Linksys Wireless Router :: WRT150N Successfully Up / Now Stopped Being Detected
Jul 10, 2011
I've been using a WRT150N wireless router successfully up until a couple days ago, when it stopped being detected. I can plug my computer directly to my modem, and it works, so my internet connection is fine. I have an older BEFW11S4 router that I am using currently, but it is very slow compared the the N router. I've tried resetting the 150N router, and also the modem, and combinations of both, but nothing seems to work. I plugged the router into my computer without connecting the modem, but I'm not able to access 192.168.1.1 either. All the lights illuminate when the router is plugged in.
View 9 Replies
ADVERTISEMENT
Apr 24, 2013
currently using Linksys Cisco E2000 ,Firmware 1.0.04.Trying to few block sites from Access restriction - bellow is the screen shot its not working. I have alos enabled SPI Firewall from Security Tab. how could I block site successfully.
View 9 Replies
View Related
Sep 21, 2012
No matter what I do, whenever I enter the Web Interface for my E4200, the page comes up in Russian (at least I think it is russian!!)! I have changed the language to English (by trial and error discovered it was the first option at the top of the pull-down list) many times and yes, selected save at the bottom of the Setup page. I get the message back "Your settings have been successfully saved".But next time I go in, it is back to either Russian or sometimes some other wierd script, and I have to reselect English.
View 2 Replies
View Related
Nov 26, 2007
I'm trying to setup Xbox live for my Xbox 360. I have the WRT150N wireless router and just got the wireless adapter that plugs into the 360. It said the adapter couldnt pick up the signal then i realized i needed to enter the WPA key from my wireless router. I checked the information on the router and it only gives me the serial number and MAC address. How I can find out what the WPA key is for the router??
View 5 Replies
View Related
Aug 8, 2012
I have a wrt150N that I am trying to determine whether it's dead or not. I cannot connect to it directly, even if I plug my laptop directly into the Router. Pressing the Reset button does nothing, the lights don't even flash?If I change my Ethernet cable it does represent which port I'm using but I can't ping 192.168.1.1 either? I want to try and flash the bios but A: there's no file to download for this model and B: I presume I need to be able to connect in order to do the flash?
View 4 Replies
View Related
May 13, 2011
I am currently at a friends house attempting to fix a situation he is having with his' wireless router, it is a Linksys WRT150n.Connection to the internet is possible via ethernet connectivity, however wireless is another story, devices can see the network but cannot connect to it, i have disabled the security key from the network to see if it was a simple password incorrection but still no dice.The current basic wireless settings have network mode set to mixed, and radio band, wide and standard channels set to auto, all other settings in the advanced tab are set to their default values.
View 1 Replies
View Related
Jan 23, 2008
I have the wireless-n wrt150n router. I have it wired to my computer and have it wirelessly connected to my ps3. But for some reason there is another unnamed device listed under My Network. My network was not secure before, but I changed it to secure when I noticed the unnamed device. How do I remove that unnamed device from my network?
View 3 Replies
View Related
Nov 24, 2007
Laptop keeps disconnecting from WRT150N
View 9 Replies
View Related
Sep 1, 2012
I want to replace a WRT150N with an E2500 and retain the setup/settings of the WRT150N.
View 2 Replies
View Related
Sep 7, 2012
Up until about midnight tonight, my router, which has been plugged in to my cable modem, has been working fine for years, both wired and wirelessly. Suddenly, however, I went to log on to my desktop PC (wired connection; Windows 7), and I had no network connection. ipconfig indicated "media disconnected." My cable-based phone service (VOIP) is still working fine at this time.
First attempt - unplug router, wait 15 seconds, plug it back in. Still no good, though my network sharing center indicated that the network connection was appearing/disappearing every few seconds, never actually getting "internet" connectivity.
Second attempt - attempted to use a WIFI-based device (iPad), which could not see my home network by name at all.
Third attempt - reset both the cable modem and the router, bringing the cable modem up FIRST. Same results as the first attempt.
Fourth attempt - plug the wired PC directly into the cable modem - this worked fine and is how I am submitting this post as I type. So the cable modem is working properly.
Fifth attempt - look up the information on how to reset the router to factory defaults. Used a paperclip to depress the reset button for 10- and on a subsequent attempt, 30-seconds (no obvious "reset" blink pattern was observed). Plug PC back in to router. PC would not obtain any DHCP-based IP address and the network sharing center was still behaving as in the first attempt.
Sixth attempt - disconnect the cable modem uplink and see if I could get the local network functioning. Now I noticed that the LED patterns on the router were behaving as:
- Power and my PC's slot number lit
- All lights lit
- All lights off
- Power and my PC's slot number lit
- etc
View 2 Replies
View Related
Aug 6, 2011
In my home I have a cable modem wired to a links wireless router a wrt 300n in my office (only hardwired used in there) and I do not get such good distance to my back bedrooms with my laptop. I have run a Ethernet cable dead center of the house for my sat receiver that is connected and wired to the 300wrt. Here is my question can I use the 150 like a hub or switch at the office connected to the cable modem and use the wrt300n router so that I get wireless on that side of the house. Or in reading here I see I can maybe use a bridge. I do have a older Linksys wrt150n sitting in a box.I have read until my eyes are almost bleeding and am not sure. How I can get a better signal on the other side of the house.
