Cisco VPN :: ASA 5505 / Remote Access VPN - Unable To Access Internal Network
May 7, 2012I have created remote access vpn in my ASA 5505. The tunnel is established but i am not able to access the internal network.
View 3 RepliesI have created remote access vpn in my ASA 5505. The tunnel is established but i am not able to access the internal network.
View 3 RepliesI have a Cisco ASA 5505, with basic 50 license, that is connected directly to the Cable Modem with a public IP. I have VPN configured and active on the Outside interface. When we connect, we connect just fine with no errors, but we are not able to access any resources on the remote network.
ASA IOS version 8.2(5)
Remote Network IP: 10.0.0.0/24
VPN IP Pool: 192.168.102.10 - 25
I am using two firewalls to connect two different offices. Firewall 5510 is running ASDM 6.3 and 5505 is running ASDM 6.2, Problem is that even after connecting two sites, i am unable to ping remote network from either side. I am mentioned static route as tunneled.
View 1 Replies View RelatedA customer has a ASA 5505 with a remote access vpn. They are moving their internal network to a new scheme and would like users who come in on the vpn to access both the exisiting and new networks. Currently the can only access the exisiting. WHen users connect to the remote access vpn, the asa gives them an address of 192.168.199.x. The current internal network is 200.190.1.x and they would like to reach their new network of 10.120.110.x.
Below is the config:
:
ASA Version 8.2(5)
!
hostname ciscoasa
[Code].....
I am trying to build a remote vpn in ASA 5520 Software Version 8.3(1). I am using ASDM 6.3(1) for the configuration. I went through the SSL VPN wizard and did the configuration. I tried connecting to the ASA using anyconnect VPN and I could successfully connect the VPN. My home laptop takes an IP 192.168.60.21 (which I have defined in the wizard). Now my issue is, I can't access any office internal network from this laptop (none of the internal IP is ping ing even). Meanwhile, I could ping and rdp to this laptop(which is connectd by anyconnect VPN) from my office network. One thing I noticed is that when I give a traceroute to an internal IP from the laptop, the first hop goes to my home ISP router.
View 8 Replies View RelatedI am having issue with network connectivity between remote access (RA) VPN users and remote site VPN hosts.
Topology is:
RA VPN laptop (192.168.200.3 /24) ---- internet ---- Head Office (ASA5505) -- LAN subnet 10.0.0.0 /24
SiteB (10.0.10.0 /24) ---- internet ----- Head Office (ASA5505) ---- LAN subnet 10.0.0.0 /24
From head office there is no issue communicating with RA VPN and siteB hosts but Site B hosts and RA VPN users can not communicate each other totally (ping failed too).
Site B is using Cisco 867 router with IPSEC VPN to the ASA5505 at head office. I have added the ACL on this router to access 192.168.200.x /24 for VPN traffic and exempt from NATing. When I enabled ' drop log' in the class-map in the Zone based firewall config, I could not see any ping packt comes in so I believe the issue is at ASA5505 config.
At ASA5505 I use split VPN tunnel ACL and have included the subnet for 10.0.10.0/24 as well as 192.168.200.0 /24. This split tunnel ACL are applied to both the IPSec VPN tunnel and also the RA VPN group policy. The ASA is using sw version 151-4.M5.
What I got is a 5505 ASA firewall and I'm connected to it via VPN. I'm pulling an 192.168.169.x address because that's what we set their company's internet LAN to. Which is what we want. What I can't do while I'm VPN'd in is ping from the internet network to the DMZ, and the same when I try and ping from the DMZ to the internal network.
The DMZ is on a 196.0.0.x network.The internet network is 192.168.169.x network.
I don't need them to have internet access on the DMZ I just want to be able to access it from the internal network. What is going on is we need them to be able to VPN into the DMZ and access their equipment. At this point it would just make me happy to be able to ping from the internal network to the DMZ and I can figure it out from there I've setup rules and applied them and when I wasn't having success I referred back to defaults. Right now the rules are set at default, any thing in and anything out, on both internal and DMZ. I'm using a VPN client and going through Cisco ASDM Launcher to setup the rules and static routes, I haven't done anything with the command line. All the research I've done everyone does it command line, I find it easier to do it GUI. This is my first time working with an ASA firewall.
