I cannot get my iPhone 5 to access my wireless network (Linksys E4200) since I reset the router. It asks for the password but doesn't accept it. I'm a newbie so be gentle with me! MSZ
View 2 RepliesBoth the iPod and iPhone were on the network and working and now neither is on and don't detect the network at all. Have turned off and on both devices as well as the router to no avail. My mini Mac is up and running and has been all day.
View 1 Replies View RelatedI recently purchased an E4200, but I am experiencing slow/inconsistent performance and connection problems with iPhone 3G, 3GS and 4. The iPhones are running the latest firmware 4.3. The E4200 has also been updated to the latest firmware 1.0.01 build 10. I do not experience these problems with various laptops, and I did not experience them with a previous Cisco router WRT610N, nor with a D-link DIR825 in another location. The security is set to WPA2 Personal and all the other settings are the same from the prior router. If I disable the security, I do not experience the connection problems, but still experience the slow performance. If I switch back to the WRT610N, I do not experience any problems. this a E4200 firmware issue yet to be resolved?
View 9 Replies View RelatedI have a E4200 fw 1.0.03 my pc, laptop connect to E4200 is OK but have a problem with my iphone 3Gs iPhone 3Gs connect to E4200 at day is OK althought sometime loss packet but at night (after 17:30) iPhone can't connect to E4200, althought I don't config anything.This is my E4200 configure fw: 1.0.03 No set schedule access internet
At Day This is a log DHCP when iPhone(MAC: 00:26:bb:fb:29:a0) connect to e4200 at Day Sun, 04 Dec 2011 07:11:00 received REQUEST from 00:26:bb:fb:29:a0 Sun, 04 Dec 2011 07:11:00 sending ACK to 192.168.1.136 get IP very fast ping packets at day (loss some packets):
But at Night everything change althought I don't config anything on e4200This is a log DHCP when iPhone(MAC: 00:26:bb:fb:29:a0) connect to e4200 at Night Sat, 03 Dec 2011 22:11:20 received REQUEST from 00:26:bb:fb:29:a0 Sat, 03 Dec 2011 22:11:22 received REQUEST from 00:26:bb:fb:29:a0 Sat, 03 Dec 2011 22:11:27 received DISCOVER from 00:26:bb:fb:29:a0 Sat, 03 Dec 2011 22:11:28 sending OFFER to 255.255.255.255 with 192.168.1.135 Sat, 03 Dec 2011 22:11:28 received DISCOVER from 00:26:bb:fb:29:a0 Sat, 03 Dec 2011 22:11:28 sending OFFER to 255.255.255.255 with 192.168.1.135 Sat, 03 Dec 2011 22:11:31 received REQUEST from 00:26:bb:fb:29:a0 Sat, 03 Dec 2011 22:11:31 sending ACK to 192.168.1.135 Sat, 03 Dec 2011 22:11:32 received REQUEST from 00:26:bb:fb:29:a0 Sat, 03 Dec 2011 22:11:32 sending ACK to 192.168.1.135 Sat, 03 Dec 2011 22:11:34 received REQUEST from 00:26:bb:fb:29:a0 Sat, 03 Dec 2011 22:11:34 sending ACK to 192.168.1.135
Very difficult to get IP from e4200 at night, sometimes getting IP but not on the Internet, sometimes can not get IP and iPhone get message "unable to join the network "ciscoTNTn""ping packets at night (can't ping):
While iPhone is connected to the Draytek Vigor2600VG good no matter day or night.I re-upgrade fw 1.0.03 and restore factory defaults but still not fixed.Is that a bugs ?
all other devices have excelent signal
View 5 Replies View RelatedI have Linksys configured with IP 192.168.0.x and my local network ip 192.168.1.x have firewall connected to Adtrans box that gives us internet access via T1 line and other port is connected to the switch. Wireless router is connected to the switch using internet port.I can connect to wireless using iphone but emails don't work when connected to wireless. I tried to connect laptop to wireless is does not connect.
View 9 Replies View RelatedI have an E4200, and upgraded to Connect Cloud. It was buggy, and so I downgraded to the firmware before that. I have all the computers working fine in the house except my desktop. it connects fine to the network, can see the other computers on the network, can even do a windows update. But when I go to use google chrome or internet explorer it just wont access the internet. It doesn't seem to work either if it is a wired connection, or a wireless connection It was fine before the upgrade and subsequent downgrade. It was on this desktop that i installed and uninstalled thew Connection cloud. I know enough to set up the network but when it doesn't work
View 4 Replies View RelatedI have been having issues with my home network since upgrading my router from a WRT54GS to an E4200. Prior to this I had no difficulty in accessing my home group or my home network. I have 2 laptops, both are running Windows 7 Ultimate, one is x64 and one is x32.
