Both the iPod and iPhone were on the network and working and now neither is on and don't detect the network at all. Have turned off and on both devices as well as the router to no avail. My mini Mac is up and running and has been all day.
View 1 RepliesI cannot get my iPhone 5 to access my wireless network (Linksys E4200) since I reset the router. It asks for the password but doesn't accept it. I'm a newbie so be gentle with me! MSZ
View 2 Replies View RelatedI have an E4200 functioning with a new Comcast/XFinity cable modem on the public IP (Internet) port. That modem provides a DHCP address to the router (currently 50.129.x.x./255.255.254.0) The problem is that this new setup is leaking COMCAST DHCP responses through the E4200 to my WiFi clients. Most of the clients (newer iPODs, laptops) are smart enough to behave correctly and use Wifi Protected Setup. This problem means that one older iPOD seems to be receiving the Comcast DHCP (as 192.168.33.0/24 range) instead of E4200 Wifi DHCP range (as 192.168.1.0/24 range). I imagine the most direct solution is to pull the public connection briefly and allow the iPOD to fetch a valid WiFi DHCP from the remaining DHCP server on board the E4200. HOWEVER, I'd like to configure the router to suppress all DHCP packets from the Comcast network - or otherwise make sure the WiFi clients only receive DHCP from the router and not the Comcast modem.
View 4 Replies View RelatedI have installed Ver.1.0.03 (Build 14) Firmware on my E4200 I launch cisco and detct the printer fine prints fine but goes to offline and my scaner in that printer not work My printer is cx7400.
View 1 Replies View RelatedI have a Wag 160n router which works fine with desktop pc connected by ethernet & wirelessly to laptop. My nokia phone finds the wi-fi signal but apple i-phone & ipad dont!
View 0 Replies View RelatedI just updated to the new firmware 1.0.02 and the USB stop working for my External Hard WD 500GB harddrive. I had to roll back to firmware 1.0.01 for it work
View 2 Replies View RelatedFirmware is 1.0.05 (didn't work on 1.0.04 too). It has a single partition formated as ntfs, any hint why it doesn't work or diagnostic I could do?
View 2 Replies View RelatedI recently purchased an E4200, but I am experiencing slow/inconsistent performance and connection problems with iPhone 3G, 3GS and 4. The iPhones are running the latest firmware 4.3. The E4200 has also been updated to the latest firmware 1.0.01 build 10. I do not experience these problems with various laptops, and I did not experience them with a previous Cisco router WRT610N, nor with a D-link DIR825 in another location. The security is set to WPA2 Personal and all the other settings are the same from the prior router. If I disable the security, I do not experience the connection problems, but still experience the slow performance. If I switch back to the WRT610N, I do not experience any problems. this a E4200 firmware issue yet to be resolved?
View 9 Replies View RelatedI have a E4200 fw 1.0.03 my pc, laptop connect to E4200 is OK but have a problem with my iphone 3Gs iPhone 3Gs connect to E4200 at day is OK althought sometime loss packet but at night (after 17:30) iPhone can't connect to E4200, althought I don't config anything.This is my E4200 configure fw: 1.0.03 No set schedule access internet
At Day This is a log DHCP when iPhone(MAC: 00:26:bb:fb:29:a0) connect to e4200 at Day Sun, 04 Dec 2011 07:11:00 received REQUEST from 00:26:bb:fb:29:a0 Sun, 04 Dec 2011 07:11:00 sending ACK to 192.168.1.136 get IP very fast ping packets at day (loss some packets):
But at Night everything change althought I don't config anything on e4200This is a log DHCP when iPhone(MAC: 00:26:bb:fb:29:a0) connect to e4200 at Night Sat, 03 Dec 2011 22:11:20 received REQUEST from 00:26:bb:fb:29:a0 Sat, 03 Dec 2011 22:11:22 received REQUEST from 00:26:bb:fb:29:a0 Sat, 03 Dec 2011 22:11:27 received DISCOVER from 00:26:bb:fb:29:a0 Sat, 03 Dec 2011 22:11:28 sending OFFER to 255.255.255.255 with 192.168.1.135 Sat, 03 Dec 2011 22:11:28 received DISCOVER from 00:26:bb:fb:29:a0 Sat, 03 Dec 2011 22:11:28 sending OFFER to 255.255.255.255 with 192.168.1.135 Sat, 03 Dec 2011 22:11:31 received REQUEST from 00:26:bb:fb:29:a0 Sat, 03 Dec 2011 22:11:31 sending ACK to 192.168.1.135 Sat, 03 Dec 2011 22:11:32 received REQUEST from 00:26:bb:fb:29:a0 Sat, 03 Dec 2011 22:11:32 sending ACK to 192.168.1.135 Sat, 03 Dec 2011 22:11:34 received REQUEST from 00:26:bb:fb:29:a0 Sat, 03 Dec 2011 22:11:34 sending ACK to 192.168.1.135
Very difficult to get IP from e4200 at night, sometimes getting IP but not on the Internet, sometimes can not get IP and iPhone get message "unable to join the network "ciscoTNTn""ping packets at night (can't ping):
While iPhone is connected to the Draytek Vigor2600VG good no matter day or night.I re-upgrade fw 1.0.03 and restore factory defaults but still not fixed.Is that a bugs ?
all other devices have excelent signal
View 5 Replies View RelatedI have Linksys configured with IP 192.168.0.x and my local network ip 192.168.1.x have firewall connected to Adtrans box that gives us internet access via T1 line and other port is connected to the switch. Wireless router is connected to the switch using internet port.I can connect to wireless using iphone but emails don't work when connected to wireless. I tried to connect laptop to wireless is does not connect.
