Cisco Wireless :: Switching Between 1130AG Access Points?
Feb 10, 2013
I have multiple cisco 1130ag access point at one of my clients villa. The issue I am facing is when moving throughout the buildingthe laptop and smartphones will not switch between AP’s unless it loses its connection with its existing AP then it will see the other AP that is closer and connect to it.
For example, I start at one end of the building where it connects to AP#1 , if I then slowly go to another section of the villa, it it will not switch over to AP#2 until the signal is lost from AP1
I have following settings
AP's are Cisco 1130AG
Single SSID with WEP Security
View 9 Replies
ADVERTISEMENT
Feb 11, 2013
what I can do to accomplish my end goal of safe public wifi and configuration.I have 2 domain controllers (for redundancy) with a split scope for DHCP and they both serve DNS. I have VLAN 2 (management), VLAN 3 (Servers), VLAN 4 (Wired Access), VLAN 6 (Wireless Access) and VLAN 480 (Outside Wireless). I have setup INT VLANs for all of these on my main router (Cisco 3550) with the ip-helper address to the DC for all but the VLAN 480. All of this works great, and the scopes are setup just like the VLANs. (ie 192.168.2.0 (management) .3 (servers) etc.)I was wondering if there is a way to have VLAN 480 get DHCP from the cisco 3550 as a random address say, 172.16.0.0 255.255.248.0?
On a side note, I have seperate Wireless Access Points for the outside. (From a guy before me) I understand you can have a guest wireless setup on the newer Access Points, and trunk (cisco term) the 2 VLANs and seperate them out with Access Control Lists so they don't talk to each other, but I would rather just give the VLAN 480 it's own DHCP from the router.
View 14 Replies
View Related
Oct 13, 2010
I am trying to find a way to login to our wirless access point. I have a Aironet 1130AG series wireless router. I have the ip address. It is a POE device so i dont have a power supply for this device. When it is on I can see the Wireless Network but the passcode has been lost and no one knows it. Is there a default IP address for this equipment? There is an Ethernet port for a console but without the power supply i cannot access it.
View 3 Replies
View Related
Jul 27, 2012
One of my Wi-Fi site, having cisco_1130AG access points nearly 110nos as of now i installed 80nos, after installing, in out off 80nos nearly 12nos of APs's radio is showing down.
Again i reset and re-configure then it is working fine, is there any readio (802.11g/a) problem in this model?
View 5 Replies
View Related
Mar 23, 2011
We have a guest wireless network using 1130AG Access Points. Is it possible to allow devices on this network access to an Internal IP? I know that kind of defeats the purpose on the guest network, but we'd like to give access to internal email to these devices. Currently this does not work because you cannot loop back into the network to gain access (out the firewall and right back in the same port).
View 5 Replies
View Related
Oct 22, 2012
We currently have around 150 2975 switches and have had problems with it them not handing out PoE power to the cisco phones and access points at random times. There is plenty of power left for the switch to use. We have at least 15 that will be running fine for about a week and then all of the devices that use PoE power will shut off and will not come back on until we reload the switch. If you console in there aren't any messages that pop up and if you look at the port it just shows on connected or will show IeeePD in the power inline. We have contacted Cisco TAC and they just RMA them.
View 6 Replies
View Related
Nov 4, 2012
In our Environment we used to Connect to wifi using Radius Authentication Through AD Account (Encryption: TKIP and CIpher, Authentication Open+EAP and Network EAP, Key management WPA) this settings which will be done And pushed through AD Itself.We Use CIsco 1130AG, 1200 Series in most of the areas which have no Issues.But We Have Some trouble with Cisco WAP4410N Access point.In This Access point users were not able to Connect to wifi through Radius Authentication.However users were able to Connect to these Access point, but it is unsecured, whoever configure's the correct client settings in their PC. They can connect to SSID. This Access point is capable of supporting Radius Authentication?
