D-Link DIR-655 :: Internet Status Light Blinks Very Rapidly
May 11, 2013
I have an older rev a DIR-655 that has served me well. Today I finally upgraded my ISP to cable (from a slower DLS connection) to get reasonable speed/price All is working very well but unlike my old DSL modem the internet status light on the DIR-655 blinks very rapidly all the time instead of when traffic is passed.The new modem is a Motorola SB6141,I am running the latest firmware 1.35NA I went through a complete re-setup to see if that would calm the light but no dice there. (the settings arrived at were basically the same for the old Sprint modem) ,Is there something I am missing or is it time to retire the old DIR-655 for something more current.
View 5 Replies
ADVERTISEMENT
Mar 25, 2013
Region : Others
Model : TL-WR940N
Hardware Version : Not Clear
Firmware Version : 3.11.3 Build 100408
ISP : Telekom
the SYS light, keeps blinking is that normal?
View 2 Replies
View Related
Mar 11, 2013
I have a D-LINK 601 router which has been working fine. I was told by a friend that it is not password protected. I think that I have set it up now with an adm password. The router and the DSL modem is still connected as before, but the Internet LED blinks orange.
View 1 Replies
View Related
Nov 27, 2011
Does a ASA5505 have a limited lifetime warranty? I have a ASA that is not covered on a SmartNet contract, as far as I know of, it is not owned by my company. It has a yellow status light, and will not boot. Will cisco replace it?
View 1 Replies
View Related
Apr 14, 2010
I have a Problem with a ASA 5505 when i power on the ASA the Power LED change to green and the Status light to solid amber. There is no Console output or anything else.
View 9 Replies
View Related
Feb 22, 2012
My Access Point Power Led blinks constantly, Lan led works normally, Wlan led never turns on.
Access Point: D-Link DWL-2100AP
View 6 Replies
View Related
May 9, 2013
I cannot get access into my router because it doesn't seem to have a gateway IP address, although it is assigning my computer an IP address.
View 1 Replies
View Related
May 7, 2012
I have a question, I have an ap (cisco 1130) that began to get the status light flashing orange and light Ethernet and radio are off.I did a factory reset and it was ok ... past 3 days the problem has happened again.I changed the ap with a new but the situation remained.I tested the wiring and everything is ok.the switch port is set up correctly.
View 11 Replies
View Related
Oct 14, 2011
I have an ASA 5505 with status light solid amber color. It is under SmartNet.I'd like to know Cisco will replaced this device with new ASA5505 or upgrade one?
View 2 Replies
View Related
Jun 30, 2011
We have a root AP whose status light is showing solid red. We power cycled it and it still shows solid red. According to the Cisco documentation, this indicates a firmware failure. Unfortunately, we did not get Smartnet with this access points and instead opted for the limited lifetime warranty.
My question is: is there any way to fix the firmware via console? Whether it be through xmodem or what not. I ran debugs on the controller and can confirm that the AP is not communcating with the controller.
It is also weird that the mesh APs that were previously connected to this root AP show a solid red on their status lights and green for their RF LEDs. Shouldn't the status LED be flashing green-amber-red?
View 1 Replies
View Related
Dec 3, 2012
I have TL-WR740N router. ISP should provide me up to 100Mb/s internet speed. Actual measurements shows me about 80 Mb/s. The problem is when I enable 3389 port in Port Triggering my internet speed drops to 2,5 Mb/s. When I disable port triggering, speed become normal again.
View 3 Replies
View Related
May 9, 2011
The internet connection light is blue, i am assuming this means the device thinks that it is connected. However wired or wireless I can't hit any web pages. When I use the internal tools neither can the device ping any address.
I am using:
Firmware 2.00NA
DSL modem ATT-Yahoo-SBC (Speedstream 4100 using DHCP)
I am planning to upgrade the firmware to 2.01NA and give that a shot.
View 1 Replies
View Related
Jul 22, 2011
I previously asked if I should be concerned that the Internet light on my Linksys E3000 router doesn't light up when I have Internet access. Well recently I had to do a reset and I noticed that during the reset it does in fact light up, but it doesn't come on when the router is done with the reset!
View 1 Replies
View Related
Apr 3, 2011
My internet light flashes at times yellow.Some times i lose internet connection .I have never had this problem with my linksys router.
View 3 Replies
View Related
Mar 11, 2012
I reseted my router because I couldn't go in the login so now eveything is green except the earth looking thing next.the power it is orange Cause I really need my internet
View 1 Replies
View Related
Jan 28, 2011
I have had a Dlink dir 615 for some time now and always had a few issues, but nothing a reboot of the router couldn't solve. This time the problem is persisting, though. The wireless signal keeps blinking and on my laptop it says No internet connection. I've rebooted the router, restored the router, rebooted the modem, and nothing seems to work.
