Linksys Wireless Router :: E4200 - Check Who Is Connected To Network?
Sep 26, 2011
I can see who is connected via the physical ethernet ports on the E4200 router. However, is there a way to check who is connected to the wireless network. Also is there a way to see rx/tx bytes statistics for all wired and wireless users (including ones that are no longer connected)? I've had the router for 3 months now and it works great but I find there isn't enough operational user info/stats on this router.
View 2 Replies
ADVERTISEMENT
Jan 14, 2012
If I were to take a e4200v2 and use it as an access point (disable DHCP), would the USB port connected to a Hard Drive still function as network storage?
View 5 Replies
View Related
Jul 11, 2011
I've used Netgear & other routers for years; I was able to see the devices connected over ethernet & wifi through the router configuration utility. Cisco's interface looks poor; there is no way to see the connected devices.Many of the devices I have have a 5 Ghz radio and some don't so i need to see at what speeds they are connecting at.Or does Cisco not provide this utility? I am surprised that a high-end product from Cisco does not have this function.
View 9 Replies
View Related
Sep 2, 2011
I need a small number of computers connected to the Internet through the E4200.E4200 must be connected to the switch via the LAN port.The basic network is a network of class A - 10.xxx/255.0.0.0.How do I do?E4200 can not enter a mask of 255.0.0.0.
View 1 Replies
View Related
Jul 14, 2011
I tried searching through the threads but didn't see anything on this. Recently bought the E4200 so that when guests come by they can use a separate network instead of mine. I have guest network set up for one user but I am able to connect more than one computer to the guest network.
View 9 Replies
View Related
Dec 16, 2011
I'm trying to connect an Epson Stylus Color 740 USB printer to a newly purchased E4200 wireless router. I've upgraded to the latest Cisco Connect software and to version 1.0.0.3 router firmware. I get the message "A non-supported device is connected to your router's USB port. Disconnect that device and follow the steps below to connect a USB printer to your router." Cisco support was not beneficial.
View 1 Replies
View Related
Sep 15, 2012
I have recently switched to fibre optics and I have decided to reuse my Linksys E4200 that was previously used with a cable network. However, After installing the router using the disk provided I was unable to connect to the internet even though my computer was able to connect with the router. What can I do to solve this prob. I have tried restarting the modem to the factory settings and the same problem recurs.P.S. The modem was installed to another router provided by my service provider.
View 6 Replies
View Related
Jan 3, 2012
I just installed a E4200, and found that once I connected my Homeplug Powerline to E4200, the connected (wired / wireless) computer (with E4200) connection will be dropped. The connection become normal again once I disconnected the Homeplug with E4200.
View 5 Replies
View Related
Oct 31, 2011
I'm thinking of upgrading from my Linksys WRT54G router to the E4200 and though I've goggled. Also, are there no LEDs on this unit to tell you the status of what's connected?
E3000WRT-54GWVC-80N
View 3 Replies
View Related
Apr 11, 2013
Region : Canada
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 3.13.23
ISP : Teksavvy
how can I see who connected to my router?
View 2 Replies
View Related
Nov 28, 2011
I just bought a new Linksys E4200, and connected it about an hour ago. I have a 30Mbps internet connection when connected direct to the modem, but when connected wired to the router, max speeds are 8Mbps.
View 2 Replies
View Related
Jul 10, 2011
U just bought a new E4200 router to enjoy 5ghz band for the first time.I noticed the range at my house of the 5gh is smaller than 2.4 is that right?one of my pc is having trouble keep connected to the 5ghz signal or the router doenst respond to it, is there a way to improve that signal?
View 2 Replies
View Related
Jun 30, 2012
I have the E4200 with latest firmware . When I connect my computer to the E4200 and that to my modem im getting about 50mb speed. If I disconnect the E4200 and connect my computer straight to the modem I get about 95mb speed?I have the Virgin Broadband 100mb service and all is working fine at their end.
View 2 Replies
View Related
Dec 18, 2011
having wireless G network coexist with Wireless N network on e4200.
I have an existing wireless G network with ActionTec router for VERIZON FIOS. I just added the E4200 router for wireless N. I have latest firmware, 1.0.03. Version 1 hardware.
We are getting a couple of laptops for holidays and would like these to be able use wireless N. I have older laptop/itouch/roku device that use wireless G/B network from ActionTec router. I would like to keep the ActionTec router for wireless G/B, so that both 2.4 and 5.0 ghz networks are Wireless N only.
