D-Link DIR-825 :: Get 2 Xbox360 On Permanent Open NAT Status?
Oct 21, 2011
I have had this router for a while now and I have been experiencing these problems for forever. I can't seem to have two Xbox360's stay on OPEN NAT type permanently. I have tried port forwarding both xbox's, just my xbox, just my dad's xbox etc.. I have tried DMZ on one with or without the other on Port Forwarding. I have turned UPNP on I have it so the filtering is set to endpoint independent . I have tried without . I have even tried port triggering today. I have manually set static ip addresses on both the xbox and the router. I even have the most recently upgraded firmware. Now... How do I get TWO Xbox 360's on OPEN NAT ? How to get two xbox360's on permanent OPEN NAT status.
View 6 Replies
ADVERTISEMENT
Jul 6, 2009
I cannot get my NAT open for my xbox360
View 5 Replies
View Related
Jul 19, 2011
I cant really find anything about MAC address filtering in the tabs of the router administrator page.
View 7 Replies
View Related
Aug 10, 2011
I'm using a Thomson Technicolor 587nV3. I need to change my NAT status from strict to open. So I can play MW3 online and connect to my friends online games and so I can host multiplayer matches. I have windows 7 laptop to do any of the steps required. I've tried to bind my routers cone through Winscript but without any luck perhaps I done it wrong
View 5 Replies
View Related
Aug 6, 2011
I updated the firmware of my DIR601 to 1.02NA, it now only show NA under status for WAN, even though its connected (PPPoE). It worked with 1.01NA. I tried rebooting the router but no effect
View 1 Replies
View Related
Nov 19, 2011
I just hooked up my DIR-655 yesterday and it seems to be working very well. The only problem I've got is that the Wireless Status page is empty. It filled in with data one time only, and it showed connections, protocols, speeds, etc. that seemed correct.
View 14 Replies
View Related
Nov 5, 2012
I'm trying to use my installed (working, clean) SD card, but on the SD management screen doesn't list it. Instead, where the SD status is it says "SD Status : Reinitialization". I'm a techie guy so I've done all the standard things you'd try: I've made sure it's pushed in all the way, that it's in the right way (it really only goes in one way), and that's it's a writable (tried it on another device). I've also upgraded the firmware (it was almost current already), reformatted the card, reset and restarted the device, etc.
View 8 Replies
View Related
May 11, 2013
I have an older rev a DIR-655 that has served me well. Today I finally upgraded my ISP to cable (from a slower DLS connection) to get reasonable speed/price All is working very well but unlike my old DSL modem the internet status light on the DIR-655 blinks very rapidly all the time instead of when traffic is passed.The new modem is a Motorola SB6141,I am running the latest firmware 1.35NA I went through a complete re-setup to see if that would calm the light but no dice there. (the settings arrived at were basically the same for the old Sprint modem) ,Is there something I am missing or is it time to retire the old DIR-655 for something more current.
View 5 Replies
View Related
Oct 10, 2012
I have connected my 2504 to a 3560 switch via a UTP SFP on a Gig port.
I have my management on 10.0.0.x I have tried tagging the port and untagging.
When I connect to the 3560 the interface comes up a-1000 a-full but when I look on the WLC the port I am using, port 1, shows Link status down.
The green light is on both the WLC port and the 3560 port but I cannot get the link status to come up on the WLC nor can I ping the WLC.
It must be something dumb I have missed.
The WLC port is autonegotiate too.
View 7 Replies
View Related
Jul 10, 2012
I have a VM (Alice).I want to route ALL its traffic through a server of my own in the UK.It needs to be 'fail-safe' in the sense that the traffic must either be routed through the server, or not at all (EG with windows VPN dialer, if the VPN connection is dropped it will immediately begin routing traffic normally again - that's not acceptable*). I need to run windows on the VM, the server can be anything.The VM is connected to the internet via a linux firewall/router box in my house (set as default gateway for the VM).How can I set this up?
View 5 Replies
View Related
Nov 18, 2011
I have a network printer which is connected to unmanaged switch, then unmanaged switch is then connected to one of the slots on the router (to get internet access). I use the program Free IP Scanner to look for the IP so then I can find the IP address of my printer. Then I would go to Port setting of the printer and change. Every week or month I have to do this. Two things I would like to know:
1. I have a 2003 server which is not connected or active yet. it's just sitting there running but no computers or printers are connected yet. How do I make this to be a printer server and solved my issue of having keep tracing the IP for my printer?