View 4 Replies
View Related
May 31, 2011
We have a Cisco ASA5505 here that provides DHCP and routing to all our devices in our network. We also have a few other switches and wireless access points connected directly to the back of the ASA5505.For the past year all the wireless network signals has been working fine however starting last month, none of the wireless access points (we have three WRT54G) would allow proper connection (dropping connection, slow internet).I thought this maybe all THREE wireless access points are toast/bricked. So i went out and bought brand new Netgear WN604 and even with the new WAP i'm having same connectivity issues (really slow internet).When hardwired directly to the switches we get BLAZING fast internet & connectivity, no issues.
I called CISCO TAC and they automatically said "our ASA5505 is fine, it has to be your wireless access points" not working properly. I explained to them that i also purchased two brand new access points and they are doing the samething now, how can that be?
View 11 Replies
View Related
Apr 9, 2013
I've had some long standing issues that I've tried various things to fix. I have two WAP4410N access points set up at a smaller sister company. Wireless clients (laptops) are not receiving DHCP assigned IP addresses. If I type in an IP manually, it works fine.The sister company has a point to point T-1 connection to our main building. Our main building has the DHCP server. The router on the sister company end is configured as the DHCP relay.
I've upgraded the firmware three different times in the past to hopefully resolve the issue, but no luck. Just today, on one of the WAP4410N's, I upgraded to the 2.0.6.1 firmware (backing up config, reset to factory default, upgraded firmware, reset factory default again, restored config). After the first reset to factory defaults, the Access Point itself picked up a DHCP address from the server, and I verified this in the DHCP console on the server, so I know that the DHCP relay is working. However, my laptop would not get a DHCP address when connecting wirelessly through that access point. It is a Windows 7 Enterprise laptop. I also could not get a DHCP IP with my iPhone connecting to wireless, to rule out specific issues with just a laptop.I have the DHCP lease times for the subnet that these WAP4410Ns are on set to 2 hours.
To put a cherry on top, there is one laptop that stays in a lab area at all times, connecting wirelessly, and it DOES get a DHCP IP address (I can see in the DHCP console that the lease for this laptop continually renews as needed). I do remember on initial config when I couldn't get it to work, that I did a manual set up, gained connection, then switched it to DHCP...but that doesn't work for any other laptop.Why would the access points get DHCP address, but not anything connecting to the Access Points?
View 5 Replies
View Related
Mar 15, 2012
Using WISM with 7.0.220 and 1240 and 3502 APs. Just found that some of our 3502 AP didn't enbale their clean air and CDP when installed. This only happened on a few new APs. But the area these APs where we seem to have had a few problems with PCs. The only PCs effected where Computer On Wheels (COWs), Dell 780 Desktop with a Cisco Wireless Card.
Using an interl wireless card and others in thes areas worked.Once I enabled the CDP and Clean Air, the COWs worked.My question is with the APs not having CDP enabled, could this affect the cisco wirelss card in the COWs?
View 6 Replies
View Related
Aug 30, 2012
At my school we have a lot of access points, but sometimes the computer use the wrong access point. How can I solve that? Is there a program for switching access point?
View 8 Replies
View Related
Nov 10, 2011
BTW the halls are next to each other.The house and the 3 halls are in the vicinity however not attached together(i.e. wall to wall). The distance between the house and the first hall is approx 1 road width distance.ISP is Virgin and the internet was installed this year hence has the latest Virgin Home Hub.I am aware that i probably require 3 wireless access points (1 for each hall).The first wireless access point will need to be connected with a RJ-45 cable running from Home Hub. Can i connect the Wireless access points up together or do they all need to come from the ADSL hub?I am not sure what Wireless access points would be best and how to go about connecting this all up
View 2 Replies
View Related
Jul 5, 2012
I have New Pace 4111n Wireless Router that I got from AT&T and is setup on 1st floor, but its wireless range does not get me to 2nd floor. I also have the 2Wire wireless router from AT&T. In Addition, I have ethernet connection from level 1 to level 2 as well.
I was wondering if it is possible to have the Pace Wireless N router to work as modem and wireless access point, at the time use the 2Wire router to broadcast wireless and act as access point for 2nd floor.
IF its doable, how should the two be configured and connected.
View 5 Replies
View Related
Jun 17, 2012
I am trying to deploy several AIR-CAP3502E-E-K9 access points from a cisco 5508 wire lan contoller running ver 7 code. However iam having difficulty registering the access points with the WLC. The wlc is connect to a 3650 switch, and each access point is connected to a 2960 switch. A bad update was not allowing the access points to get their correct firmware.