View 1 Replies
View Related
May 31, 2012
For the past year or so, 5-6 times a day my router's green internet light will turn red, needing a reset... 99% of its usage is through wired connections and this is the only router in my home.
View 1 Replies
View Related
Mar 3, 2013
Region : Egypt
Model : TD-W8960N
Hardware Version : V1
Firmware Version : 1.4.0 Build 111108 Rel.40398n
ISP : STE
In the past everything was working fine (had same computer connected wireless + wire) never had this disconnection. Now, I have a laptop connected using wireless & desktop wired but this disconnection is becoming so irritating. It is not only that I lose the internet connection, I lose the DSL like (as if the modem is turned off then on) and all my files over the LAN are either lost during transmission or something else.
View 1 Replies
View Related
Apr 11, 2011
Have noticed this in almost a regular pattern. About every 3 seconds the internet light whick is blue most of the time will ocassionally flash white then maybe yellow. Does not appear to interupt internet access yet last only a second (at the longest),so don't know if I would notice. Am connected to DSL modem and see no change it its indicator lights,(traffic, collision, lan), when it occurs on the DIR-655. Have three PC's and a network (LAN) printer as well as wireless enabled. BTW is does not matter if wireless is active. What do the different colors mean ?? Blue = Connected White = Yellow =
View 3 Replies
View Related
Jan 21, 2011
I recently switched from a DSL ISP (Earthlink, Zyxel modem configured as a bridge, pppoE connect) to a cable ISP (Comcast, Arris cable modem, dhcp connect). Basically PC --> DIR615-->Cable modem-->Internets. With the old DSL the Internet activity LED (green, looks triangular) on the DIR615 blinked only when internet activity occurred. With the new Comcast connection it blinks non-stop about 5 times a second! Even if the PC is turned off it blinks. It stops blinking if I disconnect the ethernet cable between router and modem. The connection itself is fine, but if the DIR615 is doing something it should not be doing it might slow the connection down a bit, (or burn something out prematurely?)FYI, the Arris cable modem does not seem to be a router. It takes a cable connection from outside and provides a single ethernet cable and 2 (voice) telephone cables to the house.
View 1 Replies
View Related
May 10, 2013
Region : India
Model : TD-W8961ND
Hardware Version : V3
Firmware Version : S/N: 12B79605315
ISP : BSNL Data One
I had Purchased a brand new TP-Link WifI Modem Router TD-W8961ND with S/N : 12CB5200872 from [URL] and it got delivered few days back. When I am trying to connect it to the internet the modem is not getting connected nor configured. The Power button light, ADSL Light and internet light are continuously blinking and nothing is getting steady. The modem is appearing to be a damaged piece of modem and it is very unfortunate that we have got a modem from flipkart in an unserviceable condition. It came with a warranty of 03 years and I wanted a replacement so that I can use the modem for connecting internet.
View 1 Replies
View Related
Nov 20, 2011
I have a DIR-655 Rev B, in a typical cascaded config: modem > dir-555 > switches & devices, etc.One of the four dir-655 ports is connected to a cheap-o Belink Wifi router which I use as an access point (I only use this because there's one device that only supports WEP). I was debugging a WiFi issue and I pulled the plug on this Belkin just to get it out of the picture. Well, when I did that, EVERYTHING that was connected through the DIR-655 lost connection. (Well, all the wired stuff anyway- not sure about WiFi devices through the DIR-655). I noticed that the port link light for the powered-off device stayed on on the DIR-655. When I unplugged the cable from the DIR-655, everything went back to normal.
So what I'm trying to figure out now is, is this a DIR-655 issue, or is it something screwy with the Belkin? Or Both? I've got to assume that there's some inherent flaw in the DIR-655 that allows something connected to a port to screw up everything that it's hosting.
View 7 Replies
View Related
Aug 6, 2011
I updated the firmware of my DIR601 to 1.02NA, it now only show NA under status for WAN, even though its connected (PPPoE). It worked with 1.01NA. I tried rebooting the router but no effect
View 1 Replies
View Related
Oct 26, 2011
I'm running Windows 7. As stated in the title, once I see the screen blink, I know I have a few moments of connectivity left. The screen will continue to blink, then the wireless network connection icon goes red with an "x" through it. The computer continues to work (albeit with the screen blinking), but with no connection to the Internet. Checking Device Manager indicates no conflicts. Manually pressing the "wireless connectivity button" on this Compaq, which shows green=connected, only turns it red for a second, then back to green as if the adapter is enabled. Doing this prior to the blink-failure cuts the wireless connection as it should. I added iTunes about a month ago, the problem started about two weeks ago.
