I have a Cisco 2106 WLC, and a 1131ag Access Point. The 802.11a/g Radio "Operational Status" = DOWN. All other Radios are UP. I'm wondering if this is normal behavior as no clients are connecting to it over the 802.11a/g Radio.
View 8 RepliesI have a problem with three AIR-LAP1131AG-E-K9 that joined the controller and the status led turns to yellow after joining the controller while other LEDs are blinking green.The APs has no coverage at all although the WCS shows that there is coverage and the 4400WLC shows that the AP interfaces are UP. (The ethernet interface and tha 802.11b,g radio interface is up).The SSID broadcast is enabled.On the switch the interface is up and there is traffic going in and out of the LAP.I tired power reset and factory reset for the APs but the problem remains the same.
View 2 Replies View RelatedI am having trouble keeping my computer connected to the internet...even though it says my signal strength from my wireless internet is excellent. every time i get online i put in my url and it loads the page but if i click on anything on that page it asks me to connect again even though my computer says im still connected.
View 1 Replies View RelatedI have a question, I have an ap (cisco 1130) that began to get the status light flashing orange and light Ethernet and radio are off.I did a factory reset and it was ok ... past 3 days the problem has happened again.I changed the ap with a new but the situation remained.I tested the wiring and everything is ok.the switch port is set up correctly.
View 11 Replies View RelatedWe have a root AP whose status light is showing solid red. We power cycled it and it still shows solid red. According to the Cisco documentation, this indicates a firmware failure. Unfortunately, we did not get Smartnet with this access points and instead opted for the limited lifetime warranty.
My question is: is there any way to fix the firmware via console? Whether it be through xmodem or what not. I ran debugs on the controller and can confirm that the AP is not communcating with the controller.
It is also weird that the mesh APs that were previously connected to this root AP show a solid red on their status lights and green for their RF LEDs. Shouldn't the status LED be flashing green-amber-red?
My wireless connection for my laptop is showing upas N on Win 7 but G on DIR-655 status page??? I'm confused. Am I getting N speeds/coverage or stuck with G. If G, why? I've tried wiping my wireless network config. on Windows and reestablishing it, but no change. The DIR-655 config page shows my machine connected at 54 Mbps and Type as G
View 8 Replies View RelatedSo I'm trying to fix gateway laptop running Vista. The computer can connect both wired and wirelessly to the internet just fine. Sadly that's all it does. It doesn't let you use IE/Firefox/Skype or video games or anything. Every program acts like you're not connected. All signs seem to point towards it working just fine. I'm at a loss and can't figure out what's wrong with it.
Also, the internet works just fine if you start in safe mode with networking. You can use IE/Firefox just fine. I've tried turning off proxies and such but there aren't any as far as I can tell.
OK, so just mooching around in the pages of my switch, a 24 port switch and it has in the logs:
268InfoMay 15 22:43:51NIMInterface 26 is Link Down
269InfoMay 15 22:43:51NIMInterface 26 is Link Down
270InfoMay 15 22:43:51NIMevent(39),intf(26),component(2), on non-existent interface
Now, correct me if I`m wrong but my switch only has 24 ports and two of those (23 and 24) are dual personality jobbies!?Where the hell is port 26? Where did it come from? and why did it need to show up only for the switch to realise that it doesn`t really exist?
I can configure two APs as a bridge with one as an AP with RMW enabled, and the other in WGB mode. I have three VLAN, each configured on both APs with their own SSID. Each switch (cisco switches) port is in trucking with only the three vlan allowed. The APs are associating with each other but not passing VLAN traffic.
View 8 Replies View RelatedOn autonomous AP's one can disable the bright status LED using the "led ....." command. But how can I disable the LED on a LAP-1131AG? The AP hangs in a bedroom so the light is quite annoying.
View 3 Replies View RelatedMy AP 1131AG is not light weight mode and not able to boot. I have captured logs from consle port it stuck up after following error:
Xmodem file system is available.
flashfs[0]: 9 files, 3 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
[Code].....
IOS of my LAP 1131AG is corrupted. It is giving error messages while booting and asks for boot image.
View 2 Replies View Relatedmy computer is a dell dimension 1100, with a Linksys WMP54G wifi card, running vista home basic.In the wifi thing in the notification area, it shows two wireless networks, One is my normal SSID (Lower Net), and one is "Unidentified network". They are both on one wireless connection (Wireless Network Connection 3). When i try to go on the internet, it says i'm not connected. i tried disconnecting from the unidentified network, but that disconnects me from lower net too.