View 4 Replies
View Related
Jan 6, 2012
Changing the NAT Type to open because I can't play with some of my friends on Playstation.
View 1 Replies
View Related
Dec 31, 2011
chaning the NAT Type to open because I can't play with some of my friends on Playstation.
View 2 Replies
View Related
Nov 9, 2012
I can get regarding using the Collobos Fingerprint software through my WRT150N router. I'm using Windows XP SP3 and immediatly after installing (which went extreamy well) it immediatly found and listed all of my home network printers. All of the wired and wireless windows based systems in my house can see and print to the printers without any problem. However, getting ANY of my apple devices (iPad, iPhone etc ) to print will not even show them as listed on the device when I select print on the devices. Collobos says that I have to make sure that Ports UDP 5353 doe Bonjour and TCP 6361 for FingerPrint need to be open both ways for it to work, I have no problem getting into the router settings and have set them up as stated above in Port Range Triggering and enabled. Also made sure Filter Multicast was not check marked in Security. Unfortunatly, that doesn't seem to work as I had hoped.
View 3 Replies
View Related
Aug 21, 2011
I have a router that I upgraded the firmware a while ago, I stopped using it several months ago, I was going to give this router to my sister, i tried a hard reset(30 seconds press reset, unplug, hold hold the reset, wait 20 sec, plug power, hold for 30 sec and release the reset) and I tried to login with admin admin and it doesn't accept it. I tried with another router dlink 614i and the same problem, after resetting it it's not accepting admin admin log/pass.
View 1 Replies
View Related
Apr 3, 2011
I am using a WRT150N with firmware v1.00.5. I have a Linux setup with Squid connected to the network with the gateway 192.168.23.254. The WRT150N has a gateway of 192.168.23.1. The WRT150N is also connected to an Apple Base Station which serves as the Access Point for WiFi users.Squid limits access for IP addresses listed under the .254 gateway. But once I change my gateway to 23.1, everything is accessible. I want to block sites as well on the WRT150N. But every time I try to put a new Access Restriction, it doesn't work.
View 4 Replies
View Related
Jul 28, 2012
It has happen suddenly : Internet is not working through WRT150N, though it work when directly connected to the modem. So I think it is a router issue :On the WRT150N, Internet light is flashing fast for 2 seconds, then is off for 2 seconds, then flashes, then is off and so on, wether there is a device (computer, modem, ...) plugged or not, through the blue ethernet connector.And sometimes, Internet light stays off from power on, whatever is done with ethernet connexions (yellow or blue).
When connected to the blue ethernet Internet connector, my pc ethernet lights don't blink (nor the link light or the data light)I have try the 30-30-30 reset cycle. But it doesn't improve.I have tried the loopback test : connect an ethernet cable from the one of yellow ethernet port of WRT150N to the blue ethernet of WRT150 N.Sometimes, the light for the yellow ethernet port goes on for a few seconds, while the Internet light continues to flash. After a few seconds, both go off.Sometimes, as soon as the loopback is made, the 2 lights go off, and if a computer is plugged to the yellow port, the ethernet lights of the computer and the router stays off.But I can access to WRT150N through Wifi and I can access to the web management.
View 7 Replies
View Related
Oct 31, 2012
Several "consultants" have told me that the problem probably lies within my Linksys WRT150N.However, upon pinging the router, it responds. I did not reset the router to factory default), I just pinged it, and it's there.My firmware is v1.0.04. My provider is Cox Communication, and the connection os cable modem.Curiously, my wife's I-Pad will not open these links either.Sample link that doesn't work: url... Upon website opening click on "weekly ad".
View 2 Replies
View Related
Feb 9, 2008
I had successfully set up my new WRT150N router and it was working. But then it just stopped after about 12 hours. All the lights on the front of the router are blinking. When I directly connect to the router, my computer can't detect it. I've browsed through these forums a bit and tried a few things - the reset button (60 seconds), unplugging the router, downloading the EasyLink Connect tool, but I'm still stuck.
View 5 Replies
View Related
Jan 21, 2008
I purchased a WRT150N in early Dec 07. I had a number of problems with the unit disconnecting from wired and wireless connections erratically anywhere from 1/2 hr to 10 hrs. of operation. Troubleshoot thru Linksys chat. Ended up replacing router. Now I am having the same problem with replacement router. I've updated my windows XP, SP2, updated Ethernet driver and manually reconfigured router per Linksys advise. Wife and my laptops have N adapters, primary PC is wired in. It seems to disconnect all connections at same time, totally random. The only way to reconnect is to power down router for a few seconds and then power up.
