I want to give access to remote subnet on firewall 5505.
Remote subnet is 16x.15X.56.0
Here is my access list
access-list outside_5_cryptomap extended permit ip 192.168.12.0 255.255.254.0 16x.15X.56.0 255.255.254.0
I have a network with 3 sites that are on different subnets. Each site has an ASA Right now, I am only able to connect to the ASA that is connected to the subnet I am connected to.I want to be able to connect to the ASA that are on the remote subnets on the address of the inside interface.The sites are connected all together by site-to-site VPN.Is there any way I can achieve that without opening the outside interface directly on the Internet?
View 2 Replies View RelatedI have a remote ASA5505 running 8.4(3) with a working site 2 site VPN tunnel to my main office. (The main office is running an ASA 5510 with OS 8.4.3 as well). The encryption domain is all private IP on main site vs. 172.16.10.0/23 on remote site.
Relevant config of the remote ASA:
interface Vlan1
nameif inside
security-level 100
[Code].....
I can manage the ASA on the outside interface (outside of the site 2 site VPN) using the TACACS credentials I can also ping my management station from the ASA using the inside interface, but as stated, the other way around does not work. I have not yet tested if management from the local 172.16.10.0/23 subnet works, but I will try this next.
How do I enable remote access to ASDM from outside of the network on the ASA 5505? This would be used for remote access to the firewall at a site that is not utilizing VPN.
View 5 Replies View RelatedI would like to allow remote access to a windows server through a ASA (5505) firewall. Users will use the vpn connection in order to connect to a private network. Is there any link that describes the steps for ASDM?
View 3 Replies View RelatedASA 8.3(2) 5505
I've configured a number of remote access vpns on ASAs, but I don't recall having a default gateway setting assigned after logging in.
Is there a way to disable the assignment of a default gateway upon login?
The value assigned is meaningless. It's just the next available address in the local pool.
I have been asked to set up remote access VPN on an ASA 5505 that I previously had no invlovement with. I have set it up the VPN using the wizard, they way I normally do, but the clients have no access to anything in the inside subnet, not even the inside interface IP address of the ASA. Thay can ping each other. The remote access policy below that I am working on is labeled VPNPHONE, address pool 172.16.20.1-10. I do not need split tunneling to be enabled. The active WAN interface is the one labeled outside_cable. [code]
View 1 Replies View RelatedI am proposing Remote access VPN solution to my client as per the attached diagram. However they are required IPS solution as well.
So in this case i dont think i can implement the IPS with outside interface in inline mode because of the encrypted traffic. Is it feasible if i enable IPS with inside interfce ?
After getting hacked I want to limit terminal server/ remote desktop to only my computer. (although I may need to let other net in later)
In other words I want only computers from my home ip range (lets say my ISP gives me at home something in 28.28.XX.0) to be let in to the router at work and then to port 3389.
In the work ASA 5505 softwareVersion 7.2(4) I now have:
access-list outside_in extended permit tcp any interface outside eq 3389
static (inside, outside) tcp interface 3389 192.168.1.2 3389 netmask 255.255.255.255
acces-group outside_in in interface outside
I am using two firewalls to connect two different offices. Firewall 5510 is running ASDM 6.3 and 5505 is running ASDM 6.2, Problem is that even after connecting two sites, i am unable to ping remote network from either side. I am mentioned static route as tunneled.
View 1 Replies View RelatedBased on my diagram, my computer A (192.168.100.11) can ping and access my computer B (192.168.10.14). But, when i'm home and i use remote access vpn (192.168.200.x) in cisco asa 5520 to connect to my computer A is okay. But, when i try to ping my computer B is not okay. I already do the exemption for 192.168.100.x and 192.168.10.x in nat rules for inside interface (192.168.100.2) ...
Should i put routing from outside 1.1.1.2 to 192.168.10.x by using 192.168.100.1 as a gateway?
Main Site allows communication from Remote Site via VPN to Windows ServerMain Site also has a secondary subnet that communicates ONLY through internet but NOT to the Windows Server.Sonicwall 192.168.168.x is main siteRemote Site is 192.168.0.x connecting to Main Site to access shared folders on serverSecondary subnet at Main Site is 192.168.0.x using Windows XP PC's. They are accessing a linux server at 192.168.0.215 which Main Site has no access to.VPN remote ip's are 192.168.0.x - they can successfully access the Windows Server at 192.168.168.100 BUT NOT 192.168.0.215.GOAL: Want to connect Remote Site to Secondary subnetWilling to make router changes or whatever is necessary to get Remote Site to access Secondary Subnet with the only exception that the Secondary Subnet REMAINS.VPN DHCP is turned off but willing to turn it on.Willing to make the Linux Server 'discoverable' on the Windows Server. Don't know linux at all but another co-worker set it up and can make changes.
