Linksys Wireless Router :: E2500 - No WAN Light Or Connection?
Dec 4, 2012
Just bought the linksys E2500 as an upgrade for a my Trendnet 150 wireless N router. I have a motorolla surfboard modem with time warner roadrunner cable internet. After connecting the router I have no internet connection. I do not get a light on the WAN connection after the ethernet cable is attached. I know the light works because when I power it on all the lights come on. I cloned the MAC address but this did not work. I have searched the forums for hours and tried different ideas to no avail. My PC recognized the router and I'm able to get to all the settings but cannot establish a connection from the router to the modem. I also tried different ethernet cables to eliminate that possiblilty.
View 4 Replies
ADVERTISEMENT
Aug 18, 2011
I have just upgraded my Linksys router from an older one to the E-2500 about a week ago. Everything is working great on my wired desktop and 3 wireless laptops except the printer will no longer work from any of the computers. I've checked the printer wireless settings and they are correct (ssid and password) and it says it's connected to the wlan. Each of the computers shows the printer is active and set to default BUT the port light on the back of the new router is not on. I have changed cables and still no light, the printer is set up for sharing and it did work a couple days ago but port light was on then.
I have not added anything that wasn't hooked up on my old router, I"m just trying to get what I had on the old router to work on the new one. Everytime I call support, they have me change something that messes up what a previous agent had me do. Now they want me to pay for a direct connection so they can upgrade my router firmware...they didn't even ask what version I already had which happen to be the same version that is available on [URL] so if I had agreed, I would have paid for nothing. I had already paid $29.99 for additional 14 day support on my old router only to find out I needed a new one.
I've been using Linksys routers for quite awhile but I'm just about ready to change brands. I would really like to give this E-2500 a chance.
View 1 Replies
View Related
Nov 8, 2012
I have a Linksys E2500 and recently the power led light on the back of the router started blinking. The router itself seems to be working fine. I can access the router and the router seems to be assigning the IP addresses fine. I did look up the issue on the knowledge base and tried all the solutions but the light is still blinking. Not sure what to do anymore.
View 5 Replies
View Related
Jul 22, 2011
I previously asked if I should be concerned that the Internet light on my Linksys E3000 router doesn't light up when I have Internet access. Well recently I had to do a reset and I noticed that during the reset it does in fact light up, but it doesn't come on when the router is done with the reset!
View 1 Replies
View Related
Dec 8, 2011
I purchased an E2500 router today and it worked perfectly for about 4 hours. Now it drops my internet connection constantly. I can connect and load maybe 2 pages before that little yellow triangle of doom appears. Then after 2 or 3 minutes I am good and can reconnect. This cycle just keeps happening.
View 1 Replies
View Related
Oct 7, 2012
Currently running Windows 7, with internet explorer. I have most recent firmware installed on my e2500. The unit drops wireless connectivity on an intermittent basis. Sometimes after 5 minutes and sometimes after 20 or 30 minutes.
View 9 Replies
View Related
Jul 13, 2011
I just purchased a E2500 wireless router to upgrade from the previous G- router which I was using. I'm not very experienced in tech issues and would like to know, what would be the easiest way to extend my wireless signal through out the house. The E2500 which I just purchased does not cover all the areas in my household.
View 1 Replies
View Related
May 12, 2013
I've been having issues with my e2500 router. I've found my connection dropping occasionally both with a wired connection and wirelessly on other computer. My desktop is connected directly to the router via ethernet and I've been keeping an eye on my network preference pane. Every 10 minutes or so the connection will be lost and computer says the cable is unplugged. It then resolves after 2 minutes.
I'm running OSX 10.8, firmware 1.0.07. Done a factory reset, power cycles etc. Configured with Cisco connect and manually multiple times. I've swapped out ethernet cables just to be sure it wasn't a cable issue.
Internet is fine when I've got the computer hooked up directly to the modem. No connection issues.
