Linksys Wireless Router :: E4200 - PC Connects To Network But Won't Access Internet?
Sep 26, 2012
I have an E4200, and upgraded to Connect Cloud. It was buggy, and so I downgraded to the firmware before that. I have all the computers working fine in the house except my desktop. it connects fine to the network, can see the other computers on the network, can even do a windows update. But when I go to use google chrome or internet explorer it just wont access the internet. It doesn't seem to work either if it is a wired connection, or a wireless connection It was fine before the upgrade and subsequent downgrade. It was on this desktop that i installed and uninstalled thew Connection cloud. I know enough to set up the network but when it doesn't work
I am experiencing connectivity issues with the wireless part for several weeks. The laptop connects to it, but it shows me that it does not have internet access.I also have a belkin router that I also use. So, when I have the connectivity issues, I connect to the other router. When I use the Cisco Connect application, it goes on for a couple of minutes and then gives the message "If you are not connected to my router SSID name you can't update your router settings".
When starting my laptop it no longer connects to the preferred network. It has been trying to connect to my neighbors unsecured network. I have tried the netsh settings but it searches for another network and will not connect to the one it is supposed to unless I force it to.
can connect to the network but not the internet. In IPCONFIG it says media is disconnected. In properties it says adapter is not connected. But I can see the network, I can ping every computer on the network, just can't get to the internet.Reinstalled all the drivers, tried renew, netsh commands, flushdns, disabled & reenabled. 2 other computers connect to the internet and each other with no problem. Can connect to other WI Fi's too, but still no internet access.
Just set upa new e1200 on my brand new primary PC - connects flawlessly. One other PC in the house and an iphone also connect on the network to the internet with no issues. The problem: My laptop connects to the secure network without prompting for a password,but then does not connect to the internet at all. This same laptop easily connects to the internet via the network as a guest, just as it should. Tried using Easkey, but same result: laptop connects OK to the secure network without a password prompt, but then does not connect to the net.
there has been issues with this router, and I wonder if any of you have issues connecting to the 5ghz when you wake your pc from sleep longer than an hour. For some reason when I put my computer to sleep at night and wake it up in the morning, my computer will not connect to 5ghz. It will work fine with 2.4, both are set in auto, so I dont see any issues. I did try to put 5ghz to a manual setting; wpa2, 40 mhz, and channel 161. I still get the same results. I am doing something wrong or is the router's 5ghz faulty?Also when is the new firmware coming, I am getting sick of my Harddrive being awake 24/7, its killing the harddrives life span and wasting electricity. I should put this in another post, because they should really change the media server to Wild Media Server or Serviio it would be alot better.
I have an E900 I replaced an old Airport Extreme with. The reason was for increased download speed. The Apple router I used saw my work network and I could access files and printers; no changes to my Mac were necessary. It worked out of the box. The new Linksys has Internet connectivity but will not see my work network at all. I have looked into the old settings and cannot figure out how to make the new router see my network. I called Linksys but no dice. What settings need to be changed to see the work network? It is connected to the same ethernet cable as the other router that worked fine.
I have my main router, a E4200v2 which I use as a router and it provides wireless signal throughout my house, however reception is not as strong on the upper floor and there is a slight dead spot, so I purchased an E4200 for the uppermost floor.I set the E4200 to bridge mode so it will act solely as an AP.However connecting the two routers LAN to LAN and the AP does not access the internet.Setting a static IP for the router, instead of acquiring one via DHCP causes me to not be able to access the admin page on the AP.
Connecting WAN on the E4200 to the LAN on the v2 does not work either.My goal here is to have my main router on 192.168.1.1 and the AP on 192.168.1.2 where I can access the admin settings for both routers in case I need to make changes.
I have a Windows 7 computer that was built by ibuypower. It's great, but I ordered a rosewill wireless adapter for it and noticed that my connection strength and speed are both pretty terrible. I went on amazon and bought a TP-Link wireless adapter(TL-WN822N). I installed the most recent "V2" drivers from their website and upon disabling my rosewill adapter and enabling the new TP-Link adapter, I was able to connect to the network, but not access the internet. I have tried power cycling the router, using the reset switch on the router, restarting my computer, and a bunch of commands that I found on this site. Is it possible that I have a defective adapter?
Also, some more information: My isp is comcast and the router is from them as well. Here is my ipconfig /all log for the rosewill adapter(internet access):
Quote:
C:Windowssystem32>ipconfig /all Windows IP Configuration Host Name . . . . . . . . . . . . : Trauma
I cannot get my iPhone 5 to access my wireless network (Linksys E4200) since I reset the router. It asks for the password but doesn't accept it. I'm a newbie so be gentle with me! MSZ
I have a Linksys E4200 router with firmware version 1.0.02. I am using a Macbook Pro. I can connect to a VPN server with the default VPN client software, but it kills my internet connection and disables connecting to SMB
I have been having issues with my home network since upgrading my router from a WRT54GS to an E4200. Prior to this I had no difficulty in accessing my home group or my home network. I have 2 laptops, both are running Windows 7 Ultimate, one is x64 and one is x32.