I have both routers configured so that ActionTec is primary with DHCP and the e4200 is secondary, setup in bridge mode, with DHCP off and static ip of 192.168.1.2. Used this for guidance -> [URL]
I have one SID for ActionTec Wireless G network and this is set for Channel 1
I have a different SID for e4200 Wireless N network, same for 2.4 and 5.0 and I left defaults on other wireless settings.
View 5 Replies
View Related
Feb 21, 2013
I have the wireless guest network up and running just fine. But, I need to also connect to the router's quest network via one of the ethernet ports. Can I just give the LAN-conencted PC a 192.168.3.x static IP to access the guest network? I am assuming there is no VLAN functionality...
And even better, can I set up a DHCP relationship to that port? So that any device plugged into the port will get a IP on that subnet?
View 4 Replies
View Related
Aug 21, 2011
I have e4200 router set up with different SSIDs for 2.4ghz and 5ghz. My laptop (Lenovo x220 with Intel 6205 wireless adapter) can't see the 5ghz network. I've tried changing the channel for the 5ghz network and it didn't fix the problem.
View 9 Replies
View Related
May 27, 2012
Ever since I bought the E4200 months ago I had no wireless network between my laptops. pc's devices. I discovered now that I do have network (everything cool) when I disable NAT. That is all nice, but I don't have internet then.
View 8 Replies
View Related
Jun 24, 2011
I cannot get the Guest Network feature to work.Even though Guest SSID is enabled, it does not show up on any devices attempting to connect. Manually connecting by entering the Guest SSID fails (not recognized). On devices with the primary 5 and 2.4 GHz configured they do see the third network but without SSID (unknown) and are also unable to connect to it manually using the SSID.I did not try this before 1.0.02. Have rebooted modem and verified all configs (multiple times). The network is live in an office and can't keep screwing with it or drastically changing its settings.
View 9 Replies
View Related
Jan 12, 2013
my general internet connectivity with my e4200.I have a new but similar problem today with the same router.After powering down equipment and moving it around, my wired connections all error. Error in that they will not get an IP address nor will they connect to the internet or each other.My wireless connections still work flawlessly.
I tried powering down the devices over night (to avoid any heating issues) and then powering up but the results are the same. I am obviously missing something, and don't really want to start my network from scratch again...
View 5 Replies
View Related
Jan 7, 2012
I'm trying to block two URL's over the entire network via my E4200. I'm having a heck of a time doing this, I loginto my router via the browser (the web setup) (because I think Cisco Connect on the Mac is about the worst software ever written.) And I go to the Access Restrictions page. There I understand I'll have to use the Internet Access Policy pane to make some more advanced settings than the Parental Control.
I enter a name for my rule, so far so good. Enable it. Go to the applied PC page. Open the page to enter MAC adresses and IP's. I go to the IP Address Range field and entere in the box numbered 01; 192.168.2.2 to 192.168.2.51 which in my case is the enitre network. Save the setttings and close that window.
I don't set Access Restriction to deny becasue that seems to block the entire network.
So I go the the Website Blocking by URL Address option and enter the URL I want to block.
I don't do anything wiht the the Blocked Applications since I don't want to block a specific service or application. So I click Save Settings.
And yet when I go to the URL I want to block it doesn't work! [URL]
View 9 Replies
View Related
Jun 5, 2012
I've been playing around with my E4200 but cannot find the right combination of settings. My problem: I bought the router for cable internet that never happened. In the meantime I am accessing the web using a 3G dongle. Hoewever, while connected to the router (wired or wireless), all the PC's in my home refuses to access the 3G internet - it is as if it wants to use the E4200 to access the net, no matter what. So every time I want to access the internet, I have to disconnect the PC from the home network, and connect with the 3G on that particulat PC. (I have three PC's at home, 1 wired and two wireless). If I set the E4200 to bridge mode, I struggle to find a logical IP address, since I would ideally like to run the network at 192.168.1.X. How do I set the E4200 to allow a home network to be established without having to disconnect everytime I use the 3G on a PC? Also, it seems that if the router doesn't handle the DHCP duties, win7 by default makes the network public, which complicates sharing a lot...
View 5 Replies
View Related
Apr 21, 2012
I can't see my network shares after upgrade altough everything works fine , the network scanner shows all the atatched devices but in Eplorer when I click Network there is nothing shown on two computers running Win7 64.I did downgraded the firmware back to .01 but still no network .