View 5 Replies
View Related
Nov 21, 2011
I have a Linksys E2500 Firmware Version: 1.0.03 and am using the "IPSec Passthrough" for work. On a typical day I'll sign in to my work's VPN, do my work, sign off in the evening, and read my personal email with a direct connection to the internet.
Then on the next morning, I am unable to connect to work until I go to http://192.168.1.1/index.asp and click "reboot." And as soon as the modem finishes rebooting, my laptop can connect to work. I've tried this several days in a row now, and indeed all I need to do to get the VPN passthrough working is rebooting the modem.
Nothing under "Applications & Gaming" is set. I've seen some posts about having a trigger on UDP port 500, but I'm not quite sure how to translate it for the E2500. Plus I'd rather the router "just work" day after day for VPN and everything else, like my old router did! Is there some other setting to try or clearer directions for a bulletproof IPSec passthrough on that unit?
View 7 Replies
View Related
Aug 12, 2012
I already have a desktop and modem at home, but I recently bought a new Sony Vaio laptop for college. I also bought a Linksys E2500 wireless router so my laptop could have internet access at home.I inserted the Starter Guide CD into my desktop, created my ID/password, and connected all the cables like it instructed me to but I still couldn't connect to the internet. Instead, several windows popped up with messages like, "Found new hardware. Locate and install driver software, "Insert disc that came with Internet Access Server", and "Windows could not find driver software for your device."When I tried to troubleshoot, I get something like this, "There may be a problem with your DNS - Windows attempted to find www. microsoft.com using DNS, but server responded back with unknown."I also tried inserting the disc into the laptop, but I still didn't recieve any internet connection, but it says that my router was connected.I tried following its advice to restart, unplug cables, and wait 2 minutes but none of it seem to work.
View 3 Replies
View Related
Feb 18, 2012
I recently purchased a linksys E2500 for my home network. Occassionally, we have dropped connections, on both G and N cards.The router is connected to a corei3-2100 cpu with 6 gb ram and a 1tb hd, running win7 64bit. Ive bought home plugs for my wife's computer(in the house)and.an outdoor wireless antenna (a CCRANE super usb wifi antenna) for my computer in the garage. I still get dropped signals in the garage, which is only about 50 ft from the router. My computer in the garage is an AMD dualcore 4400 with 4 gb ram, and multiple hdds.What else can I do to get a better and more constant connection.
View 1 Replies
View Related
Feb 5, 2013
I just bought a new Linksys E2500 router from Best Buy and I need optimizing my router settings so I can get the absolute best performance out of it. Staying connected and keeping speeds high are a must.I have been noticing connections cutting out at time. It is frustrating when I lose my internet.we have ~3000 sq foot house... 3 levels (basement, first, second).We don't use all of these at the same time but we have: 2 laptops, 3 iphones, ipad, and a PS3 for online gaming.
How can I get the absolute best, most reliable connection and speeds out of my router so we don't experience disconnects?I bought the RE1000 range extender... having installed it yet because the install CD that came with it is the wrong CD (It came with the E900 install CD... which is for a router)I bought the N600 USB adapter which I guess is supposed to update your wireless card for your laptop. I am using that but bars seem low..
View 9 Replies
View Related
Apr 11, 2012
We are using a domain and Windows Server 2008 machine with DNS/DHCP setup and active to handle traffic on the network. The old router we had was a cheap (~$20) TrendNet that was configured (not by me) without issue to not only allow the server to handle IP's but also allow us to get in to the server remotely via Remote Desktop. My cut sheet says they had a "virtual server" setup.
Anyways, we now are running an E2500 and if I put in the external IP, Subnet, Gateway, and DNS for our internet provider and then disable DHCP on the router, we don't get internet access. I'm missing what configuration I need to get the server to handle all the traffic I guess. The server has DHCP enabled with the router IP address (192.168.1.1) set and the server address is (192.168.1.2). Like I said before it was working fine with our old router and none of the settings on the server have been changed so must be something with the new router.
