I have a 5505 between a vendor router & my company network, vendor is not able to access devices on internal network. I am also not able to access the firewall via asdm
View 10 RepliesI am having some trouble accessing some backup Email (Outlook Web Access) and Citrix servers located behind an ASA 5505 firewall at a remote datacentre. Simply put, when I go to the specific URL (e.g. [URL]) I do not arrive at the splash page, I just get a message saying that the server took too long to respond in the web browser. I'm wondering whether I have missed something on the configuration or the firewall itself is not letting my requests through. The remote servers are located at a remote Disaster Recovery site and use the subnet 192.168.4.0/24. I am at head office which is connected to the DR site via a VPN using 192.168.1.0/24.
[Code] .....
I have created remote access vpn in my ASA 5505. The tunnel is established but i am not able to access the internal network.
View 3 Replies View RelatedI tried the solution posted at [URL] however it did not work on my ASA5505 8.4(2). I thought that it may be because I only have a single public address so the web server is responding to port forwarding through the one public IP already. looking in ASDM it appears to indicate that a configured access list is blocking the server from responding to the internal hosts.
object network Private_IP
host 192.168.1.15
object network Public_IP
host 1.1.1.1
object-group network internal_net
[code]....
Can I fix an access list (or something) to make this work or am I wishing for too much with only one public IP? This worked by default on my Netgear firewall.
What I got is a 5505 ASA firewall and I'm connected to it via VPN. I'm pulling an 192.168.169.x address because that's what we set their company's internet LAN to. Which is what we want. What I can't do while I'm VPN'd in is ping from the internet network to the DMZ, and the same when I try and ping from the DMZ to the internal network.
The DMZ is on a 196.0.0.x network.The internet network is 192.168.169.x network.
I don't need them to have internet access on the DMZ I just want to be able to access it from the internal network. What is going on is we need them to be able to VPN into the DMZ and access their equipment. At this point it would just make me happy to be able to ping from the internal network to the DMZ and I can figure it out from there I've setup rules and applied them and when I wasn't having success I referred back to defaults. Right now the rules are set at default, any thing in and anything out, on both internal and DMZ. I'm using a VPN client and going through Cisco ASDM Launcher to setup the rules and static routes, I haven't done anything with the command line. All the research I've done everyone does it command line, I find it easier to do it GUI. This is my first time working with an ASA firewall.
I have a Cisco ASA 5505 (version above) and I have someone that needs to SSH into a box behind the ASA. I'm having a few issues trying to configure this access-list and NAT. I've tried many combinations and clearly my IOS is not as good as I thought. What commands should I enter to accomplish mapping SSH from an outside network range to an internal host ?
View 5 Replies View RelatedI now need to configure an ASA 5505 for a small server farm. It's fairly straightforward:isp -> asa5505 -> internal servers,'m using static addresses -- no DHCP involved.VPN works; I can get into the internal network.pinging from the ASA to an external address works,However, I cannot get from a laptop connected to an internal port out to the internet, either using ping or typing an address in the browser.
View 7 Replies View RelatedWe have an ASA 5505 running version 8.4. We are having problems allowing external traffic to access computers behind the firewall. Our current config is:
ASA Version 8.4(3)!hostname ciscoasadomain-name default.domain.invalidnames!interface Ethernet0/0switchport access vlan 2!interface Ethernet0/1!interface Ethernet0/2!interface Ethernet0/3!interface Ethernet0/4!interface Ethernet0/5!interface Ethernet0/6!interface Ethernet0/7!interface Vlan1nameif insidesecurity-level 100ip address 10.2.1.1 255.255.255.0!interface Vlan2nameif outsidesecurity-level 0ip address 152.18.75.132 255.255.255.240!boot system disk0:/asa843-k8.binftp mode passivedns server-group DefaultDNSdomain-name default.domain.invalidobject network a-152.18.75.133host 152.18.75.133object network a-10.2.1.2host 10.2.1.2object-group network ext-serversnetwork-object host 142.21.53.249network-object host 142.21.53.251network-object host 142.21.53.195object-group network ecomm_serversnetwork-object
[code]....