View 13 Replies View RelatedI might have to reboot my operating system, I have a Cisco wireless router, so I have to reset it, and set it up again after i reboot my operating system?
View 8 Replies View RelatedMy customer has an 1131AG AP, andhas Problems with joining to the controller. I did a debug and have the following output. The WLC (5508) shows the AP with Primary SW version as 3.0.51.0. this Release does not showup in any compat matrix! It seems to start downloading the software. after a while it stops with the bolded output, twice the same Bytecount!?
*spamApTask0: Apr 03 09:55:59.998: 68:ef:bd:94:e7:9c 5179392 Bytes Transferred to AP 68:ef:bd:94:e7:9c
*spamApTask0: Apr 03 09:56:00.097: 68:ef:bd:94:e7:9c Received LWAPP
[Code].....
I have succeeded in turning the AP from autonomous into LWAPP mode with the Ugrade tool. The AP has been loaded with c1130-rcvk9w8-tar.124-10b.jda due to the upgrade tool version 3.4,After reboot, the AP appears on the vwlc (YES!) however as you can see in APvwlc.jpg the AP now have version 3.0.51.0.I need the AP to be loaded with version 7.3.101.0 with FlexConnect mode.
View 24 Replies View RelatedI have a dozen clients on an 1131AG and they cannot ping each other. I get a reply but it says destination host unreachable.
View 4 Replies View RelatedWe have six 1131AG WAP's, lightweight, managed through a 2514 controller. We have a Windows 2008R2SP1 domain. Wireless users can connect to the network, and log on to the domain without any apparent 'issues'. They can access domain resources. However, they cannot browse the domain in Network Neighborhood. Interestingly, they can map a drive to shares on the servers, so long as they manually type in the path. This occurs with desktops running Windows 7 Pro, 32 and 64 bit; XP Pro SP1, 32 and 64 bit; ditto for laptops. The wireless NICs vary as to manufacturer, but do include Trendnet, Intel Centrino, and Intel Pro 100/1000. If I connect any of these machines via by wire, they can access all domain resources and browse the domain in Network Neighborhood in the usual manner.
View 3 Replies View RelatedI have WAP4410N and AP-1131AG for the school lab's Access point. First, WAP4410N doesn't make connection to wired network.
There's no DHCP server in our school and uses below :
192.168.x.x ip address
255.255.0.0 Subnet
192.168.1.254 Gateway
210.220.16.7 DNS address.
So I seted these settings on the configuration page, but when I connect to the WAP4410N wireless, I can't connect to the internet. Problem reporter in Windows 7says there's IP adress problem on the access point. ...but the ip address is correct. I did everything on the manual ....
Second, AP-1131AG. I entered with console cable and changed the ip address. And I enabled wireless radio(default:disabled) but I cannot find SSID with wlan. I added SSID on SECURITY-SSID manager. It says 'interface on' on 802.11a/g, but it is the same. I can't find SSID. other labtops can't, too.. tried using vlan. FAILED....
I have an AE3000 dual band wireless adapter using the Win 7 Pro OS. At work our routers all use the same SSID, but utilize different channels. In terms of signal strength, the strongest signal is usually, but not always, one of the channels on the 2.4GHZ band (usually 11). However, in terms of speed of connection and lack of overcrowding, the best signal is invariably one the channels on the 5GHZ band (usually 161). My AE3000 will inevitably connect to the strongest signal (channel 11) even though it only slightly stronger than the signal on channel 161 and furnishes a much slower connection than that obtainable on channel 161. Is there any way I can "force" the AE3000 to connect via channel 161 rather than channel 11?
View 6 Replies View RelatedI am planning to buy new AP for my existing setup. we are using 1131AG series AP, we need to go for new one with n supported with external antenna.
Current software version on controller is : 7.0.235.3
we have the WLC and 2 x Aironet AP's that is powers over PoE. The other day is was reloaded and since then the AP points are Blinking Red, according the the Aironet manaul this means some sort of boot error? They are also not appearing on the WLC from the GUI or CLI running a show ap summary. Interesting though I can see them via CDP, however they are not picking up IP's as they are listed as 0.0.0.0. After checking with colleagues I was told these were set statically.
Is it possible that the points not having IP addresses is a sign of a corrupt boot environent? I would have though they would not have appeared in CDP if they were corrupt?