View 7 Replies
View Related
Aug 9, 2012
I am having an issue here. I have 2x 5508 that each have 100 AP license and a little under 200 access points. Basically all of the access points are using DNS to connect to the primary controller that has the DNS entry. Basically half of my access points need to be on the second controller and in order to do this I have been using the high availability mode of each access point to push them to the second controller IP address.It was working perfectly until now. I have pushed 28 access points to the second controller and the last two I need to push at this location just keep resetting on the primary controller. Neither controller is configured as master controller.
View 4 Replies
View Related
Nov 18, 2012
I need an Wireless Access Point.Two SSID simultaneously in different IP Rangeit is with a simple browser GUI to manage? (not console and controller)a distance of about 50 (we can place multiple APs)N speedDual BandWhich series meets the above requirements?It can also Wireless-N Gigabit Router as 4400N, but it does not support Dual Band.
View 1 Replies
View Related
Jan 17, 2013
I have access points deployed across several buildings that each have a different IP scheme and their own T1 line. Is it possible to configure the 5508 controller to allow these access points to use the IP scheme assigned for that particular building or will dhcp always assign an IP address to the connecting client based on the IP scheme of the building that the controller resides in?
View 1 Replies
View Related
Jul 13, 2011
I need an official document from Cisco saying the APs models supported by the WLC 5508. Specially, I need to know if the AIR-AP1242AG-T-K9, converted from standalone, will be supported by the 5508.
View 1 Replies
View Related
May 1, 2013
We have a couple of Access Points which are not registering with WLC 2500. I followed-up on the two LAPs in the dorm. They were cycling through red, amber, green, indicating they were trying to join the controller but could not.
Recently, we have changed our IP Schema for the Wireless Devices and I believe there is an IP Conflict between APs and WLC. Earlier APs were cofigured with Static IP Address assignment, thus they can't change their IP Address.
how to reset the Access Point? I know we can hard reset them by pressing the Mode button manually.
Is there another way via which this can be done witout removing the Access Points from their enclosures?
View 7 Replies
View Related
Jun 20, 2012
install AP1042N access points?
Situation: I have a store where there is already installed an AP1042N. In the back of the building there is no wireless signal. I want to install a second access point to extend my range;
View 3 Replies
View Related
Apr 6, 2012
At home, I use my laptop to connect to my wireless router without any trouble.But at: public libraries, Starbucks, hotel rooms... any free public wifi? All attempts to connect meets with the same error: "unable to connect to network" (preceded by the system hanging for a lengthy amount of time). Windows advises me to unplug the router and plug it back in, which obviously isn't an option.It's annoying to troubleshoot, because I'm only having the problem at times where I have no wired access (hence: no way to get to forums like these and look for an answer, update drivers, whatever).
View 6 Replies
View Related
May 7, 2012
I have a customer who wants wireless for his entire school campus. In the gymnasium, he says that there will be at lease 500 people with wireless devices at one time during a game or event. How many access points will I need to provision to accomplish this request? We are quoting the AIR-CAP3602I.
View 2 Replies
View Related
Jun 22, 2011
I am trying to setup EAP-TLS authentication for my wireless access points, but I can't sign my ACS certificate with my enterprise CA certificate.If I generate a self-signed certificate on the ACS server, and try to sign it on my CA, I get an ASN tag error. It looks like that is because the ACS server is not in the certificate path of the CA server.If I generate a certificate on the CA and try to import it into ACS, I get a "unable to parse certificate" error. Is there a way to edit the Certificate Trust List in 5.2? It looks like that was possible with 4.2, but not with the latest version.
View 1 Replies
View Related
Oct 7, 2011
I am recently engaged by a client to convert his network to wireless network. My client operates in an office with 8 floors and also concrete walls. On making my research i came about your product Cisco AP500 Series Wireless Access Points.I will like to know if this product can work for my client perfectly or I will need to get other enhancement to make it work at its optimum.
