Linksys Wireless Router :: Can't Login To Wrt150N After Hard Reset
Aug 21, 2011
I have a router that I upgraded the firmware a while ago, I stopped using it several months ago, I was going to give this router to my sister, i tried a hard reset(30 seconds press reset, unplug, hold hold the reset, wait 20 sec, plug power, hold for 30 sec and release the reset) and I tried to login with admin admin and it doesn't accept it. I tried with another router dlink 614i and the same problem, after resetting it it's not accepting admin admin log/pass.
View 1 Replies
ADVERTISEMENT
Jun 30, 2011
We have the Linksys WRT150N router. A while ago it suddenly lost the name we gave it when we set it up and now it shows up as Linksys. Also, it is no longer secure, and sometimes we can't even see our network - it isn't even listed. How do I go in and change this? Will I have to reset the wireless information on my printer, etc?
View 4 Replies
View Related
Aug 20, 2012
I have an EA-4500. Unfortunately I often have to hard-reset it:
- every time I update the firmware (last time I updated to 2.1.38.138827 via Cisco Connect Cloud)
- sometimes whenever there is a black-out
The first time it happened upon the automic firmware update which released Connect Cloud. In such cases, the router stays with the white Cisco logo on and no other lights work (i.e. the ethernet lights on the rear side of the router are off). The only reset procedure working is: unplug Internet cable, press reset for 30 secs, turn off while keeping reset pressed, wait 30 more seconds, turn on again always keeping the reset pressed.
I've tried to turn off for 2 minutes but it doesn't work. The strange thing is that the above reset procedure does not always work, sometimes I have to do it like 10 times before the router Cisco logo light starts blinking on and off (like breathing).
Besides this, which is very very annoying, I'm satisfied with router functionalities and performance.
View 7 Replies
View Related
Feb 2, 2012
I was trying to do a hard reset and power went off. Since then if i plug in electricity in my router all lights lit once, then all turn off.
View 4 Replies
View Related
Mar 17, 2013
I have an e4200 with the latest firmware 2.1.39. I just upgraded the firmware due to connection issues with my DSL. I now have the same issues with disconnects but I believe they are being caused by a different issue. When I try and log into my router through the IP address it wont let me, it says it can't find the router. Eventually after getting in the first time by using the default password, I have twice found out that all my settings are gone. This has happened twice this week and only happened after upgrading the firmware but I can not tell if firmware is causing it or if it is hardware related. I now reboot and restore saved firmware but that is a hassle and am pretty sure that is not the way it was designed to work.
View 9 Replies
View Related
Oct 17, 2008
Ok, so I reset the router but i still can't login to the setup using the factory password (admin/admin) (blank/admin) (admin/blank). Now I have an unencrypted network and no access to the setup... I even tried using the setup CD but it doesn't recognize the router.
View 2 Replies
View Related
Jan 6, 2013
I recently rescued an old Belkin 54G router (Model: F5D7632-4) which I planned to use as an extra wireless access point towards the back of my house where I have some dead spots. I logged in on the Belkin's IP: 192.168.2.1 And went straight to change the IP and put it onto the same subnet as my router. I changed it to: 192.168.0.1 as I had it in my head my router was .254 My router is 192.168.0.1 so obviously this didn't do much and I couldn't access either device.
I unplugged my network and plugged directly into the Belkin to change to another IP and I cannot access it. The operation times out. I can access the normal router when I connect back up to the network fine. To solve this I decided to reset the router. The instruction manual for the Belkin says a momentary push on the reset will do a quick reset. while >20 seconds will perform a full hard reset. Both of these are signified by the power light flashing, and the reset is complete when the power light becomes solid again.
Unfortunately no matter how long I hold the reset button for, the light does not even blink and no reset happens. Obviously this may just be a dodgy reset switch, the router is getting quite old, so I will go in an short the reset pins by hand if I need to. The solution I am looking for is either to reset so I can start again - or obtain access to the router through some other means to change the IP and carry on. When I connect the Belkin to my network, the router cannot see it connected to it's Ethernet port. However the Belkin's link light occasionally flickers.