Laptop 1 (x-64) can access my home network in all its glory ONLY wirelessly...plug in the Ethernet cable and I can't access laptop 2 or my network storage...Laptop 1 is also unable to join my homegroup even after deleting the old one and creating a new one.
Laptop 2 (x-32) can access my home network in most of its glory ONLY wired...unplug the Ethernet cable and I can't access my network storage and it becomes unavailable to Laptop 1 over the network. Laptop 2 is also not able to connect to Laptop 1 even though Laptop 1 can (sometimes) access files from Laptop 2's shared folders.
Also Laptop 2 cannot see a home group created by Laptop 1, but can create a homegroup that Laptop 1 can see but CAN'T join.I have run all the trouble shooters that the system throws at me to no avail, they all say that I have an unknown network error that it can't fix.I do have internet access on both laptops regardless of wired or wireless, and I spent over 2 hours with Cisco "senior" tech support only to be disconnected and realize that they had no clue about this new router..
On E4200 Firmware Version: 1.0.03, I managed to successfully set up "Internet Access Policy" (not the "Parental Controls") to set up the times when internet access is disabled for various IPs on my network.
But I could't setup a policy to block facebook.com. What I am doing wrong? See the attached screen shot. I did click the "Edit List" and apply this polity to the IP Address Range 192.168.1.2 to 192.168.1.254.
I am trying to setup my E4200 to my new Cable Modem. I followed all of the procedures. I get Internet access when plugged directly to modem. I cloned the MAC Address and the Stus of the Router displays my current IP's (so I should have Internet). However, when I plug my computer into the Router I get no internet access.
I have a problem with the e4200 router and a mybook 1 TB connected to it. The media server works fine but after a while i loose contact with the router and the server this means that the Cisco connect doesn't work, the 192.168.1.1 doesn't work and I can't find the disk via \. I do have internet connection via wifi as im using it now....why I loose connection to the router? The lease time is 24h and it can happen more than once in a day.
I have an AT&T Gateway Wireless router to connect to Internet with my wired computer. In another room, I have another wired computer I also use to connect to Internet. I never have problems connecting to Internet from computer that is hooked up to the router, but I often have Internet connection issues from the computer in the other room. It can find the access point, but not connect to Internet. I reinstalled the WUSB300N driver again, but I still cannot connect.
I have a home network with a Linksys E4200 connected to the ISP's fiber box. The problem is that when I'm connected to the Linksys, either wired or wireless, the connection to the internet will drop after what seems to be a random amount of time (normally anywhere from 2-10 minutes). I can restore the connection by doing any of these things:-reboot Linksys-disconnect and reconnect cable from router to fiber box-if on wireless connection, make changes to the router wifi settings, like change the wifi channel.The internal network stays up, and I can ping both the internal and external ip of the router, but not the fiber box. I have also had the same behavior with an Edimax Wifi AP and less frequently with a Edimax router (once every 1-2 days). I have done everything I can think of:-changed the wifi channels-changed the ip ranges, subnets, turned router DHCP off and back on-booted the fiber box-changed cables-updated all routers to the latest firmware, the network cards with latest drivers...and loads other things that I don't remember right now. For the wifi side of things, there are no other networks in range that could interfere. The same problem occurs on both my and wife's Win 7 laptops and on the iMac (latest OSX). Here's a fun detail: while the Linksys has lost its connection to the internet, I can still access the internet through the old Edimax router connected to the same fiber box, either wired or wireless.
After a couple of hours using the internet, the connection stopped. The wireless router still had an 'Excellent' signal, but it also said I had no internet access. All of the other wireless devices in my house connect to the internet perfectly, including when right next to the laptop.I've tried disabling the firewall and resetting the computer a few times, but nothing seems to pick up the internet access. The troubleshooting guide tells me that it is a problem with the wireless modem, but quite obviously that isn't true.
I have configured my e4200 to block traffic at certian times uses both the Parental Controls and the Intenet Access Polices. Neither one seems to work though. [code] I have the same MAC addresses specified in each rule. Initally I had only the first two rules. Those didn't work, so I added rule 3 and 4 (they do the same thing as rules 1 and 2 but from the opposite direction). There are no compliaints, but they don't stop any traffic.
I started with the Parental Controls, they didn't work either. The page in there that lets you pick which machines you want to block seemed next to worthless. I have about four rows listed as "Network Device." REALLY LAME! As the MAC addresses are accesible and these weren't working I went to the IAP.
