Cisco Firewall :: ASA 5505 - Connect Single Internal Network To Internet?
Aug 23, 2012I have configured an ASA 5505 to connect a single internal network to internet, it is not working. I have attached the config
View 9 Replies
ADVERTISEMENT
Cisco Firewall :: ASA 5510 Internal Network Cannot Connect To Internet
May 12, 2012I have an ASA 5510 configured 3 interface Internet_AAPT, Internal_Network and Server_Network. The server network works fine as is able to connect to the internet and services like port 80 work from the internet in. But from the Internal_Network can only get to the server network but not internet (6May 13 201214:17:4030201310.153.111.21253663199.47.216.14880Built outbound TCP connection 42508 for Internet_AAPT:199.47.216.148/80 (199.47.216.148/80) to Server_Network:10.153.111.212/53663 (10.153.111.212/53663). The weird thing in logs i see a connection being made but for some reason its referring to the Server_Network interface? below is my current config...
ASA Version 8.2(5)
!
hostname ASA01
domain-name names
name 10.153.11.184 QNAP
name 10.153.11.192 exc2010
name 10.153.11.133 zeacom
[code]....
Cisco Firewall :: ASA 5505 How To Map SSH From Outside Network Range To Internal
Feb 21, 2013I have a Cisco ASA 5505 (version above) and I have someone that needs to SSH into a box behind the ASA. I'm having a few issues trying to configure this access-list and NAT. I've tried many combinations and clearly my IOS is not as good as I thought. What commands should I enter to accomplish mapping SSH from an outside network range to an internal host ?
View 5 Replies View RelatedCisco Firewall :: ASA 5505 Configuration Cannot Get To Internal Network
Jan 25, 2012I now need to configure an ASA 5505 for a small server farm. It's fairly straightforward:isp -> asa5505 -> internal servers,'m using static addresses -- no DHCP involved.VPN works; I can get into the internal network.pinging from the ASA to an external address works,However, I cannot get from a laptop connected to an internal port out to the internet, either using ping or typing an address in the browser.
View 7 Replies View RelatedCisco Firewall :: ASA 5505 Cannot Ping Secondary Internal Network?
Jan 15, 2012Cisco ASA 5505 Cannot Ping Secondary Internal Network.
View 9 Replies View RelatedCisco Firewall :: ASA 5505 - Nat Internal Network Before Sending Over Tunnel
Oct 27, 2011For a customer I have configured a new ASA 5505 firewall with 8.42 software. I had to build 3 ipsec tunnels to different locations and firewalls. All tunnels are working except one. I have to translate the inside network 1 to 1 to a different private range before it is sent over the tunnel. Each host from network 192.168.133.0 /24 has to be translated to a 192.168.112.0 /24 host and then sent over the tunnel. (e.g. 192.168.133.22 translated to 192.168.112.22)
View 3 Replies View RelatedCisco Firewall :: ASA 5505 / Vendor Is Not Able To Access Devices On Internal Network
Sep 10, 2012I have a 5505 between a vendor router & my company network, vendor is not able to access devices on internal network. I am also not able to access the firewall via asdm
View 10 Replies View RelatedCisco Firewall :: 5505 Configure Internal Router And DNS Server - No Internet
Dec 23, 2011Currently I have an ASA setup as a Firewall with 1 outside interface and 2 inside interfaces. Initially, the Guest interface was setup to receive DHCP from the ASA and everything was working. I'm adding router and a server for the guest interface and what I'm trying to accomplish now is the following: ASA 5505 > Airport Extreme with a public static IP (69.xx.xx.6), handling DHCP and NAT > Mac Server as DNS Server.Right now, when I connect to my Airport Extreme with any computer, I don't have internet. I don't understand what's wrong. My DNS Server has a reserved IP address: 192.168.226.2 and it's pointing to itself and forwarding the ISP DNS servers, the Airport Extreme is handling the DNS Server IP and the ISP DNS Server IP but I can't connect to the internet from the server. [code]
View 31 Replies View RelatedCisco Firewall :: ASA 5505 / Block Internal LAN And Internet Traffic Except LogMeIn Site?
