Cisco Wireless :: 1130AG Series - AP In Autonomous Supported Model?
Feb 16, 2013what are the series of access point that are supported without WLC. anteena should be in built and capability link 1130ag series.
View 9 Replieswhat are the series of access point that are supported without WLC. anteena should be in built and capability link 1130ag series.
View 9 RepliesWhat 113X AP model will work in Autonomous and LightWeight Mode? I want to buy some 113X AP's for my lab and want to make sure I don't get stuck with the ones that only run in one mode. I am looking at buying this one AIR-AP1131AG-N-K9 802.11a/b/g. Will this model work in both modes?
View 1 Replies View RelatedWe have few sites with old 1232 ag AUTONOMOUS existing AP's , They are connected through 1 mbps link to main office .Now we are planing to upgrade with WLC 5508 and few 1140 ap . but we want to use these same 1232ag ap on some sites.So we need to upgrade it to LWAP .
1>Is it possible to upgrade this model of AP
2>Which is the ios i should download , is it avaliable in cisco site (as this ap is end of sale now )
3>How the step to upgrade this autonomous ap
I purchased the AP wrongly, instead of getting the "Standalone/Autonomous" (AIR-SAP2602E) version but I purchased the controller-based version (AIR-CAP2602E); my question is can I use "ap3g2-k9w7-tar.152-2.JB.tar" too flash it to a "Standalone/Autonomous" version?
View 21 Replies View RelatedDo we have Option to add MAC address of specific laptop or Mobile to connect to the Access Point in cisco Aironet AP 1260 series in Autonmous mode
View 4 Replies View RelatedI am planning to buy new AP for my existing setup. we are using 1131AG series AP, we need to go for new one with n supported with external antenna.
Current software version on controller is : 7.0.235.3
I am running the upgrade tool on Aironet AP1230B-A-K9. I can't join the controller by using the upgrade tool. the error is "AP does not have Supported Radio". What radio is the upgrade tool or controller look for on Aironet 1200 series? This AP is running 802.11b. However, I have several APs which the same model is running on the same one controller. The controller is model 4402.
View 8 Replies View Related in need of 800 series router's model comparison.
Any one have suitable documents for that? I need on some urgent basis.
I searched on Cisco and found below URL. But i want complete comparison in excel or ppt for that. [URL]
Is the Cisco 850 series router supported with PoE-PowerInjector 800-PwrInj? In the 850/870 cabling guide I found a reference only 870 series would be supported.
View 2 Replies View RelatedI have a CiscoWorks LMS 2.6 and i would like to know if the new Switches Catalyst 2960-S Series are supported with this LMS version?
View 1 Replies View RelatedI wonder are 4500-E series line cards (i.e. WS-X4648-GB-RJ45, WS-X4748-UPOE+E and WS-X4606-X2-E) supported on 4507R chassis? Datasheet says "Classic line cards may be deployed in both classic and E-Series chassis with either classic Cisco Catalyst 4500 Series supervisor engines or with the Cisco Catalyst 4500E Series Supervisor Engine." But it says nothing about E-Series line-cards being (or not) supported on classic chassis (like 4507R).
View 3 Replies View RelatedCan I associate the non-root bridge model 1310 to the root bridge model 1400? Is there any problems on the configuration I need to be aware of?
View 7 Replies View RelatedI have a couple 1130AG switches. I'm trying to pull an image file from the flash on a Cisco Air AP1131AG. The file is c1130-k9w8-mx.124-23c.JA4.tar. The issue that I'm seeing is, I do not see a copy command to go through the tftp process. I've tried to use tftpd32 and enter the IP of the AP as the remote host, but that is not working either. Do I need to connect an ethernet cable straight to the AP in order to use Tftpd32, or can I use a console cable?
View 9 Replies View RelatedI am trying to join my 1130AG-E-K9 AP to my 2016 WLC, but it is stuck in a boot loop and will not connect to the controller. [code] I found some details here: url... but I'm not sure what it means that I have a 'SSC AP'. I am not local to this AP, though I do have a console connection to it-what do I need to do to get it working again? It just continually goes through this error and reboots every 30 seconds or so, so it's useless at the moment.
View 3 Replies View RelatedWhere is the link to download recovery IOS for AP1130AG.
View 4 Replies View RelatedConfiguring a Cisco 1130 AP (autonomous) to a 1861 router.
I am struggling to work out how to connect this and get it working.
Router has 2 v lans, VOICE and DATA. All switch ports configured for access v lan (DATA) and voice v lan (VOICE)
We need the AP to have an SSID for VOICE and DATA and the gateway/DHCP server for each of these to be the router.