Cisco ASA 5505 Cannot Ping Secondary Internal Network.
View 9 Replies View RelatedFor a customer I have configured a new ASA 5505 firewall with 8.42 software. I had to build 3 ipsec tunnels to different locations and firewalls. All tunnels are working except one. I have to translate the inside network 1 to 1 to a different private range before it is sent over the tunnel. Each host from network 192.168.133.0 /24 has to be translated to a 192.168.112.0 /24 host and then sent over the tunnel. (e.g. 192.168.133.22 translated to 192.168.112.22)
View 3 Replies View RelatedI have configured an ASA 5505 to connect a single internal network to internet, it is not working. I have attached the config
View 9 Replies View RelatedWe have configured a Cisco ASA 5505 with AnyConnect access. This works great. However, these users cannot seem to ping devices on the private network. We have configured all devices on the network with a 10.10.10.0/24 address space. The inside interface of the ASA i 10.10.10.1/24 and the VPN return addresses are 10.10.10.50 - 10.10.10.65/24.They users can utilize SSH and Oracle or MySQL calls but cannot seem to ping. Obviously, I am over looking something.
View 2 Replies View RelatedAfter connecting via anyconnect client 2.5, I cannot access my internal network or internet. My Host is getting ip address of 10.2.2.1/24 & gw:10.2.2.2
Following is the config
ASA Version 8.2(5)
!
names
name 172.16.1.200 EOCVLAN198 description EOC VLAN 198
dns-guard
!
interface Ethernet0/0
description to EOCATT7200-G0/2
switchport access vlan 2
[code]....
I am using ASA 5520 with 8.2.4 IOS. I'm new to ASA/Firewall. I need to do access webserver from outside network.From Laptop (192.168.2.51), If I connect to url... it should open page from 10.10.10.50.I also need to ssh to webserver from laptop. If I ssh to 192.168.2.50 from laptop, it should connect to 10. 10. 10.50. [code]I can't get to webserver from outside network, so now, I connected laptop to directly ASA 5520 outside port with crossover cable.ASA Inside port connects to L3 switch. Webserver also connects to L3 switch. But still doesn't work.
View 9 Replies View RelatedI have the syntax correct and thought process down right on a solution to allowing guest wireless users access to an internal webserver. (DMZ discussion aside)
We have an ASA5510 with interfaces setup as:
outside - 65.x.x.x address
inside - 172.20.1.2
guest_inet - 10.2.1.1
Internally clients resolve our website to 192.168.40.40 and that part works as it should. Clients outside of our network resolve our website to the correct external address (lets just call it 1.1.1.1). We have a NAT statement static (inside, outside) 1.1.1.1 192.168.40.40 netmask 255.255.255.255 and an ACL to permit tcp any host 1.1.1.1 eq www
Clients on our guest_int use an external DNS server and hence resolve our website to 1.1.1.1. However it seems traffic goes out and back in our outside interface and this connection never occurs.
What I'm wondering is the correct NAT statement / ACL to add that would allow our internal clients on the 10.2.1.x network to access our internal website. Would that be: static (inside,guest_inet) 1.1.1.1 192.168.40.40 netmask 255.255.255.255 ? Since there is already an ACL permitting port 80 traffic to 1.1.1.1 we should be taken care of on the ACL side of things, right?
We have a Cisco wireless infrastructure in place that includes a guest network with its own subnet that is a sub interface of the inside interface on our ASA 5520. There are no routes for it to be allowed access to the internal subnets. So it can only access the internet. This is primarily used by the public, but we have several non employee personnel that we only want to give internet access and force them to access the internal network through our clientless SSL vpn portal or through other internet facing internal resources such as webmail.I have done packet traces from within the ASA and the break appears to be there is no ACL allowing the traffic back into the network once the web resource replies to the request and the traffic is attempting to come back into the network from the web resource. Is that as clear as mud?