Sep 12, 2011I have configure Cisco 5505 as layer 2 firewall mode. I have vendor machine connected to Cisco ASA 5505 on port 2 as VLAN2 inside then VLAN1 outside connected to my internal network on layer 2 cisco 2960 switch. This machine needs access only to LOGMEIN then block all internal/internet traffic.
vendor machine on vlan 2 inside >> Cisco ASA 5505 vlan1 outside >> layer2 switch >> internal LAN >> Cisco 5520 main FW >>> INTERNET
Cisco Switching/Routing :: 5505 Can't Connect To Public NAT Address From Internal Network
Dec 19, 2011I have an ASA 5505 configured with internal network, a DMZ, and a VPN on seperate subnets. The implicit rules allow my internal client computers to connect to the web servers on the DMZ IP, but I can not connect to the public NAT address from the internal network. I have a DNS server on my internal network and it does resolve to the public IP correctly. NAT seems to be working correctly because if I go outside the network and connect to the public IP or qualified name then I can get to everything correctly. I do not see any messages in the Cisco logs and the packet trace tool shows the route of http from an internal IP adddress to the external (NATed) address is allowed.
Specifically, I can go to http://192.168.1.121 from the internal (192.168.0/24) network, but I can not go to http://72.22.214.121 (the NAT address) from the internal network. If I am outside my cisco then I can go to http://72.22.214.121 easily. [code]
Cisco Firewall :: Connect Internet VPN Clients (on Pix515e) To Internal Resources
Sep 27, 2012i just installed a pix515e ( ios ver 6.2) in my network. and the vpn users can connect to it from the internet successfully but they aren't able to connect to any of the internal resources. some other informaion: i configured nating between the internal network (10.0.0.0/24) and the internet and another static nat policy between an internal resource through another public ip address on outside interface. but right now i need to let the vpn clients to connect to my internal resources.
View 5 Replies View RelatedCisco Firewall :: Anyconnect ASA 2.5 Cannot Access Internal Network Or Internet
Aug 1, 2012After connecting via anyconnect client 2.5, I cannot access my internal network or internet. My Host is getting ip address of 10.2.2.1/24 & gw:10.2.2.2
Following is the config
ASA Version 8.2(5)
!
names
name 172.16.1.200 EOCVLAN198 description EOC VLAN 198
dns-guard
!
interface Ethernet0/0
description to EOCATT7200-G0/2
switchport access vlan 2
[code]....
Cisco Firewall :: 5505 PAT With Single Public IP And Several Servers Behind Firewall
Nov 21, 2012New to the ASA 5505 8.4 software version, but here is what I'm trying to do:
-Single static public IP: 16.2.3.4
-Need to PAT several ports to three separate servers behind firewall
-One server houses email, pptp server, ftp server and web services: 10.1.20.91
-One server houses drac management (port 445): 10.1.20.92
-One server is the IP phone server using a range of ports: 10.1.20.156
Basically, need to PAT the ports associated with each server to the respective servers behind the ASA 5505. Is anything missing from this config? Do I need to include a global policy for PPTP and SMTP? [code]
Cisco Firewall :: 2821 Internet Edge Router From Internal Network
May 8, 2013What is the best way to monitor an Internet Edge router from the Internal network behind the Firewall?We want to pull more information from the edge router like netflow. We can use SNMPv3 and ACLs to keep the router secure.
But I am looking for the best config to keep both the router and firewall as secure as possible while still allowing us to monitor performance and faults.I am running an ASA and a 2821.
Cisco Firewall :: Single Session HTTPS Offload On ASA 5505?