I have a base config of AnyConnect VPN below, however the ASA 8.3.1 code has deprecated some commands and the VPN/NAT/FW rule syntax is quite different. Can som point out what's missing from the pertinent config below that prevents the VPN Pool from accessing the internal LAN?
The Core LAN router is 1.2.3.1.
!
ASA Version 8.3(1)
!
interface Ethernet0/0
nameif inside
security-level 100
ip address 1.2.3.2 255.255.255.0
I have a 5505 between a vendor router & my company network, vendor is not able to access devices on internal network. I am also not able to access the firewall via asdm
View 10 Replies View Relatedi want my ASA 5505 8.2(5) to access my proxy server on remote lan through VPN my VPN is OK, all PCs of local network can access to remote network.but ASA on local network can't access to remote network.i think it's a NAT problem but ....
local network 192.168.157.0/24 local IP ASA 192.168.157.1
remote netword 10.28.0.0 /16
remote proxy 10.28.1.26
my conf
[code]....
i have a problem with my asa 5505 Remote VPN Connection with local network access , the VPn is working fine and connected , but the problem is i can't reach my inside network connection of 192.168.30.x , here is my configuration
ASA Version 8.2(1)
!
!
interface Vlan1
[Code].....
I´m tring to configure ASA 5505 with VPN Cleint, to access a remote network over a L2L with another ASA 5505, but no sucess. Is there any special feature to this work?
View 2 Replies View RelatedI have one user who is unable to Access Remote Network resources when connected to the VPN on his home network. VPN shows connected and he is given a remote IP from the VPN Pool, but he cannot ping any IP on our network. When connected using Sprint Wi-Fi card he is able to connect and access remote network from the same laptop. Maybe there is some network overlap that I am missing.
see attached firewall config (zzz... being firewall public IP) and remote user route table. ASA 5505 VPN Client 5.0.07.0290
We have an ASA5510 and a few days ago we were unable to access some segments from remote access VPN, the problem was not the config. A few hours later the problem was resolved on its own and I suspect we have an IOS bug. This has happened a few times in the past and its becoming an issue. How can this be confirmed and which IOS should we upgrade to? Prefer not 8.3 given the syntax difference
View 1 Replies View RelatedI am having some trouble accessing some backup Email (Outlook Web Access) and Citrix servers located behind an ASA 5505 firewall at a remote datacentre. Simply put, when I go to the specific URL (e.g. [URL]) I do not arrive at the splash page, I just get a message saying that the server took too long to respond in the web browser. I'm wondering whether I have missed something on the configuration or the firewall itself is not letting my requests through. The remote servers are located at a remote Disaster Recovery site and use the subnet 192.168.4.0/24. I am at head office which is connected to the DR site via a VPN using 192.168.1.0/24.
[Code] .....
I tried the solution posted at [URL] however it did not work on my ASA5505 8.4(2). I thought that it may be because I only have a single public address so the web server is responding to port forwarding through the one public IP already. looking in ASDM it appears to indicate that a configured access list is blocking the server from responding to the internal hosts.
object network Private_IP
host 192.168.1.15
object network Public_IP
host 1.1.1.1
object-group network internal_net
[code]....
Can I fix an access list (or something) to make this work or am I wishing for too much with only one public IP? This worked by default on my Netgear firewall.
We have an ASA 5505 running version 8.4. We are having problems allowing external traffic to access computers behind the firewall. Our current config is:
ASA Version 8.4(3)!hostname ciscoasadomain-name default.domain.invalidnames!interface Ethernet0/0switchport access vlan 2!interface Ethernet0/1!interface Ethernet0/2!interface Ethernet0/3!interface Ethernet0/4!interface Ethernet0/5!interface Ethernet0/6!interface Ethernet0/7!interface Vlan1nameif insidesecurity-level 100ip address 10.2.1.1 255.255.255.0!interface Vlan2nameif outsidesecurity-level 0ip address 152.18.75.132 255.255.255.240!boot system disk0:/asa843-k8.binftp mode passivedns server-group DefaultDNSdomain-name default.domain.invalidobject network a-152.18.75.133host 152.18.75.133object network a-10.2.1.2host 10.2.1.2object-group network ext-serversnetwork-object host 142.21.53.249network-object host 142.21.53.251network-object host 142.21.53.195object-group network ecomm_serversnetwork-object
[code]....