I did not set this up in the first place so a little puzzled at the moment? Nothing has changed on the config bar using a different NTP server on the network?
I can't figure out how to disable the syslog counter on my 1131AG WAP. See the below example log, the counter (number 3614) is right next to the hostname and increments with every syslog message:
Oct 25 07:31:10 airhead 3614: %DOT11-6-ASSOC: Interface Dot11Radio0, Station 7c61.93a4.8332 Associated KEY_MGMT[WPAv2 PSK]
I've tried both of the following commands, neither one removes the counter:
no service sequence-numbers
no logging count
Version Info:
Cisco IOS Software, C1130 Software (C1130-K9W7-M), Version 12.4(10b)JDA, RELEASE SOFTWARE (fc1)
BOOTLDR: C1130 Boot Loader (C1130-BOOT-M) Version 12.3(8)JEA, RELEASE SOFTWARE (fc2)
how to rid the syslog counter
I had deployed Fifty 1131AG AP with Cisco 5508 Controller, the problem is some APs giving a orange ligth and some of them didn't flashing "there Led is Off"
View 8 Replies View RelatedI have a problem with one of our 1131AG AP, B/G radio go down:
show controller dot11Radio 0:
(...)
Last radio reset code: 46
Radio resets - total:2946 retries:0 failed:0
Reset Stats: Start Cnt: 2742, Recovery: Cnt 33, Last Ret: 20, Fails: 0, Recvry Status: Stalled NO, In Prog NO
Code/Count: 37/00025 46/02851 51/00005 54/00030
Code/Count: 62/00001 67/00001 71/00033
Although I was not able to find any information about this reset code in Cisco documents. What is the reset code 46?What can i do?
Im trying to install the e2500 router on my sisters macbook, but it says it is an "unsupported operating system". She has operating system 10.8.1. Why am i not able to install It?
View 1 Replies View Relatedwpc11ver.3 / get driver for Ubuntu operating system?
View 2 Replies View RelatedHow do I find out the IP address of a aironet 1131ag wireless router?
View 1 Replies View RelatedI have several AP's of 1131 AG used in autonomous mode. Recently one of them stops responding: i was not able to access web management or ping its NIC. I've tried with reseting device to default but no success, even more when i plug ethernet cable to AP port nothing happens even NIC led's are not blinking at all.
On CLI console i am seeing repeated constantly such entries:
*Mar 1 05:19:04.086: %LINK-3-UPDOWN: Interface BVI1, changed state to up
*Mar 1 05:19:05.086: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
[Code].....
( i have new firmware but how to upload it without this interface running ? )
I have configured my AP with MBSSID and it does work fine. now I need to take it to the next level and introduce the 2nd ssid to be my home guest network for friends and family that are visiting. What else should I include on this configuration to allow for a hot spot where the user logons and must authenticate themselves via a secure web browser before going out to the internet. Next question would be how to increase the security of the device and the AP.
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
[Code].....
we have a couple of AP1262N-E-K9 access point with firmware version 12.4(25d)JA1 operating in autonmous mode.
I attempted to measure the signal quality between the APs by setting one device to repeater mode while all others are in root mode. Then, I execute the following command: dot11 Dot11Radio 0 antenna-alignment
1. The output of "show dot11 antenna-alignment" is incorrect, the % value represents the signal strength in dBm without the - (minus). E.g. "-25 dBm" is displayed as "Signal 25% 0 dBm".Now, I know that is only a display error but still this is not clean. Is this a known issue?
2. Why are the measured signal strength values not displayed on the SSH console during the antenna-alignment test? Is it obligatory to use the console to see these values? Or is it also a known bug which might be fixed in later firmware versions?
We have multiple Cisco Aironet 1131AG devices, all wired on one Cisco L2 switch(2560) who is connected to L3 switch (3550). We assigned one VLAN for access point in L3 switch who acts as vtp server (L2 switch is vtp client). All ap's will have static ip address and all will have same SSID and no security and they will be using multiple channels (ex. 1,6,11). They will operate in 3 floor building for roaming wireless client. We won't using any wireless controller.
How to configure APs-all the same with different ip's, can we use L3 switch to create dhcp server for access points VLAN (pool for clients, and the rest for static ip for ap's)?
Im using 1131AG AP.Locally switched WLAN don't have problem.Authentication used: open/wpa-psk/wpa2-psk.Pinging the IP Address of the vWLC dynamic interface (WLAN-SSID Mapping) is ok, but with the gateway failed.
View 12 Replies View Related