Cisco Wireless :: 1524SB - Have Root AP Whose Status Light Showing Solid Red
Jun 30, 2011
We have a root AP whose status light is showing solid red. We power cycled it and it still shows solid red. According to the Cisco documentation, this indicates a firmware failure. Unfortunately, we did not get Smartnet with this access points and instead opted for the limited lifetime warranty.
My question is: is there any way to fix the firmware via console? Whether it be through xmodem or what not. I ran debugs on the controller and can confirm that the AP is not communcating with the controller.
It is also weird that the mesh APs that were previously connected to this root AP show a solid red on their status lights and green for their RF LEDs. Shouldn't the status LED be flashing green-amber-red?
View 1 Replies
ADVERTISEMENT
Apr 14, 2010
I have a Problem with a ASA 5505 when i power on the ASA the Power LED change to green and the Status light to solid amber. There is no Console output or anything else.
View 9 Replies
View Related
Oct 14, 2011
I have an ASA 5505 with status light solid amber color. It is under SmartNet.I'd like to know Cisco will replaced this device with new ASA5505 or upgrade one?
View 2 Replies
View Related
Dec 5, 2012
I was having problems connecting to one of my usb devices that was plugged into my router. I unplugged the router to reset it and whenever it starts up it flashes green and the green light goes solid for less then a minute before turning red. It's a solid red light. I've tried unplugging everything and restarting it and nothing. Ironically it still lets me connect to the internet but when I access the control panel on my computer it shows as disconnected. Is this means my router is busted. This is my second Belkin Router and the only reason I had to replace the last one is because it was a G+Mimi router and I upgraded to an N Router.
View 3 Replies
View Related
May 7, 2012
I have a question, I have an ap (cisco 1130) that began to get the status light flashing orange and light Ethernet and radio are off.I did a factory reset and it was ok ... past 3 days the problem has happened again.I changed the ap with a new but the situation remained.I tested the wiring and everything is ok.the switch port is set up correctly.
View 11 Replies
View Related
Nov 20, 2011
I have a WRT300N and the power light is dim and all 4 ports are solid green along with the internet light being solid green.. Nothing else is plugged in.. Just the power.. I have tried to hard reset and nothing happens.
View 2 Replies
View Related
Feb 18, 2013
Region : Canada
Model : TL-WR1042ND
Hardware Version : V1
Firmware Version : 3.14.4
Recently in the morning the router will have lost ability to connect to internet <internet light is on> and I cannot access the router page <sys light solid> from either wired or wireless connections. Why is this and will it be solved if I upgrade firmware?
View 2 Replies
View Related
Dec 23, 2012
I have a DIR-615 v e3 router
Did a bad dd-wrt flash and now all it does:
-no power light
-solid green lights: WAN-L1-L2-L3-L4
tried to go to recovery mode (power on while holding reset switch).....does not work.my search on the internet revealed, that after bad flash, power light still comes on, maybe as orange, maybe blinking, or just blinks once
View 1 Replies
View Related
Oct 28, 2012
I've not found any topic related to what happened to me. Bought two cameras and upgraded the firmware on both as asked, but one of them just stopped. The light is solid green and not red like other posts.Tried the recovery procedure, but the browser won't find my camera. Changed computer IP and everything else that was told to be done. Nothing works!! I also can't find any posts relaled to my problem all over the internet.
View 3 Replies
View Related
Apr 18, 2013
A customer has a wireless PTP bridge using a pair of 1410 bridges. The non-root bridge event log shows the RSSI polling information message indicating the link's signal strength; ie. -42 dBm. It updates every few seconds or so. The root bridge does not show this information in the event log. Both bridges have the event log configuration options set identically, all messages types are enabled. I can't find any reference to this in the documents. Is this by design? I thought that maybe a root bridge if it was set up as a multi-point might be overwhelmed if it was showing/scrolling RSSI from multiple non-roots.