View 3 Replies
View Related
Apr 28, 2013
Region : Others
Model : TL-MR3420
Hardware Version : V2
Firmware Version : openwrt-mr3420-v2-HM2013-04-19
ISP : Cellcom Israel
how to make hard reset to MR3420.I installed openwrt-mr3420-v2-HM2013-04-19 software to my router.and after that while the router restart the led green lights flashing on and of all the time.and I cant contact to the router with wifi or lan cable
View 5 Replies
View Related
Apr 10, 2012
I have a WES610N in my office connected to a E4200 @ the cable modem in the family room. ~30'.The connection is fine and works well when working.Connected to the WES610N I have:
-Polycom VOIP phone
-HP Mediasmart Windows Home Server
-Desktop
-Multi-Function Laser Printer
I have two issues.
1) The Polycom does a random reboot that I have traced down to it loosing it's IP
2) The Windows Home Server looses it's IP requireing a hard reset.
I have enabled QOS for the polycom and that just worked with managing data. However both devices seem to loose their IP regularly. The desktop might also be having the issue but because it is Vista I suspect Vista is better equipped to deal with IP issues.
View 9 Replies
View Related
May 9, 2013
We have a Linksys WRT120N wireless router set up at one of our small offices. I noticed recently when trying to log in to the router to make some admin configurations that it will not accept the login credentials when trying to log in from IE10 browser. Works fine from Chrome, IE9, ect. logging in to a linksys router with IE10?
View 3 Replies
View Related
Oct 17, 2011
I got a problem with a ap that I have here where I do not have the password and I did the process to reset the AP to factory defaults, but the configuration still the same, and the AP still asking for the enable password, its the same problem poused before in this link URL. I did the same process but I still have the old configuration on the AP. I noticed that the AP change the image when I reset the AP, using the mode button. the AP is starting with and rcv image. I need to reset the AP to its initial configuration.
View 9 Replies
View Related
Nov 26, 2007
I'm trying to setup Xbox live for my Xbox 360. I have the WRT150N wireless router and just got the wireless adapter that plugs into the 360. It said the adapter couldnt pick up the signal then i realized i needed to enter the WPA key from my wireless router. I checked the information on the router and it only gives me the serial number and MAC address. How I can find out what the WPA key is for the router??
View 5 Replies
View Related
Aug 8, 2012
I have a wrt150N that I am trying to determine whether it's dead or not. I cannot connect to it directly, even if I plug my laptop directly into the Router. Pressing the Reset button does nothing, the lights don't even flash?If I change my Ethernet cable it does represent which port I'm using but I can't ping 192.168.1.1 either? I want to try and flash the bios but A: there's no file to download for this model and B: I presume I need to be able to connect in order to do the flash?
View 4 Replies
View Related
May 13, 2011
I am currently at a friends house attempting to fix a situation he is having with his' wireless router, it is a Linksys WRT150n.Connection to the internet is possible via ethernet connectivity, however wireless is another story, devices can see the network but cannot connect to it, i have disabled the security key from the network to see if it was a simple password incorrection but still no dice.The current basic wireless settings have network mode set to mixed, and radio band, wide and standard channels set to auto, all other settings in the advanced tab are set to their default values.
View 1 Replies
View Related
Jan 23, 2008
I have the wireless-n wrt150n router. I have it wired to my computer and have it wirelessly connected to my ps3. But for some reason there is another unnamed device listed under My Network. My network was not secure before, but I changed it to secure when I noticed the unnamed device. How do I remove that unnamed device from my network?
View 3 Replies
View Related
Nov 24, 2007
Laptop keeps disconnecting from WRT150N
View 9 Replies
View Related
Sep 1, 2012
I want to replace a WRT150N with an E2500 and retain the setup/settings of the WRT150N.
View 2 Replies
View Related
Sep 7, 2012
Up until about midnight tonight, my router, which has been plugged in to my cable modem, has been working fine for years, both wired and wirelessly. Suddenly, however, I went to log on to my desktop PC (wired connection; Windows 7), and I had no network connection. ipconfig indicated "media disconnected." My cable-based phone service (VOIP) is still working fine at this time.
First attempt - unplug router, wait 15 seconds, plug it back in. Still no good, though my network sharing center indicated that the network connection was appearing/disappearing every few seconds, never actually getting "internet" connectivity.
Second attempt - attempted to use a WIFI-based device (iPad), which could not see my home network by name at all.
