Cisco Wireless :: Hard Reset On Ap 1130AG Does Not Work
Oct 17, 2011
I got a problem with a ap that I have here where I do not have the password and I did the process to reset the AP to factory defaults, but the configuration still the same, and the AP still asking for the enable password, its the same problem poused before in this link URL. I did the same process but I still have the old configuration on the AP. I noticed that the AP change the image when I reset the AP, using the mode button. the AP is starting with and rcv image. I need to reset the AP to its initial configuration.
I have a router that I upgraded the firmware a while ago, I stopped using it several months ago, I was going to give this router to my sister, i tried a hard reset(30 seconds press reset, unplug, hold hold the reset, wait 20 sec, plug power, hold for 30 sec and release the reset) and I tried to login with admin admin and it doesn't accept it. I tried with another router dlink 614i and the same problem, after resetting it it's not accepting admin admin log/pass.
I have an EA-4500. Unfortunately I often have to hard-reset it:
- every time I update the firmware (last time I updated to 2.1.38.138827 via Cisco Connect Cloud)
- sometimes whenever there is a black-out
The first time it happened upon the automic firmware update which released Connect Cloud. In such cases, the router stays with the white Cisco logo on and no other lights work (i.e. the ethernet lights on the rear side of the router are off). The only reset procedure working is: unplug Internet cable, press reset for 30 secs, turn off while keeping reset pressed, wait 30 more seconds, turn on again always keeping the reset pressed.
I've tried to turn off for 2 minutes but it doesn't work. The strange thing is that the above reset procedure does not always work, sometimes I have to do it like 10 times before the router Cisco logo light starts blinking on and off (like breathing).
Besides this, which is very very annoying, I'm satisfied with router functionalities and performance.
I have an e4200 with the latest firmware 2.1.39. I just upgraded the firmware due to connection issues with my DSL. I now have the same issues with disconnects but I believe they are being caused by a different issue. When I try and log into my router through the IP address it wont let me, it says it can't find the router. Eventually after getting in the first time by using the default password, I have twice found out that all my settings are gone. This has happened twice this week and only happened after upgrading the firmware but I can not tell if firmware is causing it or if it is hardware related. I now reboot and restore saved firmware but that is a hassle and am pretty sure that is not the way it was designed to work.
Purchased desktop from micropro in 2002. We finally upgraded to cable internet in 2011, Wife purchased Think Pad laptop also in 2011 (wireless enabled). Purchased Belkin wireless router and want to network these 2 computers.1. My desktop has been demoted to the garage. I have wiped it clean (i hope) by doing a reinstall of XP Pro. Now some of the USP ports won't work. How do I network these two machines?
I recently rescued an old Belkin 54G router (Model: F5D7632-4) which I planned to use as an extra wireless access point towards the back of my house where I have some dead spots. I logged in on the Belkin's IP: 192.168.2.1 And went straight to change the IP and put it onto the same subnet as my router. I changed it to: 192.168.0.1 as I had it in my head my router was .254 My router is 192.168.0.1 so obviously this didn't do much and I couldn't access either device.
I unplugged my network and plugged directly into the Belkin to change to another IP and I cannot access it. The operation times out. I can access the normal router when I connect back up to the network fine. To solve this I decided to reset the router. The instruction manual for the Belkin says a momentary push on the reset will do a quick reset. while >20 seconds will perform a full hard reset. Both of these are signified by the power light flashing, and the reset is complete when the power light becomes solid again.
Unfortunately no matter how long I hold the reset button for, the light does not even blink and no reset happens. Obviously this may just be a dodgy reset switch, the router is getting quite old, so I will go in an short the reset pins by hand if I need to. The solution I am looking for is either to reset so I can start again - or obtain access to the router through some other means to change the IP and carry on. When I connect the Belkin to my network, the router cannot see it connected to it's Ethernet port. However the Belkin's link light occasionally flickers.
