I have installed Ver.1.0.03 (Build 14) Firmware on my E4200 I launch cisco and detct the printer fine prints fine but goes to offline and my scaner in that printer not work My printer is cx7400.
View 1 RepliesModel name: Linksys E4200
Model number: E4200
Firmware version: 2.0.36.126507
Operating system: Windows XP SP 3
Software version: 1.4.12005.2
Connection type (WAN): DHCP
My Canon MX882 multifunction printer is connected to the router via USB cable. The printer works. The scanner does not work.
I just updated to the new firmware 1.0.02 and the USB stop working for my External Hard WD 500GB harddrive. I had to roll back to firmware 1.0.01 for it work
View 2 Replies View RelatedFirmware is 1.0.05 (didn't work on 1.0.04 too). It has a single partition formated as ntfs, any hint why it doesn't work or diagnostic I could do?
View 2 Replies View RelatedBoth the iPod and iPhone were on the network and working and now neither is on and don't detect the network at all. Have turned off and on both devices as well as the router to no avail. My mini Mac is up and running and has been all day.
View 1 Replies View RelatedI have a multifunctional printer epson cx8300 and have it connected to a print server TP-LINK TL-PS310U in a hope that every PCs on the network can share the printer to do printing and scanning. When I did a test to check if I can send a job to the printer, I could actually print it through the print server. However, the problem now is I can not scan a document. When I went to open windows Fax and Scanner window, unable to see any scanner there. So my question is whether this is the limitation of the epson printer itself or the print server or the scanners do not work on the network.
View 1 Replies View RelatedI've recently bought a WRT120N router, when I install the router using the CD an error occured error 322 New router or gateway not detected. I tried to download new version of firmware but it didnt work.
View 9 Replies View RelatedI am using the E3200 in a bridge mode to my uverse wifi router, since the E3200 has 5ghz and my uverse router doesn't. every week or so, I would not be able to detect the E3200 on my Mac Book Pro (I only enabled 5ghz on the E3200), but I can connect to the 2.4ghz uverse router, then access the admin page of the E3200 w/o.
View 6 Replies View RelatedI'm having problems getting the WUSB54G v2 adapter work with the WRT160N router (firmware 2.0.03). I'm running Vista Home Premium SP1. My wireless network is not detected by the WUSB54G and is not on the list of wireless networks I can connect to. I'm also having trouble connecting to WUSB54GP ver 4. The network is detected, but I can't connect.
Change the Beacon Interval to 75
Change the Fragmentation Threshold to 2304
Change the RTS Threshold to 2307
Now the WUSB54GP ver 4. is working perfectly, but the WUSB54G v2 still can't detect the network. I'm also running a PS3 and a laptop, which work perfectly with the WRT160N router.Also, the WUSB54G v2 system works just fine with my old router (WRTP54G).
just brought this router model #wrt120n and can't get setup disk to install because it says i have no ethernet port
View 1 Replies View RelatedI've been using a WRT150N wireless router successfully up until a couple days ago, when it stopped being detected. I can plug my computer directly to my modem, and it works, so my internet connection is fine. I have an older BEFW11S4 router that I am using currently, but it is very slow compared the the N router. I've tried resetting the 150N router, and also the modem, and combinations of both, but nothing seems to work. I plugged the router into my computer without connecting the modem, but I'm not able to access 192.168.1.1 either. All the lights illuminate when the router is plugged in.
View 9 Replies View Relatedi have my E1000 network detected by laptop and devices but can't connect to Internet. The E1000 is connected to Cisco 2100 modem and I can connect to Internet if I plug my laptop/PC directly to Cisco 2100 modem.
View 2 Replies View RelatedI am having trouble getting my Ricoh printer/scanner to communicate with the pc. It does not loop back completely without a "check the configuration network." I am not certain if the path is not right or I may be doing something else. I need to get the email function to work with my computer. I am using static ip address to communicate with the devices.
View 1 Replies View RelatedI've got a bit of an issue. A friend of mine has recently gotten windows 7 installed into his desktop. When he tried to install the network adapter (wusb11 version 2.8), it installed. However, when we searched for it in the device manager, it did not appear. does Version 2.8 only cover up to Windows XP or is there software to make it work for Windows 7?
View 3 Replies View RelatedI have a recurring issue with my e4200v1. My wired and wireless connections work fine, but I can't get to the administration website. I have https only set up, and after I get thru the 'certificate error' screen, I get an error that says web page is unavailable. Firfefox tells me that the connection was lost - error 101.I have tried wired and wireless, multiple computers, multiple browsers. I even turned the firewall off on one computer (or I think I did anyway).The only way I know how to fix it is by completely resetting then setting up the router all over again.
