Linksys Wireless Router :: WRT150N - Unable To Print From Mac Devices
Nov 9, 2012
I can get regarding using the Collobos Fingerprint software through my WRT150N router. I'm using Windows XP SP3 and immediatly after installing (which went extreamy well) it immediatly found and listed all of my home network printers. All of the wired and wireless windows based systems in my house can see and print to the printers without any problem. However, getting ANY of my apple devices (iPad, iPhone etc ) to print will not even show them as listed on the device when I select print on the devices. Collobos says that I have to make sure that Ports UDP 5353 doe Bonjour and TCP 6361 for FingerPrint need to be open both ways for it to work, I have no problem getting into the router settings and have set them up as stated above in Port Range Triggering and enabled. Also made sure Filter Multicast was not check marked in Security. Unfortunatly, that doesn't seem to work as I had hoped.
View 3 Replies
ADVERTISEMENT
Sep 28, 2011
I have several devices connected to my EA4500 (two wired computers, two wireless laptops, iPhone, iPad, and a network drive). i have not been able to connect any new devices wirelessly. New laptops, PS3, friends laptops. Error message would suggest that password is being entered incorrectly, but I change the password to very basic word (idiot proof) but no luck.
View 9 Replies
View Related
Jul 28, 2012
We have Cable DSL modem that connects to router. One wired connection from router to PC. Wireless devices are 2 iphones 2 ipads and 2 imacs. Constantly having to power the WRT120N off and back on to regain connectivity.
View 2 Replies
View Related
Aug 19, 2012
I just switched to the EA4500 Router and I'm now unable to remotely access my camera devices. I have done the port forward. I can access the cameras from my local LAN both when using the local 10. ..and external 99 .. Addresses. When I go off the local connection - Access does not work. Slingbox did its auto configuration and I can access it. I just cant get to camera devices (Panosonic, Foscam, etc.).
View 3 Replies
View Related
Jan 3, 2012
I have a WRT610N which does not allow me to connect any new devices to the wireless network. This is a recent problem as I have been able to connect new devices before. Devices on the wireless network, those that have been on the network, are able to disconnect and reconnect. Just new devices are excluded. Have gone through the admin screens to see if something is amiss but can not find anything.
View 5 Replies
View Related
Nov 29, 2011
I have a WRT610 and am unable to connect any devices wirelessly. All the lights on the right hand side of the router are on except for the USB connection....what am I doing wrong? The router has worked for about a year flawlessly and last night all wireless connections quit.
View 9 Replies
View Related
Jul 3, 2011
I cant see in my network the devices connected to SE2500 just the SE2500 itself. The internet access of the devices connected to SE2500 is working correctly. Is this a problem?
View 3 Replies
View Related
Feb 23, 2012
I have a E4200 router. The firmware version is 1.1.02. I am reluctant to upgrade; however, my iMAC is picking up the 5GHz broadcast setting, but the rest of my wireless devices only recognize my lower 2.4GHz setting. I have changed channels, my router address is changed because it conflicted with my Verizon DSL. I do not have FIOS. What can I do to fix this problem. I have an ipad, 2 iphones, 2 ipod touches, 2 laptops (PCs), an XBOX, and a PS3 that needs to connect to a higher broadcast. The connections are slow and at times get dropped.
View 4 Replies
View Related
Nov 26, 2007
I'm trying to setup Xbox live for my Xbox 360. I have the WRT150N wireless router and just got the wireless adapter that plugs into the 360. It said the adapter couldnt pick up the signal then i realized i needed to enter the WPA key from my wireless router. I checked the information on the router and it only gives me the serial number and MAC address. How I can find out what the WPA key is for the router??
View 5 Replies
View Related
Aug 8, 2012
I have a wrt150N that I am trying to determine whether it's dead or not. I cannot connect to it directly, even if I plug my laptop directly into the Router. Pressing the Reset button does nothing, the lights don't even flash?If I change my Ethernet cable it does represent which port I'm using but I can't ping 192.168.1.1 either? I want to try and flash the bios but A: there's no file to download for this model and B: I presume I need to be able to connect in order to do the flash?