I have a DIR-655 (HW rev A2) that has worked mostly fine for a long time. Today I decided to do a firmware upgrade, and in preparation I backed up my custom config settings and did a hard reset via the factory reset button on the back of the unit.
Since then, the unit itself has been inaccessible from my computer. If I connect the DIR-655 and a PC with a network cable, the appropriate light goes on on the front of the router, but the client does not lease an IP address from the router and I can't access the router home page at 192.168.0.1.
I have tried the reset button again and also power-cycled multiple times, and I have tried connecting from multiple computers, all with the same unsuccessful results. how to "un-brick" the device?
I have a belkni F5D Router and I have lost the password to access it. I dont have any computers or devices that still connect to it, and I really need to know how to hard reset the password!
Region : Others Model : TL-MR3420 Hardware Version : V2 Firmware Version : openwrt-mr3420-v2-HM2013-04-19 ISP : Cellcom Israel
how to make hard reset to MR3420.I installed openwrt-mr3420-v2-HM2013-04-19 software to my router.and after that while the router restart the led green lights flashing on and of all the time.and I cant contact to the router with wifi or lan cable
I have a WES610N in my office connected to a E4200 @ the cable modem in the family room. ~30'.The connection is fine and works well when working.Connected to the WES610N I have:
-Polycom VOIP phone -HP Mediasmart Windows Home Server -Desktop -Multi-Function Laser Printer
I have two issues.
1) The Polycom does a random reboot that I have traced down to it loosing it's IP 2) The Windows Home Server looses it's IP requireing a hard reset.
I have enabled QOS for the polycom and that just worked with managing data. However both devices seem to loose their IP regularly. The desktop might also be having the issue but because it is Vista I suspect Vista is better equipped to deal with IP issues.
We have an AIR-LAP1142N-E-K9 deployed in a H-REAP setup.This AP already got the configuration from the WLC when it was deployed at a remote site.Now we moved it to another site, but it doesn't appear in the WCS and i don't see any CAPWAP debug messages on the WLC.The routing work fine between the AP and the WLC, the AP also gets an IP address from DHCP and also received Option 43 information.
Now my guess was that the AP doesn't associate with the WLC because it has the old config file and it runs in local mode(without trying to connect to the WLC).We want to reset to factory defaults because we want to delete the configuration and force the AP to get a new config from the WCS.I don't know the enable password so i had to use other methods for reseting to factory defaults.
I tried to use the information from here:[URL]I used the "MODE button":I get the following message from the console:
"button pressed for 5 seconds process_config_recovery: set IP address and config to default 10.0.0.1"
So just recently my Internet has been running a lot slower than normal at different times of the day (completely random, could be fine for hours then just turns slow). I know it's not the Internet itself, since it's only happening on my computer, and none others in the house - and I'm far from capped. I've run AVG, Spybot & Malwarebytes' scans and have found no infections of any kind. I've run TCP Optimizer and used the "reset to windows default settings" feature, which also hasn't worked one bit. I've tried different Ethernet cables and different plugs in the modem and no improvement.
I have a couple 1130AG switches. I'm trying to pull an image file from the flash on a Cisco Air AP1131AG. The file is c1130-k9w8-mx.124-23c.JA4.tar. The issue that I'm seeing is, I do not see a copy command to go through the tftp process. I've tried to use tftpd32 and enter the IP of the AP as the remote host, but that is not working either. Do I need to connect an ethernet cable straight to the AP in order to use Tftpd32, or can I use a console cable?
I am trying to join my 1130AG-E-K9 AP to my 2016 WLC, but it is stuck in a boot loop and will not connect to the controller. [code] I found some details here: url... but I'm not sure what it means that I have a 'SSC AP'. I am not local to this AP, though I do have a console connection to it-what do I need to do to get it working again? It just continually goes through this error and reboots every 30 seconds or so, so it's useless at the moment.
I'm trying to set up this 1130AG with a private wireless network and a guest wireless network. Initially it had just one wireless (private) and it worked fine, but then when I created the two VLANs for each SSID and then the guest SSID and now the guest SSID is visible/broadcasting, but the private SSID has disappeared or is off.