Do I need to setup something in the advanced routing to get this working? Currently I have DHCP on automatic and DHCP server enabled just so we can get internet access. DHCP services on the server are still on as well. Can't get any access to the server from the outside via Remote Desktop like we could before.
View 9 Replies
View Related
Dec 27, 2011
I have an E2500 with the latest firmware upgrade (1.0.03). My configuration is simple, I have a fixed IP from my ISP with fixed DNS servers. I have one computer connected via cable and one connected via wireless and a laptop that gets connected on occasion wirelessly as well. I also have an android phone that I sometimes have the networking turned on and sometimes not. That doesn't seem to be affecting the router either as I've lost connections under both circumstances. The only thing I have different is I clone the MAC address as the ISP has my IP linked to my old Linksys MAC.
The problem is I randomly lose connection to the internet, the home network is still up it's just the internet goes down. I could be on the computer or not, sometimes while browsing sometimes after I browse for a while sometimes before I get started. Fortunately its not happened during one of my online games but it has happened just after I log off the game. It usually happens a couple of times a day.
View 6 Replies
View Related
Feb 24, 2013
I'm using an E2500 router and an EA2500 adapter (to update my desktop from 802.11 g connection to 802.11n). I've connected my notebook to the network and the connection speed for the notebook is approx. 5.5 Mbps compared to 21.5 Mbps for the desktop connection. why the notebook connection is so much slower?I've just reinstalled both the E2500 and EA2500 tonight. I'm not sure whether or not there was such a vast difference in speed between the two before the reinstallation.
View 4 Replies
View Related
Jan 10, 2012
Just replaced a WRT54GS with an E2500. It seems that anytime a connected device goes "idle" for a while, the connection breaks or severely reduces and it's nearly impossible to get the connection back without performing an action at the device in question. Let the wireless connection on my laptop go unused for some period and it reduces to 1Mbps and you can't get back on by just using the link more... you have to do a "repair".
Let more than a few minutes pass since you've printed something on the wireless printer and you MUST go to the printer to re-establish the connection by turning the antenna off and then on again.Basically the same problem with my blueray/DVD getting on the network. When I shut the screen off on my phone, the wifi dies and receives NOTHING over that link while the screen is off.
None of these behaviors existed with the WRT... just the 2500. Background/facts - current firmware, DHCP with reservations, WPA2/per, MAC filtering in use, UPnP disabled. MTU/Beacon/Frag threshold/RTS threshold set per recommendations on this site.
View 2 Replies
View Related
Aug 4, 2011
here is what I have:
A) Sonic Wall @ 192.168.1.215
B) Linksys Switch (WRW248G4P) @ 192.168.1.254
C) Linksys Router (WRT160N) @ 192.168.1.202 (Disabled DHCP Server)
D) Linksys Router (E2500) @ 192.168.1.203
E) Windows Server 2003 @ 192.168.1.200
F) There is also a Router @ 192.168.1.201 that runs DD-WRT that has an enabled DHCP Server.
It goes something like this
i) A - B --ETHERNET-- E
ii) A - B --ETHERNET-- C
iii) A - B --FIBER to another building, then ETHERNET -- D
Everything connects to the internet, but (D) on (iii) doesn't allow connection to the server (E). What can I do to make this work?
View 1 Replies
View Related
Jul 29, 2011
I have a new e2500 router and want to use my old WRT54G2 to expand the range of the wireless to reach my detached garage. My house is wired with category 5e cabling, but not the garage, which is why i want to wireless to get expanded. I was hoping the the new e2500 would reach, but it doesn't. How I can do that?
View 6 Replies
View Related
Jan 6, 2012
my E2500 drops the internet connection randomly. I have no issues with wired or wireless access to the home network (sharing files, sharing printers etc...). To fix the problem I log into the router and do a soft reboot from the status page.
I posted this earlier and the only response I received was a cut and paste answer to make some changes to my wireless settings. Seriously doubting the relevance of the post I made the changes anyway and as expected nothing changed, the router still loses access to the internet without any warning. When I replied that I hadn't thought that that was the problem but that I HAD made the changes mentioned and as I expected it DIDN'T work I get no response.
