I was using a netgear wndr 3400 and my network stream never failed. i bought a e4200 v2 and my tv loses streaming capabilities after about 10 to 15 minutes.i have to turn it off to get them back and then it does it again in 15 minutes. i know it is not the tv it wprked fine before the new router.
View 5 Replies
I can't see my network shares after upgrade altough everything works fine , the network scanner shows all the atatched devices but in Eplorer when I click Network there is nothing shown on two computers running Win7 64.I did downgraded the firmware back to .01 but still no network .
View 3 Replies View RelatedI have an E4200 v1 wireless router. Intermittently, my hard wired laptop (and hard wired desktop) loose Internet connnectivity and when I look at the 4200 I see the status light flashing slowly like it was just rebooted. I am runnong 1.0.04, have reset to factory, reflashed the 1.0.04 code and done a 30-30-30 reset (so far no drops since the 30-30-30 reset but we'll see).
View 9 Replies View RelatedI have a brand new E4200 constantly losing internet connection (both wireless and wired). I have a ADSL connection to the internet, last router I had did not have the same issue. I also have a Cisco ASA 5505 for work connected to the ADSL modem and is not experiencing any disconnect issues. All computers connected to the router is losing internet connection, local lan keeps working. The internet connection gets back again after a 10-15 minutes or when resetting / turning off the router.
I have tried the following;
Changed ethernet cables
Disconnected the ASA 5505
Turned off wireless
Upgraded the firmware
Reseted to factory settings
is it worth it? I still cant stream some of my higher quality 6+gb .mpg video files with the v1 with the .03 firmware. I notice the v2 says faster or better HD video. [URL]
View 5 Replies View RelatedThe file uploads fine, but I get an error message saying the router can't be updated atthe moment. I want to do the update because as of now, the router can't see my drive connected on usb (one ntfs partition and another one called wbfs, maybe that one is causing the issue about the drive).
View 2 Replies View RelatedI downloaded the firmware from the Linksys site. I'm using IE v9 on a Win7 Pro x32. I'm using the E4200 as an access point so DHCP is disabled, no cable in the WAN port.
I uploaded the firmware but it seems to be stuck for 30 minutes at 98%. I read some threads saying it takes a while, but I'm not sure if it is locked up. The screen says not to interrupt the process so I don't want to reboot/reset and brick the router.
I currently have Model name: Linksys E4200 Firmware version: 1.0.04 build 11 Software version: 1.4.12100.0
I'm trying to upgrade to the second and most up to date version. (Version: 2.0) firmware. Any links or way to do this? I tried doing it through my router settings under administration -> firmware upgrade but it won't update automatically. I have to find the actual update file and update the firmware through that.
I just bought a Cisco E4200 (from someone on Ebay, so returning is probably not an option). I was in the process of setting it up when it wanted to do a Router Update. Unfortunately, it did not specifically say to not do it WIRELESS. We had a disconnection in the upgrade process. Now the Power light just blinks. I can ping it from a hard-wired PC, but cannot get to the Administration Web page to retry the firmware update (I did download it from the site). Also Cisco Connect cannot connect to the router.
Oh Yes, I have tried holding reset button for 30 seconds, unplugging for 30 seconds, and replugging in the router. I do not get any different results.
automatic firmware upgrade my E4200 can no longer be accessed.
View 6 Replies View RelatedThe issue is Windows7 (notebook ASUS N61Ja connected through Wi-Fi) loses and can not find again network HDD storage (Western Digital My Book Live 3TB). Rebooting of the notebook works but after I close HDD folder window the issue comes back. The issue exists only with Wi-Fi connection. Everything is fine using LAN connection.
View 1 Replies View RelatedAny problems with the guest network on the ea4500 with the cloud firmware? I am losing guest clients after about 24 hours and the re-authentication fails. you enter the guest password and nothing happens until you reboot the router.
View 2 Replies View Relatedhaving wireless G network coexist with Wireless N network on e4200.
I have an existing wireless G network with ActionTec router for VERIZON FIOS. I just added the E4200 router for wireless N. I have latest firmware, 1.0.03. Version 1 hardware.
We are getting a couple of laptops for holidays and would like these to be able use wireless N. I have older laptop/itouch/roku device that use wireless G/B network from ActionTec router. I would like to keep the ActionTec router for wireless G/B, so that both 2.4 and 5.0 ghz networks are Wireless N only.
I have both routers configured so that ActionTec is primary with DHCP and the e4200 is secondary, setup in bridge mode, with DHCP off and static ip of 192.168.1.2. Used this for guidance -> [URL]
I have one SID for ActionTec Wireless G network and this is set for Channel 1
I have a different SID for e4200 Wireless N network, same for 2.4 and 5.0 and I left defaults on other wireless settings.
