I have a new e2500 router and want to use my old WRT54G2 to expand the range of the wireless to reach my detached garage. My house is wired with category 5e cabling, but not the garage, which is why i want to wireless to get expanded. I was hoping the the new e2500 would reach, but it doesn't. How I can do that?
View 6 Replies
I'm constantly losing wifi connection and having to restart my Linksys E2500 router
View 4 Replies View RelatedRange is not good for my E2500 router. My house is on one level and spread out quite a bit. Have the router near my main computer. If I take my laptop or Iphone into my bedroom (about 70 feet away-thru 3 interior walls), I have no wi-fi. If I put the router in the middle of the attic
View 4 Replies View RelatedMy wireless router in my downstairs office won't reach an upstairs bedroom on the other side of my house. I'd like to extend the range. It is not clear if my best option is to get an antenna to boost the range (such as an Alfa 500mW AWUS036H USB Wireless Adapter 802.11 b/g Network Radio Card. Includes 2dBi Omni Antenna ), or to get a repeater to repeat the signal, such as a Hawking HWREN1 Hi-Gain Wireless-300N Range Extender. I also don't know if Linksys has a product for either application that works with 802.11n standard.Finally, since the Linksys E2500 has no antenna or antenna port visible, I am nod sure if an antenna such as the Alfa listed above or a Hawking HSB2 HiGain Signal Booster would even work with the E2500.
View 3 Replies View RelatedWhich one have the best range ? I know that the E1500 has SpeedBoost feature but does it matter ? I can get both for the same price.
View 1 Replies View RelatedMy main router is connected to the modem and is an E4500 (upstairs on one end of house). It has a wired connection to the E2500 (downstairs on the other end of the house). I want the same SSID transmitted from both routers.
How do I configure the E2500 to transmit the same SSID as the E4500 to I ahve a consistant signal over the whole house?
Is there a way to block a range of IP addresses in the E2500? Like parental controls but with IP addresses instead of URL..
View 2 Replies View RelatedI have the following equipment
E2500 wireless N router (2 of these)
WRT54g router (B/G)
WAP54g access point (B/G)
I am planning to set up a Wi-Fi network for a single story motel. It is C-shaped; about 300 feet along the longest side with "legs" of 120 and 70 feet.Until now I have only used that single WRT54g in the office for the entire property and it covers about half the property (left side.) My plan starts in the office (bottom left) with a WRT54g connected to the DSL modem as it always was. That would be connected to one of the E2500s in the middle so it can cover the most area. From there two others would shoot out to each corner (the other E2500 and the WAP54g). They will all be wired together with Cat 5e "riser cable". The routers will be placed in a wide open attic.
1. I have heard that N routers have a range of 150ft in every direction so that's why I'm putting one in the middle. Keep in mind that while the attic is open and wood constructed, the walls between rooms are concrete firewall and they haven't been wi-fi friendly.
2. Does starting with a B/G router at the modem mean the N routers will revert to B/G?
I have an E2500 running as a router/DHCP server. For reasons beyond the scope of this question, I am replacing the router and DHCP functions with a SonicWALL device. I would like to continue to use the E2500 as a wireless access point only, providing WiFi connection to the SonicWALL. How do I set up the E2500 for this purpose. I assume I switch off the DHCP server and NAT within the device. Is there a dedicated "access point" mode?
View 9 Replies View RelatedHave set up Router OK. Created Flashdrive EZ
How do I connect my IPAD now to WiFi since there is no USB port on my Ipad??
I have a Cisco e2500 dual band router.I have a cable modem pulling down 55mps.When I put it through my router I get 22mps wireless and 55mps wired. I want my wireless speed as fast as it can go!I have changed channels, I have gone with just wireless N I have done just Mixed. I contacted customer support and they won't talk to me since I am out of warranty (I just not got internet this fast).One small caveat - when I take the channel selection off auto and change to a preffered channel my one laptop drops connection a lot. We have two laptops and both get the same speed. (No I am not running speed tests with a bunch of other things running etc)
View 6 Replies View RelatedWhen I try to connect new iPhone 4S, it goes to the page for all the info (IP address, etc.) instead of just asking for the password input. I've tried disconnecting router and restarting, plugging iPhone into iMac laptop, etc. (PC is hardwired into server and PC laptop, iMac laptop and former iPhone 3 all connected to wifi w/o difficulty.) Went to site of purchase (12/2011) of Lynksys E2500. They suggested might need to download a driver.how to locate and install updates to driver for E2500 to allow connection to iPhone 4S?
