I am using the E3200 in a bridge mode to my uverse wifi router, since the E3200 has 5ghz and my uverse router doesn't. every week or so, I would not be able to detect the E3200 on my Mac Book Pro (I only enabled 5ghz on the E3200), but I can connect to the 2.4ghz uverse router, then access the admin page of the E3200 w/o.
View 6 RepliesI just got a Macbook Air and couldn't get connected at home so I went and bought a new router (our other router was old!!). We purchased the E1200. Our Dell desktop seems to have a fine connection, but my MacBook Air and my husbands laptop are really slow when on the internet.
View 1 Replies View RelatedI just bought a Linksys WRT160N router. I pop the installation disk in my mac book pro and walk thru the installation procedure successfully.But I can't connect wirelessly from my MacBook Pro (running mac os x 10.5).It sees the router and I did type in the password correctly (i copy from the text file generated by the installation procedure), but I keep getting 'coonnection timeout'.
View 9 Replies View RelatedI have the Linksys E2000 and set it up on MacBookPro no problems. My iPhone 3G and my gf's iPhone4 connect no problem. Also, I have an XBox 360 connected via ethernet cable. Her MacBook however is constantly not getting an IP. I set her up with an EZ Key, but every time she connects we have to go through the EZ key process where I run Cisco Connect from my laptop. Why can't she just log in every time? This is frustrating me as all other aspects of this router work fine. I had her plugged into it as well with no problems. Again, it works after a dual computer Cisco Connect cycle, but my computer isn't always home.
View 1 Replies View RelatedAny success with a recent vintage Macbook Pro connecting to the 5.8Ghz channel on a WRT610N. I can connect with the 2.4 channel without a problem but I cannot maintain a connection on the high channel. Linksys support told me that the hardware was not compatible with the high channel.
View 3 Replies View RelatedI just replaced my WRT54G with a WRT120N. Everything is working fine, but...
My MacBook Pro (about 18 months old) claims to support a/b/g/n, but it only wants to connect using 802.11g. It's running Snow Leopard. The laptop and the router are about 3 feet apart. Is there some incompatibilityin the version of 802.11n they support?
I just set up a new EA3500. I added my HP Photosmart C4680 printer, however, my computer can not find. In other words, the router could see it to add it, but my computer can not find the printer at the router. MacBook Pro OS 10.6.8
View 3 Replies View RelatedMy macbook keeps loosing it's wireless connection after being idle, when I start up I have to find my router and highlight it and connect and if it's idle it losers it's connection all the time.I tried resetting the router to default and started over I also tried every imaginable way of saving my password and connection but I can't find a way I've been into the routers security,trouble shooting,wireless, what's not holding it's connection to my MACBOOK? my iphone 5, ipad, and roku all hold
View 2 Replies View RelatedI recently purchased a Linksys e3000 router. Everything is going great except that both my desktop (Windows 7 Machine) and Laptop (Macbook Pro) keep losing the connection to a DLINK 323 Nas drive I have plugged into the router. This is problematic because I keep my itunes library on the NAS drive.
View 1 Replies View RelatedI recently purchased a Linksys e3000 router. Everything is going great except that both my desktop (Windows 7 Machine) and Laptop (Macbook Pro) keep losing the connection to a DLINK 323 Nas drive I have plugged into the router. This is problematic because I keep my itunes library on the NAS drive.
View 2 Replies View RelatedI've just confirmed that everytime I try to stream music from my MacBook Pro (iTunes) that is connected to my WiFi network using the 5GHz mode (channel width is Auto, channel: Auto (DFS)) to a couple Airport Express cubes are connected via the 2.4 GHz WiFi (channel width: Auto, channel: 10) the E4200 router reboots. When I set the MBP to use the 2.4 GHz mode I can stream music without causing the E4200 to reboot. The E4200 is running firmware 1.0.03.
View 9 Replies View RelatedI just bought an E3000 router. The Setup that comes in the CD does not support OSX 10.7.2 which is the latest version of the operating system.Is there some way to connect it wirelessly to a MacBook running 10.7.2?