View 2 Replies View RelatedUpgraded from WRT610N to E4200. Since upgrading to latest firmware the wan just disappears both 5 and 2.5 Ghz bands. Happened with older firmware but not as often. Using it in briged mode. When this happens I can't even get to the management page with a lan connected pc. Have to do a hard reboot to get it to respond again. This is unacceptable for a router at this price point.
View 2 Replies View Relatedi keep getting an error message when i scan. error message: cannot communicate with scanner for these reasons
-scanner is turned off
-scanner is disconnected (it is disconnected from LAN, if using on LAN)BUT MY MACHINE IS ON
I have a Hp 4700 all in one wireless printer. I am able to print with no problem. I just can't copy or scan. when you first turn the pritner on it comes up with a scan/copy error. I have tired everything and nothing works.
View 1 Replies View RelatedI have an HP G60-530US laptop with Windows 7 Home Premium 64-bit. I bought a Linksys AE1200 USB Wireless Network Adapter because the laptop stopped recognizing the internal wireless adapter. However, when I use the CD that came with the Linksys adapter to install it, the adapter is not detected. I have tried different USB ports and also power-cycling the router & cable modem & rebooting. Nothing seems to work. I also ran the Setup program on my Gateway DX4860 desktop but the Linksys AE1200 is not detected on the desktop, either.
View 2 Replies View RelatedI recently upgraded my computer (not laptop) from Windows XP to Windows 7-32 bit. I redownloaded and installed Network Magic, Linksys Wireless Manager and my WUSB600N adapter properly (I hope). Now everything was working fine, I was able to get onto my network through the adapter but today I noticed that the Linksys Wireless Manager seemed to not connect to my network, instead my computer some how did it without the wireless manager. Now when I tried to connect to a network through the Wireless Manager it said Error: 211 and said My Adapter may not be installed properly and told me to remove the adapter and attach it back after 20 seconds. I tried that but again my computer connected to the network STILL through the computers own manager not through the Linksys Wireless Manager. That was still saying Error 211. So the problem really is that the Linksys Wireless Manager wont detect my adapter but my computer is still able to detect it and connect to my network.
View 4 Replies View RelatedI am connecting the E4200 to a Sonicwall TZ100. I want the TZ100 to assign IP addresses to devices that connect to the LAN via the E4200.
How do I have the E4200 act as a WAP only or not assign IP addresses and push that responsibility to the TZ100?
I'd still want the E4200 to have a SID key for LAN access security.
I have a 6 month old Cisco e-4200 router that is updated to the latest firmware, connected to a Motorola surfboard modem on Sudden-link in Midland, TX.
I previously used this exact same setup on Cox Cable in Wichita, KS with no problems. Upon setting it up down here I cannot get the router to pickup an IP address. I have Power-cycled everything multiple times, did a complete reset and re-installation of the router software and still no luck. The Sudden-link techs have no idea what is wrong. They said that the modems signal is strong and everything should be working.
Actually I did get it to work once for a couple of days, however when redoing the surround sound system I had to unhook the cable line and it quit working and I haven't gotten it to work again since. I have tried unhooking everything. Turning it all off. Waiting for 5+minutes, and then reconnecting in order: First the modem, then an ethernet cable to the computer which will usually work. But as soon as I unplug the cable from the computer and plug it into the router it stops working.
I bought Linksys E4200, at a time that is the TOP of the line Cisco routers for Home use.I noticed a serious usage issue with it, I could not identify which are the wifi devices connected to choose for access restriction or parental controls, as the dialog box state only as "Network device", and software control by Linksys does not have any provision to use MAC ID or any other option "except " looking at the dialog box as "Network device".
View 4 Replies View RelatedHow to connect the e4200 to a mac via afp? Trying to mount the network drive so the mac see it and can use for time machine backup.
View 3 Replies View RelatedTrying to update it to the new smart Wifi but getting this error "Incorrect Image File".Yes Ive tried redownloading yes ive tried different browers and yes to unziping the file! and Yes Im downloading the correct version I even tried version 1 for the heck of it and still nothing.