View 2 Replies View RelatedI have an existing home network with a D-link wireless router, IP 192.168.0.1. In the past, I set up another of the same model Dlink router as a WAP to extend my network by simply disabling DHCP and setting its IP to 192.168.0.100. Used the same SSID and passwords, worked flawlessly. Now, my WAP-router has failed and I purchased a LINKSYS E2500 to replace it in that function. I'm trying to configure it the same way but am having problems.The Linksys' IP is 192.168.1.1 by default. I hooked its LAN port to my laptop and accessed the setup page at 192.168.1.1. I changed the router IP to 192.168.0.200 and disabled DHCP. I saved settings, the router reset, and since, I am unable to re-connect to that router setup screen at either 192.168.0.200 OR the default 192.168.1.1. I reset the router to default and tried this multiple times but could never get back to the setup page (didn't even configure any wireless settings yet) after I made the IP change and disabled DHCP. With my previous router, this worked easily and flawlessly.
1. What am I doing wrong (ok, other than using Dlink components)?
2. Should these two different brand components work ok together llike this or is that a problem?
3. Why should unticking DHCP and/or changing the IP address as described make the device unreachable?
I have a cordless phone which broadcasts on 2.4ghz - when the phone is being used it cuts out the wifi. I thought that with the E2500 being a dual band - I wouldn't have this issue as I thought the router would switch to the 5 Ghz frequency if there was interference on the lower band. Maybe I am not understanding how the dual band works.
View 3 Replies View RelatedMy WiFi is slow on my laptop and it keeps dropping my LG connect 4G phone.
View 1 Replies View RelatedA few weeks ago I purchased an E2500 router for wireless wi-fi in my home. I inserted the installation disc and started going through the process, but my hard drive on my MacBook so I couldn't finish setting up the router. I have borrowed someones PC laptop, but it doesn't have a CD drive. Is there any way I can set up the router on line or any other way? Will the set up work for Macs and PC's?
View 2 Replies View RelatedI have just upgraded my Linksys router from an older one to the E-2500 about a week ago. Everything is working great on my wired desktop and 3 wireless laptops except the printer will no longer work from any of the computers. I've checked the printer wireless settings and they are correct (ssid and password) and it says it's connected to the wlan. Each of the computers shows the printer is active and set to default BUT the port light on the back of the new router is not on. I have changed cables and still no light, the printer is set up for sharing and it did work a couple days ago but port light was on then.
I have not added anything that wasn't hooked up on my old router, I"m just trying to get what I had on the old router to work on the new one. Everytime I call support, they have me change something that messes up what a previous agent had me do. Now they want me to pay for a direct connection so they can upgrade my router firmware...they didn't even ask what version I already had which happen to be the same version that is available on [URL] so if I had agreed, I would have paid for nothing. I had already paid $29.99 for additional 14 day support on my old router only to find out I needed a new one.
I've been using Linksys routers for quite awhile but I'm just about ready to change brands. I would really like to give this E-2500 a chance.
I am trying to extend the wireless network at our church beyond a firewall to another area of the builing. We have a cat 5 cable run through the firewall to the other side. I have a brand new Linksys E2500 router. Can I assign an IP to this router and connect it's WAN "Internet" port to one of the ports on the main router that is connected to the cable modem and use it to extend our network?