View 3 Replies
View Related
Mar 15, 2013
I was using a netgear wndr 3400 and my network stream never failed. i bought a e4200 v2 and my tv loses streaming capabilities after about 10 to 15 minutes.i have to turn it off to get them back and then it does it again in 15 minutes. i know it is not the tv it wprked fine before the new router.
View 5 Replies
View Related
Aug 4, 2011
I installed the E4200. Internet works fine, and the internet connection is maximum performance. But if I copy a file between laptops, or to my mediaplayer (AC Ryan HD2), the connection is 3MB/s tops. I changed to the 5gHz and N settings, still no change.
View 6 Replies
View Related
Nov 11, 2011
Is it possible to change the Guest Network Name on the E4200? And if so, is it possible to do so without having to do a complete reset of the router and without using the Cisco Connect software?
View 4 Replies
View Related
Mar 10, 2012
I have been using the e4200 for about a week. So far, so good! However, a primary reason I purch it was the ability to share via USB across my network (Files and such). Read the approved USB drives that r compatible and although my specfic drive was not listed (WD, my Passport) I connected it to the e4200 and set a folder called "movies"to share. In this folder I have both bluray rips (25-32GB) and standard rips (5gb or less). Regardless of source, the content was not playable. It buffered like crazy. So, is it as simple as using an approved USB drive and I will be able to share appropriately?
The same folder plays great when connected directly to one of my media streamers USB drive, so don't think the drive/source is bad.
View 2 Replies
View Related
Feb 28, 2013
I cannot get my iPhone 5 to access my wireless network (Linksys E4200) since I reset the router. It asks for the password but doesn't accept it. I'm a newbie so be gentle with me! MSZ
View 2 Replies
View Related
Jul 8, 2011
My old dLink DIR-655 router could serve as an NTP server for all the computers on my network. It would get the time from the dLink NTP time source and allow me to sync all the systems on my home network off the DIR-655.
I had to replace it with this new E4200 but don't see an option for it to act as a time source for my internal network.
Can this router be used for this function?
View 1 Replies
View Related
Mar 17, 2013
The task is to share Internet via Wireless router for visitors without any Proxy/Windows Domain authentication.We have:1) Windows based Domain with Active Directory Users, with no DHCP setup, only Static IPs allowed. Used as a DNS server, the IP-address is 192.168.1.1, Domain name, say, Internet Connection via Proxy server which authenticates users via above-mentioned DNS server, the Proxy server IP-address is 192.168.1.3, ruled by MS TMG (ISA server)3) A Wi-Fi Router Cisco E4200.The local area network is wired and works fine. Domain users are happy.The idea is to make visitors happy with a free Internet connection without wiring them into the LAN.So:1) Respected visitors would not have to set up static IP-adresses on their devices to connect to Internet and2) Respected visitors would not have to enter domain credentials to get access to Internet, but3) Network security should not be jeopardized.
View 3 Replies
View Related
Dec 20, 2011
I got a problem with my setup main computer, It work wery god wireless, with very fine speed about 82 mbit in and 24 mbit out. The problem is that it almost dont work at all with cable, even if i turn off the wireless network, the speed is about 2-3 mbit in and about 6-7 mbit outAll other computers, tv. printer wireless work very fine.
View 1 Replies
View Related
Sep 1, 2011
I purchased a e4200 in hopes that its dual band capability would allow us to run a 2.4ghz network for certain devices and a 5ghz for everyone else. I am able to setup the router and connect but it seems when the 2.4ghz network drops the router drops all connections.
At first I had the networks setup with the same ssid, then changed the 5ghz network to a new ssid but was still losing connection when the 2.4ghz network dropped. This may be a simple routing issue i am overlooking (bit of a network newbie).
View 3 Replies
View Related
Jul 30, 2011
So, with the latest firmware update I could add a second e4200 to my network to use as a bridge or access point? What I need is another device in my living room that can pick up the wireless signal and dish out network connectivity to my receiver, xbox360, and ps3. With the new firmware update can this be done with a second e4200? How does one connect to each e4200 on the network for setup (dohave to change the default ip address of 1?)I just bought a trendnet TEW-687GA 450 mb/s wireless gaming adapter and a trendnet 5 port switch to accomplish what I mentioned above. I'm just wondering if there is an advantage to switching over to two e4200's. The trendnet adapater does not have a 5ghz channel.
View 2 Replies
View Related
Dec 12, 2011
just picked up a E4200 v1.
does the mac filtering also apply to the quest network?
I normally have it set to allow macs for the wireless devices i own.
does the mac filtering apply to the quest network?
View 1 Replies
View Related
