Cisco Wireless :: 1300 Series Bridge And FastEthernet Link Status
May 7, 2008
I am trying to install a AIR-BR1310G wireless link between two buildings. I configured the setup in a lab and had everything functioning. Shipped it to the client who is now trying to install it. The radio link is up, but we are having issues with the remote Ethernet connection.The root bridge is connected to a WS-C3560G-24TS (core) switch. The port is setup as a trunk with a native vlan of 2 (our management vlan). [code] if I do a "show power-injector" on the remote radio (no Ethernet link), I get: "Received zero AutoMIB packet from Power Injector, Check to see if CDP is disabled on Fast ethernet" repeating. No other entries. If I do the same command on a unit with a link (root bridge) I get information about "Power Injector Port 0 speed 100Mb/s duplex full link up enabled yes" with a bunch of stats. Similar for "Power Injector Port 1". Power Injector Ports 2-4 as "down" and 5-6 as "disabled". Other than the 3 different patch cables they tried (all straight through) or a crossed cable (try tomorrow when they buy one), is there any other reason the port won't go Up/Up?
View 3 Replies
ADVERTISEMENT
May 13, 2012
i need to configure wireless link between my 1300 series, how can i use them like a bridge and access point in the same time?
Do i need static ip for BVI interfacess between them for bridge or its need to be DHCP, is there any example?
View 5 Replies
View Related
Apr 6, 2008
Is it possible to configure two 1300 series bridges at one location, each handling a bridge link to another location to BOTH backup and load balance for each other should one of them fail?
View 5 Replies
View Related
May 5, 2013
Product/Model Number:AIR-BR1310G-A-K9
System Software Filename:c1310-k9w7-tar.123-7.JA
System Software Version:12.3(7)JA
Bootloader Version:12.3(2)JA4 .
We have several of these bridges hanging around; would like to move them one at a time from our 1030WLSE to our 5508WLC (software 7.0.235, so they're compatible).The bridges are all connected to power injectors (AIR-PWRINJ-BLR2). With our 1200's, we apparently just unplug power, hold mode button, plug in power, release mode after about 4 seconds, and they find the new controller (I haven't tried it yet to confirm, but that's what Google...err...Cisco...says will work!). But obviously there's no "mode" or reset button on either the power injector or the bridge itself.
(Other than "shut down the old controller and the bridges and APs will find the new controller". I'll do that at some point, but want to test first with some spare bridges / APs.)
View 1 Replies
View Related
Sep 14, 2011
I've been getting warning messages from the event log of a 1300 series bridge, which is set as an Access Point in the network, states: 'Packet to client (mac address) reached max retries, removing the client'; I'm not sure why the client is removed. Does 'reached max retries' mean that the client has tried to many times to connect to the AP/Bridge?
View 1 Replies
View Related
Jun 28, 2011
We have 2.5 Mbps connection from an ISP at our branch routers (1800 series)with single physical link terminated on FE0 but have two subinterfaces with separate subnets.
I have applied the following policy-map outbount under physical Interface FastEthernet 0. Show poliocymap output is as follows
Policy Map QoS-OUT
Class Email
priority 512 (kbps)
Class SQL
priority 512 (kbps)
Class File-Copy
police cir 1024000 bc 32000
conform-action transmit
exceed-action drop
Class CCTV
police cir 384000 bc 12000
conform-action transmit
exceed-action drop
But it seems that sometimes( not all the time ) the CCTV traffic seems to exceed the 384k and chokes the entire link(2.5 mbps).
View 4 Replies
View Related
Oct 13, 2012
I understand that the NM-1FE Fastethernet modules are not compatible with Cisco 2600 series routers, just the Ethernet 1-E module. With that being said, are there ANY modules supported by the 2600, 2621 or 2621XM series routers that have fastethernet port(s) outside of the pricey NM-16ESW module? I don't need a 16 port module!
View 3 Replies
View Related
Aug 7, 2012
Looking to put a wireless bridge in to connect 2 building about 2000 feet apart. Excellent Line Of Site from rooftop to rooftop. Very little data traffic but will be running Voice over the link. Any have any input on using the 1300 bridges for this application as a permanent install?
View 5 Replies
View Related
Aug 16, 2011
I have a cisco aironet 1300 series and i need to reset it back to factory default. the directions say push the mode button while the access point is off and then turn it on while the mode button is down.
View 1 Replies
View Related
Oct 11, 2006
I need to know if LAG channel groups can be used to increase capacity of media converted links? (i.e. wireless links).For example.. aggregating two 1300 series wireless bridges via 2 switches.
