settings, still no change.
View 6 Replies
View Related
Nov 11, 2011
Is it possible to change the Guest Network Name on the E4200? And if so, is it possible to do so without having to do a complete reset of the router and without using the Cisco Connect software?
View 4 Replies
View Related
Mar 10, 2012
I have been using the e4200 for about a week. So far, so good! However, a primary reason I purch it was the ability to share via USB across my network (Files and such). Read the approved USB drives that r compatible and although my specfic drive was not listed (WD, my Passport) I connected it to the e4200 and set a folder called "movies"to share. In this folder I have both bluray rips (25-32GB) and standard rips (5gb or less). Regardless of source, the content was not playable. It buffered like crazy. So, is it as simple as using an approved USB drive and I will be able to share appropriately?
The same folder plays great when connected directly to one of my media streamers USB drive, so don't think the drive/source is bad.
View 2 Replies
View Related
Sep 26, 2011
I can see who is connected via the physical ethernet ports on the E4200 router. However, is there a way to check who is connected to the wireless network. Also is there a way to see rx/tx bytes statistics for all wired and wireless users (including ones that are no longer connected)? I've had the router for 3 months now and it works great but I find there isn't enough operational user info/stats on this router.
View 2 Replies
View Related