Jan 14, 2013I have an ancient Alteon load balancer which only supports HTTP and telnet access. Our management people only allow HTTPS through the management firewall farm, and don't want to change this policy. So I need a low cost HTTPS to HTTP conversion, ideally on Cisco hardware like an ASA5505. It only needs one concurrent user. Is there a way to configure an ASA 5505 to terminate the inbound HTTPS seession and re-originate a HTTP management session to the Alteon? It looks to me as if the Clientless SSL VPN might do the job.Is there a way to do a SSH to telnet conversion on the ASA, or on a router?
View 1 Replies View RelatedCisco Firewall :: Isolate Internal Net On Port 4 Asa 5505?
Nov 20, 2011I want to have my port 4 on the asa 5505 only allow access to the internet and not the internal network, what do i need to do?
View 1 Replies View RelatedCisco Firewall :: ASA 5505 Routing Between Internal Networks
Feb 18, 2013I am new to Cisco ASA and have been configuring my new firewall but one thing have been bothering. I cannot get internal networks and routing between them to work as I would like to. Goal is to set four networks and control access with ACL:s between those.
1. Outside
2. DMZ
3. ServerNet1
4. Inside
ASA version is 9.1 and i have been reading on two different ways on handling IP routing with this. NAT Exempt and not configuring NAT at all and letting normal IP routing to handle internal networks. No matter how I configure, with or without NAT I cannot get access from inside network to DMZ or from ServerNet1 to DMZ. Strange thing is that I can access services from DMZ to Inside and ServerNet1 if access list allows it. For instance DNS server is on Inside network and DMZ works great using it. [code]
Cisco Firewall :: Can't Access Internal Servers From Behind ASA 5505
Apr 3, 2013I am having some trouble accessing some backup Email (Outlook Web Access) and Citrix servers located behind an ASA 5505 firewall at a remote datacentre. Simply put, when I go to the specific URL (e.g. [URL]) I do not arrive at the splash page, I just get a message saying that the server took too long to respond in the web browser. I'm wondering whether I have missed something on the configuration or the firewall itself is not letting my requests through. The remote servers are located at a remote Disaster Recovery site and use the subnet 192.168.4.0/24. I am at head office which is connected to the DR site via a VPN using 192.168.1.0/24.
[Code] .....
Cisco Firewall :: Internal DNS Server Entry ASA-5505
Jan 12, 2011I have a client in a workgroup environment. They are a small company with perhaps twenty systems. Their infrastructure consists of a Dell Switch, a Cisco ASA-5505 which hands out the DHCP and a router. And that's that.They have been using an external IP as their DNS Server to get out to the Web. However, they now want to add an internal Linux-based DNS server.In looking through the ASA-5505 today I noticed a field for DNS enteries. Is this where the IP for this new internal DNS Server (in the secondary DNS field) would go?If so, would it be necessary to reboot the ASA-5505 for this change to take effect?
View 12 Replies View RelatedCisco Firewall :: ASA 5505 Connecting 2 Internal Networks?
Nov 7, 2012We recently changed locations and acquired a new circuit from our provider. They also connected our remote branch office to our main office through MPLS. Now, as I understand it, the branch office basically connects back to the main office through our providers network (MPLS). We have a new router at the branch office which has a gateway of 192.168.1.225. The clients in that office have IP's of 192.168.1.96 - 100, using the gateway of 192.168.1.225.
The main office network is 192.168.0.0 (Gateway of 192.168.0.1)
At this end (Main office), I also have a new Cisco 2900 provided by the ISP, with port 0/0 for the outside connection (connected to the 0 port on my ASA 5505). The ASA's port 1 obviously running into my network hub. The provider tells me that port 0/1 on the 2900 is or should be used to connect the branch office back to here and has an IP of 192.168.0.225, as that's how the provider provisioned it. So, I plug that into the ASA's Ethernet port 0/2. And I'm assuming they have a route setup either on the 2900 or the router in the branch office so that 192.168.1.225 can reach me here at 192.168.0.0.