View 1 Replies
View Related
Nov 19, 2011
I just hooked up my DIR-655 yesterday and it seems to be working very well. The only problem I've got is that the Wireless Status page is empty. It filled in with data one time only, and it showed connections, protocols, speeds, etc. that seemed correct.
View 14 Replies
View Related
Oct 10, 2012
I have connected my 2504 to a 3560 switch via a UTP SFP on a Gig port.
I have my management on 10.0.0.x I have tried tagging the port and untagging.
When I connect to the 3560 the interface comes up a-1000 a-full but when I look on the WLC the port I am using, port 1, shows Link status down.
The green light is on both the WLC port and the 3560 port but I cannot get the link status to come up on the WLC nor can I ping the WLC.
It must be something dumb I have missed.
The WLC port is autonegotiate too.
View 7 Replies
View Related
Sep 24, 2012
We have acquired few AIR-BR1410A-A-K9 AP's that are for US only. I am in Pakistan. For our market, Cisco proposed AIR-BR1410A-E-K9. This is fine as it is listed on their website as well.However, since we also have the "A" model and now the "E" model, can we place an A model on one end and an E model on the other and make them communicate with each other?
View 3 Replies
View Related
Jan 16, 2012
I have recently purchased a linksys cisco E1200 series router and would like to know how to bridge the connection to my xbox
View 1 Replies
View Related
Sep 26, 2010
My wireless connection for my laptop is showing upas N on Win 7 but G on DIR-655 status page??? I'm confused. Am I getting N speeds/coverage or stuck with G. If G, why? I've tried wiping my wireless network config. on Windows and reestablishing it, but no change. The DIR-655 config page shows my machine connected at 54 Mbps and Type as G
View 8 Replies
View Related
Feb 4, 2013
Region : Italy
Model : TL-WR740N
Hardware Version : Not Clear
Firmware Version :
ISP : Alice (Telecom)
I bought some days ago Tp-Link Wireless Router (Model TL-WR740N - 150 Mbps - Ver 4.23) but I couldn't install it: when I do Easy Setup Assistant, the network status test always fails because of absence of connectivity. I can see that there are some problems by the lights of the router: the WLAN light switches on, as the WAN light and the LAN light, instead of being flashed. I tried to do the installation without cd but, clicking on 192.168.1.1, I didn't find the page to access to web console but the Telecom page of the status of my connexion (nb: it reports that ethernet is unplugged).
View 3 Replies
View Related
May 23, 2013
Can we make a bridge connection between cisco aironet 1400 series and cisco R5005? In Root and Non Root Manner.
View 1 Replies
View Related
May 23, 2013
can we make a bridge connection between cisco aironet 1400 series and cisco R5005?
In Root and Non Root Manner.
View 1 Replies
View Related
Jun 5, 2012
Is it mandatory to connect Cisco WLC 2504 to a Gigabit port ?? can we connect it to a fasternet port (100 mbps) ?
View 4 Replies
View Related
Aug 6, 2011
I updated the firmware of my DIR601 to 1.02NA, it now only show NA under status for WAN, even though its connected (PPPoE). It worked with 1.01NA. I tried rebooting the router but no effect
View 1 Replies
View Related
Oct 21, 2011
I have had this router for a while now and I have been experiencing these problems for forever. I can't seem to have two Xbox360's stay on OPEN NAT type permanently. I have tried port forwarding both xbox's, just my xbox, just my dad's xbox etc.. I have tried DMZ on one with or without the other on Port Forwarding. I have turned UPNP on I have it so the filtering is set to endpoint independent . I have tried without . I have even tried port triggering today. I have manually set static ip addresses on both the xbox and the router. I even have the most recently upgraded firmware. Now... How do I get TWO Xbox 360's on OPEN NAT ? How to get two xbox360's on permanent OPEN NAT status.
View 6 Replies
View Related
Jun 19, 2011
my wireless router that is connected to the internet is in the basement and my computer is upstairs on the second floor of my house. Because of this the signal is very bad, to fix this problem I bought a Belkin Wireless N300 in order to create a wireless bridge but I am having trouble. My downstairs router is a D-Link DI-524 and I have googled all over the place to find a solution but the belkin router doesn't have a wireless bridging option...
View 2 Replies
View Related
Dec 7, 2012
I have a Dell Inspiron 1720, that uses a 1300 wireless lan, that keeps crashing. Is there a fix for this, can I replace it with another wireless lan card? Whenever I first start the computer, I would get the error message saying your wireless card had stopped working.