2. If not using the server, how would I setup my printer IP address to be permanent?
View 3 Replies
View Related
Feb 16, 2013
Region : India
Model : TL-WR740N
Hardware Version : Not Clear
ISP : BSNL BB
I have a BSNL BB connection. When I use the connection directly, without adding TP Link router, all the websites open flawlessly. Once when I connect the wireless router, certain websites for example Yahoomail, pepperfry.com, yepme.com don't open at all. These are just examples, but I'm unable to access many sites which is a bit annoying. But sites such as gmail, youtube, facebook open clean, there are no issues. I didn't make any configuration changes too. I tried it more than three or four times, but there is a restricted access only.
View 4 Replies
View Related
Sep 26, 2010
My wireless connection for my laptop is showing upas N on Win 7 but G on DIR-655 status page??? I'm confused. Am I getting N speeds/coverage or stuck with G. If G, why? I've tried wiping my wireless network config. on Windows and reestablishing it, but no change. The DIR-655 config page shows my machine connected at 54 Mbps and Type as G
View 8 Replies
View Related
Feb 4, 2013
Region : Italy
Model : TL-WR740N
Hardware Version : Not Clear
Firmware Version :
ISP : Alice (Telecom)
I bought some days ago Tp-Link Wireless Router (Model TL-WR740N - 150 Mbps - Ver 4.23) but I couldn't install it: when I do Easy Setup Assistant, the network status test always fails because of absence of connectivity. I can see that there are some problems by the lights of the router: the WLAN light switches on, as the WAN light and the LAN light, instead of being flashed. I tried to do the installation without cd but, clicking on 192.168.1.1, I didn't find the page to access to web console but the Telecom page of the status of my connexion (nb: it reports that ethernet is unplugged).
View 3 Replies
View Related
May 7, 2008
I am trying to install a AIR-BR1310G wireless link between two buildings. I configured the setup in a lab and had everything functioning. Shipped it to the client who is now trying to install it. The radio link is up, but we are having issues with the remote Ethernet connection.The root bridge is connected to a WS-C3560G-24TS (core) switch. The port is setup as a trunk with a native vlan of 2 (our management vlan). [code] if I do a "show power-injector" on the remote radio (no Ethernet link), I get: "Received zero AutoMIB packet from Power Injector, Check to see if CDP is disabled on Fast ethernet" repeating. No other entries. If I do the same command on a unit with a link (root bridge) I get information about "Power Injector Port 0 speed 100Mb/s duplex full link up enabled yes" with a bunch of stats. Similar for "Power Injector Port 1". Power Injector Ports 2-4 as "down" and 5-6 as "disabled". Other than the 3 different patch cables they tried (all straight through) or a crossed cable (try tomorrow when they buy one), is there any other reason the port won't go Up/Up?
View 3 Replies
View Related
Jan 12, 2012
I need a place to share files between a few other people that:
1. Is fast and easy, like sharing files on a local network with gigabit hardware. Why not do exactly that? (see next point)
2. Has a permanent address to access the files, as if it were hosted on a website. The reason for this is the software I will be using to point to these files does not use relative paths. If it did use relative paths, I was simply going to setup a shared dropbox with all the files, but alas, that does not work. I want this solution to be future proof, so that no matter how much I change my setup, the file paths that my software is looking at will always remain the same.
3. (optional, but preferred) Ability to automatically backup these files. Like an rsync with amazon S3 or something.I am guessing there is a simple and widely used solution to this, like an ftp setup, just not sure how it all works.
View 6 Replies
View Related
Nov 18, 2011
I configured an IPSec VPN tunnel between two ASA 5505 firewalls. I would like to make sure that the IPSec tunnel (hence the security association) is permanent and do not drop due to idle condition.
View 2 Replies
View Related
Feb 21, 2012
Why the IOS on 4500 doesn't support globally, although am running the IOS 12.2,need for logging event link-status global.
View 3 Replies
View Related
Mar 21, 2012
I am very newbie to networking. Although I am a newbie I managed to install Windows Server 2003 by following instructions got from Google but have not played around completely. I have 2 PCs with XP, 1 unmanaged switch. If I connect the 3 PCs (2 Xp clients + 1 server) using one unmanaged switch,
1. how do I setup the server to be able to give permanent IP to each PC (clients)?
2 how do I make the 2 PC be able to access the server?