View 9 Replies
View Related
May 23, 2009
My Linksys WRT150N recently gave up on me and started to give me weird issues and started to disconnect (all the ports including wired & wireless) anywhere from 3 to infinite number of times per day and my only solution was to remove the power chord and connect it. I tried all possible ways possible including resetting the router, stopping SSID broadcast, removing the encryption, etc, but non worked. As the router was out of warranty my only option was to take it to the dealers where they told me it would take 3 weeks to fix and God knows how much they would have charged me. But after flashing the firmware with the dd-wrt it has been almost 24 hours without a single problem and now I have the cool option of seeing who is connected to the router, etc. This is a MUST for every Linksys owner.
1. Reset the router using 30-30-30 and waited for 2 minutes for things to come back 2 normal
2. Flashed the router with "dd-wrt.v24_mini_generic.bin"
3. Reset again using 30-30-30 and wait again4. Flashed the router with " dd-wrt.v24_std_generic.bin"5.
View 3 Replies
View Related
Jun 30, 2011
We have the Linksys WRT150N router. A while ago it suddenly lost the name we gave it when we set it up and now it shows up as Linksys. Also, it is no longer secure, and sometimes we can't even see our network - it isn't even listed. How do I go in and change this? Will I have to reset the wireless information on my printer, etc?
View 4 Replies
View Related
Jan 28, 2012
I have WRT150N, with firmware version 1.01.9 and I can not get the internet access policy to work.Here are my settings: PC list is configured through IP range as follows:Even if I deny internet access completely, I can still access the internet.
View 2 Replies
View Related
Nov 12, 2011
with my Linksys WRT150N router in "N-only" mode, the usb adapter WUSB100 doesn't connect. In the datasheet is written that it is B-G, but also N compatible..[URL] It connects only when the router is on "mixed mode" (B-G-N).
The device works great, the only thing is that it doesn't connect to N networks.... cause i think it is not N compatible. When i look for networks, Windows shows me that there is my N network, but when i click connect, after a few seconds, appears "impossible to connect".... but if i set the router on "mixed mode", no problems.
View 9 Replies
View Related
Feb 25, 2013
For the last 4 years I’ve been using the Linksys Router, model WRT150N V. 1.1 and never had any problems—until now.Yesterday I noticed that my wireless devices (i.e., two computers, tablet and Internet radio) either don’t work at all (the Internet radio) or the pages load extremely slowly—for example, the tablet has become, for all intents and purposes, unusable. Since my ‘main’ computer is connected directly to my cable internet, I know that there is nothing wrong with the Internet connection itself, only with wireless connection.I disconnected the Linksys Router for 2 minutes and reconnected it, but to no avail. I know that I have not made any changes to any software/hardware that might affect the speed.Since I also happen to have access to another wireless Internet connection (a different provider), I connected to that network and all my wireless devices were working perfectly. Therefore, I think the problem must be with the router. I am using Windows XP (on the main computer, where the router and Internet cable are attached).
View 5 Replies
View Related
Jul 4, 2011
I have two notebooks, one smartphone, and one blu-ray player that connects to my wireless network. My gaming PC is hard wired into the same router that broadcasts my wireless network. About 5-6 times, my wireless network will drop and everyone connected to it wirelessly will lose their connection for about 1-2 minutes. While my gaming PCs internet connection is undisturbed, all of my wireless devices can no longer "see" the network SSID and therefore connect to it. The problem has been happening consistently for many months.
View 1 Replies
View Related
Mar 14, 2008
Just purchased a RVS4000. How to be successfully able to VPN into this device from os/x? If so what software / settings required.
View 6 Replies
View Related
Feb 23, 2011
I have successfully connected my vpn to my central point and 2 branches.My branch can see central and visa versaMy problem is that i can't see from my 1 branch the other branch.
My central has RVS4000 and my branches has WRV200.How can i be able to access from my branch1 PC, my branch2 PC and visa versa
View 1 Replies
View Related
May 10, 2011
I had a power outage and reset modem and wireless router(linksys WRT150N) I can connect to internet when I use ethernet cable but when I go wireless I sometimes can't see wireless network, sometimes I can see network but it wants WEP password even though security is disables and other times it connects no problem. It happens on both a MAC and a PC.
View 1 Replies
View Related
Mar 18, 2013
I have a Linksys Wireless G PCI adapter. The model is WMP54gs and the serial number MGP00E416793. I am trying to install this adapter on a Windows XP media center computer. The computer is update to date with all windows updates. I need the driver and software to successfully get this adapter to fully work.
View 3 Replies
View Related
Dec 7, 2011
I have installed Ver.1.0.03 (Build 14) Firmware on my E4200 I launch cisco and detct the printer fine prints fine but goes to offline and my scaner in that printer not work My printer is cx7400.
View 1 Replies
View Related
May 6, 2012
I've recently bought a WRT120N router, when I install the router using the CD an error occured error 322 New router or gateway not detected. I tried to download new version of firmware but it didnt work.
View 9 Replies
View Related
May 2, 2012
I am using the E3200 in a bridge mode to my uverse wifi router, since the E3200 has 5ghz and my uverse router doesn't. every week or so, I would not be able to detect the E3200 on my Mac Book Pro (I only enabled 5ghz on the E3200), but I can connect to the 2.4ghz uverse router, then access the admin page of the E3200 w/o.
View 6 Replies
View Related