I got a problem with a ap that I have here where I do not have the password and I did the process to reset the AP to factory defaults, but the configuration still the same, and the AP still asking for the enable password, its the same problem poused before in this link URL. I did the same process but I still have the old configuration on the AP. I noticed that the AP change the image when I reset the AP, using the mode button. the AP is starting with and rcv image. I need to reset the AP to its initial configuration.
View 9 Replies View RelatedI'm trying to set up this 1130AG with a private wireless network and a guest wireless network. Initially it had just one wireless (private) and it worked fine, but then when I created the two VLANs for each SSID and then the guest SSID and now the guest SSID is visible/broadcasting, but the private SSID has disappeared or is off.
P.S. - It's a Cisco Aironet 1130AG (AIR-AP1131AG-A-K9) running 12.3(8)JEA system software and I'm using the web GUI (I'm not familar with the command line for Cisco products yet).
I have multiple cisco 1130ag access point at one of my clients villa. The issue I am facing is when moving throughout the buildingthe laptop and smartphones will not switch between AP’s unless it loses its connection with its existing AP then it will see the other AP that is closer and connect to it.
For example, I start at one end of the building where it connects to AP#1 , if I then slowly go to another section of the villa, it it will not switch over to AP#2 until the signal is lost from AP1
I have following settings
AP's are Cisco 1130AG
Single SSID with WEP Security
i have installed ISE1.1 on VM and other hand vWLC7.4 also there in VM i am using 1130AG APs in flexconnect mode and using central auth and central switch.i wan to configure it for CWA(central web Auth) from ISE but a little a bit confuse about ACLs.
View 2 Replies View RelatedI am trying to find a way to login to our wirless access point. I have a Aironet 1130AG series wireless router. I have the ip address. It is a POE device so i dont have a power supply for this device. When it is on I can see the Wireless Network but the passcode has been lost and no one knows it. Is there a default IP address for this equipment? There is an Ethernet port for a console but without the power supply i cannot access it.
View 3 Replies View RelatedOne of my Wi-Fi site, having cisco_1130AG access points nearly 110nos as of now i installed 80nos, after installing, in out off 80nos nearly 12nos of APs's radio is showing down.
Again i reset and re-configure then it is working fine, is there any readio (802.11g/a) problem in this model?
I have 1 EuroDocsis modem and 2x 1130AG wireless things.How do I manage to get this connected to each other wirelessly?The internet is allready configured at the EuroDocsis modem and I now want to distribute it wirelessly to both 1130AG's. The EuroDocsis is using WPA2 PSK.I read something about WDS, but I don't get that to work either.
View 1 Replies View RelatedI have a Problem with a customer WLAN. The customer has a Aeronet 1130AG AP. Now i should configure a Aironet 1130 Repater for this WLAN. The initial connection from the Repater with the AP is no Problem. But after some time the Repeater lost the connection. On the AP i see following Messages:20Jul 19 19:05:28.061InformationInterface Dot11Radio0, Deauthenticating Station xxx Reason: Previous authentication no longer valid 21Jul 19 19:05:28.061WarningPacket to client xxx reached max retries, removing the client 22Jul 19 16:43:59.412InformationInterface Dot11Radio0, Station yyy Associated to Parent xxx23Jul 19 16:43:57.901InformationInterface Dot11Radio0, Deauthenticating Station yyy 24Jul 19 16:43:56.536InformationInterface Dot11Radio0, Station yyy Associated to Parent xxx 25Jul 19 16:43:51.555InformationInterface Dot11Radio0, Station zzz Associated KEY_MGMT[WPA PSK] 26Jul 19 16:43:29.078InformationInterface Dot11Radio0, Station Repeater01 xxx Associated KEY_MGMT[WPA PSK]
View 2 Replies View RelatedWe have a guest wireless network using 1130AG Access Points. Is it possible to allow devices on this network access to an Internal IP? I know that kind of defeats the purpose on the guest network, but we'd like to give access to internal email to these devices. Currently this does not work because you cannot loop back into the network to gain access (out the firewall and right back in the same port).
View 5 Replies View RelatedCan Controller 4400 series work with Aironet 3600 series?
View 5 Replies View RelatedWhat's the main technical differences among the 1140 AP series and the 1260 AP series?I know that the 1260 supports external antennas while the 1140 supports internal antennas, but apart from that, is there any other important difference ?
View 10 Replies View RelatedThe 1130ag was the LAP model but I upgraded it to run in autonomous mode. My understanding is that it cannot assign IP addresses but I just want that confirmed. It is not connected to a WLC nor a server that can do DHCP.