There is already a static route setup on the ASA: (192.168.1.0 255.255.255.255 192.168.0.225 1). As soon as I plug in the cable, the IP phones at the branch office work, but they can't access the internet or any resources in the main office. My questions are:
1. Shouldn't I be able to just go straight from the 0/1 port on the Cisco 2900 to my hub. At first I was plugging right into the ASA, but I don't think I need to do that, why go from the branch office through my ASA to access resources and then back out the ASA for internet. If they're already coming from 192.168.1.225, through the MPLS network, then they should go right to my network and then back out the ASA.
2. They have to route through the ASA first, in which case, do I need to setup another VLAN for that branch network in conjunction with a static route? I can ping the router and hosts in the branch office through the ASA only!
Below is the running sanitized config:
Result of the command: "show running-config"
: Saved:ASA Version 8.2(2) !hostname ciscoasadomain-name audiology.orgenable password ulzaQiFnKVzDwUmW encryptedpasswd 2KFQnbNIdI.2KYOU encryptednames!interface Vlan1nameif insidesecurity-level 100ip address 192.168.0.1 255.255.255.0 ospf cost 10!interface Vlan2nameif outsidesecurity-level 0ip address 1.2.3.4 255.255.255.240 ospf cost 10!interface Ethernet0/0switchport access vlan 2!interface Ethernet0/1!interface Ethernet0/2!interface Ethernet0/3!interface Ethernet0/4!interface Ethernet0/5!interface Ethernet0/6!interface Ethernet0/7!boot system disk0:/asa822-k8.binftp mode passiveclock timezone EST -5clock summer-time EDT recurringdns server-group DefaultDNSdomain-name audiology.orgsame-security-traffic permit inter-interfacesame-security-traffic permit intra-interfaceaccess-list
[code]....
Cisco VPN :: ASA 5505 - Can't Connect To Internal Lans Via Vpn
Aug 11, 2011I'm given an ASA 5505 to configure for remote access vpn. I can establish vpn connection to the ASA 5505 but can't access any of the internal vlan/subnets. I configured three of the ASA ports for connection into each of the internal subnets/vlan via a switch.Given below is my full configuration.
ASA5505# sh run: Saved:ASA Version 8.3(1)!enable password bLjadbVl0mgRQWih encryptedpasswd 2KFQnbNIdI.2KYOU encryptednames!interface Vlan1nameif insidesecurity-level 100ip address 192.168.1.1 255.255.255.0!interface Vlan2nameif
[Code].....
Cisco Firewall :: ASA 5505 - Setup Single Port Exclusion For Static NAT?
Sep 20, 2012I have been using static NAT to map between a single server behind an ASA 5505 and a single public IP address. In other words, I've been doing this:
object network NAT_ME
nat (inside,outside) static interface
Now I would like to start using the clientless VPN feature of the ASA, so I of course don't want that particular port forwarded to the server. Is there a way to define such an exclusion? I've tried several things, including setting up a separate NAT rule to direct that port back to the ASA's interface, without luck.
If that is not possible, what configuration would I need to move to in order to get the behavior that I want? It is important that all (non-VPN) traffic is passed exactly as it arrives at the firewall (whether it is coming from internal or external), with the exception of changing the IP address (i.e., I need static port mappings for some of my services).
Cisco VPN :: ASA 5505 - Remote Firewall Does Not Receive Single Packet From Source IP
Jun 3, 2012I have setup an asa 5505 with multiple sub nets (plus license) and a vpn tunnel (ipsec) between this and an other asa on a second branch office (multiple vlans) . Now I need to route only two vlans from the first site to reach some of the second branch networks
let's call them: 1 branch
A-172.16.4.0/24
B-172.16.2.0/24
2 branch
C- 10.10.10.0/24
D- 10.20.10.0/24
E- 10.66.10.0/24
the tunnelis ok From A to CDE . but from B to CDE won't come up. pinging is unsuccessful as well as all other traffic. the connection profile is setup to have both A and B as local networks and A and B by the moment share the same access rules configuration.
logs show firewall 1 let pass and build connections, without denies, but remote firewall does not receive a single packet from the source ip from network B.
