We have a guest wireless network using 1130AG Access Points. Is it possible to allow devices on this network access to an Internal IP? I know that kind of defeats the purpose on the guest network, but we'd like to give access to internal email to these devices. Currently this does not work because you cannot loop back into the network to gain access (out the firewall and right back in the same port).
View 5 RepliesI have been trying to create a Guest WLan on my 4402 WLC system and have found several confilcting documents explaining the procedure. During this process I have notices that although the current corp wireless works, there was never a virtual interface created for it. Instead it uses the same Wlan/Vlan as the ap manager and managemnt interfaces. Could this by why I cant seem to get the Guest access working? or is this not a problem after all since the wireless does work.
View 1 Replies View Relatedi have two WAP4410N wireless router. with software version (2.0.1.0) , here i have a problem on SSID broadcast and access.i have created Two ssid's WC72 and SREE with same security configuration WPA2-personalmixed . i cant see the broadcasted SSID of name SREE where i only view WC72 and get connected to it..
where i initially want is separate SSID and internal network access for internal employees and Guests (shouldn't connect to internal network).
We have a Cisco wireless infrastructure in place that includes a guest network with its own subnet that is a sub interface of the inside interface on our ASA 5520. There are no routes for it to be allowed access to the internal subnets. So it can only access the internet. This is primarily used by the public, but we have several non employee personnel that we only want to give internet access and force them to access the internal network through our clientless SSL vpn portal or through other internet facing internal resources such as webmail.I have done packet traces from within the ASA and the break appears to be there is no ACL allowing the traffic back into the network once the web resource replies to the request and the traffic is attempting to come back into the network from the web resource. Is that as clear as mud?
I know that this has to be a common problem and a way around this is to allow the guest wireless network access to the internal network but only for the select resources that they require. And that this can be done seemlessly by network specific routes and or alternate DNS entries, but I would like to keep this simple and just allow them to access the web resource, webmail and VPN, from the guest wireless using internet DNS servers without route trickery.
I have created a new sub-interface on our ASA 5520 for guest internet access.
My goal is to allow access to a few specific services hanging off some dmz interfaces on the same firewall and full unrestricted access to the internet only. Everything else should be out of bounds.
The order of the rules I plan to setup on the guest interface inbound are:
#1. <rules to allow access to specific services in the dmz>
#2. <block any ip access to the entire private network ip address space>
#3. <permit ip any any>
#1. These rules will give access to the guest user to services located in the dmz
#2. This rule will block all access to any services in the private ip address space (thus blocking access to all internal services)
#3. This rule is to allow access to any other services i.e. the internet.
Is this the best way to achieve my goal in the most secure way or is there a better way? i.e. is there a way to force the traffic by default to only go out the outside interface unless there is a specific rule allowing it go elsewhere?
(Of course Dynamic PAT will also be configured for traffic coming from the guest interface to the outside interface.)
I recently purchased the E2500 cisco router. How does the MAC computer be able to log in as Guest user to access internet?
View 2 Replies View RelatedI have the syntax correct and thought process down right on a solution to allowing guest wireless users access to an internal webserver. (DMZ discussion aside)
We have an ASA5510 with interfaces setup as:
outside - 65.x.x.x address
inside - 172.20.1.2
guest_inet - 10.2.1.1
Internally clients resolve our website to 192.168.40.40 and that part works as it should. Clients outside of our network resolve our website to the correct external address (lets just call it 1.1.1.1). We have a NAT statement static (inside, outside) 1.1.1.1 192.168.40.40 netmask 255.255.255.255 and an ACL to permit tcp any host 1.1.1.1 eq www
Clients on our guest_int use an external DNS server and hence resolve our website to 1.1.1.1. However it seems traffic goes out and back in our outside interface and this connection never occurs.