View 2 Replies
View Related
Mar 11, 2012
I have 8 no. AIR-LAP1131AG-A-K9 and WLC 2112 Wireless LAN Controller,i configured the device and its working at deffent SSIDs but when i am trying to enable same SSID on all LAP it shows "AP on dupplicate SSID found and Layer 2 security found".
View 1 Replies
View Related
Mar 6, 2013
I would like to start setting up a Cisco Wireless Lan Controller 5508 with some Cisco 1262n AP's. How to start setting this to take advantage of having this wireless lan controller? I have a DHCP server, a Cisco 6509, and Cisco 3750g that connects the access points. I have Vlan 50 for wireless access points.
View 7 Replies
View Related
Jul 9, 2012
We have a Cisco 2500 WLC with 136 APs. Recently, we discovered eight APs that were not listed on the Wireless > Access Points > All AP list. These APs were once working and connected, but now they are no longer in the All AP list. I located one of these APs and found the green LED blinking. I power cycled the AP and it came back online with a solid green LED and was then registered on the All AP list. The All AP list will only show the connected APs. I would like to know if there is a method to show the APs that were once connected and are no longer registered so we can better identify when an AP is not working?
View 15 Replies
View Related
Sep 2, 2010
Access points 1142 controller 5508 running code 6.0.196.0 When you set the access point port speed with "config ap duplex full speed 1000 all" the access points leave the controlle and do not rejoin. I have had to reset the the access points manually with a power down and hold the reset button.
View 13 Replies
View Related
Apr 3, 2013
I am trying to build a bridge between two of my access points. Both the access points connected to the wireless controller. I have changed the AP mode to "Bridge" after changing the power to custom.
The access points have both rebooted - but never "joined" the controller again. I have checked on the following pdf.
[URL]
One thing I can see - if I run a ping to the last IP.. every now and again I get a single response then it drops again. Via the console on the access point I can see it's getting to the controller, getting its name then reading something that caught my eye
"
*Apr 4 11:41:24.451: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Apr 4 11:41:19.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 57.24.10.53 peer_port: 5246
[Code]......
View 9 Replies
View Related
Mar 14, 2013
I'm looking to extend wireless coverage outside the building and was think of using 2600e APs with AIR-ANT2566P4W-R patch antenna mounted externally.Is this a valid combination?
I've had a look through various bits of documentation and this antenna seems to be supported but can't see documentation that details of what low loss cables and lightening arrestors are compatible.
View 6 Replies
View Related
Mar 17, 2013
I have an existing setup of older 1242AG-E-K9 access points with Air-ANT-ANT5160 antennas connected to them. Goal is to replace old AP's with new AIR-LAP1262N-E-K9 model. Question is that can I use only one antenna per radio? Does it work? I know that N-standard requirement is 3 antennas per radio (3 x 2.4G and 3 x 5G) but we need only B/G to work. Plan is to re-use existing AIR-ANT-ANT5160's and order new AIR-ANT2506 antennas. Setup per AP would be 1 x 2.4G and 1 x 5G.
View 7 Replies
View Related
Dec 7, 2011
My boss just asked me if there was a way for him to move from point A to Point B with his wireless laptop and NOT have to reauthenticate at point B if I install another access point there. Right now I have us setup on a Cisco WAP4410N Access Point that works well when he's within range of the antenna. The point B location is upstairs and while it's only about 50-70 feet away from the Point A access point the signal he's getting there is very weak so he wants me to install another AP there.
IOW he wants to authenticate once at point A and when he walks up to point B he wants the laptop to pickup the newer hotter signal when I put another AP point in.
View 3 Replies
View Related
Jul 25, 2012
mounting 3500i access points (AP) to the ceiling ...The ceiling is an Armstrong suspended ceiling with 24" mineral fiber drop ceiling..What are recommendations and best practice - mount AP under or above the ceiling? Initially, I considered the mounting options from Oberon Inc. (p/n :1064-00), but given the difficulty by purchasing this product in my country have to consider other options..I must say that the decision to mount the access point to the ceiling like this:
Now I looking a version of the mount АP with flush-mount kit for tiled ceilings (AIR-AP-BRACKET-3=)..
View 1 Replies
View Related