Cisco Firewall :: ASA 5505 8.4(2) Allow User To Access Internal Www Server?
Aug 2, 2011I tried the solution posted at [URL] however it did not work on my ASA5505 8.4(2). I thought that it may be because I only have a single public address so the web server is responding to port forwarding through the one public IP already. looking in ASDM it appears to indicate that a configured access list is blocking the server from responding to the internal hosts.
object network Private_IP
host 192.168.1.15
object network Public_IP
host 1.1.1.1
object-group network internal_net
[code]....
Can I fix an access list (or something) to make this work or am I wishing for too much with only one public IP? This worked by default on my Netgear firewall.
Cisco Firewall :: Accessing Internal Sites Via External IP 5505
Jun 4, 2012I have a Cisco 5505, 2 sites that are internal, 1 external IP (dhcp from cable modem). While on my laptop, ipad, iphone, I cannot access the server via it's external IP address. I MUST use the internal IP in order to access this site. I have heard of hairpinning, internal dns server(don't really want this).
View 8 Replies View RelatedCisco Firewall :: ASA 5505 Internal Address To Forward From External One
May 30, 2013I have an old ASA 5505, and I'm having some trouble with Nat Hairpinning. I've done this with other firewalls before and I am having no luck now. I have an internal address that I wish to forward from an external address- so if someone goes to 123.456.789.012:3456 then it will forward to 192.168.1.244:92 (All numbers are arbitrary here- only for illustration). I have and Access Rule and NAT and PAT set up so that I can get in if I originate from outside the LAN. What I am trying to do is to have this work from inside the LAN as well- so that if I am at my desk, and I connect a device and type in 123.456.789.012:3456, it will deliver the content at 192.168.1.244:92. The problem I am having is that it just isn't working, and I cannot figure out why- When I started here, there was an address configured to work this way, and it still works- I just cannot find what is different between what I am doing and what the person who configured it did.
View 5 Replies View RelatedCisco Firewall :: ASA 5505 Allowing Traffic Between Two Internal Networks
Aug 30, 2011I'm usually not working with this product, but this is what I'm trying to do.I have 2 internal networks setup on our Cisco ASA 5505 firewall. (not done by me, I'm a new to this product)I'm trying to access a server on one network from a PC located on the other internal network. (preferable through the web gui)When I try "Packet Tracer" from interface "Trust4" it fails on the NAT phase.(Source ip: 10.0.4.99, Destination ip: 10.0.6.99)
When I check the NAT rule, it says:
Type Source Interface AddressDynamic any outside outside.
Cisco Firewall :: ASA 5505 Intermittent Denies From Internal Workstations
Mar 24, 2013I'm completely illiterate with Cisco appliances but I'm taking care of an ASA 5505 that is configured as a firewall and it has been working for the last years. All of the sudden we are experiencing intermittent connection problems from the workstations. You can be browsing the internet and suddently you'll get a server not found error but you refresh it and it works. This is also intermittent, out no apparent reason it will start working normally again.
I am seeing a bunch of errors like this in the logs:
4 Mar 25 2013 14:34:49 106023 66.235.119.5 69.70.15.61 Deny icmp src outside:66.235.119.5 dst inside:69.70.15.61 (type 8, code 0) by access-group "inbound" [0x0, 0x0]
[Code].....
Cisco Firewall :: 5505 ASDM Location Is Using Same IP As Internal Server
Oct 27, 2011I have a server that I need to open up some ports on to allow access to the new internal Sharepoint server we're setting up. I've been having some issues getting the ports open like once I put the commands in and save them that server suddenly stops allowing outbound traffic. After looking at a few things I noticed while I was looking at the config file that the ASDM location is showing 2 IP's, both are the same as the server I'm trying to open ports for one being the private IP and the other is the public IP I'm trying to use. Is this the reason I'm having problems when I try to open those ports to my server? Do I need to use both a different private and public IP for this server so I can get my ports to work? The programmers selected these IP's so if I need to change them I'll let them know in case they need to make changes for the Sharepoint setup. This is on an ASA 5505.