View 1 Replies View RelatedI cant find any wds setting in the UI.I want to bridge my old route for wifi expanding
View 3 Replies View RelatedI am using an E2500 as an access point, which is working fine. I have an Ethernet cable on one of the LAN ports of the E2500 connected to a LAN port on my gateway router. The LAN address of the E2500 is 192.168.7.3 and the LAN address of the gateway router is 192.168.7.1. Clients on the E2500 wireless network have no problems getting to the Internet through the gateway router. Clients on the E2500 wireless network can reach the E2500 local management port at 192.168.7.3 on port 80. On the gateway router I am forwarding WAN port 8083 to LAN address 192.168.7.3 at port 80. But I cannot access the E2500 local management interface via the gateway router. The E2500 should see the request as from 192.168.3.1 due to NAT in the gateway router, right? I can reach any of my actual access points this way, just not a router being used as an access point. Security/design limitation of the router?
View 2 Replies View RelatedI just upgraded from a WRTG 54 version 2 wireless router to the Linsksys E2500. The reason for the change is to send a stronger wireless signal strength further in my house. Setup was easy to my laptop and XBox 360 but my Samsung Internet TV is another story. I can get my tv to get the wireless signal but when I click on an app nothing but error messages. Often times it will say to check my dns settings but I am not that tech savvy and don't know what to do.
View 9 Replies View RelatedI have a cisco WAG120N with me.wifi range is very less, means my devices won't catch the wifi even if they are 5 meters away from the router. Ways to increase the wifi range of this router. I dont want to use any repeater or any such stuff, just want to achieve a far more range with te existing device.
View 9 Replies View RelatedJust bought the linksys E2500 as an upgrade for a my Trendnet 150 wireless N router. I have a motorolla surfboard modem with time warner roadrunner cable internet. After connecting the router I have no internet connection. I do not get a light on the WAN connection after the ethernet cable is attached. I know the light works because when I power it on all the lights come on. I cloned the MAC address but this did not work. I have searched the forums for hours and tried different ideas to no avail. My PC recognized the router and I'm able to get to all the settings but cannot establish a connection from the router to the modem. I also tried different ethernet cables to eliminate that possiblilty.
View 4 Replies View RelatedI purchased an E2500 router today and it worked perfectly for about 4 hours. Now it drops my internet connection constantly. I can connect and load maybe 2 pages before that little yellow triangle of doom appears. Then after 2 or 3 minutes I am good and can reconnect. This cycle just keeps happening.
View 1 Replies View RelatedCurrently running Windows 7, with internet explorer. I have most recent firmware installed on my e2500. The unit drops wireless connectivity on an intermittent basis. Sometimes after 5 minutes and sometimes after 20 or 30 minutes.
View 9 Replies View RelatedI just purchased a E2500 wireless router to upgrade from the previous G- router which I was using. I'm not very experienced in tech issues and would like to know, what would be the easiest way to extend my wireless signal through out the house. The E2500 which I just purchased does not cover all the areas in my household.
View 1 Replies View RelatedI've been having issues with my e2500 router. I've found my connection dropping occasionally both with a wired connection and wirelessly on other computer. My desktop is connected directly to the router via ethernet and I've been keeping an eye on my network preference pane. Every 10 minutes or so the connection will be lost and computer says the cable is unplugged. It then resolves after 2 minutes.
I'm running OSX 10.8, firmware 1.0.07. Done a factory reset, power cycles etc. Configured with Cisco connect and manually multiple times. I've swapped out ethernet cables just to be sure it wasn't a cable issue.
Internet is fine when I've got the computer hooked up directly to the modem. No connection issues.
I have a Linksys E2500 Firmware Version: 1.0.03 and am using the "IPSec Passthrough" for work. On a typical day I'll sign in to my work's VPN, do my work, sign off in the evening, and read my personal email with a direct connection to the internet.
Then on the next morning, I am unable to connect to work until I go to http://192.168.1.1/index.asp and click "reboot." And as soon as the modem finishes rebooting, my laptop can connect to work. I've tried this several days in a row now, and indeed all I need to do to get the VPN passthrough working is rebooting the modem.
Nothing under "Applications & Gaming" is set. I've seen some posts about having a trigger on UDP port 500, but I'm not quite sure how to translate it for the E2500. Plus I'd rather the router "just work" day after day for VPN and everything else, like my old router did! Is there some other setting to try or clearer directions for a bulletproof IPSec passthrough on that unit?
