I have an E4200 v1 wireless router, F/W 1.0.04.
Article ID 4041 [URL] says I can have up to 10 Internet Access Policies but the web based GUI has a pull down with only 5 possible.
Is 10 policies possible? If so, how?
I don't know how many of you read the article List of tested USB storage devices for the Linksys E4200 before buying it. Basically, what it says, is that you cannot connect your "too old" or "too new" (>2TB) HDD to this router and you have to settle with an WD MyBook Mirror Edition 2TB or Seagate FreeAgent Desk 2TB at best. Needless to say that this not good enough. First I believed that the list is incomplete and if a brand is listed with a model then a bigger or a smaller one will work as well. Sadly this is not the case: neither WD Passport with 320 GB (FAT32) nor a LACIE 1TB (NTFS) could be connected to E4200.
If any of you succeeded to pair the router with a different external HDD than the ones from the.
P.S.: I strongly believe that Cisco should work on an updated firmware which should expand the list of supported HDDs.
Just purchased the E4200 for our office to find that the most current mac operating system, is not supported by this wireless router.
View 1 Replies View RelatedI'm trying to connect an Epson Stylus Color 740 USB printer to a newly purchased E4200 wireless router. I've upgraded to the latest Cisco Connect software and to version 1.0.0.3 router firmware. I get the message "A non-supported device is connected to your router's USB port. Disconnect that device and follow the steps below to connect a USB printer to your router." Cisco support was not beneficial.
View 1 Replies View RelatedIn January 2012 I bought a Linksys E4200v2. I am trying to download a firmware version upgrade and it wants to know what hardware version I have. The top of my router (where the model number is displayed), only has E4200. I have looked through my receipts, the box it came in, and anything else I can find to do with the router - they all have the E4200v2. In case the 'v2' portion is for the hardware version, I do not want to download the wrong firmware version and end up with a router that doesn't work
View 4 Replies View RelatedI have my main router, a E4200v2 which I use as a router and it provides wireless signal throughout my house, however reception is not as strong on the upper floor and there is a slight dead spot, so I purchased an E4200 for the uppermost floor.I set the E4200 to bridge mode so it will act solely as an AP.However connecting the two routers LAN to LAN and the AP does not access the internet.Setting a static IP for the router, instead of acquiring one via DHCP causes me to not be able to access the admin page on the AP.
Connecting WAN on the E4200 to the LAN on the v2 does not work either.My goal here is to have my main router on 192.168.1.1 and the AP on 192.168.1.2 where I can access the admin settings for both routers in case I need to make changes.
I have a Linksys E4200 router with firmware version 1.0.02. I am using a Macbook Pro. I can connect to a VPN server with the default VPN client software, but it kills my internet connection and disables connecting to SMB
View 5 Replies View RelatedI have an E4200, and upgraded to Connect Cloud. It was buggy, and so I downgraded to the firmware before that. I have all the computers working fine in the house except my desktop. it connects fine to the network, can see the other computers on the network, can even do a windows update. But when I go to use google chrome or internet explorer it just wont access the internet. It doesn't seem to work either if it is a wired connection, or a wireless connection It was fine before the upgrade and subsequent downgrade. It was on this desktop that i installed and uninstalled thew Connection cloud. I know enough to set up the network but when it doesn't work
View 4 Replies View RelatedI'm just about to trade-in an E4200v2 for a E4200v1, primarily to regain the "Internet Access Policy" capability.
Just wanted to do a reality check with those of you who tried/use IAP... does it work basically as advertised?
I would be using IAP to specify MAC addr's of devices, blocking them from certain URL's and limiting their hours of Internet access.
And I plan to have Linksys's DHCP Server turned OFF, since my Windows Server handles DHCP on my network.
Should I expect all of this to work OK? No major reliability problems with IAP?
On E4200 Firmware Version: 1.0.03, I managed to successfully set up "Internet Access Policy" (not the "Parental Controls") to set up the times when internet access is disabled for various IPs on my network.
But I could't setup a policy to block facebook.com. What I am doing wrong? See the attached screen shot. I did click the "Edit List" and apply this polity to the IP Address Range 192.168.1.2 to 192.168.1.254.
I am experiencing connectivity issues with the wireless part for several weeks. The laptop connects to it, but it shows me that it does not have internet access.I also have a belkin router that I also use. So, when I have the connectivity issues, I connect to the other router. When I use the Cisco Connect application, it goes on for a couple of minutes and then gives the message "If you are not connected to my router SSID name you can't update your router settings".
View 1 Replies View RelatedI am trying to setup my E4200 to my new Cable Modem. I followed all of the procedures. I get Internet access when plugged directly to modem. I cloned the MAC Address and the Stus of the Router displays my current IP's (so I should have Internet). However, when I plug my computer into the Router I get no internet access.
View 3 Replies View RelatedI have a problem with the e4200 router and a mybook 1 TB connected to it. The media server works fine but after a while i loose contact with the router and the server this means that the Cisco connect doesn't work, the 192.168.1.1 doesn't work and I can't find the disk via \. I do have internet connection via wifi as im using it now....why I loose connection to the router? The lease time is 24h and it can happen more than once in a day.