View 4 Replies
View Related
May 13, 2011
I am currently at a friends house attempting to fix a situation he is having with his' wireless router, it is a Linksys WRT150n.Connection to the internet is possible via ethernet connectivity, however wireless is another story, devices can see the network but cannot connect to it, i have disabled the security key from the network to see if it was a simple password incorrection but still no dice.The current basic wireless settings have network mode set to mixed, and radio band, wide and standard channels set to auto, all other settings in the advanced tab are set to their default values.
View 1 Replies
View Related
Jan 23, 2008
I have the wireless-n wrt150n router. I have it wired to my computer and have it wirelessly connected to my ps3. But for some reason there is another unnamed device listed under My Network. My network was not secure before, but I changed it to secure when I noticed the unnamed device. How do I remove that unnamed device from my network?
View 3 Replies
View Related
Nov 24, 2007
Laptop keeps disconnecting from WRT150N
View 9 Replies
View Related
Sep 1, 2012
I want to replace a WRT150N with an E2500 and retain the setup/settings of the WRT150N.
View 2 Replies
View Related
Sep 7, 2012
Up until about midnight tonight, my router, which has been plugged in to my cable modem, has been working fine for years, both wired and wirelessly. Suddenly, however, I went to log on to my desktop PC (wired connection; Windows 7), and I had no network connection. ipconfig indicated "media disconnected." My cable-based phone service (VOIP) is still working fine at this time.
First attempt - unplug router, wait 15 seconds, plug it back in. Still no good, though my network sharing center indicated that the network connection was appearing/disappearing every few seconds, never actually getting "internet" connectivity.
Second attempt - attempted to use a WIFI-based device (iPad), which could not see my home network by name at all.
Third attempt - reset both the cable modem and the router, bringing the cable modem up FIRST. Same results as the first attempt.
Fourth attempt - plug the wired PC directly into the cable modem - this worked fine and is how I am submitting this post as I type. So the cable modem is working properly.
Fifth attempt - look up the information on how to reset the router to factory defaults. Used a paperclip to depress the reset button for 10- and on a subsequent attempt, 30-seconds (no obvious "reset" blink pattern was observed). Plug PC back in to router. PC would not obtain any DHCP-based IP address and the network sharing center was still behaving as in the first attempt.
Sixth attempt - disconnect the cable modem uplink and see if I could get the local network functioning. Now I noticed that the LED patterns on the router were behaving as:
- Power and my PC's slot number lit
- All lights lit
- All lights off
- Power and my PC's slot number lit
- etc
View 2 Replies
View Related
Aug 6, 2011
In my home I have a cable modem wired to a links wireless router a wrt 300n in my office (only hardwired used in there) and I do not get such good distance to my back bedrooms with my laptop. I have run a Ethernet cable dead center of the house for my sat receiver that is connected and wired to the 300wrt. Here is my question can I use the 150 like a hub or switch at the office connected to the cable modem and use the wrt300n router so that I get wireless on that side of the house. Or in reading here I see I can maybe use a bridge. I do have a older Linksys wrt150n sitting in a box.I have read until my eyes are almost bleeding and am not sure. How I can get a better signal on the other side of the house.
View 4 Replies
View Related
Jan 6, 2012
Changing the NAT Type to open because I can't play with some of my friends on Playstation.
View 1 Replies
View Related
Dec 31, 2011
chaning the NAT Type to open because I can't play with some of my friends on Playstation.
View 2 Replies
View Related
Aug 21, 2011
I have a router that I upgraded the firmware a while ago, I stopped using it several months ago, I was going to give this router to my sister, i tried a hard reset(30 seconds press reset, unplug, hold hold the reset, wait 20 sec, plug power, hold for 30 sec and release the reset) and I tried to login with admin admin and it doesn't accept it. I tried with another router dlink 614i and the same problem, after resetting it it's not accepting admin admin log/pass.