View 3 Replies
View Related
Oct 16, 2011
I have recently wiped my hdd and installed WinXp, I use to have vista but a crash occurred. I have WinXP SP3 with a Belkin Connect N150 connected to a Arris Telephony modem from Comcast. My setup use to work on vista. I've ran belkin setup from the disc multiple times and it gets to the part where it says connect and make sure cables are connected. All cables are connected, but my router has a solid amber light. I can access arris through wired internet, but I really want my wireless to work.
View 3 Replies
View Related
May 9, 2013
I cannot get access into my router because it doesn't seem to have a gateway IP address, although it is assigning my computer an IP address.
View 1 Replies
View Related
Feb 16, 2010
I have a Cisco 2106 WLC, and a 1131ag Access Point. The 802.11a/g Radio "Operational Status" = DOWN. All other Radios are UP. I'm wondering if this is normal behavior as no clients are connecting to it over the 802.11a/g Radio.
View 8 Replies
View Related
May 3, 2013
We have a problem with a Cisco 1400 Bridge. This equipment can not bridge to the other root or not root mode. I can see a message "Interface Dot11Radio0 Radio transmit power out of range" and the MAC Address of Dot11Radio0 appears with 0000.0000.0000.I set the local power to 18 but the MAC Address is still in 0000.0000.0000.
View 1 Replies
View Related
Oct 18, 2011
i got the problem with 1300 bridges,root bridge with omni antenna and non root with sector antenna , it can associate and can pin each other , but whenever i try to browse several web pages its get timed out and radio was down.
View 5 Replies
View Related
Nov 3, 2012
I am having trouble keeping my computer connected to the internet...even though it says my signal strength from my wireless internet is excellent. every time i get online i put in my url and it loads the page but if i click on anything on that page it asks me to connect again even though my computer says im still connected.
View 1 Replies
View Related
Sep 26, 2010
My wireless connection for my laptop is showing upas N on Win 7 but G on DIR-655 status page??? I'm confused. Am I getting N speeds/coverage or stuck with G. If G, why? I've tried wiping my wireless network config. on Windows and reestablishing it, but no change. The DIR-655 config page shows my machine connected at 54 Mbps and Type as G
View 8 Replies
View Related
Nov 27, 2011
Does a ASA5505 have a limited lifetime warranty? I have a ASA that is not covered on a SmartNet contract, as far as I know of, it is not owned by my company. It has a yellow status light, and will not boot. Will cisco replace it?
View 1 Replies
View Related
May 11, 2013
I have an older rev a DIR-655 that has served me well. Today I finally upgraded my ISP to cable (from a slower DLS connection) to get reasonable speed/price All is working very well but unlike my old DSL modem the internet status light on the DIR-655 blinks very rapidly all the time instead of when traffic is passed.The new modem is a Motorola SB6141,I am running the latest firmware 1.35NA I went through a complete re-setup to see if that would calm the light but no dice there. (the settings arrived at were basically the same for the old Sprint modem) ,Is there something I am missing or is it time to retire the old DIR-655 for something more current.
View 5 Replies
View Related
May 13, 2011
So I'm trying to fix gateway laptop running Vista. The computer can connect both wired and wirelessly to the internet just fine. Sadly that's all it does. It doesn't let you use IE/Firefox/Skype or video games or anything. Every program acts like you're not connected. All signs seem to point towards it working just fine. I'm at a loss and can't figure out what's wrong with it.
Also, the internet works just fine if you start in safe mode with networking. You can use IE/Firefox just fine. I've tried turning off proxies and such but there aren't any as far as I can tell.
View 11 Replies
View Related
May 16, 2011
OK, so just mooching around in the pages of my switch, a 24 port switch and it has in the logs:
268InfoMay 15 22:43:51NIMInterface 26 is Link Down
269InfoMay 15 22:43:51NIMInterface 26 is Link Down
270InfoMay 15 22:43:51NIMevent(39),intf(26),component(2), on non-existent interface
Now, correct me if I`m wrong but my switch only has 24 ports and two of those (23 and 24) are dual personality jobbies!?Where the hell is port 26? Where did it come from? and why did it need to show up only for the switch to realise that it doesn`t really exist?