View 2 Replies
View Related
Nov 19, 2011
I just hooked up my DIR-655 yesterday and it seems to be working very well. The only problem I've got is that the Wireless Status page is empty. It filled in with data one time only, and it showed connections, protocols, speeds, etc. that seemed correct.
View 14 Replies
View Related
Nov 22, 2012
We have lms 3.2 that we are facing a problem with it. When we start the server the EDS-GCF log file size start to increasing rapidly until it consumes up all free space and it only stops when we stop the Daemon Manager service. I tried to do the pds how command but I get no output from it. I included the portion of the EDS and EDS-GCF log files. i searched and didn't find the cause of this error.
View 3 Replies
View Related
Jul 31, 2011
I have a WAG120N, its nearly dead,I tried resetting it many times, it still wouldn't work. The WiFi LED blinks continuously and uniformly. There is no WiFi, no access to router, the only thing that is working is the switch.
View 4 Replies
View Related
Oct 21, 2011
I have had this router for a while now and I have been experiencing these problems for forever. I can't seem to have two Xbox360's stay on OPEN NAT type permanently. I have tried port forwarding both xbox's, just my xbox, just my dad's xbox etc.. I have tried DMZ on one with or without the other on Port Forwarding. I have turned UPNP on I have it so the filtering is set to endpoint independent . I have tried without . I have even tried port triggering today. I have manually set static ip addresses on both the xbox and the router. I even have the most recently upgraded firmware. Now... How do I get TWO Xbox 360's on OPEN NAT ? How to get two xbox360's on permanent OPEN NAT status.
View 6 Replies
View Related
Nov 28, 2012
We have approximately 150 1142 LWAPP's deployed in our facility. Recently we started getting complaints about speed issues (90% are using G 10% N). Upon investigating we found that the speeds are fluctuating rapidly. Everything from 54Mbps down to 1Mbps and back up again. I've confirmed that this will happen while standing next to an AP (and confirming connectivity to it), however I cannot find anything wrong or anything that has changed with our configuration. We are a large facility and it is happening all over the campus, so I'm fairly certain it isn't any type of 'normal' interference.
View 7 Replies
View Related
Nov 5, 2012
I'm trying to use my installed (working, clean) SD card, but on the SD management screen doesn't list it. Instead, where the SD status is it says "SD Status : Reinitialization". I'm a techie guy so I've done all the standard things you'd try: I've made sure it's pushed in all the way, that it's in the right way (it really only goes in one way), and that's it's a writable (tried it on another device). I've also upgraded the firmware (it was almost current already), reformatted the card, reset and restarted the device, etc.
View 8 Replies
View Related
Oct 10, 2012
I have connected my 2504 to a 3560 switch via a UTP SFP on a Gig port.
I have my management on 10.0.0.x I have tried tagging the port and untagging.
When I connect to the 3560 the interface comes up a-1000 a-full but when I look on the WLC the port I am using, port 1, shows Link status down.
The green light is on both the WLC port and the 3560 port but I cannot get the link status to come up on the WLC nor can I ping the WLC.
It must be something dumb I have missed.
The WLC port is autonegotiate too.
View 7 Replies
View Related
Apr 22, 2011
i have an RTA1025W router. When i plug a network cable into it nothing happens. When i power it down with the cable still plugged in when it boots the LAN1 led flashes rapidly then stops? Then no connection to it via the PC?
View 3 Replies
View Related
Jan 21, 2013
We recently installed 15 of these switches, and we're having a few odd, random network issues. But before I enumerate those issues, I have a simple question: are the connection lights on these switches *supposed* to blink rapidly? Or are they supposed to blink *normally*?On all other switches I've ever seen / worked on / worked around, when a cable is plugged into a port, the connection lights blink upon network activity. sometimes they blink a little faster when there's lots of activity, but mostly it's an almost lazy, random kind of blinking. When you look at a switch and every light on every port that's connected is blinking very rapidly, your first instinct is "No *wonder* nothing works around here!" and you find the port that's chattering and unplug it...all the blinkies go back to normal.Well, on the 15 switches we've installed, every light that's on blinks rapidly, as if there's an uncontrolled storm going on. Is that the "new norm"? Did I miss the memo, and there is nothing to be worried about here? Or are the rapidly blinking lights telling me there is, indeed, a problem?
View 4 Replies
View Related