I know that this has to be a common problem and a way around this is to allow the guest wireless network access to the internal network but only for the select resources that they require. And that this can be done seemlessly by network specific routes and or alternate DNS entries, but I would like to keep this simple and just allow them to access the web resource, webmail and VPN, from the guest wireless using internet DNS servers without route trickery.
A customer has a ASA 5505 with a remote access vpn. They are moving their internal network to a new scheme and would like users who come in on the vpn to access both the exisiting and new networks. Currently the can only access the exisiting. WHen users connect to the remote access vpn, the asa gives them an address of 192.168.199.x. The current internal network is 200.190.1.x and they would like to reach their new network of 10.120.110.x.
Below is the config:
:
ASA Version 8.2(5)
!
hostname ciscoasa
[Code].....
I want to have my port 4 on the asa 5505 only allow access to the internet and not the internal network, what do i need to do?
View 1 Replies View RelatedI am new to Cisco ASA and have been configuring my new firewall but one thing have been bothering. I cannot get internal networks and routing between them to work as I would like to. Goal is to set four networks and control access with ACL:s between those.
1. Outside
2. DMZ
3. ServerNet1
4. Inside
ASA version is 9.1 and i have been reading on two different ways on handling IP routing with this. NAT Exempt and not configuring NAT at all and letting normal IP routing to handle internal networks. No matter how I configure, with or without NAT I cannot get access from inside network to DMZ or from ServerNet1 to DMZ. Strange thing is that I can access services from DMZ to Inside and ServerNet1 if access list allows it. For instance DNS server is on Inside network and DMZ works great using it. [code]
I have a client in a workgroup environment. They are a small company with perhaps twenty systems. Their infrastructure consists of a Dell Switch, a Cisco ASA-5505 which hands out the DHCP and a router. And that's that.They have been using an external IP as their DNS Server to get out to the Web. However, they now want to add an internal Linux-based DNS server.In looking through the ASA-5505 today I noticed a field for DNS enteries. Is this where the IP for this new internal DNS Server (in the secondary DNS field) would go?If so, would it be necessary to reboot the ASA-5505 for this change to take effect?
View 12 Replies View RelatedWe recently changed locations and acquired a new circuit from our provider. They also connected our remote branch office to our main office through MPLS. Now, as I understand it, the branch office basically connects back to the main office through our providers network (MPLS). We have a new router at the branch office which has a gateway of 192.168.1.225. The clients in that office have IP's of 192.168.1.96 - 100, using the gateway of 192.168.1.225.
The main office network is 192.168.0.0 (Gateway of 192.168.0.1)
At this end (Main office), I also have a new Cisco 2900 provided by the ISP, with port 0/0 for the outside connection (connected to the 0 port on my ASA 5505). The ASA's port 1 obviously running into my network hub. The provider tells me that port 0/1 on the 2900 is or should be used to connect the branch office back to here and has an IP of 192.168.0.225, as that's how the provider provisioned it. So, I plug that into the ASA's Ethernet port 0/2. And I'm assuming they have a route setup either on the 2900 or the router in the branch office so that 192.168.1.225 can reach me here at 192.168.0.0.
There is already a static route setup on the ASA: (192.168.1.0 255.255.255.255 192.168.0.225 1). As soon as I plug in the cable, the IP phones at the branch office work, but they can't access the internet or any resources in the main office. My questions are:
1. Shouldn't I be able to just go straight from the 0/1 port on the Cisco 2900 to my hub. At first I was plugging right into the ASA, but I don't think I need to do that, why go from the branch office through my ASA to access resources and then back out the ASA for internet. If they're already coming from 192.168.1.225, through the MPLS network, then they should go right to my network and then back out the ASA.
2. They have to route through the ASA first, in which case, do I need to setup another VLAN for that branch network in conjunction with a static route? I can ping the router and hosts in the branch office through the ASA only!
