I am planning to buy new AP for my existing setup. we are using 1131AG series AP, we need to go for new one with n supported with external antenna.
Current software version on controller is : 7.0.235.3
Can Controller 4400 series work with Aironet 3600 series?
View 5 Replies View RelatedI've download a login.html into the controller successfully, but when I preview the page there isn't an accept button. Do I need to create the accept button with the html file or is there some place I need to enable on the controller itself. After download the .tar file I reboot the controller but no luck. I also create a java script button redirect but it didn't redirect to where I needed to go. It just stuck on the splash page.
View 3 Replies View RelatedWe are facing an issue with a customer where a Cisco 4400 Series controller is blocking the 802.11a/n Radio Interface of a 1250 AP. The radio shows as down on the controller GUI. The error message on the GUI is that the 'Regulatory Domain' is not supported. This can be seen from the attached screenshot. Also relevant parts of the WLC configs are attached. WLC: Cisco 4402 WirelessWLC Country: SADevice: Cisco Lightweight Access Point 1250 (LAP) is controlled through the 4402 Cisco Wireless LAN Controller (WLC)The operating system version of the LAP: c1250-k9w8-mx.124-18a.JA version of the WLC: Software Version 5.2.178.0 The problem is that the controller shows that the 802.11a/n Radio Interface in Radio Slot # 1 is always down , the customer tried to manually 'no shut' the AP interface from the console and it worked , but obviously this solution would not work as the configuration cannot be saved (LW AP).
View 12 Replies View RelatedI recently upgraded our controllers to the latest version 7 software, as I read this was one of the requirements to get them to connect. But I am not having any luck getting into a controller. Normally I plug them in to the network, they pop into the controller listed as something like AP5057.a844.xxxx and then I can finish configuring them, but a static IP on them, etc. This is the first of this model AP I have tried to deploy, so I am wondering what is different with these. or what I might be missing in the default config in the WLAN controllers. Niether of which are set to "Master" either.
View 10 Replies View RelatedI am running the upgrade tool on Aironet AP1230B-A-K9. I can't join the controller by using the upgrade tool. the error is "AP does not have Supported Radio". What radio is the upgrade tool or controller look for on Aironet 1200 series? This AP is running 802.11b. However, I have several APs which the same model is running on the same one controller. The controller is model 4402.
View 8 Replies View Relatedwhat are the series of access point that are supported without WLC. anteena should be in built and capability link 1130ag series.
View 9 Replies View RelatedI have 3 4400 WLC's that implemented at 1 main site within a mobility group. I am looking at implementing wired guest authentication with a splash page for username and password access. I have followed the documents and suggestions about how to configure it. I created a layer 2 vlan (700) and then created a VLAN (151) that wired guests will get an IP address from. I then configured a WLAN with the ingress interface being VLAN 700 and the egress interface being VLAN 151.
All of my controllers are running code 7.0.116.0. When I go to do a test scenario with a wired client, I have the switchport setup for VLAN 151, which they get an IP address from, but when they try to go to the Internet, they don't get the splash page. Why I am not getting a splash page or even if this scenario is possible?
Is the Cisco 850 series router supported with PoE-PowerInjector 800-PwrInj? In the 850/870 cabling guide I found a reference only 870 series would be supported.
View 2 Replies View RelatedI have a CiscoWorks LMS 2.6 and i would like to know if the new Switches Catalyst 2960-S Series are supported with this LMS version?
View 1 Replies View RelatedI wonder are 4500-E series line cards (i.e. WS-X4648-GB-RJ45, WS-X4748-UPOE+E and WS-X4606-X2-E) supported on 4507R chassis? Datasheet says "Classic line cards may be deployed in both classic and E-Series chassis with either classic Cisco Catalyst 4500 Series supervisor engines or with the Cisco Catalyst 4500E Series Supervisor Engine." But it says nothing about E-Series line-cards being (or not) supported on classic chassis (like 4507R).
View 3 Replies View RelatedI can configure two APs as a bridge with one as an AP with RMW enabled, and the other in WGB mode. I have three VLAN, each configured on both APs with their own SSID. Each switch (cisco switches) port is in trucking with only the three vlan allowed. The APs are associating with each other but not passing VLAN traffic.
View 8 Replies View RelatedOn autonomous AP's one can disable the bright status LED using the "led ....." command. But how can I disable the LED on a LAP-1131AG? The AP hangs in a bedroom so the light is quite annoying.
View 3 Replies View RelatedMy AP 1131AG is not light weight mode and not able to boot. I have captured logs from consle port it stuck up after following error:
Xmodem file system is available.
flashfs[0]: 9 files, 3 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
[Code].....