View 4 Replies
View Related
Jan 11, 2013
I have two different LAP 1300 and 1200 in my network and I need to add theme to the WLC,I successes to add one of theme by the option 60 in the DHCP pool at the Core SW,How to use multiple VCI strings for lap 1300 and 1200 (option 60) in one pool?
View 4 Replies
View Related
Feb 20, 2008
I have two Cisco 1300's acting as bridges only. I have created an infrastructure ssid on VLAN 2 and assigned this to the radio. I am carrying multiple VLANs between the bridges (using subinterfaces on the fastethernet and radio ports).I have enabled WPA-PSK, but how do I check that this is being used between the bridges? Also - I have a switch connected at each end of the bridge. When I make VTP changes, the remote switch does not pick these up - is this because VTP goes over VLAN1 regardless of the Native VLAN (2 in my case)? Do I have to carry VLAN1 over the bridge to get VTP working, or is there an alternative solution?
View 7 Replies
View Related
Nov 5, 2012
I'm trying to use my installed (working, clean) SD card, but on the SD management screen doesn't list it. Instead, where the SD status is it says "SD Status : Reinitialization". I'm a techie guy so I've done all the standard things you'd try: I've made sure it's pushed in all the way, that it's in the right way (it really only goes in one way), and that's it's a writable (tried it on another device). I've also upgraded the firmware (it was almost current already), reformatted the card, reset and restarted the device, etc.
View 8 Replies
View Related
May 11, 2013
I have an older rev a DIR-655 that has served me well. Today I finally upgraded my ISP to cable (from a slower DLS connection) to get reasonable speed/price All is working very well but unlike my old DSL modem the internet status light on the DIR-655 blinks very rapidly all the time instead of when traffic is passed.The new modem is a Motorola SB6141,I am running the latest firmware 1.35NA I went through a complete re-setup to see if that would calm the light but no dice there. (the settings arrived at were basically the same for the old Sprint modem) ,Is there something I am missing or is it time to retire the old DIR-655 for something more current.
View 5 Replies
View Related
Dec 10, 2012
Region : UnitedStates
Model : TL-WR940N
Hardware Version : Not Clear
Firmware Version : latest
ISP : Time-Warner
Just purchased the WR940N to use as a wireless bridge. I expected to be able to have the router join my wireless network, and provide Ethernet connectivity to 4 devices behind it. But I'm missing something in the configuration. I can get it on the wireless network, and manage it via the wireless network. But devices plugged into the Ethernet cannot get out to the Internet. Basically, I have a 192.168.1.x network, and the router is node 192.168.1.3 on the wireless network. I've turned off the firewall and DHCP on the router. The Ethernet devices behind it get an address from my network, but the router inserts its own address in as the default gateway, and my Ethernet devices do not have a route to my 192.168.1.x network, despite having an address on it.
View 4 Replies
View Related
Jun 27, 2012
Iv got an "old" dir 655 laying around as my secondary router and found out it had an USB slot for share port.In another room of the house Iv got a media center and an Usb printer. Can I use this dir 655 as a wireless bridge from my main router, so the media center and the printer can be connected? So both low level streaming and shared printer with share port.Or do you need to be connected directly to the dir 655 to use the usb and share port?
View 11 Replies
View Related
Jan 28, 2010
I want to send a WoL (wake on lan) packet to power up a PC which is wired to DAP-1522. The DAP-1522 is connected to my DIR-655 router wirelessly. So far, I have no luck. Do you know if the DAP-1522 is capable of passing the WoL? Does it need a firmware upgrade before it can do so?
View 7 Replies
View Related
Nov 15, 2011
i just happened to have a spare DIR 601 and I already installed DDWRT on it. Now my question is can make this as a wireless bridge or repeater? with only using the signal of my DIR 655 router upstairs?
View 4 Replies
View Related
Oct 16, 2012
I purchased a D-Link DGL-4500 to replace my aging WRT54G around a year ago, only to find it nowhere near as reliable. It's been collecting dust since.I'm wondering if there is a way to use it as a wireless bridge so I can connect it to my home network and then use it's ethernet ports to provide network access to several devices.
View 2 Replies
View Related
Jul 24, 2011
I'm looking at purchasing a Linksys E4200 to replace my WRT54G router, however I also need a Wireless N bridge so I can use it to hook up my HTPC and XBox that's located in my living room.
I'd like to get a bridge that has 4 LAN ports .
View 7 Replies
View Related