Below is the running sanitized config:
Result of the command: "show running-config"
: Saved:ASA Version 8.2(2) !hostname ciscoasadomain-name audiology.orgenable password ulzaQiFnKVzDwUmW encryptedpasswd 2KFQnbNIdI.2KYOU encryptednames!interface Vlan1nameif insidesecurity-level 100ip address 192.168.0.1 255.255.255.0 ospf cost 10!interface Vlan2nameif outsidesecurity-level 0ip address 1.2.3.4 255.255.255.240 ospf cost 10!interface Ethernet0/0switchport access vlan 2!interface Ethernet0/1!interface Ethernet0/2!interface Ethernet0/3!interface Ethernet0/4!interface Ethernet0/5!interface Ethernet0/6!interface Ethernet0/7!boot system disk0:/asa822-k8.binftp mode passiveclock timezone EST -5clock summer-time EDT recurringdns server-group DefaultDNSdomain-name audiology.orgsame-security-traffic permit inter-interfacesame-security-traffic permit intra-interfaceaccess-list
[code]....
I have a Cisco 5505, 2 sites that are internal, 1 external IP (dhcp from cable modem). While on my laptop, ipad, iphone, I cannot access the server via it's external IP address. I MUST use the internal IP in order to access this site. I have heard of hairpinning, internal dns server(don't really want this).
View 8 Replies View RelatedI have an old ASA 5505, and I'm having some trouble with Nat Hairpinning. I've done this with other firewalls before and I am having no luck now. I have an internal address that I wish to forward from an external address- so if someone goes to 123.456.789.012:3456 then it will forward to 192.168.1.244:92 (All numbers are arbitrary here- only for illustration). I have and Access Rule and NAT and PAT set up so that I can get in if I originate from outside the LAN. What I am trying to do is to have this work from inside the LAN as well- so that if I am at my desk, and I connect a device and type in 123.456.789.012:3456, it will deliver the content at 192.168.1.244:92. The problem I am having is that it just isn't working, and I cannot figure out why- When I started here, there was an address configured to work this way, and it still works- I just cannot find what is different between what I am doing and what the person who configured it did.
View 5 Replies View RelatedI'm usually not working with this product, but this is what I'm trying to do.I have 2 internal networks setup on our Cisco ASA 5505 firewall. (not done by me, I'm a new to this product)I'm trying to access a server on one network from a PC located on the other internal network. (preferable through the web gui)When I try "Packet Tracer" from interface "Trust4" it fails on the NAT phase.(Source ip: 10.0.4.99, Destination ip: 10.0.6.99)
When I check the NAT rule, it says:
Type Source Interface AddressDynamic any outside outside.
I'm completely illiterate with Cisco appliances but I'm taking care of an ASA 5505 that is configured as a firewall and it has been working for the last years. All of the sudden we are experiencing intermittent connection problems from the workstations. You can be browsing the internet and suddently you'll get a server not found error but you refresh it and it works. This is also intermittent, out no apparent reason it will start working normally again.
I am seeing a bunch of errors like this in the logs:
4 Mar 25 2013 14:34:49 106023 66.235.119.5 69.70.15.61 Deny icmp src outside:66.235.119.5 dst inside:69.70.15.61 (type 8, code 0) by access-group "inbound" [0x0, 0x0]
[Code].....
I have a server that I need to open up some ports on to allow access to the new internal Sharepoint server we're setting up. I've been having some issues getting the ports open like once I put the commands in and save them that server suddenly stops allowing outbound traffic. After looking at a few things I noticed while I was looking at the config file that the ASDM location is showing 2 IP's, both are the same as the server I'm trying to open ports for one being the private IP and the other is the public IP I'm trying to use. Is this the reason I'm having problems when I try to open those ports to my server? Do I need to use both a different private and public IP for this server so I can get my ports to work? The programmers selected these IP's so if I need to change them I'll let them know in case they need to make changes for the Sharepoint setup. This is on an ASA 5505.