View 9 Replies View RelatedI have several WAP2000 (Firmware 2.0.0.5), and while they work fine for PC's, iPhones, iPod touches cannot connect to them.Well, they connect briefly, get an IP address from the router, and immediately drop the connection to re-connect again.I have tried changing channels, eliminating all but one of the AP's, and so forth. Any issues with this firmware? I see posts where people are saying their iPhones connect up fine. This happens on versions 3.x and 4.x of the iphone O.S. It's not limited to one iphone or ipod touch; we've tried several.
View 12 Replies View RelatedWe have a centralized WLC with some branch office with AP's in Flexconnect Mode. The Wlans are configured to use Web Authentication (Landing Page). The Landing Page is Cisco Default.
We're experiencing some problem with Apple Devices, on some the Landing Page apperars on some not. The WLC Software is about 1 year old. On a XP machine the landing page doesn't appear too, but you can type in the address manually and it works.
Whats the best solution to include the Apple Devices successfully in the WLC Wireless World.
I'm having problems getting the WUSB54G v2 adapter work with the WRT160N router (firmware 2.0.03). I'm running Vista Home Premium SP1. My wireless network is not detected by the WUSB54G and is not on the list of wireless networks I can connect to. I'm also having trouble connecting to WUSB54GP ver 4. The network is detected, but I can't connect.
Change the Beacon Interval to 75
Change the Fragmentation Threshold to 2304
Change the RTS Threshold to 2307
Now the WUSB54GP ver 4. is working perfectly, but the WUSB54G v2 still can't detect the network. I'm also running a PS3 and a laptop, which work perfectly with the WRT160N router.Also, the WUSB54G v2 system works just fine with my old router (WRTP54G).
just brought this router model #wrt120n and can't get setup disk to install because it says i have no ethernet port
View 1 Replies View Relatedi have my E1000 network detected by laptop and devices but can't connect to Internet. The E1000 is connected to Cisco 2100 modem and I can connect to Internet if I plug my laptop/PC directly to Cisco 2100 modem.
View 2 Replies View RelatedI had PCs, Macs and other devices (iphone, itouch) able to connect fine to the WRT610n. I moved to an apartment and when I turned the network on all the devices could connect expect for the iphone and itouch. I have tried turning the wireless security off and MAC filtering off . I get the same "Unable to join the network" message.
View 7 Replies View RelatedI have a Linksys WRT120N which had suddenly and unexectedly stopped working after disconnecting my roku box. I didnt worry about it until I got an Iphone and now .I was able to re-establish the wireless connection on my netbook today after a ton of research and messing around with the settings and then downloaded network magic, which finally fixed the problem. I believe that it automatically transmitted the WEP key to the Netbook, which is what I am missing when I try to log into the network on the Iphone.How do I get this password to show up on Network Magic? When I look at the settings, it does not show the actual numbers, they are hidden.
View 6 Replies View RelatedSet up our E3000 following the set-up guide. However, wireless devices (laptop, iPhone) recognize the network, but cannot connect. There's no prompt for a password or anything.
View 6 Replies View RelatedMy EA4500 router seems to drop mine and my wife's iPhone wifi connection at what appears to be the edge of my router's range. When we come back in range, our iPhone's intermittently give the error "Unable to join network.". And we're stuck in that mode. When I check the Devices menu in the CCC interface, I notice the iPhone device is configured and still online. However the "x" box to delete the device is greyed out because it's online. So how do I get out of this state and have my iPhone connect
View 2 Replies View Relatedi have a LINKSYS WRT54G router .. i bought an apple ipod touch recently and i am unable to connect it to my wifi network. My ipod detects the wifi network but when i select it , it asks for password. now i dont know which password is this bcoz everytime i poer on my computer or laptop i never type a password b4 accessing internet.. it is auto connected. i know the admin password for my router but that is denied by ipod to connect to internet. Is there any other password we have to give for connecting deveices through LINKSYS or some changes i need to do in my connection ?
View 2 Replies View RelatedIPOD Touch 4G that will not connect to internet. it sees the network, requests a password but will not connect. Have been entering the same 8 character password the router uses.
View 5 Replies View RelatedI have a WRT5G2 V1 wireless router. I cannot connect to the internet with my kindle,I-pod and Wii. I had this problem a few years ago when I bought this device for my laptop.