Laptop 1 (x-64) can access my home network in all its glory ONLY wirelessly...plug in the Ethernet cable and I can't access laptop 2 or my network storage...Laptop 1 is also unable to join my homegroup even after deleting the old one and creating a new one.
Laptop 2 (x-32) can access my home network in most of its glory ONLY wired...unplug the Ethernet cable and I can't access my network storage and it becomes unavailable to Laptop 1 over the network. Laptop 2 is also not able to connect to Laptop 1 even though Laptop 1 can (sometimes) access files from Laptop 2's shared folders.
Also Laptop 2 cannot see a home group created by Laptop 1, but can create a homegroup that Laptop 1 can see but CAN'T join.I have run all the trouble shooters that the system throws at me to no avail, they all say that I have an unknown network error that it can't fix.I do have internet access on both laptops regardless of wired or wireless, and I spent over 2 hours with Cisco "senior" tech support only to be disconnected and realize that they had no clue about this new router..
I had PCs, Macs and other devices (iphone, itouch) able to connect fine to the WRT610n. I moved to an apartment and when I turned the network on all the devices could connect expect for the iphone and itouch. I have tried turning the wireless security off and MAC filtering off . I get the same "Unable to join the network" message.
View 7 Replies View RelatedI have a Linksys WRT120N which had suddenly and unexectedly stopped working after disconnecting my roku box. I didnt worry about it until I got an Iphone and now .I was able to re-establish the wireless connection on my netbook today after a ton of research and messing around with the settings and then downloaded network magic, which finally fixed the problem. I believe that it automatically transmitted the WEP key to the Netbook, which is what I am missing when I try to log into the network on the Iphone.How do I get this password to show up on Network Magic? When I look at the settings, it does not show the actual numbers, they are hidden.
View 6 Replies View RelatedSet up our E3000 following the set-up guide. However, wireless devices (laptop, iPhone) recognize the network, but cannot connect. There's no prompt for a password or anything.
View 6 Replies View RelatedMy EA4500 router seems to drop mine and my wife's iPhone wifi connection at what appears to be the edge of my router's range. When we come back in range, our iPhone's intermittently give the error "Unable to join network.". And we're stuck in that mode. When I check the Devices menu in the CCC interface, I notice the iPhone device is configured and still online. However the "x" box to delete the device is greyed out because it's online. So how do I get out of this state and have my iPhone connect
View 2 Replies View RelatedI reset the wap610N,after establishing connection, my iphone see my network domain but does not connect. I heard of dual band setting,how do i go about that. What must i do to establish connection with the iphone.
View 4 Replies View RelatedI've been trying to get FTP Running up on my router for some time now.
I know my current WAN address and have setup a specified folder on my E4200 for the FTP partition. A username for myself has been created with login info and I have forwarded the port I have specified on my router's FTP configuration page.
I try to log into the server, but whenever I try to log into it, I keep getting a "incorrect login information" message back at me.
If I cancel out of that then I get an error message saying it can't find the specified folder and to check the address of the server.
I know the login information information is correct and I've tried changing the password to others of varying lengths.
I've also tried changing the port I'm running the FTP off of incase my ISP has blocked that port, nothing works.
i have installed lutron lighting in my home and need to configure e4200 so i can access it from outside home with iphone application. Lutron manual says to go to VPN iphone setting and add PPTP connection, server, account and password. I need to do same on e4200 but not sure where to go create pptp connection, accounts and passwords?
View 4 Replies View RelatedI have my main router, a E4200v2 which I use as a router and it provides wireless signal throughout my house, however reception is not as strong on the upper floor and there is a slight dead spot, so I purchased an E4200 for the uppermost floor.I set the E4200 to bridge mode so it will act solely as an AP.However connecting the two routers LAN to LAN and the AP does not access the internet.Setting a static IP for the router, instead of acquiring one via DHCP causes me to not be able to access the admin page on the AP.
Connecting WAN on the E4200 to the LAN on the v2 does not work either.My goal here is to have my main router on 192.168.1.1 and the AP on 192.168.1.2 where I can access the admin settings for both routers in case I need to make changes.