What I'm wondering is the correct NAT statement / ACL to add that would allow our internal clients on the 10.2.1.x network to access our internal website. Would that be: static (inside,guest_inet) 1.1.1.1 192.168.40.40 netmask 255.255.255.255 ? Since there is already an ACL permitting port 80 traffic to 1.1.1.1 we should be taken care of on the ACL side of things, right?
How would I configure a "guest" wireless network, with a different key/password, that uses a different subnet than the existing network?
We have a simple 192.168.1.x subnet currently, with the Aironet as our only AP. The Aironet support a "guest" wireless function, but how do I make that work with the RV180?
Is it possible to allow certain websites to bypass the web authentication pages, so that they do not need to authenticate to get to our own website, but do have to if they wish to go anywhere else?Looking at a 5508 model at the moment
View 4 Replies View RelatedCan we change the internal web authentication for guest network to use http instead of https?
View 3 Replies View RelatedHave a WLC 5508 running 6.x code with LAP's providing wireless for our internal laptops (WPA2 and EAP-TLS). I want to provide guest wireless which goes out a different port on the WLC to a guest firewall/cable modem. However, we want to prevent our internal laptops from being able to use the guest wireless. I have RADIUS (IAS) and LDAP for my AD available. We would prefer not to have use Lobby Ambassador and just have the guests use a simple password or web passthru. Guests may be laptops or smartphones. What options are available? I have tried a test setup using dynamic vlan assignments from RADIUS using the IETF flags, but can't seem to get it to work. Is there a way to identify the SSID is being used at the RADIUS server?
View 13 Replies View RelatedI have multiple cisco 1130ag access point at one of my clients villa. The issue I am facing is when moving throughout the buildingthe laptop and smartphones will not switch between AP’s unless it loses its connection with its existing AP then it will see the other AP that is closer and connect to it.
For example, I start at one end of the building where it connects to AP#1 , if I then slowly go to another section of the villa, it it will not switch over to AP#2 until the signal is lost from AP1
I have following settings
AP's are Cisco 1130AG
Single SSID with WEP Security
I have a cisco wlan controller (2100) running software 7.0.235.0. I have the internal private wlan running off of port 1 and that is working fine with an internal dhcp server.Is it possible to setup another ssid (guest) and have the interface directly linked to a static ip on the WAN and also use the built in cisco internal dhcp server?
View 4 Replies View RelatedI am trying to find a way to login to our wirless access point. I have a Aironet 1130AG series wireless router. I have the ip address. It is a POE device so i dont have a power supply for this device. When it is on I can see the Wireless Network but the passcode has been lost and no one knows it. Is there a default IP address for this equipment? There is an Ethernet port for a console but without the power supply i cannot access it.
View 3 Replies View RelatedOne of my Wi-Fi site, having cisco_1130AG access points nearly 110nos as of now i installed 80nos, after installing, in out off 80nos nearly 12nos of APs's radio is showing down.
Again i reset and re-configure then it is working fine, is there any readio (802.11g/a) problem in this model?
A query here with regards to Wireless isolation between SSID and wireless isolation within SSID.If we have 2 SSID, eg. InternalSSID, GuestSSID on AP1.Both SSID are set to Enabled for isolation between SSID, and within SSID, that would mean all machines connected thro' this AP1, would be isolated from one another.
1) If there's 1 laptop that connects to another AP, lets call it AP2, (doesn't have isolation function) on ssid01. Would this laptop still be isolated from those that connects to the first AP?
2) If there are wired PCs connected to the router. And the 2 APs are connected to the same router. Would the machines connected thro' the AP1 on either InternalSSID, GuestSSID be able to access those wired PCs? (My assumption is yes.)
3) Is there a quick and efficient way to setup on WRVS4400N to isolate GuestSSID totally from InternalSSID, and wired PCs. InternalSSID and wired PCs should be allowed to 'see' one another.
The challenge here is that, the network points are all installed already. Both AP are connecting thro' 2 separate unmanaged switch together with a couple of other PCs. 1 Port on the unmanaged switch, each,connects to the router.