I have the wireless guest network up and running just fine. But, I need to also connect to the router's quest network via one of the ethernet ports. Can I just give the LAN-conencted PC a 192.168.3.x static IP to access the guest network? I am assuming there is no VLAN functionality...
And even better, can I set up a DHCP relationship to that port? So that any device plugged into the port will get a IP on that subnet?
I have e4200 router set up with different SSIDs for 2.4ghz and 5ghz. My laptop (Lenovo x220 with Intel 6205 wireless adapter) can't see the 5ghz network. I've tried changing the channel for the 5ghz network and it didn't fix the problem.
View 9 Replies View RelatedEver since I bought the E4200 months ago I had no wireless network between my laptops. pc's devices. I discovered now that I do have network (everything cool) when I disable NAT. That is all nice, but I don't have internet then.
View 8 Replies View RelatedI cannot get the Guest Network feature to work.Even though Guest SSID is enabled, it does not show up on any devices attempting to connect. Manually connecting by entering the Guest SSID fails (not recognized). On devices with the primary 5 and 2.4 GHz configured they do see the third network but without SSID (unknown) and are also unable to connect to it manually using the SSID.I did not try this before 1.0.02. Have rebooted modem and verified all configs (multiple times). The network is live in an office and can't keep screwing with it or drastically changing its settings.
View 9 Replies View Relatedmy general internet connectivity with my e4200.I have a new but similar problem today with the same router.After powering down equipment and moving it around, my wired connections all error. Error in that they will not get an IP address nor will they connect to the internet or each other.My wireless connections still work flawlessly.
I tried powering down the devices over night (to avoid any heating issues) and then powering up but the results are the same. I am obviously missing something, and don't really want to start my network from scratch again...
I'm trying to block two URL's over the entire network via my E4200. I'm having a heck of a time doing this, I loginto my router via the browser (the web setup) (because I think Cisco Connect on the Mac is about the worst software ever written.) And I go to the Access Restrictions page. There I understand I'll have to use the Internet Access Policy pane to make some more advanced settings than the Parental Control.
I enter a name for my rule, so far so good. Enable it. Go to the applied PC page. Open the page to enter MAC adresses and IP's. I go to the IP Address Range field and entere in the box numbered 01; 192.168.2.2 to 192.168.2.51 which in my case is the enitre network. Save the setttings and close that window.
I don't set Access Restriction to deny becasue that seems to block the entire network.
So I go the the Website Blocking by URL Address option and enter the URL I want to block.
I don't do anything wiht the the Blocked Applications since I don't want to block a specific service or application. So I click Save Settings.
And yet when I go to the URL I want to block it doesn't work! [URL]
I've been playing around with my E4200 but cannot find the right combination of settings. My problem: I bought the router for cable internet that never happened. In the meantime I am accessing the web using a 3G dongle. Hoewever, while connected to the router (wired or wireless), all the PC's in my home refuses to access the 3G internet - it is as if it wants to use the E4200 to access the net, no matter what. So every time I want to access the internet, I have to disconnect the PC from the home network, and connect with the 3G on that particulat PC. (I have three PC's at home, 1 wired and two wireless). If I set the E4200 to bridge mode, I struggle to find a logical IP address, since I would ideally like to run the network at 192.168.1.X. How do I set the E4200 to allow a home network to be established without having to disconnect everytime I use the 3G on a PC? Also, it seems that if the router doesn't handle the DHCP duties, win7 by default makes the network public, which complicates sharing a lot...
View 5 Replies View RelatedI installed the E4200. Internet works fine, and the internet connection is maximum performance. But if I copy a file between laptops, or to my mediaplayer (AC Ryan HD2), the connection is 3MB/s tops. I changed to the 5gHz and N settings, still no change.
View 6 Replies View RelatedIs it possible to change the Guest Network Name on the E4200? And if so, is it possible to do so without having to do a complete reset of the router and without using the Cisco Connect software?
View 4 Replies View RelatedI have been using the e4200 for about a week. So far, so good! However, a primary reason I purch it was the ability to share via USB across my network (Files and such). Read the approved USB drives that r compatible and although my specfic drive was not listed (WD, my Passport) I connected it to the e4200 and set a folder called "movies"to share. In this folder I have both bluray rips (25-32GB) and standard rips (5gb or less). Regardless of source, the content was not playable. It buffered like crazy. So, is it as simple as using an approved USB drive and I will be able to share appropriately?
The same folder plays great when connected directly to one of my media streamers USB drive, so don't think the drive/source is bad.
I can see who is connected via the physical ethernet ports on the E4200 router. However, is there a way to check who is connected to the wireless network. Also is there a way to see rx/tx bytes statistics for all wired and wireless users (including ones that are no longer connected)? I've had the router for 3 months now and it works great but I find there isn't enough operational user info/stats on this router.
