On My modem the upstream and downstream lights show up normally but the light confirming the connection is not showing up.My modem simply can't connect and when I call My provider they just don't know the problem.
View 3 Repliesevery now and then my Belkin brand router will just switch from green light, to red light. Sometimes unplugging it for a while fixes it, sometimes unplugging it for a LONG while fixes it, sometimes prayer and chanting fixes it. But most of the time the red light sits there mocking my efforts.What's making this happen? Is it my wireless security settings? Because I used to try and fix it by pressing/holding down the WPS button.
View 4 Replies View RelatedI have bought 2 white single ariel recievers for wireless xbox live and red light stays on both so cant be them so what am i doing wrong , i have had it working on a cable but not wireless
View 1 Replies View RelatedI was having problems connecting to one of my usb devices that was plugged into my router. I unplugged the router to reset it and whenever it starts up it flashes green and the green light goes solid for less then a minute before turning red. It's a solid red light. I've tried unplugging everything and restarting it and nothing. Ironically it still lets me connect to the internet but when I access the control panel on my computer it shows as disconnected. Is this means my router is busted. This is my second Belkin Router and the only reason I had to replace the last one is because it was a G+Mimi router and I upgraded to an N Router.
View 3 Replies View RelatedNetwork port: Yellow light blinking and orange light not showing
View 1 Replies View RelatedI have a question, I have an ap (cisco 1130) that began to get the status light flashing orange and light Ethernet and radio are off.I did a factory reset and it was ok ... past 3 days the problem has happened again.I changed the ap with a new but the situation remained.I tested the wiring and everything is ok.the switch port is set up correctly.
View 11 Replies View RelatedWe have a root AP whose status light is showing solid red. We power cycled it and it still shows solid red. According to the Cisco documentation, this indicates a firmware failure. Unfortunately, we did not get Smartnet with this access points and instead opted for the limited lifetime warranty.
My question is: is there any way to fix the firmware via console? Whether it be through xmodem or what not. I ran debugs on the controller and can confirm that the AP is not communcating with the controller.
It is also weird that the mesh APs that were previously connected to this root AP show a solid red on their status lights and green for their RF LEDs. Shouldn't the status LED be flashing green-amber-red?
I am trying to find a way using CLI that I can identify the amperage being used by a 6509 chassis. I have looked through all of the sh power and sh env commands and seem to only find the power being used on the DC side (since the output referemces 42V). Ddint know if there was something I was overlooking. To each things from the AC side will take getting an electrician in which is what I was hoping not to have to do.
View 4 Replies View RelatedHandPunch 3000 Time & Access Device, no Communication over the Ethernet, on the Ethernet Card the red light flashes for 1sec then red & Green for 1sec.
View 1 Replies View RelatedThe send light is steadily blinking. Yesterday I disconnected the cable into my main cable box connected to my tv, so I could move it into a new tv stand I bought, and ever since then I get no Internet connection (tv cable works fine.) I cant see how that made my Internet go out, but maybe it did. I checked connections on both ends and all cables are tightly secured.Here is a log of my modem, I found out how to get it through this site.[CODE]
View 5 Replies View RelatedI have Qwest DSL 7MB internet with a motorola 3347 Qwest model modem and for some reason throughout the day sometimes fewer than than others my internet light will just go red for about 45 seconds up to 2 to 3 minutes them it starts flashing green again? I called them multiple times but they just say maybe its the modem. Is there any test I can do to see? I upgraded the firmware to the newest one to see if that would work but no luck.
View 1 Replies View RelatedI recently purchased the Linksys Wireless N Home WAG120N and I've hooked it up correctly but I can't seem to establish a connection with the DSL light. I've tried hooking it up to different ends in my house with no improved results, however, my older modem works fine.
View 1 Replies View RelatedBelkin n wireless router model number F5D8236 v1! my modem is showing an internet connection but my router "modem" light is flashing orange and my internet light doesn't even come on. we are not sure but we believe this became a problem last night after my daughter connected her new lap top to the wireless connection.
View 1 Replies View RelatedRegion : UnitedStates
Model : TD-W8960N
Hardware Version : V3
ISP : Centurylink
I am replacing my qwest/centurylink actiontec q1000 with the td-w8960n. I have run all the different setups, with the different settings that I have found on the net but to no avail. The one thing I have noticed is that the light for the asdl on the td-w8960n does not come on, but yet when I plug it back into the actiontec it sees it and the internet works. Any reason why the td-w8960n is not recognizing the active dsl line?
I previously asked if I should be concerned that the Internet light on my Linksys E3000 router doesn't light up when I have Internet access. Well recently I had to do a reset and I noticed that during the reset it does in fact light up, but it doesn't come on when the router is done with the reset!
View 1 Replies View RelatedThe internet connection light is blue, i am assuming this means the device thinks that it is connected. However wired or wireless I can't hit any web pages. When I use the internal tools neither can the device ping any address.
I am using:
Firmware 2.00NA
DSL modem ATT-Yahoo-SBC (Speedstream 4100 using DHCP)
I am planning to upgrade the firmware to 2.01NA and give that a shot.
Just bought the linksys E2500 as an upgrade for a my Trendnet 150 wireless N router. I have a motorolla surfboard modem with time warner roadrunner cable internet. After connecting the router I have no internet connection. I do not get a light on the WAN connection after the ethernet cable is attached. I know the light works because when I power it on all the lights come on. I cloned the MAC address but this did not work. I have searched the forums for hours and tried different ideas to no avail. My PC recognized the router and I'm able to get to all the settings but cannot establish a connection from the router to the modem. I also tried different ethernet cables to eliminate that possiblilty.