View 2 Replies
View Related
Jul 18, 2011
Any working configuration between two BR1310's in Root/Non-root mode? The documentation is vary vague and i can't find anything more secure than WEP. Is it possible to use WPA with radius authentication?
View 1 Replies
View Related
Jun 17, 2012
On My modem the upstream and downstream lights show up normally but the light confirming the connection is not showing up.My modem simply can't connect and when I call My provider they just don't know the problem.
View 3 Replies
View Related
Jun 3, 2013
We have a deployment with six 1524SB mesh APs. Two are used as RAPs and face east and west respectively with directional antennas and two MAPs on each side with omni antennas. The RAPs are within 20 feet of each other. I set the bridge group name as east or west depending on which side of the mesh the equipment is located but noticed the downlink channel is set to 56 on both RAPs. I don't remember setting the channel for the RAPs, but they aren't using the global DCA.Would best practice be to change the downlink to unique channels on the RAPs, enable DCA (if it will let me), or is a unique bridge group name sufficient enough?
View 2 Replies
View Related
Jun 3, 2011
every now and then my Belkin brand router will just switch from green light, to red light. Sometimes unplugging it for a while fixes it, sometimes unplugging it for a LONG while fixes it, sometimes prayer and chanting fixes it. But most of the time the red light sits there mocking my efforts.What's making this happen? Is it my wireless security settings? Because I used to try and fix it by pressing/holding down the WPS button.
View 4 Replies
View Related
Mar 3, 2011
I have bought 2 white single ariel recievers for wireless xbox live and red light stays on both so cant be them so what am i doing wrong , i have had it working on a cable but not wireless
View 1 Replies
View Related
Feb 21, 2012
Network port: Yellow light blinking and orange light not showing
View 1 Replies
View Related
Apr 24, 2012
Can I associate the non-root bridge model 1310 to the root bridge model 1400? Is there any problems on the configuration I need to be aware of?
View 7 Replies
View Related
Mar 21, 2012
Someone has mentioned only 25 nodes are supported by the 1524SB and that one AP gets bogged down by 20 nodes or more.
View 0 Replies
View Related
Jul 22, 2011
I previously asked if I should be concerned that the Internet light on my Linksys E3000 router doesn't light up when I have Internet access. Well recently I had to do a reset and I noticed that during the reset it does in fact light up, but it doesn't come on when the router is done with the reset!
View 1 Replies
View Related
Jul 12, 2011
I'm trying to connect a PC to my wireless network but am having issues. Using both a trendnet wireless N PCI network card and a Linksys G510 wireless G PCI network card I have the same issue whereby the connection, an unprotected mixed (B,G,N but have tried only N on the trendnet) wifi, appears in the Windows 7 connection list but upon clicking "connect" I am told Windows was unable to connect to the network, and then the network dissapears. Later on, it will randomly appear and will stay as such until I try to connect.
I've tried using an Asus wireless N 150 USB adapter with the PC, the problem is different. I can connect to the network and the connection will appear fine in the taskbar, but trying to open a webpage either does not happen or is excruciatingly slow.
View 1 Replies
View Related
Jan 18, 2011
Recently we had a situation where our users were unplugging one of our un-mounted 1252 LAPs. They would do this so they could borrow the wire to direct connect any one of their devices not realizing they were disconnecting a wireless access point. After discovering that the AP was unplugged once again, our admin plugged the AP back to the network but noticed that it no longer would connect to the controller. We can no longer console into the AP but can console into all other APs we have. All 3 lights are now green. Radio and Ethernet are solid and Status is blinking. I found the Cisco doc explaining the meaning of the front panel lights but have not found this particular configuration. What these lights mean and why not being able to use the console port?
View 11 Replies
View Related
Aug 21, 2011
My e1000 router (v 2.1) has reset itself and after that all lights except the wireless adapter has gone solid blue, I have no ethernet conectivity and hard reset the router did not work.
View 9 Replies
View Related