View 9 Replies
View Related
Jan 18, 2012
I am using the E2500 v1.0 on TWC network (road runner) wit a VISTA upgraded to Windows 7 laptop.After few months the router is starting losing connection. I tried connecting my laptop directly to the twc modem and the connection is fine, while if I connect to the E2500 v1.0, through wired or wireless connections, I see that the connection is going back and forth.I tried resetting the modem and the router, upgrading the wireless router firmware, but nothing worked.
View 1 Replies
View Related
Mar 26, 2012
I'm constantly losing wifi connection and having to restart my Linksys E2500 router
View 4 Replies
View Related
Jan 22, 2012
Purchased E2500 1 week ago. I do not have a problem communicating with the router itself (either hard wired or wireless) but I have been unable to establish a usable internet connection from the router.I live in building that is wired by Restech Services - Ethernet jack in wall - no modem. Connection works just fine if I bypass router and connect directly to PC (windows XP SP3 desktop or windows 7 laptop.),Very difficult to establish any internet connection at all. I have to renew IP address many times or go through re-boot sequence multiple times. Once I get a connection it is unusable. If I attempt to ping a URL (either from PC or from router admin page) it is unable to resolve host. If I ping an IP directly (either from PC or router administrator page) I typically get 60 to 80% packet loss. As noted, if I bypass router and make internet connection directly to PC - no problems - no packet loss.Used Cisco Connect software to set up. On advice of ISP changed MTU from 1500 to 1300. Also registered MAC id with ISP and changed from cloning PC MAC to using the router MAC. Downloaded and installed latest firmware version. Did factory reset and re-configured the whole thing. Double checked and swapped wiring.
View 5 Replies
View Related
Apr 8, 2012
I did some testing with a few wireless N routers and then decided to buy a Linksys e 2500 as it was on a special for $66 in Australia.The wireless routers i tested were (Belkin brand new model / Netcomm & Dlink Used ones)1. Netcomm N800n Fastest wireless transfer speed 9MBytes or 72 MBPS.2. Dlink - Around 6MBytes/s or 48MBPS.3. Belkin - Around 4-5 MBytes/secDid not test the Linksys before buying it.4. Linksys E 2500 - around 5MBytes/s = 40MBPS.After all this testing, got a new Linksys believing that a cisco device should have good quality.My problems is that the connection speed on the device stays a 72BPS whereas on the Netcomm / D-link it used to be 130mbps. Not that this bothers me, however the file transfer speed matches the Link status connection speed.The router was placed at exactly the same location, file transfer was checked by transferring large file sizes.Lan setup is1. Belkin ADSL 2+ (Modem with Wireless b/g and Voip) only being used now as an ADSL Modem and VOIP service.2. Cisco linksys e 2500.3. Media centre PC which has a wired connection to linksys e 2500.4. Main PC (Connected wireless to the linksys). The network adapter is a DLINK DWA125 N150 adapter (2.4GHZ only). The distance between the wireless adapter and the wireless router is approximately 12 feet and there is direct line of sight.5. IPAD.5. Using 2.4GHZ as i dont have a 5GHZ adapter yet. Router is only on wireless N mode.I was better off using a second hand Netcomm rather than a brand new Cisco router. The cisco router has 4 internal antennas, whereas the netcomm one had only 2 external antennas. My signal strength is excellent. Only problem is the slow internal transfer between the Main PC and the Media Center PC. Main PC is Core i7 950 where as the Media Centre is a Core 2 Duo e6400GHZ with 4GB Ram. Both PCs running Windows 7 Ultimate (Main PC) , Professional (Media Centre PC). My network knowledge is decent. Is there any settings in the advanced Wireless mode for the Linksys that can make my internal file transfers faster. [code]
View 4 Replies
View Related
Aug 28, 2012
Yesterday I bought the Linksys Wireless-N Home ADSL2+ Modem Router WAG120N (Annex-A version). I configured the modem/router and it was working very well. Today I was surfing the internet just fine and I left my computer for a few minutes, when I came back I noticed that there is no internet connection. The internet light on the modem was no longer on, and the DSL one was blinking. I turned off the device and then turned it back on but the issue was still present. I tried restoring the factory default settings and configuring the modem again but nothing seems to work (resetting the modem, turning off every device connected to it and restarting the modem/router). The DSL light keeps blinking, turns off for a couple seconds and then starts blinking again. The internet light only appears when I restart the modem and it flashes red just after turning the device on.