I currently have a sagem router provided by my isp (sky), as the signal does not reach all areas of my premesis and sky refuse to let me use my own router I decided to purchase a wireless extender. I got a Edimax EW-7416APn and configured it using the following settings at the following address:when I connect to the extender i can gain access to the management settings, if i perform a scan using the extender it can see the original router, if I check the security settings they hold the correct ssid, security type (wpa - tisk) and the correct passphrase.
View 1 Replies View RelatedI bought the router E2500 and I followed the steps for its configuration. It so happens that most of the time I turn on my router, it does not connect to microcomputer, because it loses the internet settings, requiring that I turn the CISCONNECT and after that, I have to turn off the microcomputer, wait for 2/3 minutes and then reconnect, for only then will be able to surf the internet. I notice that many times even I doing all this procedure the router does not give access to the internet. What should I do?
View 1 Replies View RelatedJust recently got a Zyxel VSG1432 router connected to the main computer in my home. I am now trying to connect my laptop wirelessly. It will connect to the router but says it is an unidentified network and it doesn't connect to the internet. There is an x in the network and sharing window.I have tried restarting the router, going to the router webpage and resetting to factory settings, none of this worked. Also contacted the service provider and spoke with two tech guys, but still no luck.
View 1 Replies View RelatedIn our Environment we used to Connect to wifi using Radius Authentication Through AD Account (Encryption: TKIP and CIpher, Authentication Open+EAP and Network EAP, Key management WPA) this settings which will be done And pushed through AD Itself.We Use CIsco 1130AG, 1200 Series in most of the areas which have no Issues.But We Have Some trouble with Cisco WAP4410N Access point.In This Access point users were not able to Connect to wifi through Radius Authentication.However users were able to Connect to these Access point, but it is unsecured, whoever configure's the correct client settings in their PC. They can connect to SSID. This Access point is capable of supporting Radius Authentication?
View 4 Replies View RelatedRecently a router crashed and some suspicious about the client arised. The point is that now the order is to deny all kind of router admin access for the client. I was thinking, is this a good idea or will be better to give him limited access to the router, to avoid the client to try to access the router at all cost? Something like to stop the motivation to crack the router password.
View 7 Replies View RelatedI have two SSIDs on an Autonomous Access Point, that goes to a 2960 switch, that connects to a L3 3560. I have a vlan for admin/private internal access that uses the native vlan (1) and guest vlan (50). I have configured both and I am trying to get both to go out the same Internet connection.
I cannot get the guest access to access the Internet. It looks like my computer will go, but it just comes up saying no Internet access.All interfaces are trunking this vlan properly. I can communicate from the laptop to the 3560 but I just can't get to the Internet.
I want to give access to remote subnet on firewall 5505.
Remote subnet is 16x.15X.56.0
Here is my access list
access-list outside_5_cryptomap extended permit ip 192.168.12.0 255.255.254.0 16x.15X.56.0 255.255.254.0
I am implementing a guest wireless network to work alongside my internal network. The guest network will use the existing switching network and will be separated by VLANs. I have the ASA set so that traffic can get to it and out to the Internet. I can set up a workstation on the same VLAN as my guest network and can route inside my network (strictly doing this for testing purposes). Where I am having problems is with the Catalyst 4506 switches and the ip routing. I had two separate "ip route" statements defined on my switches.
ip route 10.200.2.0 255.255.255.0 10.200.2.254
ip route 0.0.0.0 0.0.0.0 10.100.100.254
I have discovered that the traffic is always following the default route despite the fact that my IP address on my test workstation falls in the 10.200.2.x network. I was looking at documentation and found that it is possible to set up policy-based routing on the core switches. Can you have two "ip route" statements defined like this to segreate traffic or do I have to use PBR for routing (or a combination) in this case? If I define PBR then how does that impact my existing routing? I need to make sure that I can still route the existing traffic while I'm configuring this change.