Third attempt - reset both the cable modem and the router, bringing the cable modem up FIRST. Same results as the first attempt.
Fourth attempt - plug the wired PC directly into the cable modem - this worked fine and is how I am submitting this post as I type. So the cable modem is working properly.
Fifth attempt - look up the information on how to reset the router to factory defaults. Used a paperclip to depress the reset button for 10- and on a subsequent attempt, 30-seconds (no obvious "reset" blink pattern was observed). Plug PC back in to router. PC would not obtain any DHCP-based IP address and the network sharing center was still behaving as in the first attempt.
Sixth attempt - disconnect the cable modem uplink and see if I could get the local network functioning. Now I noticed that the LED patterns on the router were behaving as:
- Power and my PC's slot number lit
- All lights lit
- All lights off
- Power and my PC's slot number lit
- etc
View 2 Replies
View Related
Aug 6, 2011
In my home I have a cable modem wired to a links wireless router a wrt 300n in my office (only hardwired used in there) and I do not get such good distance to my back bedrooms with my laptop. I have run a Ethernet cable dead center of the house for my sat receiver that is connected and wired to the 300wrt. Here is my question can I use the 150 like a hub or switch at the office connected to the cable modem and use the wrt300n router so that I get wireless on that side of the house. Or in reading here I see I can maybe use a bridge. I do have a older Linksys wrt150n sitting in a box.I have read until my eyes are almost bleeding and am not sure. How I can get a better signal on the other side of the house.
View 4 Replies
View Related
Apr 28, 2012
I need to reset my login password
View 3 Replies
View Related
Jan 6, 2012
Changing the NAT Type to open because I can't play with some of my friends on Playstation.
View 1 Replies
View Related
Dec 31, 2011
chaning the NAT Type to open because I can't play with some of my friends on Playstation.
View 2 Replies
View Related
Nov 9, 2012
I can get regarding using the Collobos Fingerprint software through my WRT150N router. I'm using Windows XP SP3 and immediatly after installing (which went extreamy well) it immediatly found and listed all of my home network printers. All of the wired and wireless windows based systems in my house can see and print to the printers without any problem. However, getting ANY of my apple devices (iPad, iPhone etc ) to print will not even show them as listed on the device when I select print on the devices. Collobos says that I have to make sure that Ports UDP 5353 doe Bonjour and TCP 6361 for FingerPrint need to be open both ways for it to work, I have no problem getting into the router settings and have set them up as stated above in Port Range Triggering and enabled. Also made sure Filter Multicast was not check marked in Security. Unfortunatly, that doesn't seem to work as I had hoped.
View 3 Replies
View Related
Apr 3, 2011
I am using a WRT150N with firmware v1.00.5. I have a Linux setup with Squid connected to the network with the gateway 192.168.23.254. The WRT150N has a gateway of 192.168.23.1. The WRT150N is also connected to an Apple Base Station which serves as the Access Point for WiFi users.Squid limits access for IP addresses listed under the .254 gateway. But once I change my gateway to 23.1, everything is accessible. I want to block sites as well on the WRT150N. But every time I try to put a new Access Restriction, it doesn't work.
View 4 Replies
View Related
Jul 28, 2012
It has happen suddenly : Internet is not working through WRT150N, though it work when directly connected to the modem. So I think it is a router issue :On the WRT150N, Internet light is flashing fast for 2 seconds, then is off for 2 seconds, then flashes, then is off and so on, wether there is a device (computer, modem, ...) plugged or not, through the blue ethernet connector.And sometimes, Internet light stays off from power on, whatever is done with ethernet connexions (yellow or blue).
When connected to the blue ethernet Internet connector, my pc ethernet lights don't blink (nor the link light or the data light)I have try the 30-30-30 reset cycle. But it doesn't improve.I have tried the loopback test : connect an ethernet cable from the one of yellow ethernet port of WRT150N to the blue ethernet of WRT150 N.Sometimes, the light for the yellow ethernet port goes on for a few seconds, while the Internet light continues to flash. After a few seconds, both go off.Sometimes, as soon as the loopback is made, the 2 lights go off, and if a computer is plugged to the yellow port, the ethernet lights of the computer and the router stays off.But I can access to WRT150N through Wifi and I can access to the web management.