I running site-to-site IPsec VPN in Cisco 2811 IOS 12.4 both site. Here I encounter a problem to access server on Site A from Site B
Site A having Leased Line connected to router with Public IP. I have done static mapping 1 web server to Public IP (NAT). This to allow external users to access the server via Public IP. At the same time, users at Site B would need to access to same server via Internal IP since they have Site-to-Site VPN established. But once I done Static Mapping (NAT), user at Site B unable to access the server at Site A using its internal IP. But external user can access server via Public IP. What went wrong here. Do i need to add extra command to get this done?
I have created Remote access vpn on ASA 5505 (ver 8.2(5) with base license). When I connect from one machine, I can ping the internal network. But when I connect from another machine, cant.I have only decrypts on the ASA side, without encrypts. I was debugging ICMP packets with the capture feature, and saw that echo-reply packets are returning toward the outside interface, but aren't passing through it.
capture test access-list test interface outside
1: 08:54:44.298980 802.1Q vlan#1 P0 x.x.x.x > y.y.y.y: icmp: echo reply
Where x.x.x.x is LAN and y.y.y.y is the VPN client ip. The nat is ok, access lists are ok, but the packets dont pass through.I tried creating new VPN profile but the same problem, it seems that only one remote client can be active even base license allows more than 1 client.
Got a single asa 5505 configured in the office. we have 3 site to site vpn connections from this device, which all work from within the office.Ive not setup my pc to connect from home to the asa via the ciso client.
i can connect to all LAN servers on the local subnet, however i cannot connect through the ASA to any of my site to site vpn's.
if i do an ipconfig on my home pc i can see my local ip, mask & gw, and i can see my assigned remote access ip & mask but no gw.
I cannot ping any remote site to site pc's by IP or name.
I am currently having an issue configuring an ASA 5505 to connect via remote access VPN using the Cisco VPN Client 5.0.07.0440 running on Windows 8 Pro x64. The VPN client prompts for the username and password during the connect process, but fails soon after.
The VPN client logs are as follows:
Cisco Systems VPN Client Version 5.0.07.0440
Copyright (C) 1998-2010 Cisco Systems, Inc. All Rights Reserved.
Client Type(s): Windows, WinNT
Running on: 6.2.9200
2 15:09:21.240 12/11/12 Sev=Info/4 CM/0x63100002
[code]....
We have a ASA 5505 in our enviroment. We already configures two site 2 site VPN to our branch offices. Now we are planning to configure remote access VPN. So what should be consider when configuring the remote access VPN in ASA which already having site to site VPN?
View 9 Replies View RelatedI have Cisco ASA 5505 and i want to create vpn remote access ...l
so i created and connected to the vpn ...my problem is to reach my Local connection of 192.168.1.0 /24 i put the WAN Connection in the FA0/0 and put my LOCAL AREA CONNECITON into FA0/1 .. so how i can route or translate my connection , and using cisco ASDM 6.1 in GUI ,,,
We have 3 offices, each with an ASA 5505 as the router/firewall, connected to the cable modem
(NC office) <----IPSEC----->(PA office) <----IPSEC-----> (CT office)
Internally we have a full mesh VPN, so all offices can talk to each other directly.I have people at home, using remote access VPN into the PA office, and I need them to be able to connect to the other two offices from there.I was able to get it to work to the CT office, but I can't get it to work for the NC office. (What I mean is, users can remote access VPN into the PA office, and access resources in the PA and CT offices, but they can't get to the NC office).
Result of the command: "show run"
: Saved:ASA Version 8.2(5) !hostname WayneASA
names!interface Ethernet0/0switchport access vlan 2!interface Ethernet0/1!interface Ethernet0/2!interface Ethernet0/3!interface Ethernet0/4!interface Ethernet0/5!interface Ethernet0/6!interface Ethernet0/7!interface Vlan1nameif insidesecurity-level 100ip address 192.168.1.1 255.255.255.0 !interface Vlan2nameif outsidesecurity-level 0ip address 70.91.18.205 255.255.255.252 !ftp mode passiveclock timezone EST -5clock summer-time EDT recurringdns domain-lookup insidedns domain-lookup outsidedns server-group DefaultDNSname-server 75.75.75.75name-server 75.75.76.76domain-name 3gtms.comsame-security-traffic permit intra-interfaceobject-group protocol TCPUDPprotocol-object udpprotocol-object tcpaccess-list inside_access_in extended permit ip any any access-list IPSec_Access extended permit ip 192.168.1.0 255.255.255.0 192.168.2.0 255.255.255.0 access-list IPSec_Access extended
[code].....