I understand you can have a guest wireless setup on the newer Access Points, and trunk (cisco term) the 2 VLANs and seperate them out with Access Control Lists so they don't talk to each other, but I would rather just give the VLAN 480 it's own DHCP from the router.
[code]...
Is it possible to provide wireless guest access over the WAN from another office via the WLC. I have WLC 5508 in a central office and have other remote offices that have one Access Point in each office that are autonomous; I will be converting these to LWAPP. Is it possible to route guest traffic back to the WLC then forward this traffic out to the internet? How would I route this traffic out as well? install a secondary WLC in the DMZ and use anchor points. I only have one WLC
View 7 Replies View RelatedIt's my intention optimize our business WiFi network.Actually we don't have a "Guest" access.Probably WAP321 should be the best solution for us.We will need 3 WAP321 to cover offices area.I have different questions/doubts about Captive Portal functionality.using 3 different WAP321 everyone has the "captive portal" feature, or you can configure only one of the three the feature of "captive portal"?if is possible to configure only one of three the feature of "captive portal", the others WAP321 trusting the authentication?what is the ip address released from the "Captive Portal"?all Guest user have the same username and password?
View 1 Replies View RelatedWe have a 2106 that was configured by a former employee. No one left in the company is qualified to configure it. The wireless guest access used to work fine. We'd configure a guest user account. They would connect to the guest wireless, open a web browser and login. For some reason now there is no prompt for login. People can connect to it and get an IP address, but that's it. No login prompt or anything else from there.User Login Policies was set to 0 and I put it to 8. That didn't do anything. Under Web Auth > Web Login Page it's set to Internal (Default).
View 5 Replies View RelatedI'm looking to implement guest WiFi access with web authentication on one of our 5508 WLC (currently deployed within a sandbox environment), but looking for some assistance. The WLC currently has a single connection from port 1 to the 'Test Site 2' switch. This is a dot1q trunk. On the WLC, the interface (for port 1) is configured as follows: [code] Currently, I have one WLAN configured with the profile name 'Guest Test 1', it's enabled and broadcasting the SSID. Security is L3 only with web authentication configured. The WLAN is configured to use the interface names "guest_wifi".
The issue is that when a client connects to the WLAN, it receives an IP address okay (10.99.254.x address), but doesn't seem to be able to contact the WLC to get the web authentication page. Eventually, the WLC terminates the connection due to an authentication failure.does it sound like I'm taking the correct approach here? The idea is that clients connect to the guest WLAN, which puts them on VLAN 99 and routes traffic through to the ASA and then onto the internet.
I currently have two AP541N access points. Both are configured for internal access and one unit is configured with a Guest VAP. I want to configure the Guest VAP to redirect to an authentication page so that the user connecting has to log in to get internet access. I'm fairly certain the AP541N doesn't offer this out of the box. I know I can redirect, but what is needed to force a user to authenticate to gain internet access. I want to find out what additional hardware/software I will need in order to create Guest Services of this VAP.
View 1 Replies View RelatedDoes the Linksys AP (WAP4410N) support Wireless Guest access solution?
View 2 Replies View RelatedIn the ISE documentation is states that under a Guest_Activity report you must have guest access logging enabled on the NAD in the ISE network. My question is where do I enable guest access logging in the WLC that is our NAD?
View 1 Replies View RelatedI just got a new requirement for our wireless roll out and I need some help. Plan the best way to provide employee and guests wireless access w/ the guests separate from the production environment.
We have a 5508 controller w/ 1142 APs. I have two GBICs in the interfaces (only one is being used). I want to use a back haul connection for the guest access. I am having a hard time in visioning how to physically set up the cabling from the patch panel. Again, the requirement is to not allow guest users to connect to our production network but I still want/need to manage the AP. This will eventually need to be supported for remote sites tunneling back to the primary location.