View 7 Replies View RelatedI have NM 5.5.9195.0 and WRT120N Linksys router. I have an Ipod using WIFI to connect to the network which I would like to restrict times for. Using the access restriction page in the manage/setup of the router seems to not work well. The system does recognize the MAC address of the Ipod but setting times to allow or deny gives me odd results. The allow button actually denies use for one thing. Secondly, the deny time ends, but the Ipod still cannot connect sometimes. It is like the system gets stuck in deny. I have tested using a random 5 minute deny time period, yet the Ipod is denied all times. The system is consistent in denying the Ipod (actually using the allow button) but not on the times.
View 4 Replies View Relatedafter i had to replace my old router from lynksis for the wrt110, everything works except for the ipod touch and the ipad. what could be the issue?
View 8 Replies View Relatedhaving wireless G network coexist with Wireless N network on e4200.
I have an existing wireless G network with ActionTec router for VERIZON FIOS. I just added the E4200 router for wireless N. I have latest firmware, 1.0.03. Version 1 hardware.
We are getting a couple of laptops for holidays and would like these to be able use wireless N. I have older laptop/itouch/roku device that use wireless G/B network from ActionTec router. I would like to keep the ActionTec router for wireless G/B, so that both 2.4 and 5.0 ghz networks are Wireless N only.
I have both routers configured so that ActionTec is primary with DHCP and the e4200 is secondary, setup in bridge mode, with DHCP off and static ip of 192.168.1.2. Used this for guidance -> [URL]
I have one SID for ActionTec Wireless G network and this is set for Channel 1
I have a different SID for e4200 Wireless N network, same for 2.4 and 5.0 and I left defaults on other wireless settings.
I have the wireless guest network up and running just fine. But, I need to also connect to the router's quest network via one of the ethernet ports. Can I just give the LAN-conencted PC a 192.168.3.x static IP to access the guest network? I am assuming there is no VLAN functionality...
And even better, can I set up a DHCP relationship to that port? So that any device plugged into the port will get a IP on that subnet?
I have e4200 router set up with different SSIDs for 2.4ghz and 5ghz. My laptop (Lenovo x220 with Intel 6205 wireless adapter) can't see the 5ghz network. I've tried changing the channel for the 5ghz network and it didn't fix the problem.
View 9 Replies View RelatedEver since I bought the E4200 months ago I had no wireless network between my laptops. pc's devices. I discovered now that I do have network (everything cool) when I disable NAT. That is all nice, but I don't have internet then.
View 8 Replies View RelatedI cannot get the Guest Network feature to work.Even though Guest SSID is enabled, it does not show up on any devices attempting to connect. Manually connecting by entering the Guest SSID fails (not recognized). On devices with the primary 5 and 2.4 GHz configured they do see the third network but without SSID (unknown) and are also unable to connect to it manually using the SSID.I did not try this before 1.0.02. Have rebooted modem and verified all configs (multiple times). The network is live in an office and can't keep screwing with it or drastically changing its settings.
View 9 Replies View Relatedmy general internet connectivity with my e4200.I have a new but similar problem today with the same router.After powering down equipment and moving it around, my wired connections all error. Error in that they will not get an IP address nor will they connect to the internet or each other.My wireless connections still work flawlessly.
I tried powering down the devices over night (to avoid any heating issues) and then powering up but the results are the same. I am obviously missing something, and don't really want to start my network from scratch again...
I'm trying to block two URL's over the entire network via my E4200. I'm having a heck of a time doing this, I loginto my router via the browser (the web setup) (because I think Cisco Connect on the Mac is about the worst software ever written.) And I go to the Access Restrictions page. There I understand I'll have to use the Internet Access Policy pane to make some more advanced settings than the Parental Control.
I enter a name for my rule, so far so good. Enable it. Go to the applied PC page. Open the page to enter MAC adresses and IP's. I go to the IP Address Range field and entere in the box numbered 01; 192.168.2.2 to 192.168.2.51 which in my case is the enitre network. Save the setttings and close that window.
I don't set Access Restriction to deny becasue that seems to block the entire network.
So I go the the Website Blocking by URL Address option and enter the URL I want to block.
I don't do anything wiht the the Blocked Applications since I don't want to block a specific service or application. So I click Save Settings.
And yet when I go to the URL I want to block it doesn't work! [URL]
I've been playing around with my E4200 but cannot find the right combination of settings. My problem: I bought the router for cable internet that never happened. In the meantime I am accessing the web using a 3G dongle. Hoewever, while connected to the router (wired or wireless), all the PC's in my home refuses to access the 3G internet - it is as if it wants to use the E4200 to access the net, no matter what. So every time I want to access the internet, I have to disconnect the PC from the home network, and connect with the 3G on that particulat PC. (I have three PC's at home, 1 wired and two wireless). If I set the E4200 to bridge mode, I struggle to find a logical IP address, since I would ideally like to run the network at 192.168.1.X. How do I set the E4200 to allow a home network to be established without having to disconnect everytime I use the 3G on a PC? Also, it seems that if the router doesn't handle the DHCP duties, win7 by default makes the network public, which complicates sharing a lot...
View 5 Replies View Related