View 4 Replies View RelatedI have a weird problem which I have already submitted a TAC ticket about. When users authenticate through AnyConnect into our HQ ASA 5510 they grab an address from 172.16.254.x. What we have been noticing intermittently is that when logged into our network through the client they are unable to access their resources at one of our remote offices which is connected over l2l to the HQ ASA. This problem just started randomly a week ago and we have been working with Cisco trying to create a solution.
My quick fix is logging into a device at the remote office which is trying to be accessed and pinging the gateway of the virtual subnet for AnyConnect users. When I ping 172.16.254.1 it goes through after a few dropped icmp packets and then the issue is resolved for about 8 hours or so.
We want to use an ASA as a pure routing device. Our network has several internal subnets (10.1.x.0/24), and we want to be able to reach them from outside and to allow access between them.
We have a defined a VLAN for each subnet range with the same security-level, added it to an Ethernet port and made the Ethernet that acts as outside as a trunk, and defined it as the global routing.
We cannot ping any of the subnet IPs defined in the ASA from outside nor we can ping it from the internal IP addresses.
Configuration:
: Saved
:
ASA Version 8.2(1)
[Code].....
I have been tasked with replacing our company eSoft router with a Cisco ASA 5505 with the upgraded security license. I have been working on the configuration for a couple of weeks now, after reading hundreds of forum posts, watching youtube videos, and endless google searching, and despite my best efforts I am still having an issue I can’t figure out.
I have a couple of subnets, that when the ASA is connected, I cannot ping, nor can they get to the internet or our Exchange server. At this point I’m not sure if it’s an access rule issue, NAT issue, or DNS issue.
Here is the network layout:
ASA: 192.168.0.2 (Primary Gateway)
192.168.0.0 (Primary facility, ASA is the gateway)
192.168.2.0 (Second facility, connected via Verizon point-to-point)
192.168.3.0 (Third facility, connected via Verizon point-to-point)
[Code].....
I am working on a site that has recently added a new subnet and I am unable to ping any of the stations on this new network. I have configured an Exempt NAT rule just the same as the rules allowing access to other networks. I have a feeling the problem is in the Site-to-Site VPN configuration since the new subnet is at the primary location over the VPN.
In the site-to-site configuration I added the new subnet to the list of "Remote Networks" and I still can't communicate with any of the devices on the network. If I go to the main site I have no problems so it appears to be related to the VPN or a configuration in the ASA on that site.
A port scan shows that all the traffic is "filtered" so somewhere either the site ASA or the main ASA is blocking the traffic.
I recently installed a couple of Cisco Aironet 3600 Series Wireless Access Points at a remote site. While I was at the site everything seemed OK, The clients were able to get connected to the access points, the guest network worked fine, I could SSH into the access points, and I could ping them. The problem is when I went back to my home site I tried to SSH into the access points through an ASA IPSec VPN Tunnel and it couldn’t find it. When I try to ping the access points they “time out”. I can ping and connect all other addresses (via RDP, HTTP, etc..) on the same subnet which should rule out an access list problem. A couple of notes to be aware of:
The WAP’s have the Autonomous IOS installed (Version 15.2(2)JB) The WAP’s are connected to Dell PowerConnect 5724 (Not by choice.. We are a Cisco shop, these were already there and have plans this year to replace)
I can ping and SSH with Putty to the WAP’s from the local subnet I cannot ping or SSH from a remote subnet to the WAP’s. I can access all other IP’s and Computers from a remote subnet.
We recently upgraded a ASA 5505 with the security plus license to allow us to add a second subnet, but are having a few problems configuring the second subnet. The original subnet we have configured 10.1.1.0 is able to access the internet without any problems. However the new subnet 10.1.5.0 is unable to access the internet and when we ran a trace packet the nat config nat (inside) 1 0.0.0.0 0.0.0.0 is showing as the rule that drops the packet.
Additionally we have not been able to get the 2 subnets to talk to each other even though same-security-traffic permit inter-interface is configured. How to configure the subnet 10.1.5.0 to access the internet or to get the subnets to communicate. Below is a streamlined version of our current config.