View 3 Replies View RelatedI just received by replacement e4200 v1. I updated the firmware to 1.0.03 build 14 and am up and running just fine. The specs say e4200 should be 300+450Mbps. I am using a software "inSSider 2.0" to view my wireless setup. I get 144(N) at 2.4GHz and 450(N) at 5.2GHz. Please note these are max bit rates and not connect speed or throughput rate. The "inSSider" software gives me the following:
2.4GHz - 1/2/5.5/6/7/9/11/12/14/18/22/124/28/29/36/43/44/48/54/58/65/72/86/116/130/144
5.2GHz - 6/9/12/15/18/24/30/36/45/48/54/60/90/120/135/150/180/240/270/300/360/405/450
I get this information by hovering on the max bit rate field on the row displaying my SSID. So is it correct to say that my e4200 is not designed to reach 300Mbps at 2.4GHz. There is an earlier discussion thread about connection maxing out 144. Please note I am not talking about connect speed or thru-put speed. Max design bit rates of dual band router labeled e4200.
Just got a e4200. However I also have a cisco av power line adapter which worked fine. However when connecting to the 4200 it doesn't recognize the Internet. Have rebooted, reset switched ports etc. But it still doesn't work. It sees the network but not the Internet. Have tried everything ikon but no luck. Cannot connect my directive to the Internet. If I can't get it to work will have to run a 50 foot cable.
View 5 Replies View RelatedFirmware 1.0.00 on my E4200 Hardware v1.0 provided a functioning 6to4 tunnel through Comcast's 6to4 facility. Windows and Linux clients on my local network discovered IPv6 addresses and were able to use them successfully.Unfortunately, after the upgrade to 1.0.03 this functionality was gone. I missed reading the ChangeLog, which said that the automatic tunneling feature was removed in 1.0.01. The now provided IPv6 functionality works much less well. First, automatic configuration (discovery of the 6to4 via IPv4 anycast) no longer works with Comcast's gateway. If I configure the tunnel manually, by specifying a 2002/16 prefix, I regain IPv6 connectivity, but only for Linux clients on my local network.
Windows 7 clients suffer from the problem that because the E4200 hands out ULA addresses, they end up preferring those ULA addresses when making global IPv6 connections in the IP 'source' field, which of course does not work. It's like putting your company mailbox code as the return address on a letter you send via US Mail. Other home routers, such as the AVM Fritz! (url,...) suffer from the same problem. However, they provide an option to turn off ULA at the router.Is it possible to turn off ULA for the E4200?
I have a E4200 router v.01 and when i updated the latest firmware (due to security exploit) it seems that whenever i acess the router settings (192.168.1.1) it doesn't ask me nor to input the admin and the password anymore, using wifi or wired.. I want the usual proccess whenever i go to 192.168.1.1 it will ask me to input my admin and password to change my router settings..
View 4 Replies View RelatedI have an E4200 and the Cisco VPN client on my home computer that I use to access a work network. The VPN client cannot connect unless I either (a) bypass the E4200 and connect directly to my cable modem or (b) disable the SPI Firewalls on the router. I have all the VPN passthroughs set to "enable" on the router, but still cannot connect. The VPN client is using IPSEC over TCP on port 10000.
View 5 Replies View RelatedI've been trying to get FTP Running up on my router for some time now.
I know my current WAN address and have setup a specified folder on my E4200 for the FTP partition. A username for myself has been created with login info and I have forwarded the port I have specified on my router's FTP configuration page.
I try to log into the server, but whenever I try to log into it, I keep getting a "incorrect login information" message back at me.
If I cancel out of that then I get an error message saying it can't find the specified folder and to check the address of the server.
I know the login information information is correct and I've tried changing the password to others of varying lengths.
I've also tried changing the port I'm running the FTP off of incase my ISP has blocked that port, nothing works.
I have a 6 year old wrt54g that is working fine but old. I want to upgrade and will go with the 3200 or 4200. I really don't need the extra features on the 4200 since everything I have is hardwired (directly to two laptops and to two switches in other parts of the house for tv and printer). I want wireless for times when we move a laptop but it wouldn't be all the time, and we won't (for now) use the media options. The difference in price between the 3200 and 4200 is less than $25 so costs is NOT a factor in deciding.So should I just purchase the 4200 since price is not a factor or go with 3200; I want the most stable of the two and will never need the extra wireless features in the 4200.
View 8 Replies View RelatedI bought a Linksy E4200 yesterday and set it up fine, but I only seem to be able to get 130 Mbps on my Wi-Fi. I looked through these threads and tried disabling the 2.4Ghz band and it still remains at 130Mbps. There was no change, also read I can try set up a secondary SSID. I really don't know much about routers or configuring them
View 4 Replies View Related