View 3 Replies View RelatedHow to set up a time machine MacBook Air (Mac OS X 10.7.4) on EA4500 (2.0.37) with the disk WD MyBook USB 2TbThe disk is divided into two sections 500 and 1500, 500 by the time machine.After the command (defaults write com.apple.systempreferences TMShowUnsupportedNetworkVolumes 1) time machine saw the network drives, but can not be backed up (not supported AFP)
View 8 Replies View RelatedI have installed Ver.1.0.03 (Build 14) Firmware on my E4200 I launch cisco and detct the printer fine prints fine but goes to offline and my scaner in that printer not work My printer is cx7400.
View 1 Replies View RelatedI've recently bought a WRT120N router, when I install the router using the CD an error occured error 322 New router or gateway not detected. I tried to download new version of firmware but it didnt work.
View 9 Replies View RelatedI'm having problems getting the WUSB54G v2 adapter work with the WRT160N router (firmware 2.0.03). I'm running Vista Home Premium SP1. My wireless network is not detected by the WUSB54G and is not on the list of wireless networks I can connect to. I'm also having trouble connecting to WUSB54GP ver 4. The network is detected, but I can't connect.
Change the Beacon Interval to 75
Change the Fragmentation Threshold to 2304
Change the RTS Threshold to 2307
Now the WUSB54GP ver 4. is working perfectly, but the WUSB54G v2 still can't detect the network. I'm also running a PS3 and a laptop, which work perfectly with the WRT160N router.Also, the WUSB54G v2 system works just fine with my old router (WRTP54G).
Trying to convert a spare router (Linksys E3200) into a wireless access point toextend my wireless coverage. I thought knew how to do this but having a problem.Steps I followed are:1. Disable the E3200 DHCP server2. Change E3200ip address from 192.168.1.1 to something else3. Disable the firewall4.Make wireless settings5. Connect it lan port to lan port with primaryrouter.The problem I am having is that after I finish step 2 the routerreboots with the browser trying to access it at the new ip address. But thebrowser will not connect.I am doing this on a laptop that is disconnected from my network while I am working on the E3200. It is connected byan ethernet cable to an E3200 lan port. I also tried it wireless with the same result. Browser will not connect at any ip address except 192.168.1.1 and then only after I factory reset the beast to regain the 192.168.1.1 ip address
View 3 Replies View RelatedI just updated to the new firmware 1.0.02 and the USB stop working for my External Hard WD 500GB harddrive. I had to roll back to firmware 1.0.01 for it work
View 2 Replies View RelatedFirmware is 1.0.05 (didn't work on 1.0.04 too). It has a single partition formated as ntfs, any hint why it doesn't work or diagnostic I could do?
View 2 Replies View Relatedjust brought this router model #wrt120n and can't get setup disk to install because it says i have no ethernet port
View 1 Replies View RelatedI've been using a WRT150N wireless router successfully up until a couple days ago, when it stopped being detected. I can plug my computer directly to my modem, and it works, so my internet connection is fine. I have an older BEFW11S4 router that I am using currently, but it is very slow compared the the N router. I've tried resetting the 150N router, and also the modem, and combinations of both, but nothing seems to work. I plugged the router into my computer without connecting the modem, but I'm not able to access 192.168.1.1 either. All the lights illuminate when the router is plugged in.
View 9 Replies View Relatedafter messing with it for a 2 days since I got it I cant seem to get more than 130.0 my last router had 300 same setup same distance
View 9 Replies View RelatedI just ordered the E3200. It's suppose to ship today. I know it comes with 1 USB port for hard drives. Is it possible to connect a USB hub to the router so that I can connect more than 1 hard drive?
View 1 Replies View RelatedI have been using an E3200 and it has been working great. I know have a need for wireless coverage in a distant part of my house and the current router won't get there. I also need wired in that spot of the house as well. I thought to buy a e1200 to use it as a WAP for that part of the house and also to have a few Ethernet ports come off it. Can I connect to my original E3200 wirelessly from the e1200 and then use the e1200 as a WAP and for Ethernet?
View 7 Replies View RelatedI just upgraded my router from 1.0.03 to 1.0.04, I have a few questions:After installing the firmware, I pressed the reset button at the back for almost 1mn, the power lighted as expected, I then unplug the power cord for 30 sec.The strange thing is that this did not lead to a reset of the configuration, all my settings are still here...!But the actual problem is that my internet speed is divided by two, I still have to confirm this observation on the long term.