!interface Vlan1nameif insidesecurity-level 100ip address 10.1.1.1 255.255.255.0 ospf cost 10!interface Vlan2nameif outsidesecurity-level 0ip address 66.66.66.66 255.255.255.240 ospf cost 10!interface Vlan13nameif corporatesecurity-level 100ip
[Code].....
I'm new to Cisco equipment much more familiar w/ Sonicwall w/ that said......I have a 5505 w/ Security Plus licensing
I have set up multiple VLANs as follows
VLAN 1 inside - still setup as 192.168.1.1 (will not be using this for our lan)
VLAN2 - outside
VLAN100 - LAN 10.1.1.1/24
[Code]....
If I do add all the VLANs above I understand I will probably have to make a trunk port since I only have 5 usable interfaces
I have a cisco ASA 5510 at the branch here. It terminates about 8 vpn tunnels and also it supports remote access clients. I just have a quick question. Can my remote sub-net group access the other remote access site-site VPN subnet group. If yes then how should i configure it.
View 6 Replies View RelatedI have created remote access vpn in my ASA 5505. The tunnel is established but i am not able to access the internal network.
View 3 Replies View Relatedwe are planning on connecting a new aquired company to ours soon?We will connect the remote site to the HQ via a D3. I've been told we will need to have a firewall between them and us for a time. I was thinking of terminating the D3 connection at the remote site of 80 users. Can I use the asr as a firewall as well, to protect the HQ from the Remote site - or should I use a seperate appliance?I was thinking of a asa5505 but, am concerned with bandwidth limitations of the box?
View 1 Replies View RelatedI have created Remote access vpn on ASA 5505 (ver 8.2(5) with base license). When I connect from one machine, I can ping the internal network. But when I connect from another machine, cant.I have only decrypts on the ASA side, without encrypts. I was debugging ICMP packets with the capture feature, and saw that echo-reply packets are returning toward the outside interface, but aren't passing through it.
capture test access-list test interface outside
1: 08:54:44.298980 802.1Q vlan#1 P0 x.x.x.x > y.y.y.y: icmp: echo reply
Where x.x.x.x is LAN and y.y.y.y is the VPN client ip. The nat is ok, access lists are ok, but the packets dont pass through.I tried creating new VPN profile but the same problem, it seems that only one remote client can be active even base license allows more than 1 client.
Got a single asa 5505 configured in the office. we have 3 site to site vpn connections from this device, which all work from within the office.Ive not setup my pc to connect from home to the asa via the ciso client.
i can connect to all LAN servers on the local subnet, however i cannot connect through the ASA to any of my site to site vpn's.
if i do an ipconfig on my home pc i can see my local ip, mask & gw, and i can see my assigned remote access ip & mask but no gw.
I cannot ping any remote site to site pc's by IP or name.
I am currently having an issue configuring an ASA 5505 to connect via remote access VPN using the Cisco VPN Client 5.0.07.0440 running on Windows 8 Pro x64. The VPN client prompts for the username and password during the connect process, but fails soon after.
The VPN client logs are as follows:
Cisco Systems VPN Client Version 5.0.07.0440
Copyright (C) 1998-2010 Cisco Systems, Inc. All Rights Reserved.
Client Type(s): Windows, WinNT
Running on: 6.2.9200
2 15:09:21.240 12/11/12 Sev=Info/4 CM/0x63100002
[code]....
We have a ASA 5505 in our enviroment. We already configures two site 2 site VPN to our branch offices. Now we are planning to configure remote access VPN. So what should be consider when configuring the remote access VPN in ASA which already having site to site VPN?
View 9 Replies View RelatedFirst off, let me preface this by saying that I'm a novice when it comes to firewalls and more specifically, the ASA. I do however, have an above average understanding of switches/routers.
We have an ASA 5510 running 8.3 and recently I've decided to clean up the last admin's mess. All hosts and servers are on the same subnet, multiple subnets on the same VLAN... and a slew of other problems. Anyway, I recently placed the IT department on another subnet to test some things out before I migrated other departments to different networks. Everything seems to be working as it should be with the exception of one of our servers. The IT subnet is 192.168.150.0/24 and the problem server is on the 192.168.10.xxx network. I'm guessing the issue lies somewhere in the fact this server does have a static NAT and is accessible from the public. Let me give you an overview of what our network looks like:
ISP ---->ASA----->3750----->2960
My workstation is directly plugged into the 3750 switch, and the server is plugged into the 2960. I'm able to ping this server by both IP and hostname. However, I cannot access port 80 by IP or hostname. The users that are on the 192.168.10 and 192.168.11 (sadly both of those are on the same VLAN) network are able to access this server without a problem. Thinking logically, I thought I would send a packet from my workstation, it would head to the layer 3 switch's VLAN interface corresponding to my subnet, realize the .10 network is directly connected and then forward the packet straight to the server. However, it doesn't seem to be working that way. It look like it's being routed to the ASA then being dropped. I guess there's an access rule or firewall rule preventing me from getting to the server. Is there a specific part of my config you will need to see...