View 5 Replies View RelatedHow can I enter into "interface configuration" on Aironet 1130AG, AIR-LAP1042N?When I put following commands in enable conf tinterface Dot11Radio1 but, it fails and I cannot enter into "interface configuration".How can I do this ?The reason why I enter into conf tinterface Dot11Radio1 because I want to disable cdp via CLI ( serial console).
View 9 Replies View Relatedwe just deployed a cisco wireless solution with WLC4404-100, WCS, and a bunch of 1130AP and I experience some problem with file copy under windows xp. The file copy is working fine with my Ethernet connection however.The symptom is as follow. I cannot copy large file from a share to the computer. The copy starts then after a while (let's say 30MB copy over a 100MB file) it stops with the error 'File copy error: The network name is no longer available'. When this occurs, I still have my wireless card connected and I can ping my computer from the controller.I tried to adjust some radio settings (channel, power on the AP I'm connected to) because we have a large wireless network here, but no success. I also update the wireless card driver, create a new SSID, etc. No success at all. However the copy went fine for small file size.
View 9 Replies View RelatedSeveral 1130AG AP, auto IOS, are showing the same three errors;
1. 'Error' Interface BVI1 Changed to up
2. 'Error' Interface Fast Ethernet0 Changed to up
3. 'Error' Interface Dot11Radio0 Changed to up
ATTACHED image
Why these interfaces coming 'up' would be an 'error'? Seems almost like hardware failure/s. So we have been investigating on several 1130AGs bought from different places, with different configs and still get the errors. The APs appear to 'work' (i.e. basic config, wireless working, clients assoss., data flows to internet and back through APs) but the error causes the event log to show 'error' and for the status LED to turn 'yellow', instead of 'light green' (light green when working normally and no clients assos).
I have worked with many cisco APs and never ran across these two errors.
At first I thought it was a power issue, as the AP will boot up in low power if it doesnt think it's getting enough power, which could cause the IOS error possibly. But all of our APs are powered by wall plug cisco 48v OEM plugs, no POE injectors or switches. We even changed the settings in power of the IOS to 'pre-compatiable' POE and similar and still recieve the error and yellow LED status light. We looked into this power issue because we wanted to rule out if these was what was producing the errors that were reporting.
The second thing we did was setup the test APs with a very basic config, one ssid, no security, as to rule out a config error and also, no config will make the radios disabled, so without a basic config the APs cant be tested anyway (since the radios are now disabled from default). so we tested very basic configs and still getting the error and yellow LED (which all manuals say it should be light green normally working and no clients). all config changes brought wireless up and we can connect clients and data flows but still the errors stay and yellow LED once all clients disconnect. Note; when clients connect the yellow LED turns to light green, but thats not the colors the manual states they should be which is odd).
Third, a couple engineers suggested this error was from the AP scanning channels to choose the least congested (default config) and it will pick a channel but produce this error still and go yellow. We changed the configs to the least congested channels and it reboots and still gets these errors.
We have tried several IOS software packages, some newer, some older, all auto. though, no LAP.
We googled the errors but could only find ONE post with these errors. Some engineers said these errors are 'normal' and they have seen them before, but theres nothing on the web about the errors and we have owned 20-40 different cisco IOS APs and never seen this, and we have the same issues with 4 1130AGs, all in almost new condition, bought from different places.
Unless you have opened a 1130 many people dont know the status LED is actually 3 LEDs (one assembly with 3 micro LEDs, blue, green and red) that combine in color (the micro LEDs light up in different intensities causing many final color combintations), and the LEDs colors mix together via a plastic light guide on the top to show the status LED, and we believe the error is causing the status LED color to be off because the error is making the yellow light up and mix with the other colors causing all the other colors to be incorrect. we have researched trying to clear the error by 'clear logging' CLI command, hoping that may clear out the interface error and turn the yellow LED off because there would be no log of the error, but we have not succeded.
I can not get this to work.I have 1 EuroDocsis modem and 2x 1130AG wireless things.How do I manage to get this connected to each other wirelessly?The internet is allready configured at the EuroDocsis modem and I now want to distribute it wirelessly to both 1130AG's. The EuroDocsis is using WPA2 PSK.
View 3 Replies View RelatedI have installed an Aironet 1130AG and utilized a power injector for the power source. I have the settings configured correctly in IOS, but the AP takes about 7 minutes to come on (illuminate LED status lights) once the Ethernet cable is connected. Is this 7 minute power-on delay normal when using POE? I am used to the instanteous "on" that usually comes with Cisco products being connected directly to the AC adapter.
View 5 Replies View Related