View 4 Replies View RelatedWhich transmit hash policies are supported by the SLM2008? I can't find this information in any of the documentation for this switch, all that is stated is that it supports Link Aggregation using IEEE 802.3ad LACP. I'm connecting to a Netgear ReadyNAS Pro that supports Layer 2 and Layer 3+4 transmit hash policies and I'm not sure which to choose (or whether it matters).
View 2 Replies View RelatedWhat is the max number of policies can ASA 5525X supports ? I dont find it in the datasheet.
View 5 Replies View RelatedI have configured my e4200 to block traffic at certian times uses both the Parental Controls and the Intenet Access Polices. Neither one seems to work though. [code] I have the same MAC addresses specified in each rule. Initally I had only the first two rules. Those didn't work, so I added rule 3 and 4 (they do the same thing as rules 1 and 2 but from the opposite direction). There are no compliaints, but they don't stop any traffic.
I started with the Parental Controls, they didn't work either. The page in there that lets you pick which machines you want to block seemed next to worthless. I have about four rows listed as "Network Device." REALLY LAME! As the MAC addresses are accesible and these weren't working I went to the IAP.
After updating the firmware of my WRVS4400N from V 2.0.1.3 to 2.0.2.1 all traffic was blocked for all machines, even some not included in the list of PCs. As the log was showing that all traffic was blocked by access policies, I disabled the only rule I had (blocking access to some sites to some MAC address list) and everything worked fine.I tried creating a new, simpler rule but after activation it blocked again all traffic for all the LAN.After many trials, I decided to roll back to the previous V2.0.1.3 which solved this problem.
View 1 Replies View RelatedI'm trying to set up a S2S VPN between two ASA5505 SP units running ASA Version 8.2(1). I've ordered additional ADSL2 lines to handle this traffic and I'm having troubles with the configuration for the additional PPPoE connection. Here is are extracts from my current config; First the interface vlans
!
interface Vlan1
nameif inside
security-level 100
ip address 192.168.1.1 255.255.255.0
[code]....
The result being that I can ping the OUTSIDE interface, but get no reply from the VPN interface. I've checked ADSL lines, they are up. The two PPPoE sessions are logged in and active. I can even see the ICMP packets hit the VPN interface, but there is no reply.
determine whether I have QoS properly setup on my router, and why the rules do not appear to be taking effect.ISSUE We have a couple of laptops, smartphones, and a Wii on our home network. One device, my roommate's laptop, is a real bandwidth hog. It's connected (via internet, not VPN) to a work server and is frequently downloading and syncing large datafiles and media files.Unfortunately, when that laptop is downloading the other devices either cannot connect to the internet without timing out, or is VERY slow, for example pulling up websites like google.com. When that laptop is offline, everything works fine. It seemed like enabling QoS would resolve our problem.\
SETUPLinksys E1000, latest firmware (v2.1.02), using WPA2-Personal security.
We first tried enabling QoS and setting the MAC address of the downloading laptop to "low" priority and all others to "medium". No luck - the downloading laptop still seems to be hoarding the bandwidth.We also tried adding the download application to the list and setting the port to "low". Still no luck.We added a new application called "web" and set port 80-81 to "high", but that didn't work.We then disabled WMM support. No dice. The other devices still can't connect while my roommatte's laptop is syncing.We've fiddled around with the settings a bit, but no matter what, it looks like the QoS rules are not being applied.And is it acceptable to have multiple categories (MAC and application) in the QoS rules?
I've been trying to get FTP Running up on my router for some time now.
I know my current WAN address and have setup a specified folder on my E4200 for the FTP partition. A username for myself has been created with login info and I have forwarded the port I have specified on my router's FTP configuration page.
I try to log into the server, but whenever I try to log into it, I keep getting a "incorrect login information" message back at me.
If I cancel out of that then I get an error message saying it can't find the specified folder and to check the address of the server.
I know the login information information is correct and I've tried changing the password to others of varying lengths.
I've also tried changing the port I'm running the FTP off of incase my ISP has blocked that port, nothing works.
i have installed lutron lighting in my home and need to configure e4200 so i can access it from outside home with iphone application. Lutron manual says to go to VPN iphone setting and add PPTP connection, server, account and password. I need to do same on e4200 but not sure where to go create pptp connection, accounts and passwords?
View 4 Replies View RelatedJust got a new hard drive installed on my laptop, and now for some reason I can not access my router. I am connected to the internet, and everything is fine there, but when I type the 192.168.1.1 and enter admin as the password, it shows that I am unauthorized.