IOS of my LAP 1131AG is corrupted. It is giving error messages while booting and asks for boot image.
View 2 Replies View RelatedMy customer has an 1131AG AP, andhas Problems with joining to the controller. I did a debug and have the following output. The WLC (5508) shows the AP with Primary SW version as 3.0.51.0. this Release does not showup in any compat matrix! It seems to start downloading the software. after a while it stops with the bolded output, twice the same Bytecount!?
*spamApTask0: Apr 03 09:55:59.998: 68:ef:bd:94:e7:9c 5179392 Bytes Transferred to AP 68:ef:bd:94:e7:9c
*spamApTask0: Apr 03 09:56:00.097: 68:ef:bd:94:e7:9c Received LWAPP
[Code].....
I have succeeded in turning the AP from autonomous into LWAPP mode with the Ugrade tool. The AP has been loaded with c1130-rcvk9w8-tar.124-10b.jda due to the upgrade tool version 3.4,After reboot, the AP appears on the vwlc (YES!) however as you can see in APvwlc.jpg the AP now have version 3.0.51.0.I need the AP to be loaded with version 7.3.101.0 with FlexConnect mode.
View 24 Replies View RelatedI have a dozen clients on an 1131AG and they cannot ping each other. I get a reply but it says destination host unreachable.
View 4 Replies View RelatedWe have six 1131AG WAP's, lightweight, managed through a 2514 controller. We have a Windows 2008R2SP1 domain. Wireless users can connect to the network, and log on to the domain without any apparent 'issues'. They can access domain resources. However, they cannot browse the domain in Network Neighborhood. Interestingly, they can map a drive to shares on the servers, so long as they manually type in the path. This occurs with desktops running Windows 7 Pro, 32 and 64 bit; XP Pro SP1, 32 and 64 bit; ditto for laptops. The wireless NICs vary as to manufacturer, but do include Trendnet, Intel Centrino, and Intel Pro 100/1000. If I connect any of these machines via by wire, they can access all domain resources and browse the domain in Network Neighborhood in the usual manner.
View 3 Replies View RelatedI have WAP4410N and AP-1131AG for the school lab's Access point. First, WAP4410N doesn't make connection to wired network.
There's no DHCP server in our school and uses below :
192.168.x.x ip address
255.255.0.0 Subnet
192.168.1.254 Gateway
210.220.16.7 DNS address.
So I seted these settings on the configuration page, but when I connect to the WAP4410N wireless, I can't connect to the internet. Problem reporter in Windows 7says there's IP adress problem on the access point. ...but the ip address is correct. I did everything on the manual ....
Second, AP-1131AG. I entered with console cable and changed the ip address. And I enabled wireless radio(default:disabled) but I cannot find SSID with wlan. I added SSID on SECURITY-SSID manager. It says 'interface on' on 802.11a/g, but it is the same. I can't find SSID. other labtops can't, too.. tried using vlan. FAILED....
I have a Cisco 2106 WLC, and a 1131ag Access Point. The 802.11a/g Radio "Operational Status" = DOWN. All other Radios are UP. I'm wondering if this is normal behavior as no clients are connecting to it over the 802.11a/g Radio.
View 8 Replies View Relatedwe have the WLC and 2 x Aironet AP's that is powers over PoE. The other day is was reloaded and since then the AP points are Blinking Red, according the the Aironet manaul this means some sort of boot error? They are also not appearing on the WLC from the GUI or CLI running a show ap summary. Interesting though I can see them via CDP, however they are not picking up IP's as they are listed as 0.0.0.0. After checking with colleagues I was told these were set statically.
Is it possible that the points not having IP addresses is a sign of a corrupt boot environent? I would have though they would not have appeared in CDP if they were corrupt?
I did not set this up in the first place so a little puzzled at the moment? Nothing has changed on the config bar using a different NTP server on the network?
I can't figure out how to disable the syslog counter on my 1131AG WAP. See the below example log, the counter (number 3614) is right next to the hostname and increments with every syslog message:
Oct 25 07:31:10 airhead 3614: %DOT11-6-ASSOC: Interface Dot11Radio0, Station 7c61.93a4.8332 Associated KEY_MGMT[WPAv2 PSK]
I've tried both of the following commands, neither one removes the counter:
no service sequence-numbers
no logging count
Version Info:
Cisco IOS Software, C1130 Software (C1130-K9W7-M), Version 12.4(10b)JDA, RELEASE SOFTWARE (fc1)
BOOTLDR: C1130 Boot Loader (C1130-BOOT-M) Version 12.3(8)JEA, RELEASE SOFTWARE (fc2)
how to rid the syslog counter
I had deployed Fifty 1131AG AP with Cisco 5508 Controller, the problem is some APs giving a orange ligth and some of them didn't flashing "there Led is Off"
View 8 Replies View RelatedI have a problem with one of our 1131AG AP, B/G radio go down:
show controller dot11Radio 0:
(...)