View 2 Replies View RelatedI cannot get my iPhone 5 to access my wireless network (Linksys E4200) since I reset the router. It asks for the password but doesn't accept it. I'm a newbie so be gentle with me! MSZ
View 2 Replies View RelatedMy old dLink DIR-655 router could serve as an NTP server for all the computers on my network. It would get the time from the dLink NTP time source and allow me to sync all the systems on my home network off the DIR-655.
I had to replace it with this new E4200 but don't see an option for it to act as a time source for my internal network.
Can this router be used for this function?
The task is to share Internet via Wireless router for visitors without any Proxy/Windows Domain authentication.We have:1) Windows based Domain with Active Directory Users, with no DHCP setup, only Static IPs allowed. Used as a DNS server, the IP-address is 192.168.1.1, Domain name, say, Internet Connection via Proxy server which authenticates users via above-mentioned DNS server, the Proxy server IP-address is 192.168.1.3, ruled by MS TMG (ISA server)3) A Wi-Fi Router Cisco E4200.The local area network is wired and works fine. Domain users are happy.The idea is to make visitors happy with a free Internet connection without wiring them into the LAN.So:1) Respected visitors would not have to set up static IP-adresses on their devices to connect to Internet and2) Respected visitors would not have to enter domain credentials to get access to Internet, but3) Network security should not be jeopardized.
View 3 Replies View RelatedI got a problem with my setup main computer, It work wery god wireless, with very fine speed about 82 mbit in and 24 mbit out. The problem is that it almost dont work at all with cable, even if i turn off the wireless network, the speed is about 2-3 mbit in and about 6-7 mbit outAll other computers, tv. printer wireless work very fine.
View 1 Replies View RelatedI purchased a e4200 in hopes that its dual band capability would allow us to run a 2.4ghz network for certain devices and a 5ghz for everyone else. I am able to setup the router and connect but it seems when the 2.4ghz network drops the router drops all connections.
At first I had the networks setup with the same ssid, then changed the 5ghz network to a new ssid but was still losing connection when the 2.4ghz network dropped. This may be a simple routing issue i am overlooking (bit of a network newbie).
So, with the latest firmware update I could add a second e4200 to my network to use as a bridge or access point? What I need is another device in my living room that can pick up the wireless signal and dish out network connectivity to my receiver, xbox360, and ps3. With the new firmware update can this be done with a second e4200? How does one connect to each e4200 on the network for setup (dohave to change the default ip address of 1?)I just bought a trendnet TEW-687GA 450 mb/s wireless gaming adapter and a trendnet 5 port switch to accomplish what I mentioned above. I'm just wondering if there is an advantage to switching over to two e4200's. The trendnet adapater does not have a 5ghz channel.
View 2 Replies View Relatedjust picked up a E4200 v1.
does the mac filtering also apply to the quest network?
I normally have it set to allow macs for the wireless devices i own.
does the mac filtering apply to the quest network?
I have an E4200 with a 500GB WD hard drive attached to the USB port. I also have 3 computers on the network named "THINK", "PC", and "DELL". THINK is mixed Wired and Wireless - depending on what I'm doing - Win7 Professional, DELL is plugged into a Range Extender. (RE1000) - WinXP (This one isn't as important: It's an older machine) PC is always hardwired. - Win7 Ultimate, Recently, THINK has unable to see DELL, OR even the HD connected to the router, but it can see PC. It can also see the HD as a media device - just not as a computer or device I can browse as it does on PC.However, PC can see everything: THINK, DELL, AND the HD and can access them all the way I would like it to be. Also - MY PS3 DOES see the Media Share and can access it. Edit: Also just discovered both internal and external FTP no long works. Why can't THINK see the HD connected to the router regardless if I'm wired or wireless? As far as I can tell, all the settings are identical on both THINK and PC. Is there a router setting I'm missing? IPV6 is disabled and I've treid the basic disabling of HOMEGROUP and anything that goes with it - but nothing yet.
View 9 Replies View Relatedmy old D-link DGL-4300 was rock steady showing 54 Mbps constant speed (link rate) (in Windows 7 Home Premium 32 bit Wireless Network Connection Status window). The new E4200 jumps around from 72 Mbps to 114 Mbps to 130 Mbps to 144 Mbps. However, it mainly stays at 72 Mbps. I have seen 150 Mbps briefly but I have never seen 300 Mbps. I have even placed my laptop within 2 -3 ft of the router and have a strong signal (4 bars) but I still have the same link rate issue. I would think that Windows would show 300 Mbps link rate for my connection when it is that close to the router. My laptop is a Toshiba with an integrated Intel WiFi Link 5100 AGN wireless adapter. My son also has a Toshiba laptop with the same wireless adapter but he gets lower speeds than mine due to the fact that he is 50' away in another room in the house. His connection also jumps around but it is at lower link rates than mine.
View 9 Replies View Related