I have a Linksys E4200 router
I posted before about my problem in forwarding certain ports in a LAN-to-WAN cascaded router setup, and I finally gave up looking for a solution, and went for a LAN-to-LAN. On the internet there is many articles to be found on how to accomplish the setup, but none of them is complete, and as such, I think I really screwed up someplace. My setup: ISP modem/router (192.168.1.1 / 255.255.255.0) DHCP enabled, and DHCP address range 3-100 NAT configured Static IP address for a Synology NAS connected to the E4200 SSID id_1
Then the E4200 Internet connection type: I set to Static IP IP 192.168.1.2 Subnet mask 255.255.255.0 Default gateway: 0.0.0.0 (to disable the WAN)
Then, the network setup: Router IP: 192.168.1.2 gave me the error that WAN and LAN IPs were identical. I played around quite some time but always got an “illegal value” error. Then finally I put the IP to 192.168.0.1 (IP I had in LAN-to-WAN) and this was accepted. And subnet mask: 255.255.255.0 The SSID I left unchanged from what it was, id_2 (also gives me the advantage that I know to which router I am connected)
I rebooted the E4200, and I was connected. But … I am unable to connect to the E4200 configuration page, and even Cisco Connect cannot establish the connection.
I recently put in a surveillance system with remote access. I have an application on my android phone and it can be viewed by any browser. While I am connected to my network these functions work fine, on my phone and any desktop/laptop. The problem happens when I try to view remotely, off my network. I had this setup on my Netgear router before I got my new fancy schmancy Cicso router becaue the netgear wasn't cutting the cheese in keeping my wireless connectionstory.So here is what I got. I need 3 ports forwarded for this work, and how I got it work on my Netgear. I have these 3 ports forwarded as single ports. I have them forwarded in a range and I have port triggering turned on. No matter what or which combination of these few things I try, I can't access the DVR remotely, again unless I'm local to MY network.Some additional notes - the DVR has a static address and that address has been reserved in the DHCP settings of the router.
View 5 Replies View RelatedI have a problem te access e4200 with web access on a iMac with Lion 10.7. I try to connect with standard Safari.With 192.168.1.1. it won't open, if I look voor IP address it should be 192.168.0.1. now the login screen opens but now I can't login with clean name en password "admin" it gives an error.I also can't install Ciso Connect from CD, it gives a error not right version!.Is there anyone that use iMac with E4200 and Sonos zone player?
View 3 Replies View RelatedThis is a feature that I have researched for by looking at ISRs G2 data sheets and cisco.com website.The number of users that can be supported or the recommended number of users per router chassis/model is not mentioned anywhere.However this is mentioned in the Cisco 880 ISR data sheet. What are the number of users that can be supported or the recommended number of users on Cisco 1900/2900/3900 ISRs?
View 4 Replies View Relatedhow to setup the E4200 so that I can access the media server when I am in office? I was browsing on the Cisco website and unable to find it.
View 8 Replies View RelatedIf you have MAC filter enabled with the E4200 Firmware Version: 1.0.01 you cannot connect to guest.
View 2 Replies View Relatedi enable guest access, when connecting though any device it doesn't ask for password but allows access straight away. I've tried changing the password, but no luck.
View 3 Replies View RelatedI've got an E4200 at my house. I'd like to know if it's possible for my to establish a VPN connection from a remote location to login to my E4200 to get access to my computers behind the firewall.
View 1 Replies View RelatedI cannot connect to my company’s VPN after installing the current firmware (FW_E4200_1.0.02.013_US_20110524) on my E4200 router. Version 1.0.01 was on the router when I received it, and it worked without issues. As soon as I upgraded version 02, I could not initialize a VPN connection. When I try to start a VPN session, I get a "page not found" error when attempting to initiate SSL VPN service using a Microsoft Forefront Unified Access Gateway. VPN pass through is enabled for all protocols in the e4200’s setup. As soon as I revert to firmware 01, everything works fine again.
I did a fresh download and re-flashed the 02 firmware just to make sure that it wasn’t an issue with a bad download or a faulty flash. The problem is consistent and repeatable. I have upgraded and downgraded twice, and the results are exactly the same. My VPN connection works with firmware 01, and it fails with version 02. There is a something different in the 02 firmware that is blocking VPN access.
I recently bought a e4200 v2 and installed connect cloud. I have attached a USB drive to the router. I can connect to it by mapping a network drive on my windows 7 laptop. I can also access it as a media server through my iPad on the local wifi network. This way I can play the music on the USB drive through the iPad. The next thing I would like to accomplish is to be able to listen to the music on the USB drive through the internet (so remotely).
View 2 Replies View RelatedI have broadband internet coming into 1 room of my home. The internet goes through a router I have set up, its a Linksys WRT54G2 (router #1), Firmware version 1.0.04. Everything on this works fine, I'm able to get my TV and laptop in a different room to access the router wirelessly without any inconvenience.In another room I have a regular desktop computer which I would like to get internet on. As well as other devices, so I purchased another router, this time a Linksys E4200 (router #2) in hopes of turning it into an access point.Now I've set up LAN's in the past, using the actual cable plugged into the second router, problem is in this scenario I can't run a cable over to router #2. Both computers use Windows 7. Both router's drivers and firmware have been updated on the Linksys page, all my Windows drivers are updated, etc. I checked other forums for similar questions and although there are some, they date back to 2009 as well as Google which has some websites dating back to 2006! While useful, I wasn't able to find something that details how to solve my problem with my specific setup. I've already gone into router #2 and changed the router's IP to 192.168.1.2 and also turned DHCP off, problem is, once I take that router off into the other room, it doesnt connect to primary network or allow devices to even "see" router #2.
View 2 Replies View Related