View 4 Replies View RelatedI have had a Dlink dir 615 for some time now and always had a few issues, but nothing a reboot of the router couldn't solve. This time the problem is persisting, though. The wireless signal keeps blinking and on my laptop it says No internet connection. I've rebooted the router, restored the router, rebooted the modem, and nothing seems to work.
View 1 Replies View RelatedI am trying to light up every port light on a 3750g. There is not anything plugged into them and I would like to know (just for fun) is there a way to make every port light 1 - 48 turn on using a command?
View 3 Replies View RelatedYesterday I bought the Linksys Wireless-N Home ADSL2+ Modem Router WAG120N (Annex-A version). I configured the modem/router and it was working very well. Today I was surfing the internet just fine and I left my computer for a few minutes, when I came back I noticed that there is no internet connection. The internet light on the modem was no longer on, and the DSL one was blinking. I turned off the device and then turned it back on but the issue was still present. I tried restoring the factory default settings and configuring the modem again but nothing seems to work (resetting the modem, turning off every device connected to it and restarting the modem/router). The DSL light keeps blinking, turns off for a couple seconds and then starts blinking again. The internet light only appears when I restart the modem and it flashes red just after turning the device on.
View 8 Replies View RelatedI recently switched from a DSL ISP (Earthlink, Zyxel modem configured as a bridge, pppoE connect) to a cable ISP (Comcast, Arris cable modem, dhcp connect). Basically PC --> DIR615-->Cable modem-->Internets. With the old DSL the Internet activity LED (green, looks triangular) on the DIR615 blinked only when internet activity occurred. With the new Comcast connection it blinks non-stop about 5 times a second! Even if the PC is turned off it blinks. It stops blinking if I disconnect the ethernet cable between router and modem. The connection itself is fine, but if the DIR615 is doing something it should not be doing it might slow the connection down a bit, (or burn something out prematurely?)FYI, the Arris cable modem does not seem to be a router. It takes a cable connection from outside and provides a single ethernet cable and 2 (voice) telephone cables to the house.
View 1 Replies View Relatedi formatted my pc but after that lan is not showing in network connections
View 1 Replies View RelatedI reset my dlink 615 and used the disc to do the set up.when finished my laptop worked fine, but very little on our ipad 2.I changed the channel from auto to manual and set it on channel 11. now the ipad 2 works on most things, emails,apps to ebay,my banking and most games that require internet acess. but when you try to go on Safari it says it can't connect to Google because there is no internet connection.
View 1 Replies View RelatedI'm standing beside my wireless access point with my laptop. It shows full signal in my laptop but I cannot connect to internet. I clicked on the view available networks and then the SSID names, typed my network key, and clicked "connect". It keeps on connecting, connecting and finally disappears and WAN connection remains with crossed mark. But it shows full signal in laptop and I'm standing beside the WAP.
View 4 Replies View RelatedMy wireless netwok indicator on the bottom of my screen show no connection. It says I need the WEP key.
View 1 Replies View RelatedI have 100mbps connection but when i took the test at speedtest.net it was so slow i don't understand whats bottle necking my system. When i download games off of steam it downloads its much faster then downing anything from my browser. I know its my network because when i went on steam and changed my download settings to cable and it was fixed.
View 9 Replies View RelatedI recently moved and changed computers, but ive been trying to setup my Linksys WRT150N. I had one cable coming from the modem and into the port on the router labeled "internet" and then another cable coming from one of the router's ethernet ports, going into the PC.
I opened a browser and typed in 192.168.1.1 into the address bar and got to the setup page. When I search for wifi using either my laptop or my droid, it shows that there is an excellent signal and will connect to it, but when I try to perform a task that would require internet, it says that there is no internet access.
I have a Toshiba Satellite A665 Model Laptop. Which i bought 2 years back. I got a new wireless Internet connection few days back. but I am unable to use that network in my laptop. I have Windows 7 Ultimate 64 bit OS in my system.
View 2 Replies View RelatedI have a Laptop : Hp Compaq nc6220, My wireless connection is showing but not connecting
View 1 Replies View Relatedmy computer is a dell dimension 1100, with a Linksys WMP54G wifi card, running vista home basic.In the wifi thing in the notification area, it shows two wireless networks, One is my normal SSID (Lower Net), and one is "Unidentified network". They are both on one wireless connection (Wireless Network Connection 3). When i try to go on the internet, it says i'm not connected. i tried disconnecting from the unidentified network, but that disconnects me from lower net too.
View 13 Replies View RelatedThe link to Local area connection on the PC i am working on is no longer showing under Network and Sharing center. However the connection is up and I can access the internet. If I do an ipconfig /all I see the adapter setting as I set them. In device manager the device is working properly. I checked the BIOS and the NIC is enabled
View 4 Replies View RelatedMy wireless connection for my laptop is showing upas N on Win 7 but G on DIR-655 status page??? I'm confused. Am I getting N speeds/coverage or stuck with G. If G, why? I've tried wiping my wireless network config. on Windows and reestablishing it, but no change. The DIR-655 config page shows my machine connected at 54 Mbps and Type as G
View 8 Replies View RelatedI have Roadrunner Turbo and when it's online it works fantastic but after a couple hours or a days the modem loses it's connection for 30 minutes to many times a whole day or two.
When it loses it's connection I've tried disconnecting the modem and the router, waiting a minute and plugging it back in. I've tried reconnecting the cable wire and nothing works. I've even tried going to the TWC center and replacing the modem with a new one and it still happens.
The router I have is a WNDR3700 and it works great. We never lose connection to the router but the modem will lose its connection for when this happens the router's usual lights are on and we are all still connected to the router but the modem has only 2 solid lights and 1 blinking one.