View 1 Replies
View Related
Apr 3, 2011
I am using a WRT150N with firmware v1.00.5. I have a Linux setup with Squid connected to the network with the gateway 192.168.23.254. The WRT150N has a gateway of 192.168.23.1. The WRT150N is also connected to an Apple Base Station which serves as the Access Point for WiFi users.Squid limits access for IP addresses listed under the .254 gateway. But once I change my gateway to 23.1, everything is accessible. I want to block sites as well on the WRT150N. But every time I try to put a new Access Restriction, it doesn't work.
View 4 Replies
View Related
Jul 28, 2012
It has happen suddenly : Internet is not working through WRT150N, though it work when directly connected to the modem. So I think it is a router issue :On the WRT150N, Internet light is flashing fast for 2 seconds, then is off for 2 seconds, then flashes, then is off and so on, wether there is a device (computer, modem, ...) plugged or not, through the blue ethernet connector.And sometimes, Internet light stays off from power on, whatever is done with ethernet connexions (yellow or blue).
When connected to the blue ethernet Internet connector, my pc ethernet lights don't blink (nor the link light or the data light)I have try the 30-30-30 reset cycle. But it doesn't improve.I have tried the loopback test : connect an ethernet cable from the one of yellow ethernet port of WRT150N to the blue ethernet of WRT150 N.Sometimes, the light for the yellow ethernet port goes on for a few seconds, while the Internet light continues to flash. After a few seconds, both go off.Sometimes, as soon as the loopback is made, the 2 lights go off, and if a computer is plugged to the yellow port, the ethernet lights of the computer and the router stays off.But I can access to WRT150N through Wifi and I can access to the web management.
View 7 Replies
View Related
Oct 31, 2012
Several "consultants" have told me that the problem probably lies within my Linksys WRT150N.However, upon pinging the router, it responds. I did not reset the router to factory default), I just pinged it, and it's there.My firmware is v1.0.04. My provider is Cox Communication, and the connection os cable modem.Curiously, my wife's I-Pad will not open these links either.Sample link that doesn't work: url... Upon website opening click on "weekly ad".
View 2 Replies
View Related
Feb 9, 2008
I had successfully set up my new WRT150N router and it was working. But then it just stopped after about 12 hours. All the lights on the front of the router are blinking. When I directly connect to the router, my computer can't detect it. I've browsed through these forums a bit and tried a few things - the reset button (60 seconds), unplugging the router, downloading the EasyLink Connect tool, but I'm still stuck.
View 5 Replies
View Related
Jul 10, 2011
I've been using a WRT150N wireless router successfully up until a couple days ago, when it stopped being detected. I can plug my computer directly to my modem, and it works, so my internet connection is fine. I have an older BEFW11S4 router that I am using currently, but it is very slow compared the the N router. I've tried resetting the 150N router, and also the modem, and combinations of both, but nothing seems to work. I plugged the router into my computer without connecting the modem, but I'm not able to access 192.168.1.1 either. All the lights illuminate when the router is plugged in.
View 9 Replies
View Related
Jan 21, 2008
I purchased a WRT150N in early Dec 07. I had a number of problems with the unit disconnecting from wired and wireless connections erratically anywhere from 1/2 hr to 10 hrs. of operation. Troubleshoot thru Linksys chat. Ended up replacing router. Now I am having the same problem with replacement router. I've updated my windows XP, SP2, updated Ethernet driver and manually reconfigured router per Linksys advise. Wife and my laptops have N adapters, primary PC is wired in. It seems to disconnect all connections at same time, totally random. The only way to reconnect is to power down router for a few seconds and then power up.
View 9 Replies
View Related
May 23, 2009
My Linksys WRT150N recently gave up on me and started to give me weird issues and started to disconnect (all the ports including wired & wireless) anywhere from 3 to infinite number of times per day and my only solution was to remove the power chord and connect it. I tried all possible ways possible including resetting the router, stopping SSID broadcast, removing the encryption, etc, but non worked. As the router was out of warranty my only option was to take it to the dealers where they told me it would take 3 weeks to fix and God knows how much they would have charged me. But after flashing the firmware with the dd-wrt it has been almost 24 hours without a single problem and now I have the cool option of seeing who is connected to the router, etc. This is a MUST for every Linksys owner.