View 2 Replies
View Related
Oct 29, 2012
I understand that most of the cisco switches does not have a battery-supported system clock. The better solution is to setup the NTP server and let the rest of the switches to synchnorise the clock with it. How about cisco switch 4948? Does it have a battery-supported system clock?If the cisco switch 4948 is the NTP master, how I am going to make sure that the clock will not be reset after reload?
View 3 Replies
View Related
Nov 18, 2012
My xbox360 will not connect to my wifi it say theres a problem with the modem
View 1 Replies
View Related
Feb 17, 2012
I was previously using SDM for our Cisco 2811, and this past week installed CISCO Configuration Professional so I could have access to a bandwidth/traffic monitor.
I have successfully started the monitoring service and monitored traffic from within CCP, but it appears that if I turn off the computer I am using to monitor the traffic, it stops collecting data until I start CCP and the monitor up again.
Is there a way (maybe with IOS console commands) that I can have the monitor always running, so I can pull up, say, a week's worth of info at any time? Leaving the computer on all the time is not an option, and currently I have only a few days of data, then a big empty chunk, and then what I have collected since I started it back up today.
View 1 Replies
View Related
Jan 3, 2011
I am using a HP laptop and its wireless connection is coming from my schools Wireless service which requires a ID and password each time you connect. I would like to funnel this wireless connection to my xbox 360 via a ethernet cord.Ive researched this a bit and found plenty guides but nothing has worked for me. I saw this in a previous post"Bridging two network connections:1. Make sure the secondary connection has DHCP enabled.. Open the Network Connections folder from the Start Menu, Settings.3. Select the first connection to be used in the bridge and highlight it by left clicking on it.4. Holding the Ctrl key, select the second connection to be used in the bridge by left clicking on it.5. Right click on one of the two highlighted connections and select Bridge Connections."
View 14 Replies
View Related
Feb 1, 2012
how do i find my web key on my computer to set up xbox360 live?
View 3 Replies
View Related
Oct 29, 2011
i'm trying to connect my xbox360 to the internet. I'm upstairs, my modem and router are downstairs. I'd prefer not to have to get a wireless adaptor for my xbox, but if that's the only way, i'll settle with that.We have Comporium internet. I can get cable if I hook a cable box up to the coax port in the wall upstairs. I have been looking at coax to ethernet adaptors, hoping I could go from the coax in the wall, to the adaptor, right into the back of the xbox. Is this possible?
View 1 Replies
View Related
Apr 28, 2012
I'm dessigning a network and this is my scenario:
5 - Remote sites (no static IP there)
3 - Remote users (comercial)
1 - Central building (using static ip address)
Is it possible to establish a permanent vpn tunnel between each one of my remote sites to the main building, even if I have no static IP address in the remote sites?
Do you think that RV180 is the best choice to mannage vpn connection between remote sites and the central building securely and faster?
View 2 Replies
View Related
Mar 16, 2013
I wanto delete the Evalution License and i want to activate the permanent license. find the attached snapshot of License.
View 7 Replies
View Related
Aug 6, 2011
i just got my xbox 360 with built in wifi and it say connect to xbox live for free but it shows o ther people in my area but thiers is locked
View 1 Replies
View Related
Jun 25, 2011
My Xbox360 is wanting a WEP key for my network so that I can connect wirelessly via external networking adaptor. I've been told by Apple techs that my Airport isn't compatible with Airport Utility software, so they can't find my WEP key.
View 8 Replies
View Related
Dec 28, 2011
We are trying to play Call of Duty MW3. We have purchased two games and two xbox360s. We want to connect the two xboxs to the internet using a cisco wag120n router..
View 2 Replies
View Related
Feb 9, 2012
I have a new E4200 on the way to replace my lackluster dlg-4500 and I need to find out the best settings and inputs for setting up 2 xbox360(both wired), and a PS3(wired) as well as my other wireless toys. What I want to find out are the settings that will make the router run the best.
View 1 Replies
View Related
Dec 26, 2006
I recently purchased a new router (WRT54G Ver.6) and the initial setup went well. however, when I try to connect my xbox 360 to this network, the DNS does not resolve and it fails every time. what should I do?
View 2 Replies
View Related
Mar 12, 2011
i have an acer laptop an iphone and an xbox360 running on my connection not always all at once but my connection just randomly cuts out at any point whenever im on xbox live i get disconnected and i look at the router and its just resetting itself and i have to go and reboot it or just reset it and wait a wile before it will come back on. but even when it is on its not for long before it goes off on its own
View 2 Replies
View Related