I already have a desktop and modem at home, but I recently bought a new Sony Vaio laptop for college. I also bought a Linksys E2500 wireless router so my laptop could have internet access at home.I inserted the Starter Guide CD into my desktop, created my ID/password, and connected all the cables like it instructed me to but I still couldn't connect to the internet. Instead, several windows popped up with messages like, "Found new hardware. Locate and install driver software, "Insert disc that came with Internet Access Server", and "Windows could not find driver software for your device."When I tried to troubleshoot, I get something like this, "There may be a problem with your DNS - Windows attempted to find www. microsoft.com using DNS, but server responded back with unknown."I also tried inserting the disc into the laptop, but I still didn't recieve any internet connection, but it says that my router was connected.I tried following its advice to restart, unplug cables, and wait 2 minutes but none of it seem to work.
View 3 Replies View RelatedI recently purchased a linksys E2500 for my home network. Occassionally, we have dropped connections, on both G and N cards.The router is connected to a corei3-2100 cpu with 6 gb ram and a 1tb hd, running win7 64bit. Ive bought home plugs for my wife's computer(in the house)and.an outdoor wireless antenna (a CCRANE super usb wifi antenna) for my computer in the garage. I still get dropped signals in the garage, which is only about 50 ft from the router. My computer in the garage is an AMD dualcore 4400 with 4 gb ram, and multiple hdds.What else can I do to get a better and more constant connection.
View 1 Replies View RelatedI just bought a new Linksys E2500 router from Best Buy and I need optimizing my router settings so I can get the absolute best performance out of it. Staying connected and keeping speeds high are a must.I have been noticing connections cutting out at time. It is frustrating when I lose my internet.we have ~3000 sq foot house... 3 levels (basement, first, second).We don't use all of these at the same time but we have: 2 laptops, 3 iphones, ipad, and a PS3 for online gaming.
How can I get the absolute best, most reliable connection and speeds out of my router so we don't experience disconnects?I bought the RE1000 range extender... having installed it yet because the install CD that came with it is the wrong CD (It came with the E900 install CD... which is for a router)I bought the N600 USB adapter which I guess is supposed to update your wireless card for your laptop. I am using that but bars seem low..
We are using a domain and Windows Server 2008 machine with DNS/DHCP setup and active to handle traffic on the network. The old router we had was a cheap (~$20) TrendNet that was configured (not by me) without issue to not only allow the server to handle IP's but also allow us to get in to the server remotely via Remote Desktop. My cut sheet says they had a "virtual server" setup.
Anyways, we now are running an E2500 and if I put in the external IP, Subnet, Gateway, and DNS for our internet provider and then disable DHCP on the router, we don't get internet access. I'm missing what configuration I need to get the server to handle all the traffic I guess. The server has DHCP enabled with the router IP address (192.168.1.1) set and the server address is (192.168.1.2). Like I said before it was working fine with our old router and none of the settings on the server have been changed so must be something with the new router.
Do I need to setup something in the advanced routing to get this working? Currently I have DHCP on automatic and DHCP server enabled just so we can get internet access. DHCP services on the server are still on as well. Can't get any access to the server from the outside via Remote Desktop like we could before.
I have an E2500 with the latest firmware upgrade (1.0.03). My configuration is simple, I have a fixed IP from my ISP with fixed DNS servers. I have one computer connected via cable and one connected via wireless and a laptop that gets connected on occasion wirelessly as well. I also have an android phone that I sometimes have the networking turned on and sometimes not. That doesn't seem to be affecting the router either as I've lost connections under both circumstances. The only thing I have different is I clone the MAC address as the ISP has my IP linked to my old Linksys MAC.
The problem is I randomly lose connection to the internet, the home network is still up it's just the internet goes down. I could be on the computer or not, sometimes while browsing sometimes after I browse for a while sometimes before I get started. Fortunately its not happened during one of my online games but it has happened just after I log off the game. It usually happens a couple of times a day.