Just got a new hard drive installed on my laptop, and now for some reason I can not access my router. I am connected to the internet, and everything is fine there, but when I type the 192.168.1.1 and enter admin as the password, it shows that I am unauthorized.
I have a Linksys E4200 router
I posted before about my problem in forwarding certain ports in a LAN-to-WAN cascaded router setup, and I finally gave up looking for a solution, and went for a LAN-to-LAN. On the internet there is many articles to be found on how to accomplish the setup, but none of them is complete, and as such, I think I really screwed up someplace. My setup: ISP modem/router (192.168.1.1 / 255.255.255.0) DHCP enabled, and DHCP address range 3-100 NAT configured Static IP address for a Synology NAS connected to the E4200 SSID id_1
Then the E4200 Internet connection type: I set to Static IP IP 192.168.1.2 Subnet mask 255.255.255.0 Default gateway: 0.0.0.0 (to disable the WAN)
Then, the network setup: Router IP: 192.168.1.2 gave me the error that WAN and LAN IPs were identical. I played around quite some time but always got an “illegal value” error. Then finally I put the IP to 192.168.0.1 (IP I had in LAN-to-WAN) and this was accepted. And subnet mask: 255.255.255.0 The SSID I left unchanged from what it was, id_2 (also gives me the advantage that I know to which router I am connected)
I rebooted the E4200, and I was connected. But … I am unable to connect to the E4200 configuration page, and even Cisco Connect cannot establish the connection.
I recently put in a surveillance system with remote access. I have an application on my android phone and it can be viewed by any browser. While I am connected to my network these functions work fine, on my phone and any desktop/laptop. The problem happens when I try to view remotely, off my network. I had this setup on my Netgear router before I got my new fancy schmancy Cicso router becaue the netgear wasn't cutting the cheese in keeping my wireless connectionstory.So here is what I got. I need 3 ports forwarded for this work, and how I got it work on my Netgear. I have these 3 ports forwarded as single ports. I have them forwarded in a range and I have port triggering turned on. No matter what or which combination of these few things I try, I can't access the DVR remotely, again unless I'm local to MY network.Some additional notes - the DVR has a static address and that address has been reserved in the DHCP settings of the router.
View 5 Replies View RelatedI have a problem te access e4200 with web access on a iMac with Lion 10.7. I try to connect with standard Safari.With 192.168.1.1. it won't open, if I look voor IP address it should be 192.168.0.1. now the login screen opens but now I can't login with clean name en password "admin" it gives an error.I also can't install Ciso Connect from CD, it gives a error not right version!.Is there anyone that use iMac with E4200 and Sonos zone player?
View 3 Replies View Relatedhow to setup the E4200 so that I can access the media server when I am in office? I was browsing on the Cisco website and unable to find it.
View 8 Replies View RelatedIf you have MAC filter enabled with the E4200 Firmware Version: 1.0.01 you cannot connect to guest.
View 2 Replies View Relatedi enable guest access, when connecting though any device it doesn't ask for password but allows access straight away. I've tried changing the password, but no luck.
View 3 Replies View RelatedI have a Linksys E4200 router with firmware version 1.0.02. I am using a Macbook Pro. I can connect to a VPN server with the default VPN client software, but it kills my internet connection and disables connecting to SMB
View 5 Replies View RelatedI've got an E4200 at my house. I'd like to know if it's possible for my to establish a VPN connection from a remote location to login to my E4200 to get access to my computers behind the firewall.
View 1 Replies View RelatedI cannot connect to my company’s VPN after installing the current firmware (FW_E4200_1.0.02.013_US_20110524) on my E4200 router. Version 1.0.01 was on the router when I received it, and it worked without issues. As soon as I upgraded version 02, I could not initialize a VPN connection. When I try to start a VPN session, I get a "page not found" error when attempting to initiate SSL VPN service using a Microsoft Forefront Unified Access Gateway. VPN pass through is enabled for all protocols in the e4200’s setup. As soon as I revert to firmware 01, everything works fine again.
I did a fresh download and re-flashed the 02 firmware just to make sure that it wasn’t an issue with a bad download or a faulty flash. The problem is consistent and repeatable. I have upgraded and downgraded twice, and the results are exactly the same. My VPN connection works with firmware 01, and it fails with version 02. There is a something different in the 02 firmware that is blocking VPN access.
I recently bought a e4200 v2 and installed connect cloud. I have attached a USB drive to the router. I can connect to it by mapping a network drive on my windows 7 laptop. I can also access it as a media server through my iPad on the local wifi network. This way I can play the music on the USB drive through the iPad. The next thing I would like to accomplish is to be able to listen to the music on the USB drive through the internet (so remotely).