View 1 Replies View RelatedI have to reboort my router every day to get back an internet connection? I have a desktop and a laptop plus iPads, etc. The laptop loses connectivity every day about the same time. My only solution so far is to reboot the router. I realize that the client lease time is set to 1 day by default but isn't it supposed to ask the modem for another day of life when this happens?
View 5 Replies View RelatedI'm using a DSL line that changes IP's. I have the E3200 set to auto, but everytime the IP changes, my internet goes down, and I get an ip of 127.0.0.1 on the status page. I then have to renew the ip and reboot. This happens once a day, usually.
View 3 Replies View RelatedI have a 6 year old wrt54g that is working fine but old. I want to upgrade and will go with the 3200 or 4200. I really don't need the extra features on the 4200 since everything I have is hardwired (directly to two laptops and to two switches in other parts of the house for tv and printer). I want wireless for times when we move a laptop but it wouldn't be all the time, and we won't (for now) use the media options. The difference in price between the 3200 and 4200 is less than $25 so costs is NOT a factor in deciding.So should I just purchase the 4200 since price is not a factor or go with 3200; I want the most stable of the two and will never need the extra wireless features in the 4200.
View 8 Replies View RelatedI used to have a Belkin router which was losing connectivity throughout the day for a few short moments. After looking at the logs it appears it was issueing a DHCP release randomy which explained the fault. Since it was old router I decided to replace it with a E3200. This worked fine for a few days but then I started to see similar symptions. So currently I am trying to figure out if it's the same issue as before. I tried looking for a log on the router to see if it was also losing/releasing the WAN IP, but apparently the router doesn't log it. I spoke to a tech rep on chat, but I don't think they understand what I was talking about (how frustrating). I even tried to explain it another way that if I hit the 'Release IP address' button and then hit the "Renew IP Adresss' button does this activity get logged.
Where can I find a log to see DHCP activity (on the WAN interface)? There is a DHCP log which shows all the LAN activity but this is not what I need for this issue. I find it hard to believe a mature vendor like Linksys doesn't log this activity?
House has 2 floors. I want to install 2 E3200, one on each floor, but both with the same SSID/Password, etc. so internet connection/streaming throughout the floor is seamless.
Both floors have network wall sockets ready and they all lead to the same modem/router so all devices plugged lead to the same network.
PS. both E3200 have been update to Firmware Version: 1.0.03
I have bought Linksys E3200 less than month ago.I have setup it, connected HD (WD My Book 1TB) through USB and it work good, without any problem.Than week ago, I turned off the router, because of my vacation. Yesterday, I came back, turned on the router. WiFi was working good, cable connection too. But there was no connection to HD. I had checked information about HD on admin page, router understood that it is HD, but not provided share access to folder, also, there was no button, to setup it.I disconnected HD, tried to connect it using the Cisco Connect, it provided mistake with USB connection to HD and than with HTTP connection to router. I disconnected HD, tried to connect it manually: connect HD -> go to admin page -> refresh to show HD -> admin page freeze... -> reboot of router manually.
There was a lot of tries to connect HD, but all was failed.I connect HD to computer, it works successfully.I checked connection to router through USB, using my card reader and SD flash card, it works successfully.Information about HW:
1. Linksys E3200, last update of firmware for German (was bought using German Amazon) country. (Cannot check it now, if needed will check)
2. Computer: Windows XP SP3
3. WD My Book 1TB (NTFS)
I updated my E3200 to 1.0.04 to try to resolve a wireless dropping issue. Now the connected USB storage no longer responds correctly (very delayed if connecting at all). When I try to provision new storage via the routers admin page, I do not get the permissions page.
View 9 Replies View RelatedI just picked up the E3200 and love it. This morning I hooked up my printer via the USB. Everything went smooth until I tried to print something. I thought nothing was happening, but I let it sit for a while. While I was waiting, I was messing around with my network setting in windows. I realized that my network had been set to 'work' for some reason, so I changed it to 'home'. As soon as I did, my printer spit out my test page. (probably 5 min after sending the doc.) I don't know if it was just coincidence or what, so I sent another page and nothing happened (yet).
Is this common to take that long? Is there a way to speed this up?