View 7 Replies
View Related
Oct 31, 2012
Several "consultants" have told me that the problem probably lies within my Linksys WRT150N.However, upon pinging the router, it responds. I did not reset the router to factory default), I just pinged it, and it's there.My firmware is v1.0.04. My provider is Cox Communication, and the connection os cable modem.Curiously, my wife's I-Pad will not open these links either.Sample link that doesn't work: url... Upon website opening click on "weekly ad".
View 2 Replies
View Related
Feb 9, 2008
I had successfully set up my new WRT150N router and it was working. But then it just stopped after about 12 hours. All the lights on the front of the router are blinking. When I directly connect to the router, my computer can't detect it. I've browsed through these forums a bit and tried a few things - the reset button (60 seconds), unplugging the router, downloading the EasyLink Connect tool, but I'm still stuck.
View 5 Replies
View Related
Jul 10, 2011
I've been using a WRT150N wireless router successfully up until a couple days ago, when it stopped being detected. I can plug my computer directly to my modem, and it works, so my internet connection is fine. I have an older BEFW11S4 router that I am using currently, but it is very slow compared the the N router. I've tried resetting the 150N router, and also the modem, and combinations of both, but nothing seems to work. I plugged the router into my computer without connecting the modem, but I'm not able to access 192.168.1.1 either. All the lights illuminate when the router is plugged in.
View 9 Replies
View Related
Jan 9, 2013
I have been using d link routers for a very long time. However, recently I have a problem with one of my dlink router..
Basically I have a Wireless N 150 Home Router (DIR-600 B2). I managed to reset and login to the router at http://192.168.0.1. I tried to made some configuration (disabling DHCP, some stuff, basically I was trying to configure this router as Wireless Repeater to connect to another room downstairs).
So it didn't connect so I do a reset (hold a pen for 20+ seconds at the reset button) and now I cant login to the router at http://192.168.0.1..
View 4 Replies
View Related
Jan 21, 2008
I purchased a WRT150N in early Dec 07. I had a number of problems with the unit disconnecting from wired and wireless connections erratically anywhere from 1/2 hr to 10 hrs. of operation. Troubleshoot thru Linksys chat. Ended up replacing router. Now I am having the same problem with replacement router. I've updated my windows XP, SP2, updated Ethernet driver and manually reconfigured router per Linksys advise. Wife and my laptops have N adapters, primary PC is wired in. It seems to disconnect all connections at same time, totally random. The only way to reconnect is to power down router for a few seconds and then power up.
View 9 Replies
View Related
May 23, 2009
My Linksys WRT150N recently gave up on me and started to give me weird issues and started to disconnect (all the ports including wired & wireless) anywhere from 3 to infinite number of times per day and my only solution was to remove the power chord and connect it. I tried all possible ways possible including resetting the router, stopping SSID broadcast, removing the encryption, etc, but non worked. As the router was out of warranty my only option was to take it to the dealers where they told me it would take 3 weeks to fix and God knows how much they would have charged me. But after flashing the firmware with the dd-wrt it has been almost 24 hours without a single problem and now I have the cool option of seeing who is connected to the router, etc. This is a MUST for every Linksys owner.
1. Reset the router using 30-30-30 and waited for 2 minutes for things to come back 2 normal
2. Flashed the router with "dd-wrt.v24_mini_generic.bin"
3. Reset again using 30-30-30 and wait again4. Flashed the router with " dd-wrt.v24_std_generic.bin"5.
View 3 Replies
View Related
Jan 28, 2012
I have WRT150N, with firmware version 1.01.9 and I can not get the internet access policy to work.Here are my settings: PC list is configured through IP range as follows:Even if I deny internet access completely, I can still access the internet.
View 2 Replies
View Related
Nov 12, 2011
with my Linksys WRT150N router in "N-only" mode, the usb adapter WUSB100 doesn't connect. In the datasheet is written that it is B-G, but also N compatible..[URL] It connects only when the router is on "mixed mode" (B-G-N).
The device works great, the only thing is that it doesn't connect to N networks.... cause i think it is not N compatible. When i look for networks, Windows shows me that there is my N network, but when i click connect, after a few seconds, appears "impossible to connect".... but if i set the router on "mixed mode", no problems.
View 9 Replies
View Related