View 2 Replies View RelatedI have broadband internet coming into 1 room of my home. The internet goes through a router I have set up, its a Linksys WRT54G2 (router #1), Firmware version 1.0.04. Everything on this works fine, I'm able to get my TV and laptop in a different room to access the router wirelessly without any inconvenience.In another room I have a regular desktop computer which I would like to get internet on. As well as other devices, so I purchased another router, this time a Linksys E4200 (router #2) in hopes of turning it into an access point.Now I've set up LAN's in the past, using the actual cable plugged into the second router, problem is in this scenario I can't run a cable over to router #2. Both computers use Windows 7. Both router's drivers and firmware have been updated on the Linksys page, all my Windows drivers are updated, etc. I checked other forums for similar questions and although there are some, they date back to 2009 as well as Google which has some websites dating back to 2006! While useful, I wasn't able to find something that details how to solve my problem with my specific setup. I've already gone into router #2 and changed the router's IP to 192.168.1.2 and also turned DHCP off, problem is, once I take that router off into the other room, it doesnt connect to primary network or allow devices to even "see" router #2.
View 2 Replies View RelatedI just bought an E4200 and it was working perfectly, very easy to install, all that it promises. Then I had an energy peak. For some reason, don't ask me why, I did RESET the router not thru the web nor thru Cisco Connect, but pushing the reset button at the back. I can't access the router anymore ! It keeps asking for a password that is never accepted. I have uninstalled cisco connect and tried again. Nothing. The router is not found. Keeps asking for a password. I tried everything: blan+admin, admin+admin, the password I used to have (provided at the cisco connect uninstall).It seems that the RESET never worked. The router is working thru cables, meaning when I can connect to the internet wired. But the router is never found wireless.How could I update the firmware if the router is not recognized (or if I don't have a username+password) ?
View 9 Replies View RelatedI recently bought the E4200 v2. When I first installed, I ran the firmware update and then performed a hard reset (push reset button for 20 secs). I then began to enter all the PPPoE information and network settings into the new router (verified these settings with the existing WRT54GL router I'm current using and they all matched). I then disconnected the old router, and powered up the E4200. I was able to access the new router (192.168.0.1), I could see all previously shared files/computers with the new router, but I could not access most websites - usually I got a timeout error, or they eventually loaded in 10x the usual speed. This was typical of both laptops - one wired, and one wireless. My wireless handheld device could connect to the wireless network, and ran a speeedtest.net test, and upload/download speeds were normal - but I could not access the internet from the device. When I switched back to the old router, everything worked perfectly again. I have tried some suggestions on changing MTU values, but that did not seem to make any difference.
As a work-around, I have ended up keeping the WRT54GL as the main router and using the E4200 in bridged mode for wireless only (not what I ideally would like)..
The Guest Access is a very nice feature for allowing us to provide Internet access in our rental unit.
However, it would be nice to provide the Guests access to the USB printer.
Is there a way to provide access to the USB printer for those who are logged into the "Guest Network"?
Upon attaching my external storage I was able to create a share, copy files and access it successfully from everywhere. Now when I attempt to add an additional share, the router lets me create it but when I try to move access groups over from the available groups, the >> buttons are greyed out. The one working share has the admin and Everyone groups with access. Any additional share I create has the admin group in it by default, but I can't add any more groups. I am logged into the router as admin and logged into the pc as a local admin. I am also unable to change the rights from my pc on a share (access denied). I AM, however, able to map a drive to a new share successfully, but when I copy files over, a few minutes later the filenames are there but they show up as 0 byte files.
View 7 Replies View RelatedI've been on DSL with British Telcom Infnity (FTTC) since March and had no problems with the service. My router, however, an Apple Time Capsule, was not so reliable and needed a reboot every few days,So I just purchased the E4200 V2The Setup completes OK and PPPoE logs into my ISP fine. But then I hit the problem.Most of the websites I use simply won't load . In Safari on my OS X Lion, Macbook, I get an error like this "Request Timeout. The server timed out while waiting for the browser's request. Reference #2.525fdd58.1336048435.0" In IE on my Windows XP laptop, the error is "Internet Explorer cannot display the webpage"But some websites still load fine. So [url]..., loads instantly. Most other sites I try, including [url]... - won't load at all. (Plusnet is my ISP)If I connect to my work VPN, I can browse as normal
View 9 Replies View Related