P.S. - It's a Cisco Aironet 1130AG (AIR-AP1131AG-A-K9) running 12.3(8)JEA system software and I'm using the web GUI (I'm not familar with the command line for Cisco products yet).
I have multiple cisco 1130ag access point at one of my clients villa. The issue I am facing is when moving throughout the buildingthe laptop and smartphones will not switch between AP’s unless it loses its connection with its existing AP then it will see the other AP that is closer and connect to it.
For example, I start at one end of the building where it connects to AP#1 , if I then slowly go to another section of the villa, it it will not switch over to AP#2 until the signal is lost from AP1
I have following settings
AP's are Cisco 1130AG Single SSID with WEP Security
i have installed ISE1.1 on VM and other hand vWLC7.4 also there in VM i am using 1130AG APs in flexconnect mode and using central auth and central switch.i wan to configure it for CWA(central web Auth) from ISE but a little a bit confuse about ACLs.
I am trying to find a way to login to our wirless access point. I have a Aironet 1130AG series wireless router. I have the ip address. It is a POE device so i dont have a power supply for this device. When it is on I can see the Wireless Network but the passcode has been lost and no one knows it. Is there a default IP address for this equipment? There is an Ethernet port for a console but without the power supply i cannot access it.
One of my Wi-Fi site, having cisco_1130AG access points nearly 110nos as of now i installed 80nos, after installing, in out off 80nos nearly 12nos of APs's radio is showing down.
Again i reset and re-configure then it is working fine, is there any readio (802.11g/a) problem in this model?
I have 1 EuroDocsis modem and 2x 1130AG wireless things.How do I manage to get this connected to each other wirelessly?The internet is allready configured at the EuroDocsis modem and I now want to distribute it wirelessly to both 1130AG's. The EuroDocsis is using WPA2 PSK.I read something about WDS, but I don't get that to work either.
I have a Problem with a customer WLAN. The customer has a Aeronet 1130AG AP. Now i should configure a Aironet 1130 Repater for this WLAN. The initial connection from the Repater with the AP is no Problem. But after some time the Repeater lost the connection. On the AP i see following Messages:20Jul 19 19:05:28.061InformationInterface Dot11Radio0, Deauthenticating Station xxx Reason: Previous authentication no longer valid 21Jul 19 19:05:28.061WarningPacket to client xxx reached max retries, removing the client 22Jul 19 16:43:59.412InformationInterface Dot11Radio0, Station yyy Associated to Parent xxx23Jul 19 16:43:57.901InformationInterface Dot11Radio0, Deauthenticating Station yyy 24Jul 19 16:43:56.536InformationInterface Dot11Radio0, Station yyy Associated to Parent xxx 25Jul 19 16:43:51.555InformationInterface Dot11Radio0, Station zzz Associated KEY_MGMT[WPA PSK] 26Jul 19 16:43:29.078InformationInterface Dot11Radio0, Station Repeater01 xxx Associated KEY_MGMT[WPA PSK]
We have a guest wireless network using 1130AG Access Points. Is it possible to allow devices on this network access to an Internal IP? I know that kind of defeats the purpose on the guest network, but we'd like to give access to internal email to these devices. Currently this does not work because you cannot loop back into the network to gain access (out the firewall and right back in the same port).
The 1130ag was the LAP model but I upgraded it to run in autonomous mode. My understanding is that it cannot assign IP addresses but I just want that confirmed. It is not connected to a WLC nor a server that can do DHCP.