Last radio reset code: 46
Radio resets - total:2946 retries:0 failed:0
Reset Stats: Start Cnt: 2742, Recovery: Cnt 33, Last Ret: 20, Fails: 0, Recvry Status: Stalled NO, In Prog NO
Code/Count: 37/00025 46/02851 51/00005 54/00030
Code/Count: 62/00001 67/00001 71/00033
Although I was not able to find any information about this reset code in Cisco documents. What is the reset code 46?What can i do?
How do I find out the IP address of a aironet 1131ag wireless router?
View 1 Replies View RelatedI have several AP's of 1131 AG used in autonomous mode. Recently one of them stops responding: i was not able to access web management or ping its NIC. I've tried with reseting device to default but no success, even more when i plug ethernet cable to AP port nothing happens even NIC led's are not blinking at all.
On CLI console i am seeing repeated constantly such entries:
*Mar 1 05:19:04.086: %LINK-3-UPDOWN: Interface BVI1, changed state to up
*Mar 1 05:19:05.086: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
[Code].....
( i have new firmware but how to upload it without this interface running ? )
I have configured my AP with MBSSID and it does work fine. now I need to take it to the next level and introduce the 2nd ssid to be my home guest network for friends and family that are visiting. What else should I include on this configuration to allow for a hot spot where the user logons and must authenticate themselves via a secure web browser before going out to the internet. Next question would be how to increase the security of the device and the AP.
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
[Code].....
I have a problem with three AIR-LAP1131AG-E-K9 that joined the controller and the status led turns to yellow after joining the controller while other LEDs are blinking green.The APs has no coverage at all although the WCS shows that there is coverage and the 4400WLC shows that the AP interfaces are UP. (The ethernet interface and tha 802.11b,g radio interface is up).The SSID broadcast is enabled.On the switch the interface is up and there is traffic going in and out of the LAP.I tired power reset and factory reset for the APs but the problem remains the same.
View 2 Replies View RelatedWe have multiple Cisco Aironet 1131AG devices, all wired on one Cisco L2 switch(2560) who is connected to L3 switch (3550). We assigned one VLAN for access point in L3 switch who acts as vtp server (L2 switch is vtp client). All ap's will have static ip address and all will have same SSID and no security and they will be using multiple channels (ex. 1,6,11). They will operate in 3 floor building for roaming wireless client. We won't using any wireless controller.
How to configure APs-all the same with different ip's, can we use L3 switch to create dhcp server for access points VLAN (pool for clients, and the rest for static ip for ap's)?
What's the main technical differences among the 1140 AP series and the 1260 AP series?I know that the 1260 supports external antennas while the 1140 supports internal antennas, but apart from that, is there any other important difference ?
View 10 Replies View RelatedIm using 1131AG AP.Locally switched WLAN don't have problem.Authentication used: open/wpa-psk/wpa2-psk.Pinging the IP Address of the vWLC dynamic interface (WLAN-SSID Mapping) is ok, but with the gateway failed.
View 12 Replies View RelatedOne of my customers asked me to configure a WLC 2106 and 2 LAP 1131AG (lightweight) for corporate/guest Wifi. Basically they want to implement a good wifi connection for internal use and a guest one with different QoS. The two lans should both have dhcp but they must bet kept segregated so that none from the Guest wifi can access corporate resources.
Since i've never configured a WLC from scrath i lightly supposed it would be quite straigh forward as routers and switches from Cisco.Unfortunately i was totally wrong.
I've downloaded the "Cisco Wireless LAN ControllerConfiguration Guide" (Soft.Release 6.0 June 2009) and after i red it i made up this workflow
for the configurations:
1) Configure Controller: (via serial)
- Set Management Interface parameters (IP- SM - Def GW - Dhcp server IP)
- Set Ap-Manager Interface parameters
- Virtual Interface parameters
- Set Admin Credentials
- Dhcp Configuration (internal and/or external)
2) Ap registration on the controller
- Configure vlan with dhcp request redirection to the dhcp server
3) Configure Wlan following customer's requests.
- Configure Wlan Auth for Corporate/Guest Wifi
- Configure QoS for both Wlans
Unfortunately i'm experiencing issue while trying joining the AP to the WLC.It appers that the IT guy of my customer tried to configure one of the Ap.In that Ap's flash i find files referring to a "mesh" configuration like: [code]