I have Cisco ASA 5505 and i want to create vpn remote access ...l
so i created and connected to the vpn ...my problem is to reach my Local connection of 192.168.1.0 /24 i put the WAN Connection in the FA0/0 and put my LOCAL AREA CONNECITON into FA0/1 .. so how i can route or translate my connection , and using cisco ASDM 6.1 in GUI ,,,
We have 3 offices, each with an ASA 5505 as the router/firewall, connected to the cable modem
(NC office) <----IPSEC----->(PA office) <----IPSEC-----> (CT office)
Internally we have a full mesh VPN, so all offices can talk to each other directly.I have people at home, using remote access VPN into the PA office, and I need them to be able to connect to the other two offices from there.I was able to get it to work to the CT office, but I can't get it to work for the NC office. (What I mean is, users can remote access VPN into the PA office, and access resources in the PA and CT offices, but they can't get to the NC office).
Result of the command: "show run"
: Saved:ASA Version 8.2(5) !hostname WayneASA
names!interface Ethernet0/0switchport access vlan 2!interface Ethernet0/1!interface Ethernet0/2!interface Ethernet0/3!interface Ethernet0/4!interface Ethernet0/5!interface Ethernet0/6!interface Ethernet0/7!interface Vlan1nameif insidesecurity-level 100ip address 192.168.1.1 255.255.255.0 !interface Vlan2nameif outsidesecurity-level 0ip address 70.91.18.205 255.255.255.252 !ftp mode passiveclock timezone EST -5clock summer-time EDT recurringdns domain-lookup insidedns domain-lookup outsidedns server-group DefaultDNSname-server 75.75.75.75name-server 75.75.76.76domain-name 3gtms.comsame-security-traffic permit intra-interfaceobject-group protocol TCPUDPprotocol-object udpprotocol-object tcpaccess-list inside_access_in extended permit ip any any access-list IPSec_Access extended permit ip 192.168.1.0 255.255.255.0 192.168.2.0 255.255.255.0 access-list IPSec_Access extended
[code].....
i want my ASA 5505 8.2(5) to access my proxy server on remote lan through VPN my VPN is OK, all PCs of local network can access to remote network.but ASA on local network can't access to remote network.i think it's a NAT problem but ....
local network 192.168.157.0/24 local IP ASA 192.168.157.1
remote netword 10.28.0.0 /16
remote proxy 10.28.1.26
my conf
[code]....
I have 3 networks coming from the DMZ (VPN) and only one works:10.132.24.0/24 Not working10.132.25.0/24 Not working10.132.26.0/24 Working The thing is, the one that works is on the same network as the DMZ(VPN) interface. The other two do authenticate and they get an IP from the VPN Pool. but they just cant access anything.
View 11 Replies View RelatedI have not really set up ASAs nor VPNs on Cisco devices before. I'm currently attempting to configure a remote access VPN between ASA devices, a 5505 and a 5510. The 5510 is meant to be the server and the 5505 is meant to be the easyvpn client. The reason I am opting for remote access as opposed to site to site is that I have many 5505s at remote sites that I will need to configure in the future, and they will be moving around a bit (I would prefer not to have to keep up with the site-to-site configs). The 5510 will not be moving. Both ASA devices are able to ping out to 8.8.8.8 as well as ping each other's public facing IP.
Neither ASA can ping the other ASA's private IP (this part makes sense), and I am unable to SSH from a client on the 5510 side to the 5505's internal (192) interface. I have pasted sterilized configs from both ASAs below.
ASA 5510 (Server)
ASA Version 8.0(4)
!
hostname ASA5510
domain-name <domain>
enable password <password> encrypted
passwd <password> encrypted
[code].....
I try to configure my CISCO ASA 5505 for remote access vpn, and I encounter the following issue : Secure VPN Connection terminated locally by the Client. Reason 412: The remote peer is no longer responding. [code]
View 2 Replies View Related