View 12 Replies View RelatedI have the connection working with my ASA 5505 but cannot ping the internal network. (Note external interface is getting the IP via DHCP)
View 4 Replies View RelatedCisco ASA 5505
Cisco Adaptive Security Appliance Software Version 7.2(4)
Device Manager Version 5.2(4)
I have and vpn tunnel between a pix network (192.168.200.0/24) and an asa network (192.168.100.0/24); it's been running fine for awhile now but this morning i've come in an i can not access anything on the pix network, (mail, file & web servers). Each attempt to access results in a SYN timeout.
6 Nov 30 2012 14:24:01 302014 192.168.200.9 192.168.100.115 Teardown TCP connection 6014 for outside:192.168.200.9/135 to inside:192.168.100.115/51240 duration 0:00:30 bytes 0 SYN Timeout
I have an ASA 5505 with the security plus software and I'm trying to find out how to assign 2 public IPs to the outside interface and have each IP routed to a separate internal VLAN. For example, IP 1 = X.X.X.1 routed to 192.168.1.0 and IP 2 X.X.X.2 routed to 192.168.2.0. I was told this was possible and I've been trying to find configuration examples, but I can't seem to get anywhere and now I'm getting desperate because I'm scheduled to install it this weekend.
View 1 Replies View RelatedCurrently I have an ASA setup as a Firewall with 1 outside interface and 2 inside interfaces. Initially, the Guest interface was setup to receive DHCP from the ASA and everything was working. I'm adding router and a server for the guest interface and what I'm trying to accomplish now is the following: ASA 5505 > Airport Extreme with a public static IP (69.xx.xx.6), handling DHCP and NAT > Mac Server as DNS Server.Right now, when I connect to my Airport Extreme with any computer, I don't have internet. I don't understand what's wrong. My DNS Server has a reserved IP address: 192.168.226.2 and it's pointing to itself and forwarding the ISP DNS servers, the Airport Extreme is handling the DNS Server IP and the ISP DNS Server IP but I can't connect to the internet from the server. [code]
View 31 Replies View RelatedHow to best troubleshoot some errors I'm seeing on the internal interfaces of my ASA 5505. This is similar to the question at [URL], but the details are different enough that I felt it justified a new discussion.
I have an ASA 5505, running version 8.2(2), 256MB RAM. From time to time (on the order of once a week) our monitoring alerts us that both Internal-Data0/0 and Internal-Data0/1 are experiencing an unusual amount of inbound packets which were discarded with errors, up to 2.3 per second as of this post. Here is what I hope relevant output from my device:
asa# show interface ip brief
Interface IP-Address OK? Method Status Protocol
Internal-Data0/0 unassigned YES unset up up
Internal-Data0/1 unassigned YES unset up up
Vlan1 10.x.x.x YES CONFIG up up
Vlan2 32.32.32.32 YES CONFIG up up
[code]....
1. My understanding is that Internal-Data0/0 is an internal bus that connects to modules like the 4GE. I don't have any modules installed at all, as you can tell. Therefore, what is this bus doing?
2. For that matter, what is Internal-Data0/1 doing? What does it connect to?
3. I'm guessing that due to the input errors and overruns reported for both of these interfaces, it's a buffering issue. Since these are input errors, does this mean that traffic destined to this bus for forwarding is being dropped because the bus itself is running out of buffer memory? How would I see (and subsequently monitor) the buffer memory for these interfaces? Once I am able to see it, what sort of tools can I use to determine what is causing this?
I'm new to this cisco 5505 and I want to carry out a task as simple as a remote access VPN, in my case I did the wizard, with time on my test, I could connect to the VPN, but I can not ping any device internal network. [code]
View 6 Replies View RelatedI have an ASA 5505 with the base license,When I setup the DMZ interface I had to add the deny access to the inside VLAN. The DMZ works fine with WiFi on it, but user's iPhones can't get email unless they turn WiFi off.Is there a simple way to allow HTTPS traffic through the DMZ interface to our internal Exchange server which is NAT'd on the 5505's external IP?
View 3 Replies View Related