View 12 Replies View RelatedCisco VPN :: ASA 5505 - VPN Cannot Ping Internal Network
Nov 11, 2012I have the connection working with my ASA 5505 but cannot ping the internal network. (Note external interface is getting the IP via DHCP)
View 4 Replies View RelatedCisco Firewall :: Multiple WAN IPs Routed To Separate Internal VLANs On ASA 5505
May 25, 2011I have an ASA 5505 with the security plus software and I'm trying to find out how to assign 2 public IPs to the outside interface and have each IP routed to a separate internal VLAN. For example, IP 1 = X.X.X.1 routed to 192.168.1.0 and IP 2 X.X.X.2 routed to 192.168.2.0. I was told this was possible and I've been trying to find configuration examples, but I can't seem to get anywhere and now I'm getting desperate because I'm scheduled to install it this weekend.
View 1 Replies View RelatedCisco Firewall :: ASA 5505 / Allow External Traffic To Access Internal Computers
Mar 22, 2012We have an ASA 5505 running version 8.4. We are having problems allowing external traffic to access computers behind the firewall. Our current config is:
ASA Version 8.4(3)!hostname ciscoasadomain-name default.domain.invalidnames!interface Ethernet0/0switchport access vlan 2!interface Ethernet0/1!interface Ethernet0/2!interface Ethernet0/3!interface Ethernet0/4!interface Ethernet0/5!interface Ethernet0/6!interface Ethernet0/7!interface Vlan1nameif insidesecurity-level 100ip address 10.2.1.1 255.255.255.0!interface Vlan2nameif outsidesecurity-level 0ip address 152.18.75.132 255.255.255.240!boot system disk0:/asa843-k8.binftp mode passivedns server-group DefaultDNSdomain-name default.domain.invalidobject network a-152.18.75.133host 152.18.75.133object network a-10.2.1.2host 10.2.1.2object-group network ext-serversnetwork-object host 142.21.53.249network-object host 142.21.53.251network-object host 142.21.53.195object-group network ecomm_serversnetwork-object
[code]....
Cisco Firewall :: ASA 5505 - Discarded Incoming Packets On Internal-Data0/1
Apr 4, 2013How to best troubleshoot some errors I'm seeing on the internal interfaces of my ASA 5505. This is similar to the question at [URL], but the details are different enough that I felt it justified a new discussion.
I have an ASA 5505, running version 8.2(2), 256MB RAM. From time to time (on the order of once a week) our monitoring alerts us that both Internal-Data0/0 and Internal-Data0/1 are experiencing an unusual amount of inbound packets which were discarded with errors, up to 2.3 per second as of this post. Here is what I hope relevant output from my device:
asa# show interface ip brief
Interface IP-Address OK? Method Status Protocol
Internal-Data0/0 unassigned YES unset up up
Internal-Data0/1 unassigned YES unset up up
Vlan1 10.x.x.x YES CONFIG up up
Vlan2 32.32.32.32 YES CONFIG up up
[code]....
1. My understanding is that Internal-Data0/0 is an internal bus that connects to modules like the 4GE. I don't have any modules installed at all, as you can tell. Therefore, what is this bus doing?
2. For that matter, what is Internal-Data0/1 doing? What does it connect to?
3. I'm guessing that due to the input errors and overruns reported for both of these interfaces, it's a buffering issue. Since these are input errors, does this mean that traffic destined to this bus for forwarding is being dropped because the bus itself is running out of buffer memory? How would I see (and subsequently monitor) the buffer memory for these interfaces? Once I am able to see it, what sort of tools can I use to determine what is causing this?