1. Reset the router using 30-30-30 and waited for 2 minutes for things to come back 2 normal
2. Flashed the router with "dd-wrt.v24_mini_generic.bin"
3. Reset again using 30-30-30 and wait again4. Flashed the router with " dd-wrt.v24_std_generic.bin"5.
View 3 Replies
View Related
Jun 30, 2011
We have the Linksys WRT150N router. A while ago it suddenly lost the name we gave it when we set it up and now it shows up as Linksys. Also, it is no longer secure, and sometimes we can't even see our network - it isn't even listed. How do I go in and change this? Will I have to reset the wireless information on my printer, etc?
View 4 Replies
View Related
Jan 28, 2012
I have WRT150N, with firmware version 1.01.9 and I can not get the internet access policy to work.Here are my settings: PC list is configured through IP range as follows:Even if I deny internet access completely, I can still access the internet.
View 2 Replies
View Related
Nov 12, 2011
with my Linksys WRT150N router in "N-only" mode, the usb adapter WUSB100 doesn't connect. In the datasheet is written that it is B-G, but also N compatible..[URL] It connects only when the router is on "mixed mode" (B-G-N).
The device works great, the only thing is that it doesn't connect to N networks.... cause i think it is not N compatible. When i look for networks, Windows shows me that there is my N network, but when i click connect, after a few seconds, appears "impossible to connect".... but if i set the router on "mixed mode", no problems.
View 9 Replies
View Related
Feb 25, 2013
For the last 4 years I’ve been using the Linksys Router, model WRT150N V. 1.1 and never had any problems—until now.Yesterday I noticed that my wireless devices (i.e., two computers, tablet and Internet radio) either don’t work at all (the Internet radio) or the pages load extremely slowly—for example, the tablet has become, for all intents and purposes, unusable. Since my ‘main’ computer is connected directly to my cable internet, I know that there is nothing wrong with the Internet connection itself, only with wireless connection.I disconnected the Linksys Router for 2 minutes and reconnected it, but to no avail. I know that I have not made any changes to any software/hardware that might affect the speed.Since I also happen to have access to another wireless Internet connection (a different provider), I connected to that network and all my wireless devices were working perfectly. Therefore, I think the problem must be with the router. I am using Windows XP (on the main computer, where the router and Internet cable are attached).
View 5 Replies
View Related
Jul 4, 2011
I have two notebooks, one smartphone, and one blu-ray player that connects to my wireless network. My gaming PC is hard wired into the same router that broadcasts my wireless network. About 5-6 times, my wireless network will drop and everyone connected to it wirelessly will lose their connection for about 1-2 minutes. While my gaming PCs internet connection is undisturbed, all of my wireless devices can no longer "see" the network SSID and therefore connect to it. The problem has been happening consistently for many months.
View 1 Replies
View Related
Aug 15, 2011
I have installed my new E4200 and it works beautifully. I have several wirelss adapters and a few wired connections through powerline adapters. I also have a second VPN router attached to the 4200.I can see the wireless connected devices with the associated IP addresses. If I plug a laptop directly into the Cisco, I can of course see it.However, I can see none of the devices attatched to the powerline devices? I have a securty cam connected via the powerline and want to know the IP address. I checked with cisco technical support via chat and they said it is impossible. I have used 2 previous routers with the same configuration and can see all devices.
View 1 Replies
View Related
Mar 2, 2012
I recently upgraded my d-link router DI-524 for Netgear N600 WNDR3700v3 and every component (wired or wireless) is working except network printer. I have it wired directly to the router and all pcs on the home network can see it, however when i select to do a test print, nothing prints to the printer and i get error. I had this setup using the d-link router with both the printer and the XP PC wired directly to the router and using the XP PC as a network pc sharing the printer to other pcs (Vista / Windows 7) on the home network.The printer is a Toshiba e-studio 160 series.. I re-added the print drivers for XP and still not able to print. Is there anything else I can try?
View 9 Replies
View Related