How can I enter into "interface configuration" on Aironet 1130AG, AIR-LAP1042N?When I put following commands in enable conf tinterface Dot11Radio1 but, it fails and I cannot enter into "interface configuration".How can I do this ?The reason why I enter into conf tinterface Dot11Radio1 because I want to disable cdp via CLI ( serial console).
we just deployed a cisco wireless solution with WLC4404-100, WCS, and a bunch of 1130AP and I experience some problem with file copy under windows xp. The file copy is working fine with my Ethernet connection however.The symptom is as follow. I cannot copy large file from a share to the computer. The copy starts then after a while (let's say 30MB copy over a 100MB file) it stops with the error 'File copy error: The network name is no longer available'. When this occurs, I still have my wireless card connected and I can ping my computer from the controller.I tried to adjust some radio settings (channel, power on the AP I'm connected to) because we have a large wireless network here, but no success. I also update the wireless card driver, create a new SSID, etc. No success at all. However the copy went fine for small file size.
Several 1130AG AP, auto IOS, are showing the same three errors;
1. 'Error' Interface BVI1 Changed to up 2. 'Error' Interface Fast Ethernet0 Changed to up 3. 'Error' Interface Dot11Radio0 Changed to up
ATTACHED image
Why these interfaces coming 'up' would be an 'error'? Seems almost like hardware failure/s. So we have been investigating on several 1130AGs bought from different places, with different configs and still get the errors. The APs appear to 'work' (i.e. basic config, wireless working, clients assoss., data flows to internet and back through APs) but the error causes the event log to show 'error' and for the status LED to turn 'yellow', instead of 'light green' (light green when working normally and no clients assos).
I have worked with many cisco APs and never ran across these two errors.
At first I thought it was a power issue, as the AP will boot up in low power if it doesnt think it's getting enough power, which could cause the IOS error possibly. But all of our APs are powered by wall plug cisco 48v OEM plugs, no POE injectors or switches. We even changed the settings in power of the IOS to 'pre-compatiable' POE and similar and still recieve the error and yellow LED status light. We looked into this power issue because we wanted to rule out if these was what was producing the errors that were reporting.
The second thing we did was setup the test APs with a very basic config, one ssid, no security, as to rule out a config error and also, no config will make the radios disabled, so without a basic config the APs cant be tested anyway (since the radios are now disabled from default). so we tested very basic configs and still getting the error and yellow LED (which all manuals say it should be light green normally working and no clients). all config changes brought wireless up and we can connect clients and data flows but still the errors stay and yellow LED once all clients disconnect. Note; when clients connect the yellow LED turns to light green, but thats not the colors the manual states they should be which is odd).
Third, a couple engineers suggested this error was from the AP scanning channels to choose the least congested (default config) and it will pick a channel but produce this error still and go yellow. We changed the configs to the least congested channels and it reboots and still gets these errors.
We have tried several IOS software packages, some newer, some older, all auto. though, no LAP.
We googled the errors but could only find ONE post with these errors. Some engineers said these errors are 'normal' and they have seen them before, but theres nothing on the web about the errors and we have owned 20-40 different cisco IOS APs and never seen this, and we have the same issues with 4 1130AGs, all in almost new condition, bought from different places.
Unless you have opened a 1130 many people dont know the status LED is actually 3 LEDs (one assembly with 3 micro LEDs, blue, green and red) that combine in color (the micro LEDs light up in different intensities causing many final color combintations), and the LEDs colors mix together via a plastic light guide on the top to show the status LED, and we believe the error is causing the status LED color to be off because the error is making the yellow light up and mix with the other colors causing all the other colors to be incorrect. we have researched trying to clear the error by 'clear logging' CLI command, hoping that may clear out the interface error and turn the yellow LED off because there would be no log of the error, but we have not succeded.
I can not get this to work.I have 1 EuroDocsis modem and 2x 1130AG wireless things.How do I manage to get this connected to each other wirelessly?The internet is allready configured at the EuroDocsis modem and I now want to distribute it wirelessly to both 1130AG's. The EuroDocsis is using WPA2 PSK.
I have installed an Aironet 1130AG and utilized a power injector for the power source. I have the settings configured correctly in IOS, but the AP takes about 7 minutes to come on (illuminate LED status lights) once the Ethernet cable is connected. Is this 7 minute power-on delay normal when using POE? I am used to the instanteous "on" that usually comes with Cisco products being connected directly to the AC adapter.