View 8 Replies
View Related
Jul 16, 2012
A couple days ago, our Linksys E2500 router accidentally got unplugged. Since then, the internet has been working extremely poorly (a lot of latency issues plus random disconnects), so yesterday we tried soft resetting the router. This backfired immensely as now the network no longer exists and we can't access either the router or the internet through the router.If we have an ethernet cable go from the modem directly into a computer, the internet works fine (which is how I'm posting). But if we hook the modem up to the router and then another cable from the router into a computer, we get nothing. We can't even see the router.We've tried unplugging the modem and router and then plugging them back in, unplugging just the modem, and unplugging just the router to try to get it back working but that didn't work. We then tried holding down the reset button on the bottom of the router for fifteen seconds then unplugging the modem and router, holding down the reset button with the modem already disconnected then unplugging the router and plugging the modem back in then the router, and holding down the reset button with the modem already disconnected then plugging the router back in then the modem. And then we tried each of these things while waiting a minute before plugging everything back in. Nothing's worked. And everything we've googled to find out how to hard reset the router either says to do something I've already listed or requires using the router's configuration page, which we can't access (supposed to be 192.168.1.1, but nothing comes up when I enter that into my browser since we can't connect to the router).
View 14 Replies
View Related
Oct 6, 2011
After a recent lighting strick close by I can not connect to the internet through my router. Stright from the modem works fine. The port light on the router does not come on. I rebooted modem, router and computer with no luck. It's like I've lost my network adapters and I don't know how to get them back. I tryed another E2000 and it's the same way.
View 1 Replies
View Related
Jun 25, 2011
The Internet LED does not light up when I have access to the Internet like now. I think I remember this lighting up in the past and find it strange that an LED light would burn out so early
View 5 Replies
View Related
Jun 22, 2012
Reset button pushed in, unplugged won't reset it. I get my default name on connections but it's not showing as available connection.
View 7 Replies
View Related
Jan 24, 2009
Ive recently tried to update the firmware and everything went as instructed, then the power and LAN light went out. Now I have the indicator lights for the computer and modem, but thats is. No internet or SSID broadcast. I cannot log into or ping the unit, and have tried the hard reset many times, with no effect.
View 8 Replies
View Related
Dec 5, 2011
I just purchased the E4200 (hardware version 1).Great router with amazing features.I plugged my WD Elements 2TB, setup my media and FTP server and everything is working fine.
My only concern is about the HD light that is always on, even when nobody is accessing it. I turned off the Auto-scan option but the HD seems to be always reading something...
When this HD was plugged on my computer the light was on during access only.Is it OK? I mean, isn't something that will decrease the HD lifespam? Is there a way to tell the E4200 to not access the HD when nobody is using it?
View 2 Replies
View Related
Oct 29, 2011
the power light on my wrt54g v2.2 router keeps blinking and it wont connect to the internet when connected
View 3 Replies
View Related
Jun 19, 2012
My Linksys X2000 still working but only red power light on (at nomal there are 3 white light on).
View 3 Replies
View Related
Jan 6, 2013
I am having a problem with my ea4500 several times a day the cisco light flashes and I loose internet connectivity. I have tried resetting the router by the reset button and changed ssid name, making two different one for each band, and still I am having a problem. I have read where it could be a firmware update, I have updated (using current version)
View 6 Replies
View Related