I have 3 networks coming from the DMZ (VPN) and only one works:10.132.24.0/24 Not working10.132.25.0/24 Not working10.132.26.0/24 Working The thing is, the one that works is on the same network as the DMZ(VPN) interface. The other two do authenticate and they get an IP from the VPN Pool. but they just cant access anything.
View 11 Replies View RelatedI have not really set up ASAs nor VPNs on Cisco devices before. I'm currently attempting to configure a remote access VPN between ASA devices, a 5505 and a 5510. The 5510 is meant to be the server and the 5505 is meant to be the easyvpn client. The reason I am opting for remote access as opposed to site to site is that I have many 5505s at remote sites that I will need to configure in the future, and they will be moving around a bit (I would prefer not to have to keep up with the site-to-site configs). The 5510 will not be moving. Both ASA devices are able to ping out to 8.8.8.8 as well as ping each other's public facing IP.
Neither ASA can ping the other ASA's private IP (this part makes sense), and I am unable to SSH from a client on the 5510 side to the 5505's internal (192) interface. I have pasted sterilized configs from both ASAs below.
ASA 5510 (Server)
ASA Version 8.0(4)
!
hostname ASA5510
domain-name <domain>
enable password <password> encrypted
passwd <password> encrypted
[code].....
I try to configure my CISCO ASA 5505 for remote access vpn, and I encounter the following issue : Secure VPN Connection terminated locally by the Client. Reason 412: The remote peer is no longer responding. [code]
View 2 Replies View RelatedIs there a way I can configure a remote access VPN on a Cisco 5505 using digital certs instead of pre-shared key. I dont want to use a 3rd party CA, can the ASA perform this role? with a self signed cert?
View 6 Replies View RelatedI have an ASA 5505 that is on the perimeter of a hub & spoke vpn network, when I connect to this device using the VPN client I can connect to any device across the VPN infrastructure with the exception of the sub net that the client is connected to, for instance:
VPN client internal network connects to 192.168.113.0 /24 and is issued that ip address 192.168.113.200, the VPN client can be pinged from another device in this network however the client cannot access anything on this sub net, all other sites can be accessed ie. main site 192.168.16.0/24, second site 192.168.110/24 and third site 192.168.112/24. The ACL Manager has a single entry of "Source 192.168.113.0/24 Destination 192.168.0.0/16 and the "Standard ACL 192.168.8.8./16 permit.
I have a remote ASA5505 running 8.4(3) with a working site 2 site VPN tunnel to my main office. (The main office is running an ASA 5510 with OS 8.4.3 as well). The encryption domain is all private IP on main site vs. 172.16.10.0/23 on remote site.
Relevant config of the remote ASA:
interface Vlan1
nameif inside
security-level 100
[Code].....
I can manage the ASA on the outside interface (outside of the site 2 site VPN) using the TACACS credentials I can also ping my management station from the ASA using the inside interface, but as stated, the other way around does not work. I have not yet tested if management from the local 172.16.10.0/23 subnet works, but I will try this next.
Users are connecting to Site A (PIX 515e) via Cisco VPN client and can access servers/resources within that site no problem. They cannot access anything within Site B (ASA 5505) however. Devices communicating between Site A and Site B have no issues (have site to site VPN configured). I'm assuming that I'm missing something in configuration - or is it not possible for VPN clients connected to the PIX firewall and access data on the other network?
View 1 Replies View RelatedHow do I enable remote access to ASDM from outside of the network on the ASA 5505? This would be used for remote access to the firewall at a site that is not utilizing VPN.
View 5 Replies View RelatedI have created a RA VPN with a 5505 using Anyconnect client. My VPN functions perfectly, but now I am trying to limit access so that only one single host on my network can connect. To do this I tried creating an ACL permiting the host and denying all other traffic, but it does not work it seems every one can connect. how I can limit the outside access to a single host?
View 3 Replies View Related