Have two other computers that connect with ease to the Netgear wireless router, but the new computer will not access the internet. I have been searching for answers and have tried about everything I can find nuder similar posts, but I still have not internet access. At varying times, I have had "internet access", but no actual ability to load websites. Right now, I do not even have access. I am at a loss.Even at my low level of experience, I am usually able to tinker until I fix the problem, but I am about four hours in and currently seem to have taken a step backward. I cannot even begin to explain what things I have already tried
I am running a VPN server on my desktop at home, with all the default settings, and i checked the box that allows clients to connect over the internet. this is win7 x64 computer. I opened up port 1723 with PPTP protocol on my E4200 router.On the client i am running win7 x64 as well. I am able to connect to the vpn, from another internet connection, but there is no local network acess. It says the status is No Internet Access. and the IP that is assigned is the 169.x.x.x one that windows defaults when it doesnt find a dhcp server.How can i get the client to connect with full local network access. Right now being connected to the vpn, it means nothing, i have no access other than being "connected".
It is a Satelite 733. Have pinged without any response however the wifi or hardwire will show connected to the local net.I have four other units surfing the web fine and wifi picks up ok except for one unit that my neighbor need will not connect no matter what. Have updated all the drivers, uninstalled and re-installed devices, reset ip, dumped the dns several times, etc.So here is the ipconfig stuff....ignore the cable connect I only have the wifi on at the moment. I have stared at this to the point where I know naathing .Is the tunnel adaptor the indication that the card is out? Oh and I tried taking out IPV 4 on both channels and nothing so I left one with 4 on and the other with it off just as something else to try. [code]
Laptop connects to wifi network. But it shows "No Internet Access" message.My Macbook connects to the internet just fine and the wifi on my iphone works as well.The ethernet on the laptop works and I am able to access the internet this way. The laptop does connect to some of the other access points but I've had issues with my router.I tried the usual debugging mechanisms - disable/enable adapter, reset the router, reset the tcp/ip stack. [code]
I have a compaq preario running on windows 7 ultimate.It has been working well with the internet connection but recently it stopped connecting to the internet.It recognizes other computers in the network but the internet connection is not available.
My sis has a toshiba satellite laptop running vista and she cant go on the internet while mine and my dad's can.Her computer was able to go on the internet but then suddenly she cant. I've searched everywhere, i tried resetting the TCP/IP, setting a static IP address, even returned the laptop to factory settings, but no luck.The network page stays as: Computer----------unidentified network-------x------internet[CODE]
I was installing a software on my other laptop (it had SQL software with it) and I ran into some trouble as I got error problems that the installation of the software had failed and now whatever I do, I can't access the web! Sure enough, my wireless connection connects successfully and it indicates that I am on the "Internet" but every time I try to use either firefox or internet explorer to go to a web site, it says I don't have a connection. It is extremely odd and I don't know what it might be
I've been trying to get FTP Running up on my router for some time now.
I know my current WAN address and have setup a specified folder on my E4200 for the FTP partition. A username for myself has been created with login info and I have forwarded the port I have specified on my router's FTP configuration page.
I try to log into the server, but whenever I try to log into it, I keep getting a "incorrect login information" message back at me.
If I cancel out of that then I get an error message saying it can't find the specified folder and to check the address of the server.
I know the login information information is correct and I've tried changing the password to others of varying lengths.
I've also tried changing the port I'm running the FTP off of incase my ISP has blocked that port, nothing works.
i have installed lutron lighting in my home and need to configure e4200 so i can access it from outside home with iphone application. Lutron manual says to go to VPN iphone setting and add PPTP connection, server, account and password. I need to do same on e4200 but not sure where to go create pptp connection, accounts and passwords?
I have a Free Community WiFi that I can access from the edges of my house, but not from anywhere inside the house. My personal Internet connection is out due to the fact our bill trippled for some reason we can't figure out 2 months ago without telling us. We've had an auto payment sent every month for just over what it should be. So until I get this sorted out with the ISP I have to use the community WiFi. I would like to be able to use the internet from somewhere other than the wall in my kitchen.
So, I have a number of Routers, 2 Actiontec Q1000s, but only 1 power suply, a D-Link WBR-2310, D-Link DIR-601 & a few other ods & Ends including a 12DB Amped Wireless & An 8DB Hawking Tech antennas.What I want to do is to use 1 router to connect to the CommunityShared Network, A wired connection to another router (Preferably the Q1000 as it's already setup for my Home Network) & that router to serve my Home Network, preferably over the WAN port if possible, but I can run VPNs on each device for a week if I have to.
Right now I have one computer setup in the kitchen with a High Gain Antenna conected to a Atheros SUB-362 EXT USB WiFi card, (This computer gets 7Mbps Down & 9Mbps Up) then the built-in WiFi card connected to my Home network with a Static IP, The Q1000 set to use that IP as the Gateway. I can get about 200Kbps max on devices connected to the Home Network. But the biggest problem is that my old Atheros card disconnects randomly when accessed from one of the devices on the home network. I'm fine with a ThirdParty Firmware Update on the D-Links if necessary.When I look online I only find posts about how to extend a network using a second router or how to use a specific router to repeat or bridge.
Just got a new hard drive installed on my laptop, and now for some reason I can not access my router. I am connected to the internet, and everything is fine there, but when I type the 192.168.1.1 and enter admin as the password, it shows that I am unauthorized.
